Numerical Investigation of Regular and Hybrid Nanofluids Application as the Working Fluids on Thermal Performance of TPCT

2019 ◽  
Vol 11 (4) ◽  
Author(s):  
Roozbeh Vadi ◽  
Kamran Sepanloo
Keyword(s):  
Numerical Simulation ◽  
Thermal Resistance ◽  
Natural Circulation ◽  
Industrial Applications ◽  
Input Power ◽  
Working Fluid ◽  
Hybrid Nanofluid ◽  
Distilled Water ◽  
Two Phase ◽  
Working Fluids

Two-phase closed thermosyphon (TPCT) is a cost-effective heat transfer device with high thermal efficiency owing to extensive interphase heat and mass transfer. Thus, TPCT has found many industrial applications. Proper selection of the working fluid could further improve efficiency of TPCT, and nanofluids with superior thermal properties are suitable choices. Numerical simulation of boiling and condensation, natural circulation, and hybrid nanofluid modeling in a closed space is a notable challenge and current study is devoted to this subject. In this study, a novel methodology for incorporating the effects of compressibility and thermal expansion into all thermophysical properties of both phases is developed and programmed into a validated computational fluid dynamics (CFD) code. Distilled water, a regular nanofluid, Al2O3/water, and a hybrid nanofluid, TiSiO4/water are selected as the working fluids. Experimental data for wall thermal profile are employed to validate the numerical simulation. Then, overall thermal resistance is evaluated in terms of nanoparticles concentration and input power variations. Results indicate that the numerical methodology developed in this study could evaluate the optimum state of TPCT in an efficient and accurate manner and the optimum state for regular and hybrid nanofluid demonstrates 48% and 54% improvement over distilled water, respectively. Furthermore, a subtle relation between the thermal resistance and the height to which fluid column rises in TPCT has been discerned and quantified, which is used as a supplement to the conventional qualitative method of reasoning to justify the somewhat controversial behaviors of nanofluid application in TPCT.

scholarly journals Experimental Investigation of the Thermal Performance of a Wickless Heat Pipe Operating with Different Fluids: Water, Ethanol, and SES36. Analysis of Influences of Instability Processes at Working Operation Parameters

Energies ◽  
2018 ◽  
Vol 12 (1) ◽  
pp. 80 ◽  
Author(s):  
Rafal Andrzejczyk
Keyword(s):  
Heat Pipe ◽  
Input Power ◽  
Liquid Pool ◽  
Filling Ratio ◽  
Working Fluid ◽  
Operating Pressure ◽  
Two Phase ◽  
Condenser Section ◽  
Transfer Resistance ◽  
Working Fluids

In this study, the influences of different parameters on performance of a wickless heat pipe have been presented. Experiments have been carried out for an input power range from 50 W to 300 W, constant cooling water mass flow rate of 0.01 kg/s, and constant temperature at the inlet to condenser of 10 °C. Three working fluids have been tested: water, ethanol, and SES36 (1,1,1,3,3-Pentafluorobutane) with different filling ratios (0.32, 0.51, 1.0). The wall temperature in different locations (evaporation section, adiabatic section, and condenser section), as well as operating pressure inside two phase closed thermosyphon have been monitored. The wickless heat pipe was made of 0.01 m diameter copper tube, which consists of an evaporator, adiabatic, and condensation sections with the same length (0.4 m). For all working fluids, a dynamic start-up effect caused by heat conduction towards the liquid pool was observed. Only the thermosyphon filled with SES36 was observed to have operation limitation caused by achieving the boiling limit in TPCTs (two-phase closed thermosyphons). The geyser boiling effect has been observed only for thermosyphon filled with ethanol and for a high filling ratio. The performance of the thermosyphon determined the form of the heat transfer resistance of the TPCT and it was found to be dependent of input power and filling ratio, as well as the type of working fluid and AR (aspect ratio). Comparison with other authors would seem to indicate that lower AR results in higher resistance; however, the ratio of condenser section length to inside diameter of pipe is also a very important parameter. Generally, performance of the presented thermosyphon is comparable to other constructions.

scholarly journals Experimental Investigation of Thermosyphon Thermal Performance Using Different Filling Ratio

2021 ◽  
Vol 39 (1A) ◽  
pp. 34-44
Author(s):  
Talib Z. Farge ◽  
Samar J. Ismael ◽  
Rawad M. Thyab
Keyword(s):  
Experimental Investigation ◽  
Thermal Resistance ◽  
Thermal Performance ◽  
Heat Dissipation ◽  
Operating Temperature ◽  
Input Power ◽  
Filling Ratio ◽  
Working Fluid ◽  
Distilled Water ◽  
Percentage Decrease

The present work investigated the thermal performance of thermosyphon by using distilled water as a working fluid at different filling ratios (50%, 60%, and 70 %). The thermosyphon was manufactured from a copper tube with outer and inner diameters (26 and 24) mm, respectively. The thermosyphon was tested experimentally at different input power (100, 200 and 300) Watt. The operating temperature of the oil was chosen below 85°C. Experimental results revealed that the filling ratio of 60% exhibited the best heat dissipation at the highest operating temperature. While the low operating temperature and 50 % filling ratio show better heat dissipation. Further, it was found that the thermal resistance of the thermosyphon was obviously decreased with increasing the input power. The percentage decrease in the thermal resistance of the thermosyphon at a filling ratio of 0.6 was 14.6 % compared with that filling ratio of 0.5 at an input power of 300 W.

scholarly journals Heat Transfer Enhancement of Small-Diameter Two-Phase Closed Thermosyphon Using Cellulose Nanofiber and Hydrophilic Surface Modification

Nanomaterials ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 647
Author(s):  
Dongnyeok Choi ◽  
Gyosik Jun ◽  
Woonbong Hwang ◽  
Kwon-Yeong Lee
Keyword(s):  
Surface Modification ◽  
Thermal Resistance ◽  
Natural Circulation ◽  
Small Diameter ◽  
Cellulose Nanofiber ◽  
Working Fluid ◽  
Hydrophilic Surface ◽  
Two Phase ◽  
Total Thermal Resistance ◽  
Internal Working

In this study, we observed the Geyser phenomenon that occurs in a small-diameter two-phase closed thermosyphon (confinement number of 0.245). This phenomenon interferes with the natural circulation of the internal working fluid and increases the thermal resistance of the system. This study attempts to improve the thermal performance of the system using cellulose nanofiber as the working fluid and hydrophilic surface modification at the inner surface of the evaporator section. As a result, the total thermal resistance showed average reduction rates of 47.51%, 36.69%, and 22.56% at filling ratios of 0.25, 0.5, and 0.75, respectively.

Converting Low-Grade Heat Into Power Using a Supercritical Rankine Cycle With Zeotropic Mixture Working Fluid

2010 ◽  
Author(s):  
Huijuan Chen ◽  
D. Yogi Goswami ◽  
Muhammad M. Rahman ◽  
Elias K. Stefanakos
Keyword(s):  
Rankine Cycle ◽  
Phase Region ◽  
Working Fluid ◽  
Condensation Process ◽  
Heating Process ◽  
Low Grade ◽  
Two Phase ◽  
Working Fluids ◽  
Zeotropic Mixture ◽  
Low Grade Heat

A supercritical Rankine cycle using zeotropic mixture working fluids for the conversion of low-grade heat into power is proposed and analyzed in this paper. A supercritical Rankine cycle does not go through two-phase region during the heating process. By adopting zeotropic mixtures as the working fluids, the condensation process happens non-isothermally. Both of the features create a potential in reducing the irreversibility and improving the system efficiency. A comparative study between an organic Rankine cycle and the proposed supercritical Rankine cycle shows that the proposed cycle improves the cycle thermal efficiency, exergy efficiency of the heating and the condensation processes, and the system overall efficiency.

Heat Transport Characteristics in Closed Loop Oscillating Heat Pipes

2005 ◽  
Author(s):  
Shuangfeng Wang ◽  
Shigefumi Nishio
Keyword(s):  
Heat Pipe ◽  
Heat Transport ◽  
Closed Loop ◽  
Flow Behavior ◽  
Working Fluid ◽  
Liquid Volume ◽  
High Heat Flux ◽  
Two Phase ◽  
Working Fluids ◽  
Inner Diameter

Heat transport rates of micro scale SEMOS (Self-Exciting Mode Oscillating) heat pipe with inner diameter of 1.5mm, 1.2mm and 0.9mm, were investigated by using R141b, ethanol and water as working fluids. The effects of inner diameter, liquid volume faction, and material properties of the working fluids are examined. It shows that the smaller the inner diameter, the higher the thermal transport density is. For removing high heat flux, the water is the most promising working fluid as it has the largest critical heat transfer rate and the widest operating range among the three kinds of working fluids. A one-dimensional numerical simulation is carried out to describe the heat transport characteristics and the two-phase flow behavior in the closed loop SEMOS heat pipe. The numerical prediction agrees with the experimental results fairly well, when the input heat through was not very high and the flow pattern was slug flow.   This paper was also originally published as part of the Proceedings of the ASME 2005 Pacific Rim Technical Conference and Exhibition on Integration and Packaging of MEMS, NEMS, and Electronic Systems.

Fluid Flow and Boiling Heat Transfer in Mini Channels

2010 ◽  
Author(s):  
M. Venkatesan ◽  
M. Aravinthan ◽  
Sarit K. Das ◽  
A. R. Balakrishnan
Keyword(s):  
Heat Transfer ◽  
Fluid Flow ◽  
Boiling Heat Transfer ◽  
Industrial Applications ◽  
Tube Diameter ◽  
Working Fluid ◽  
Phase Flow ◽  
Two Phase ◽  
Mini Channels ◽  
Micro Propulsion

Two phase flows in mini channels occur in many industrial applications such as electronic cooling, compact heat exchangers, compact refrigeration systems and in micro propulsion devices. Due to its significance, research on two phase flow in mini channels has become attractive. However, in recent times a controversy exists whether flow in minichannel is different from macro flow because there are still substantial disagreements among various experimental results. In the present study an experimental investigation is carried out for fluid flow and boiling heat transfer characteristics of mini channels with tube diameters ranging from 1–3mm. The tubes were made of SS with water as the working fluid. The variation in friction factor and Nusselt number with decrease in tube diameter for single phase flow was systematically studied. The point of Onset of Nucelate Boiling (ONB) was identified based on wall temperature profile. The effect of heat flux and mass flux on two phase pressure drop with three different tube diameters during sub cooled boiling were investigated. The results reveal that there is an unmistakable effect of tube diameter on fluid friction and onset of boiling during sub cooled boiling in tubes of mini channel dimensions.

A Comprehensive Experimental Investigation of the Performance of Closed-Loop Pulsating Heat Pipes

2017 ◽  
Vol 139 (9) ◽  
Author(s):  
M. Halimi ◽  
A. Abbas Nejad ◽  
M. Norouzi
Keyword(s):  
Thermal Resistance ◽  
Flow Regime ◽  
Thermal Performance ◽  
Closed Loop ◽  
Heat Pipes ◽  
Filling Ratio ◽  
Working Fluid ◽  
Physical Parameters ◽  
Two Phase ◽  
Laboratory Conditions

Closed-loop pulsating heat pipes (CLPHPs) are a new type of two-phase heat transfer devices that can transfer considerable heat in a small space via two-phase vapor and liquid pulsating flow and work with various types of two-phase instabilities so the operating mechanism of CLPHP is not well understood. In this work, two CLPHPs, made of Pyrex, were manufactured to observe and investigate the flow regime that occurs during the operation of CLPHP and thermal performance of the device under different laboratory conditions. In general, various working fluids were used in filling ratios of 40%, 50%, and 60% in horizontal and vertical modes to investigate the effect of thermo-physical parameters, filling ratio, nanoparticles, gravity, CLPHP structure, and input heat flux on the thermal performance of CLPHP. The results indicate that three types of flow regime may be observed given laboratory conditions. Each flow regime exerts a different effect on the thermal performance of the device. There is an optimal filling ratio for each working fluid. The increased number of turns in CLPHP generally improves the thermal performance of the system reducing the effect of the type of the working fluid on the aforementioned performance. The adoption of copper nanoparticles, which positively affect fluid motion, decreases the thermal resistance of the system as much as 6.06–42.76% depending on laboratory conditions. Moreover, gravity brings about positive changes in the flow regime decreasing thermal resistance as much as 32.13–52.58%.

scholarly journals Experimental Set up of Two Closed Loop Pulsating Heat Pipe (CLPHP) with Water base Fluids

2019 ◽  
Vol 8 (12S) ◽  
pp. 715-719
Keyword(s):  
Thermal Resistance ◽  
Heat Pipe ◽  
Heat Dissipation ◽  
Heat Pipes ◽  
Heat Fluxes ◽  
Working Fluid ◽  
Water Mixture ◽  
Working Fluids ◽  
Pure Fluids ◽  
Acetone Water

Heat pipes are deliberated to be effective heat dissipation devices compared to other types of heat sinks due to their high effective thermal conductivity. Because of the flexibility in the design and layout of heat pipe turns along the heat source, pulsating heat pipes have gained popularity. One of the parameters that have the mainimpact on the presentation of CLPHP is the thermo physical properties of the working fluid. The properties of the working fluid affect the temperature difference between the evaporator and the condenser which in turn affect the thermal resistance of the CLPHP. In this connection, the influence of different working fluids is experimentally investigated on a two loop CLPHP, varying the evaporator heat flux. Pure fluids, viz., water, acetone, benzene and binary mixture, viz., Acetone-water and Benzene-water are utilized on working fluids. The heat input considered at the evaporator is 32W, 48W and 60W. The filling ratio is kept as 50 %. The results show that among the working fluids considered for the study, acetone exhibits least thermal resistance among the pure fluids at all heat fluxes considered in the analysis, while Acetone-water mixture has exhibited least thermal resistance among the water based mixtures.

Thermal Characteristics of a Circular Finned Thermosyphon Using Different Working Fluids

2014 ◽  
Vol 575 ◽  
pp. 322-328 ◽  
Author(s):  
Narayanan Alagappan ◽  
Narayanan Karunakaran
Keyword(s):  
Experimental Study ◽  
Ethylene Glycol ◽  
Thermal Resistance ◽  
Thermal Performance ◽  
Heat Input ◽  
Base Fluid ◽  
Thermal Characteristics ◽  
Working Fluid ◽  
Two Phase ◽  
Evaporation And Condensation

The two-phase closed thermosyphon (TPCT), which is essentially a gravity-assisted wickless heat pipe, utilizes the evaporation and condensation of the working fluid inside the TPCT to transport heat. This experimental study was carried out to understand the thermal performance of circular finned thermosyphon using nanofluid with alcohol and was analyzed, compared with alcohol and base fluid DI water. The concentration of nanoparticle used in this setup was 110mg/lit of TiO2combined with 0.2 ml of ethylene glycol. The heat input (Q) were 10W, 12W, 14 W and 16 W and the orientation 30°, 45°, 60° and 90°.The results demonstrate that TiO2nanofluid with 0.2 ml of ethylene glycol improves the performance through reduction in thermal resistance by 85.86%.

Numerical Simulation of Rayleigh–Taylor Instability by Multiphase MPS Method

2018 ◽  
Vol 16 (02) ◽  
pp. 1846005
Author(s):  
Xiao Wen ◽  
Decheng Wan
Keyword(s):  
Numerical Simulation ◽  
Hydrodynamic Instability ◽  
Phase Interface ◽  
Industrial Applications ◽  
Taylor Instability ◽  
Transitional Region ◽  
Two Phase ◽  
Mps Method ◽  
Evolutionary Features ◽  
Rayleigh Taylor Instability

The Rayleigh–Taylor instability (RTI) problem is one of the classic hydrodynamic instability cases in natural scenarios and industrial applications. For the numerical simulation of the RTI problem, this paper presents a multiphase method based on the moving particle semi-implicit (MPS) method. Herein, the incompressibility of the fluids is satisfied by solving a Poisson Pressure Equation (PPE) and the pressure fluctuation is suppressed. A single set of equations is utilized for fluids with different densities, making the method relatively simple. To deal with the mathematical discontinuity of density in the two-phase interface, a transitional region is introduced into this method. For particles in the transitional region, a density smoothing scheme is applied to improve the numerical stability. The simulation results show that the present MPS multiphase method is capable of capturing the evolutionary features of the RTI, even in the later stage when the two-phase interface is quite distorted. The unphysical penetration in the interface is limited, proving the stability and accuracy of the proposed method.

Sign in / Sign up

Export Citation Format

Share Document