scholarly journals Quantitative Evaluation of the Thermal Heterogeneity on the Surface of Cryotherapy Cooling Pads

2014 ◽  
Vol 136 (7) ◽  
Author(s):  
Sepideh Khoshnevis ◽  
Jennifer E. Nordhauser ◽  
Natalie K. Craik ◽  
Kenneth R. Diller
Keyword(s):  
Image Analysis ◽  
Temperature Distribution ◽  
Distribution Patterns ◽  
Temperature Fields ◽  
Spatial Gradient ◽  
Temperature Profiles ◽  
Operating Characteristics ◽  
Nonuniform Temperature ◽  
Quantitative Examination ◽  
Thermal Heterogeneity

We have investigated thermal operating characteristics of 13 commercially available cryotherapy units (CTUs) and their associated cooling pads using IR imaging. Quantitative examination of the temperature profiles from pad IR images shows diverse, nonuniform temperature distribution patterns. The extent of heterogeneity of the temperature fields was quantified via standard image analysis methods, including thresholding, spatial gradient diagrams, and frequency histogram distributions. A primary conclusion of this study is that it is a misnomer to characterize the thermal performance of a CTU and cooling pad combination in terms of a single therapeutic temperature.

High-speed isotachophoresis. Analytical aspects of the steady-state longitudinal temperature profiles

1979 ◽  
Vol 44 (3) ◽  
pp. 841-853 ◽  
Author(s):  
Zbyněk Ryšlavý ◽  
Petr Boček ◽  
Miroslav Deml ◽  
Jaroslav Janák
Keyword(s):  
Steady State ◽  
Temperature Distribution ◽  
Electric Field ◽  
Field Intensity ◽  
Electric Field Intensity ◽  
Minor Component ◽  
Physical Models ◽  
Temperature Profiles ◽  
Longitudinal Temperature ◽  
Continuous Character

The problem of the longitudinal temperature distribution was solved and the bearing of the temperature profiles on the qualitative characteristics of the zones and on the interpretation of the record of the separation obtained from a universal detector was considered. Two approximative physical models were applied to the solution: in the first model, the temperature dependences of the mobilities are taken into account, the continuous character of the electric field intensity at the boundary being neglected; in the other model, the continuous character of the electric field intensity is allowed for. From a comparison of the two models it follows that in practice, the variations of the mobilities with the temperature are the principal factor affecting the shape of the temperature profiles, the assumption of a discontinuous jump of the electric field intensity at the boundary being a good approximation to the reality. It was deduced theoretically and verified experimentally that the longitudinal profiles can appreciably affect the longitudinal variation of the effective mobilities in the zone, with an infavourable influence upon the qualitative interpretation of the record. Pronounced effects can appear during the analyses of the minor components, where in the corresponding short zone a temperature distribution occurs due to the influence of the temperatures of the neighbouring zones such that the temperature in the zone of interest in fact does not attain a constant value in axial direction. The minor component does not possess the steady-state mobility throughout the zone, which makes the identification of the zone rather difficult.

scholarly journals A Method for Reconstruction of Boiler Combustion Temperature Field Based on Acoustic Tomography

2021 ◽  
Vol 2021 ◽  
pp. 1-11
Author(s):  
Yuhui Wu ◽  
Xinzhi Zhou ◽  
Li Zhao ◽  
Chenlong Dong ◽  
Hailin Wang
Keyword(s):  
Temperature Field ◽  
Temperature Distribution ◽  
Optimal Parameter ◽  
Interpolation Method ◽  
Least Square Method ◽  
Reconstruction Algorithm ◽  
Least Square ◽  
Temperature Fields ◽  
Acoustic Tomography ◽  
Measured Temperature

Acoustic tomography (AT), as a noninvasive temperature measurement method, can achieve temperature field measurement in harsh environments. In order to achieve the measurement of the temperature distribution in the furnace and improve the accuracy of AT reconstruction, a temperature field reconstruction algorithm based on the radial basis function (RBF) interpolation method optimized by the evaluation function (EF-RBFI for short) is proposed. Based on a small amount of temperature data obtained by the least square method (LSM), the RBF is used for interpolation. And, the functional relationship between the parameter of RBF and the root-mean-square (RMS) error of the reconstruction results is established in this paper, which serves as the objective function for the effect evaluation, so as to determine the optimal parameter of RBF. The detailed temperature description of the entire measured temperature field is finally established. Through the reconstruction of three different types of temperature fields provided by Dongfang Boiler Works, the results and error analysis show that the EF-RBFI algorithm can describe the temperature distribution information of the measured combustion area globally and is able to reconstruct the temperature field with high precision.

Evaluation by FEM of the Influence of the Preheating and Post-Heating Treatments on Residual Stresses in Welding

2014 ◽  
Vol 627 ◽  
pp. 93-96 ◽  
Author(s):  
Raffaele Sepe ◽  
Enrico Armentani ◽  
Giuseppe Lamanna ◽  
Francesco Caputo
Keyword(s):  
Temperature Distribution ◽  
Residual Stresses ◽  
Gas Metal Arc Welding ◽  
Welding Process ◽  
Element Model ◽  
Butt Joint ◽  
Temperature Fields ◽  
Heating Process ◽  
Butt Weld ◽  
Metal Arc Welding

During the last few years various experimental destructive and non-destructive methods were developed to evaluate residual stresses. However it is impossible to obtain a full residual stress distribution in welded structures by means of experimental methods. This disadvantage can be solved by means of computational analysis which allows to determine the whole stress and strain fields in complex structures. In this paper the temperature distribution and residual stresses were determined in a single-pass butt joint welded by GMAW (Gas Metal Arc Welding) process by finite element model (FEM). A 3D finite parametric element model has been carried out to analyze temperature distribution in butt weld joints and thermo-mechanical analyses were performed to evaluate resulting residual stresses. Temperature fields have been investigated by varying an initial preheating treatment. Moreover the technique of “element birth and death” was adopted to simulate the process of filler metal addition The high stresses were evaluated, with particular regard to fusion zone and heat affected zone. The influence of preheating and post-heating treatment on residual stresses was investigated. The residual stresses decrease when preheating temperature increases. The maximum value of longitudinal residual stresses without pre-heating can be reduced about 12% and 38% by using the preheating and post-heating process respectively.

scholarly journals Analysis of temperature-induced deformation and stress distribution of long-span concrete truss combination arch bridge based on bridge health monitoring data and finite element simulation

2020 ◽  
Vol 16 (10) ◽  
pp. 155014772094520
Author(s):  
Yanwei Niu ◽  
Yong’e Wang ◽  
Yingying Tang
Keyword(s):  
Finite Element ◽  
Temperature Distribution ◽  
Stress Distribution ◽  
Health Monitoring ◽  
Three Dimensional ◽  
Monitoring Data ◽  
Temperature Fields ◽  
Structural Deformation ◽  
Arch Bridge ◽  
Bridge Health Monitoring

Through decades of operation, deformation fluctuation becomes a central problem affecting the normal operating of concrete truss combination arch bridge. In order to clarify the mechanism of temperature-induced deformation and its impact on structural stress distribution, this article reports on the temperature distribution and its effect on the deformation of concrete truss combination arch bridge based on bridge health monitoring on a proto bridge with 138 m main span. The temperature distribution and deformation characteristics of the bridge structure in deep valley area are studied. Both of the daily and yearly temperature variation and structural deformation are studied based on bridge health monitoring. Using the outcome of monitoring data, three-dimensional solid finite element models are established to analyze the mechanism of temperature-induced deformation of the whole bridge under different temperature fields. The influence of temperature-induced effect is discussed on local damage based on the damage observation of the background bridge. The outcome of comparisons with field observation validates the analysis results. The relevant monitoring and simulation result can be referenced for the design and evaluation of similar bridges.

Axial Transport Effects on Natural Convection Inside of an Open-Ended Annulus

1991 ◽  
Vol 113 (3) ◽  
pp. 627-634 ◽  
Author(s):  
K. Vafai ◽  
J. Ettefagh
Keyword(s):  
Temperature Distribution ◽  
Flow Field ◽  
Three Dimensional ◽  
Transient Behavior ◽  
Temperature Fields ◽  
Two Dimensional ◽  
Three Dimensional Flow ◽  
Subsequent Effect ◽  
Transport Effects ◽  
Temperature And Velocity Fields

The present work centers around a numerical three-dimensional transient investigation of the effects of axial convection on flow and temperature fields inside an open-ended annulus. The transient behavior of the flow field through the formation of a three-dimensional flow field and its subsequent effect on the temperature distribution at different axial locations within the annulus were analyzed by both finite difference and finite element methods. The results show that the axial convection has a distinctly different influence on the temperature and velocity fields. It is found that in the midportion of the annulus a two-dimensional assumption with respect to the temperature distribution can lead to satisfactory results for Ra<10,000. However, such an assumption is improper with respect to the flow field. Furthermore, it is shown that generally the errors for a two-dimensional assumption in the midportion of the annulus are less at earlier times (t<50Δt) during the transient development of the flow and temperature fields.

Optical Monitoring and Numerical Simulation of Temperature Distribution at Selective Laser Melting of Ti6Al4V Alloy

2015 ◽  
Vol 828-829 ◽  
pp. 474-481 ◽  
Author(s):  
Ivan Zhirnov ◽  
Ina Yadroitsava ◽  
Igor Yadroitsev
Keyword(s):  
Numerical Simulation ◽  
Temperature Distribution ◽  
Selective Laser Melting ◽  
Ti6al4v Alloy ◽  
Advanced Technology ◽  
Temperature Fields ◽  
Optical Monitoring ◽  
Metal Powders ◽  
Laser Melting ◽  
Ir Camera

Selective laser melting (SLM) is a modern method for producing objects with complex shape and fine structures in one working cycle from metal powders. Combination of the advanced technology of SLM with unique properties of Ti6Al4V alloy allows creating complex 3D objects for medicine or aerospace industry. Since properties of SLM parts depend on the geometrical characteristics of tracks and their cohesion, optical monitoring is actually used to for control the process. Temperature gradient determines the microstructure and mechanical properties of the SLM part, so studies about temperature fields are primarily important. On-line monitoring during laser scanning of Ti6Al4V alloy and formation of a single track in real-time with high-speed IR camera was studied. Numerical simulation allowed estimation the temperature distribution during processing. Conclusion regarding control system based on the online monitoring of deviations of the signal from IR camera during the SLM process was done.

scholarly journals An Experimental Investigation of the External Wind Effects on the Ceiling Temperature Distribution of Fire-Induced Thermal Flow in a Corridor Connected to a Compartment

Energies ◽  
2020 ◽  
Vol 13 (7) ◽  
pp. 1826
Author(s):  
Bei Cao ◽  
Xiaodong Zhou ◽  
Yubiao Huang ◽  
Yuan Zheng ◽  
Kai Ye ◽  
...  
Keyword(s):  
Experimental Investigation ◽  
Temperature Distribution ◽  
Wind Velocity ◽  
Shielding Effect ◽  
Temperature Profiles ◽  
Building Structures ◽  
Thermal Flow ◽  
Ceiling Temperature ◽  
Higher Temperature

Fire-induced thermal flow is the greatest threat to trapped people and the heat-resistant quality of building structures. This paper presents an experimental investigation of the effects of external wind on the ceiling temperature distribution of fire-induced thermal flow in a one-sixth scale corridor connected to a compartment. In the experiments, the fire source was placed in the compartment with hot thermal flow spilled into the connected corridor. The heat release rate (HRR) was changed from 10 to 20 kW and the external wind velocity was changed from 0 to 2.09 m/s. The ends of the corridor could be adjusted to be fully or partially open to the environment with dam-boards arranged at the ends of the corridor. An effective corridor HRR, Qcorridor, was defined to account for the amount of the spilled plume into the corridor. Results show that the temperature under the ceiling changed in a non-monotonic way with wind velocity: it first increased and then decreased with wind velocity. It was revealed that the dam-boards at the corridor opening had an evidently shielding effect, leading to higher temperature compared to the fully open environment. Finally, uniform correlations are proposed for predicting the attenuation law of ceiling temperature profiles in corridors for different wind conditions.

Sign in / Sign up

Export Citation Format

Share Document