Study of Temperature Effect on Servovalve-Controlled Fuel Metering Unit

2015 ◽  
Vol 137 (6) ◽  
Author(s):  
Bin Wang ◽  
Haocen Zhao ◽  
Ling Yu ◽  
Zhifeng Ye
Keyword(s):  
Steady State ◽  
Temperature Variation ◽  
Dynamic Characteristics ◽  
Numerical Study ◽  
Step Response ◽  
Fuel Temperature ◽  
Wide Range ◽  
Fuel Rate ◽  
Testing Condition ◽  
The Given

It is usual that fuel system of an aero-engine operates within a wide range of temperatures. As a result, this can have effect on both the characteristics and precision of fuel metering unit (FMU), even on the performance and safety of the whole engine. This paper provides theoretical analysis of the effect that fluctuation of fuel temperature has on the controllability of FMU and clarifies the drawbacks of the pure mathematical models considering fuel temperature variation for FMU. Taking the electrohydraulic servovalve-controlled FMU as the numerical study, simulation in AMESim is carried out by thermal hydraulic model under the temperatures ranged from −10 to 60 °C to confirm the effectiveness and precision of the model on the basis of steady-state and dynamic characteristics of FMU. Meanwhile, the FMU testing workbench with temperature adjustment device employing the fuel cooler and heater is established to conduct an experiment of the fuel temperature characteristics. Results show that the experiment matches well with the simulation with a relative error no more than 5% and that 0–50 °C fuel temperature variation produces up to 5.2% decrease in fuel rate. In addition, step response increases with the fuel temperature. Fuel temperature has no virtual impact on the steady-state and dynamic characteristics of FMU under the testing condition in this paper, implying that FMU can operate normally in the given temperature range.

Experimental and Numerical Study of Steady and Modulated Transverse Jets at Low Blowing Ratios

2010 ◽  
Author(s):  
Guillaume Bidan ◽  
Pierre-Emmanuel Bouladoux ◽  
Jeremiah E. Oertling ◽  
Dimitris E. Nikitopoulos
Keyword(s):  
Steady State ◽  
Numerical Study ◽  
Mie Scattering ◽  
Formation Mechanisms ◽  
Transitional Region ◽  
Vortical Structures ◽  
Coverage Metrics ◽  
Jet In Crossflow ◽  
Wide Range ◽  
Hotwire Anemometry

The effects of jet flow pulsation were investigated in the case of a fully modulated vertical jet in crossflow over a flat plate using Mie scattering visualizations, hotwire anemometry and Large Eddy Simulations (LES). A preliminary steady state study was conducted over a wide range of blowing ratios to provide a baseline comparison to pulsed results in terms of vortical structures and performance. Based on observation of the vortical structures and hotwire signatures, two distinct regimes were identified separated by a transitional region. LES using the dynamic Smagorinsky sub-grid model were carried out to provide additional insights on vortical structures formation mechanisms and their effect on heat transfer results, showing good agreement with the experimental observations and measurements. The influence of the pulsing parameters such as mean, high and low blowing ratios, forcing frequency and duty cycle was explored in terms of jet coverage metrics and spanwise adiabatic effectiveness. Average blowing ratios of 0.250, 0.350 and 0.450, duty cycles of 25, 50 and 70% and forcing frequencies of St∞ = 0.008, 0.016, 0.079, and 0.159 were investigated. While in most of the cases, forced jets show a decrease in average performance compared to steady state configurations, some improvement was found in part of the forcing cycle. Vortical structures formed at the jet onset are consistent with the classification given by previous studies in terms of stroke-ratio and high blowing ratio over an overlapping range of conditions. The dynamics of the vortical structures formed at the pulse rise are highly responsible for the decrease in performance observed under forced conditions.

Effect of Solid Subcooling on Natural Convection Melting of a Pure Metal

1989 ◽  
Vol 111 (2) ◽  
pp. 416-424 ◽  
Author(s):  
C. Beckermann ◽  
R. Viskanta
Keyword(s):  
Heat Transfer ◽  
Steady State ◽  
Natural Convection ◽  
Numerical Study ◽  
Pure Metal ◽  
Liquid Region ◽  
Cold Wall ◽  
Fusion Temperature ◽  
Local Flow ◽  
Wide Range

A combined experimental and numerical study is reported of melting of a pure metal inside a vertical rectangular enclosure with natural convection in the liquid and conduction in the solid. The numerical model is successfully verified by conducting a series of experiments covering a wide range of hot and cold wall temperatures. It is found that solid subcooling significantly reduces the melting rate when compared to melting with the solid at the fusion temperature. Because the cooled wall is held below the fusion temperature of the metal, the solid/liquid interface eventually reaches a stationary position. For moderate values of the subcooling parameter the steady-state interface is almost vertical and parallel to the cold wall. Strong subcooling results in an early termination of the melting process, such that natural convection in the relatively small liquid region cannot fully develop. For moderate subcooling, correlations have been derived for the steady-state volume and heat transfer rates. While many aspects of melting with solid subcooling appear to be similar to ordinary nonmetallic solids, important differences in the local flow structures and heat transfer mechanisms are observed.

An Investigation of the Effect of interrupted fin arrangements on the Thermal Performance of a Heat Sink under a Free Convection Condition

2019 ◽  
Vol 7 (1) ◽  
pp. 43-53
Author(s):  
Abbas Jassem Jubear ◽  
Ali Hameed Abd
Keyword(s):  
Heat Transfer ◽  
Steady State ◽  
Natural Convection ◽  
Thermal Performance ◽  
Heat Sink ◽  
Numerical Study ◽  
Ansys Fluent ◽  
Fluent Software ◽  
Steady State Heat ◽  
Steady State Heat Transfer

The heat sink with vertically rectangular interrupted fins was investigated numerically in a natural convection field, with steady-state heat transfer. A numerical study has been conducted using ANSYS Fluent software (R16.1) in order to develop a 3-D numerical model.  The dimensions of the fins are (305 mm length, 100 mm width, 17 mm height, and 9.5 mm space between fins. The number of fins used on the surface is eight. In this study, the heat input was used as follows: 20, 40, 60, 80, 100, and 120 watts. This study focused on interrupted rectangular fins with a different arrangement and angle of the fins. Results show that the addition of interruption in fins in various arrangements will improve the thermal performance of the heat sink, and through the results, a better interruption rate as an equation can be obtained.

Effect of Viscous Dissipation on MHD Williamson Nanofluid Flow in a Porous Medium

2019 ◽  
Vol 8 (3) ◽  
pp. 5795-5802 ◽  
Keyword(s):  
Porous Medium ◽  
Steady State ◽  
Numerical Solution ◽  
Viscous Dissipation ◽  
Flow Problem ◽  
Numerical Study ◽  
Steady State Flow ◽  
Nanofluid Flow ◽  
Shooting Technique ◽  
Order Four

The main objective of this paper is to focus on a numerical study of viscous dissipation effect on the steady state flow of MHD Williamson nanofluid. A mathematical modeled which resembles the physical flow problem has been developed. By using an appropriate transformation, we converted the system of dimensional PDEs (nonlinear) into coupled dimensionless ODEs. The numerical solution of these modeled ordinary differential equations (ODEs) is achieved by utilizing shooting technique together with Adams-Bashforth Moulton method of order four. Finally, the results of discussed for different parameters through graphs and tables.

Spectroscopic Studies of Asparaginyl-tRNA Synthetase from Entamoeba histolytica

2019 ◽  
Vol 26 (6) ◽  
pp. 435-448
Author(s):  
Priyanka Biswas ◽  
Dillip K. Sahu ◽  
Kalyanasis Sahu ◽  
Rajat Banerjee
Keyword(s):  
Circular Dichroism ◽  
Steady State ◽  
Entamoeba Histolytica ◽  
Protein Concentration ◽  
Trna Synthetase ◽  
Solvent Exposure ◽  
Steady State Fluorescence ◽  
State Process ◽  
Wide Range ◽  
Circular Dichroïsm

Background: Aminoacyl-tRNA synthetases play an important role in catalyzing the first step in protein synthesis by attaching the appropriate amino acid to its cognate tRNA which then transported to the growing polypeptide chain. Asparaginyl-tRNA Synthetase (AsnRS) from Brugia malayi, Leishmania major, Thermus thermophilus, Trypanosoma brucei have been shown to play an important role in survival and pathogenesis. Entamoeba histolytica (Ehis) is an anaerobic eukaryotic pathogen that infects the large intestines of humans. It is a major cause of dysentery and has the potential to cause life-threatening abscesses in the liver and other organs making it the second leading cause of parasitic death after malaria. Ehis-AsnRS has not been studied in detail, except the crystal structure determined at 3 Å resolution showing that it is primarily α-helical and dimeric. It is a homodimer, with each 52 kDa monomer consisting of 451 amino acids. It has a relatively short N-terminal as compared to its human and yeast counterparts. Objective: Our study focusses to understand certain structural characteristics of Ehis-AsnRS using biophysical tools to decipher the thermodynamics of unfolding and its binding properties. Methods: Ehis-AsnRS was cloned and expressed in E. coli BL21DE3 cells. Protein purification was performed using Ni-NTA affinity chromatography, following which the protein was used for biophysical studies. Various techniques such as steady-state fluorescence, quenching, circular dichroism, differential scanning fluorimetry, isothermal calorimetry and fluorescence lifetime studies were employed for the conformational characterization of Ehis-AsnRS. Protein concentration for far-UV and near-UV circular dichroism experiments was 8 µM and 20 µM respectively, while 4 µM protein was used for the rest of the experiments. Results: The present study revealed that Ehis-AsnRS undergoes unfolding when subjected to increasing concentration of GdnHCl and the process is reversible. With increasing temperature, it retains its structural compactness up to 45ºC before it unfolds. Steady-state fluorescence, circular dichroism and hydrophobic dye binding experiments cumulatively suggest that Ehis-AsnRS undergoes a two-state transition during unfolding. Shifting of the transition mid-point with increasing protein concentration further illustrate that dissociation and unfolding processes are coupled indicating the absence of any detectable folded monomer. Conclusion: This article indicates that GdnHCl induced denaturation of Ehis-AsnRS is a two – state process and does not involve any intermediate; unfolding occurs directly from native dimer to unfolded monomer. The solvent exposure of the tryptophan residues is biphasic, indicating selective quenching. Ehis-AsnRS also exhibits a structural as well as functional stability over a wide range of pH.

scholarly journals Effects of Precast Cladding Systems on Dynamic Characteristics of Steel Frame Buildings by Ambient and Free Vibration Tests

2017 ◽  
Vol 2017 ◽  
pp. 1-20 ◽  
Author(s):  
Jun Ma ◽  
Shinji Nakata ◽  
Akihito Yoshida ◽  
Yukio Tamura
Keyword(s):  
Free Vibration ◽  
Dynamic Characteristics ◽  
Steel Frame ◽  
Ambient Vibration ◽  
Test Cases ◽  
Vibration Method ◽  
External Wall ◽  
Wide Range ◽  
Cladding Panels ◽  
Vibration Tests

Full-scale tests on a one-story steel frame structure with a typical precast cladding system using ambient and free vibration methods are described in detail. The cladding system is primarily composed of ALC (Autoclaved Lightweight Concrete) external wall cladding panels, gypsum plasterboard interior linings, and window glazing systems. Ten test cases including the bare steel frame and the steel frame with addition of different parts of the precast cladding system are prepared for detailed investigations. The amplitude-dependent dynamic characteristics of the test cases including natural frequencies and damping ratios determined from the tests are presented. The effects of the ALC external wall cladding panels, the gypsum plasterboard interior linings, and the window glazing systems on the stiffness and structural damping of the steel frame are discussed in detail. The effect of the precast cladding systems on the amplitude dependency of the dynamic characteristics and the tendencies of the dynamic parameters with respect to the structural response amplitude are investigated over a wide range. Furthermore, results estimated from the ambient vibration method are compared with those from the free vibration tests to evaluate the feasibility of the ambient vibration method.

scholarly journals Strain Sensor via Wood Anomalies in 2D Dielectric Array

Nanomaterials ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 1022
Author(s):  
Rashid G. Bikbaev ◽  
Ivan V. Timofeev ◽  
Vasiliy F. Shabanov
Keyword(s):  
Higher Plants ◽  
Numerical Study ◽  
Reciprocal Lattice ◽  
Strain Sensing ◽  
Photonic Materials ◽  
Sensing Applications ◽  
Wide Range ◽  
Sensor Structure ◽  
Optical Behavior ◽  
Chlorophyll Absorption

Optical sensing is one of many promising applications for all-dielectric photonic materials. Herein, we present an analytical and numerical study on the strain-responsive spectral properties of a bioinspired sensor. The sensor structure contains a two-dimensional periodic array of dielectric nanodisks to mimic the optical behavior of grana lamellae inside chloroplasts. To accumulate a noticeable response, we exploit the collective optical mode in grana ensemble. In higher plants, such a mode appears as Wood’s anomaly near the chlorophyll absorption line to control the photosynthesis rate. The resonance is shown persistent against moderate biological disorder and deformation. Under the stretching or compression of a symmetric structure, the mode splits into a couple of polarized modes. The frequency difference is accurately detected. It depends on the stretch coefficient almost linearly providing easy calibration of the strain-sensing device. The sensitivity of the considered structure remains at 5 nm/% in a wide range of strain. The influence of the stretching coefficient on the length of the reciprocal lattice vectors, as well as on the angle between them, is taken into account. This adaptive phenomenon is suggested for sensing applications in biomimetic optical nanomaterials.

Numerical study of geometric morphing wings of the 1303 UCAV

2021 ◽  
pp. 1-17
Author(s):  
B. Nugroho ◽  
J. Brett ◽  
B.T. Bleckly ◽  
R.C. Chin
Keyword(s):  
Flight Control ◽  
Numerical Study ◽  
Aerodynamic Characteristics ◽  
Morphing Wing ◽  
Rolling Moment ◽  
Wide Range ◽  
Morphing Wings ◽  
Wing Geometry ◽  
Lift And Drag ◽  
Wing Morphing

ABSTRACT Unmanned Combat Aerial Vehicles (UCAVs) are believed by many to be the future of aerial strike/reconnaissance capability. This belief led to the design of the UCAV 1303 by Boeing Phantom Works and the US Airforce Lab in the late 1990s. Because UCAV 1303 is expected to take on a wide range of mission roles that are risky for human pilots, it needs to be highly adaptable. Geometric morphing can provide such adaptability and allow the UCAV 1303 to optimise its physical feature mid-flight to increase the lift-to-drag ratio, manoeuvrability, cruise distance, flight control, etc. This capability is extremely beneficial since it will enable the UCAV to reconcile conflicting mission requirements (e.g. loiter and dash within the same mission). In this study, we conduct several modifications to the wing geometry of UCAV 1303 via Computational Fluid Dynamics (CFD) to analyse its aerodynamic characteristics produced by a range of different wing geometric morphs. Here we look into two specific geometric morphing wings: linear twists on one of the wings and linear twists at both wings (wash-in and washout). A baseline CFD of the UCAV 1303 without any wing morphing is validated against published wind tunnel data, before proceeding to simulate morphing wing configurations. The results show that geometric morphing wing influences the UCAV-1303 aerodynamic characteristics significantly, improving the coefficient of lift and drag, pitching moment and rolling moment.

scholarly journals A Computational Study on the Role of Parameters for Identification of Thyroid Nodules by Infrared Images (and Comparison with Real Data)

Sensors ◽  
2021 ◽  
Vol 21 (13) ◽  
pp. 4459
Author(s):  
José R. González ◽  
Charbel Damião ◽  
Maira Moran ◽  
Cristina A. Pantaleão ◽  
Rubens A. Cruz ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Thyroid Nodules ◽  
Numerical Study ◽  
Computational Study ◽  
Internal Heat ◽  
Heat Transfer Process ◽  
The Body ◽  
Physical Parameters ◽  
Infrared Sensors ◽  
Wide Range

According to experts and medical literature, healthy thyroids and thyroids containing benign nodules tend to be less inflamed and less active than those with malignant nodules. It seems to be a consensus that malignant nodules have more blood veins and more blood circulation. This may be related to the maintenance of the nodule’s heat at a higher level compared with neighboring tissues. If the internal heat modifies the skin radiation, then it could be detected by infrared sensors. The goal of this work is the investigation of the factors that allow this detection, and the possible relation with any pattern referent to nodule malignancy. We aim to consider a wide range of factors, so a great number of numerical simulations of the heat transfer in the region under analysis, based on the Finite Element method, are performed to study the influence of each nodule and patient characteristics on the infrared sensor acquisition. To do so, the protocol for infrared thyroid examination used in our university’s hospital is simulated in the numerical study. This protocol presents two phases. In the first one, the body under observation is in steady state. In the second one, it is submitted to thermal stress (transient state). Both are simulated in order to verify if it is possible (by infrared sensors) to identify different behavior referent to malignant nodules. Moreover, when the simulation indicates possible important aspects, patients with and without similar characteristics are examined to confirm such influences. The results show that the tissues between skin and thyroid, as well as the nodule size, have an influence on superficial temperatures. Other thermal parameters of thyroid nodules show little influence on surface infrared emissions, for instance, those related to the vascularization of the nodule. All details of the physical parameters used in the simulations, characteristics of the real nodules and thermal examinations are publicly available, allowing these simulations to be compared with other types of heat transfer solutions and infrared examination protocols. Among the main contributions of this work, we highlight the simulation of the possible range of parameters, and definition of the simulation approach for mapping the used infrared protocol, promoting the investigation of a possible relation between the heat transfer process and the data obtained by infrared acquisitions.

scholarly journals Identification of DC Thermal Steady-State Differential Inductance of Ferrite Power Inductors

Energies ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3854
Author(s):  
Salvatore Musumeci ◽  
Luigi Solimene ◽  
Carlo Stefano Ragusa
Keyword(s):  
Steady State ◽  
Input Voltage ◽  
Switching Frequency ◽  
Ohmic Losses ◽  
Steady State Temperature ◽  
Wide Range ◽  
Average Current ◽  
Power Inductors ◽  
Saturable Inductor ◽  
Thermal Steady State

In this paper, we propose a method for the identification of the differential inductance of saturable ferrite inductors adopted in DC–DC converters, considering the influence of the operating temperature. The inductor temperature rise is caused mainly by its losses, neglecting the heating contribution by the other components forming the converter layout. When the ohmic losses caused by the average current represent the principal portion of the inductor power losses, the steady-state temperature of the component can be related to the average current value. Under this assumption, usual for saturable inductors in DC–DC converters, the presented experimental setup and characterization method allow identifying a DC thermal steady-state differential inductance profile of a ferrite inductor. The curve is obtained from experimental measurements of the inductor voltage and current waveforms, at different average current values, that lead the component to operate from the linear region of the magnetization curve up to the saturation. The obtained inductance profile can be adopted to simulate the current waveform of a saturable inductor in a DC–DC converter, providing accurate results under a wide range of switching frequency, input voltage, duty cycle, and output current values.

Sign in / Sign up

Export Citation Format

Share Document