Effect of Hydrogen On Steady-State and Transient Combustion Instability Characteristics

2020 ◽  
Author(s):  
John Strollo ◽  
Stephen Peluso ◽  
Jacqueline O'Connor
Keyword(s):  
Steady State ◽  
High Speed ◽  
Pressure Fluctuations ◽  
Heat Rate ◽  
Flame Stabilization ◽  
Operating Conditions ◽  
System Stability ◽  
Chamber Pressure ◽  
Thermoacoustic Instability ◽  
Hydrogen Addition

Abstract This paper examines the effects of steady-state and transient hydrogen enrichment on thermoacoustic instability in a model gas turbine combustor. Measurements of combustor chamber pressure fluctuations and CH* chemiluminescence imaging are used to characterize instability at a range of operating conditions. Steady-state tests show that both mixture heat rate and hydrogen content affect system stability. At a given heat rate, higher levels of hydrogen result in unstable combustion. As heat rate increases, instability occurs at lower concentrations of hydrogen in the fuel. Transient operation was tested in two directions - instability onset and decay - and two hydrogen-addition times - a short time of 1 millisecond and a longer time of 4 seconds. Results show that instability onset processes, through the transient addition of hydrogen, are highly repeatable regardless of the timescale of hydrogen addition. Certain instability decay processes are less repeatable, resulting in cases that do not fully transition from unstable to stable combustion despite similar changes in hydrogen fuel flow rate. Flame behavior before, during, and after the transient is characterized using high-speed CH* chemiluminescence imaging. Analysis of the high-speed images show changes in flame stabilization and dynamics during the onset and decay processes. The results of this study can have implications for systems that experience variations in fuel composition, particularly in light of growing interest in hydrogen as a renewable fuel.

Effect of Hydrogen on Steady-State and Transient Combustion Instability Characteristics

2020 ◽  
Author(s):  
John Strollo ◽  
Stephen Peluso ◽  
Jacqueline O’Connor
Keyword(s):  
Steady State ◽  
High Speed ◽  
Combustion Instability ◽  
Heat Rate ◽  
Flame Stabilization ◽  
Operating Conditions ◽  
System Stability ◽  
Chamber Pressure ◽  
Thermoacoustic Instability ◽  
Hydrogen Addition

Abstract This paper examines the effects of steady-state and transient hydrogen enrichment on thermoacoustic instability in a model gas turbine combustor. Combustion instability, a feedback loop between flame heat release rate oscillations and combustor acoustics, is characterized in a swirl-stabilized flame operated at a range of hydrogen-natural gas fuel blends and heat rates. Measurements of combustor chamber pressure fluctuations and CH* chemiluminescence imaging are used to characterize instability at a range of operating conditions. Steady-state tests show that both mixture heat rate and hydrogen content affect system stability. At a given heat rate, higher levels of hydrogen result in unstable combustion. As heat rate increases, instability occurs at lower concentrations of hydrogen in the fuel. Transient operation was tested in two directions — instability onset and decay — and two hydrogen-addition times — a short time of 1 millisecond and a longer time of 4 seconds. Results show that instability onset processes, through the transient addition of hydrogen, are highly repeatable regardless of the timescale of hydrogen addition. Certain instability decay processes are less repeatable, resulting in cases that do not fully transition from unstable to stable combustion despite similar changes in hydrogen fuel flow rate. Flame behavior before, during, and after the transient is characterized using high-speed CH* chemiluminescence imaging. Analysis of the high-speed images show changes in flame stabilization and dynamics during the onset and decay processes. The results of this study can have implications for systems that experience variations in fuel composition, particularly in light of growing interest in hydrogen as a renewable fuel.

scholarly journals The Influence of Carrier Air Preheating on Autoignition of Inline-Injected Hydrogen–Nitrogen Mixtures in Vitiated Air of High Temperature

2017 ◽  
Vol 140 (3) ◽  
Author(s):  
Christoph A. Schmalhofer ◽  
Peter Griebel ◽  
Manfred Aigner
Keyword(s):  
Hydrogen Content ◽  
Gas Turbines ◽  
High Speed ◽  
Flame Stabilization ◽  
Operating Conditions ◽  
Promoting Effect ◽  
Experimental Conditions ◽  
Lean Premixed Combustion ◽  
Image Velocimetry ◽  
Fuel Mixtures

The use of highly reactive hydrogen-rich fuels in lean premixed combustion systems strongly affects the operability of stationary gas turbines (GT) resulting in higher autoignition and flashback risks. The present study investigates the autoignition behavior and ignition kernel evolution of hydrogen–nitrogen fuel mixtures in an inline co-flow injector configuration at relevant reheat combustor operating conditions. High-speed luminosity and particle image velocimetry (PIV) measurements in an optically accessible reheat combustor are employed. Autoignition and flame stabilization limits strongly depend on temperatures of vitiated air and carrier preheating. Higher hydrogen content significantly promotes the formation and development of different types of autoignition kernels: More autoignition kernels evolve with higher hydrogen content showing the promoting effect of equivalence ratio on local ignition events. Autoignition kernels develop downstream a certain distance from the injector, indicating the influence of ignition delay on kernel development. The development of autoignition kernels is linked to the shear layer development derived from global experimental conditions.

Scale Resolving CFD Investigations of Aerothermal Field and Emissions of a Lean Burn Aeroengine Combustor

2021 ◽  
Author(s):  
S. Paccati ◽  
L. Mazzei ◽  
A. Andreini ◽  
S. Patil ◽  
S. Shrivastava ◽  
...  
Keyword(s):  
Pressure Fluctuations ◽  
Computational Cost ◽  
Flame Stabilization ◽  
Operating Conditions ◽  
Tetrahedral Mesh ◽  
Main Stream ◽  
Nox Emissions ◽  
Lean Burn ◽  
Emission Data ◽  
Hexahedral Elements

Abstract Due to the increasingly stringent international limitations in terms of NOx emissions, the development of new combustor concepts has become extremely important in order for aircraft engines to comply with these regulations. In this framework, lean-burn technology represents a promising solution and several studies and emission data from production engines have proven that it is more promising in reducing NOx emissions than rich-burn technology. Considering the drawbacks of this combustion strategy (flame stabilization, flashback or blowout or the occurrence of large pressure fluctuations causing thermo-acoustics phenomena) as well as the difficulties and the high costs related to experimental campaigns at relevant operating conditions, Computational Fluid Dynamics (CFD) plays a key role in deepening understanding of the complex phenomena that are involved in such reactive conditions. During last years, large research efforts have been devoted to develop new advanced numerical strategies for high-fidelity predictions in simulating reactive flows that feature strong unsteadiness and high levels of turbulence intensity with affordable computational resources. In this sense, hybrid RANS-LES models represent a good compromise between accurate prediction of flame behaviour and computational cost with respect to fully-LES approaches. Stress-Blended Eddy Simulation (SBES) is a new global hybrid RANS-LES methodology which ensures an improved shielding of RANS boundary layers and a more rapid RANS-LES “transition” compared to other hybrid RANS-LES formulations. In the present work, a full annular aeronautical lean-burn combustor operated at real conditions is investigated from a numerical point of view employing the new SBES approach using poly-hexcore mesh topology, which allows to adopt an isotropic grid for more accurate scale-resolving calculations by means of fully regular hexahedral elements in the main stream. The results are compared to experimental data and to previous reference numerical results obtained with Scale Adaptive Simulation formulation on a tetrahedral mesh grid in order to underline the improvements achieved with the new advanced numerical setup.

scholarly journals Strong Azimuthal Combustion Instabilities in a Spray Annular Chamber With Intermittent Partial Blow-Off

2017 ◽  
Vol 140 (3) ◽  
Author(s):  
Kevin Prieur ◽  
Daniel Durox ◽  
Thierry Schuller ◽  
Sébastien Candel
Keyword(s):  
Light Intensity ◽  
High Speed ◽  
Transverse Velocity ◽  
Pressure Fluctuations ◽  
Pressure Sensors ◽  
Nodal Line ◽  
Operating Conditions ◽  
Acoustic Energy ◽  
Transverse Motion ◽  
Azimuthal Mode

This article reports experiments carried out in the MICCA-spray combustor developed at EM2C laboratory. This system comprises 16 swirl spray injectors. Liquid n-heptane is injected by simplex atomizers. The combustion chamber is formed by two cylindrical quartz tubes allowing full optical access to the flame region and it is equipped with 12 pressure sensors recording signals in the plenum and chamber. A high-speed camera provides images of the flames and photomultipliers record the light intensity from different flames. For certain operating conditions, the system exhibits well defined instabilities coupled by the first azimuthal mode of the chamber at a frequency of 750 Hz. These instabilities occur in the form of bursts. Examination of the pressure and the light intensity signals gives access to the acoustic energy source term. Analysis of the phase fluctuations between the two signals is carried out using cross-spectral analysis. At limit cycle, large pressure fluctuations of 5000 Pa are reached, and these levels persist over a finite period of time. Analysis of the signals using the spin ratio indicates that the standing mode is predominant. Flame dynamics at the pressure antinodal line reveals a strong longitudinal pulsation with heat release rate oscillations in phase and increasing linearly with the acoustic pressure for every oscillation levels. At the pressure nodal line, the flames are subjected to large transverse velocity fluctuations leading to a transverse motion of the flames and partial blow-off. Scenarios and modeling elements are developed to interpret these features.

Subsynchronous Vibration Patterns Under Reduced Oil Supply Flow Rates

2017 ◽  
Author(s):  
B. R. Nichols ◽  
R. L. Fittro ◽  
C. P. Goyne
Keyword(s):  
Flow Rate ◽  
High Speed ◽  
Operating Conditions ◽  
System Stability ◽  
Supporting Evidence ◽  
Test Rig ◽  
Flow Rates ◽  
Oil Supply ◽  
Bending Mode ◽  
Wide Range

Many high-speed, rotating machines across a wide range of industrial applications depend on fluid film bearings to provide both static support of the rotor and to introduce stabilizing damping forces into the system through a developed hydrodynamic film wedge. Reduced oil supply flow rate to the bearings can cause cavitation, or a lack of a fully developed film layer, at the leading edge of the bearing pads. Reducing oil flow has the well-documented effects of higher bearing operating temperatures and decreased power losses due to shear forces. While machine efficiency may be improved with reduced lubricant flow, little experimental data on its effects on system stability and performance can be found in the literature. This study looks at overall system performance of a test rig operating under reduced oil supply flow rates by observing steady-state bearing performance indicators and baseline vibrational response of the shaft. The test rig used in this study was designed to be dynamically similar to a high-speed industrial compressor. It consists of a 1.55 m long, flexible rotor supported by two tilting pad bearings with a nominal diameter of 70 mm and a span of 1.2 m. The first bending mode is located at approximately 5,000 rpm. The tiling-pad bearings consist of five pads in a vintage, flooded bearing housing with a length to diameter ratio of 0.75, preload of 0.3, and a load-between-pad configuration. Tests were conducted over a number of operating speeds, ranging from 8,000 to 12,000 rpm, and bearing loads, while systematically reducing the oil supply flow rates provided to the bearings under each condition. For nearly all operating conditions, a low amplitude, broadband subsynchronous vibration pattern was observed in the frequency domain from approximately 0–75 Hz. When the test rig was operated at running speeds above its first bending mode, a distinctive subsynchronous peak emerged from the broadband pattern at approximately half of the running speed and at the first bending mode of the shaft. This vibration signature is often considered a classic sign of rotordynamic instability attributed to oil whip and shaft whirl phenomena. For low and moderate load conditions, the amplitude of this 0.5x subsynchronous peak increased with decreasing oil supply flow rate at all operating speeds. Under the high load condition, the subsynchronous peak was largely attenuated. A discussion on the possible sources of this subsynchronous vibration including self-excited instability and pad flutter forced vibration is provided with supporting evidence from thermoelastohydrodynamic (TEHD) bearing modeling results. Implications of reduced oil supply flow rate on system stability and operational limits are also discussed.

Impact of Impeller Casing Treatment on the Acoustics of a Small High Speed Centrifugal Compressor

2018 ◽  
Author(s):  
Sidharath Sharma ◽  
Jorge García-Tíscar ◽  
John M. Allport ◽  
Martyn L. Jupp ◽  
Ambrose K. Nickson
Keyword(s):  
Centrifugal Compressor ◽  
High Speed ◽  
Pressure Fluctuations ◽  
Operating Conditions ◽  
Aerodynamic Noise ◽  
Noise Sources ◽  
Casing Treatment ◽  
Active Research ◽  
Ported Shroud ◽  
The Impact

Ported shroud casing treatment is widely used to delay the onset of surge and thereby enhancing the aerodynamic stability of a centrifugal compressor by recirculating the low momentum fluid in the blade passage. Performance losses associated with the use of recirculation casing treatment are well established in the literature and this is an area of active research. The other, less researched aspect of the casing treatment is its impact on the acoustics of the compressor. This work investigates the impact of ported shroud casing treatment on the acoustic characteristics of the compressor. The flow in two compressor configurations viz. with and without casing treatment operating at the design operating conditions of an iso-speed line are numerically modelled and validated with experimental data from gas stand measurements. The pressure fluctuations calculated as the flow solution are used to compute the spectral signatures at multiple locations to investigate the acoustic phenomenon associated with each configuration. Propagation of the frequency content through the ducts has been estimated with the aid of method of characteristics to enhance the content coming from the compressor. Expected tonal aerodynamic noise sources such as monopole (buzz-saw tones) and dipole (Blade Pass Frequency) are clearly identified in the acoustic spectra of the two configurations. The comparison of two configurations shows higher overall levels and tonal content in the case of a compressor with ported shroud operating at design conditions due to the presence of ‘mid-tones’.

Study of Dynamical Instabilities in Siemens Liquid Spray Injectors Using Complementary Modal Decomposition Techniques

2019 ◽  
Author(s):  
Adesile Ajisafe ◽  
Midhat Talibi ◽  
Andrea Ducci ◽  
Ramanarayanan Balachandran ◽  
Nishant Parsania ◽  
...  
Keyword(s):  
High Speed ◽  
Dynamical Behaviour ◽  
Operating Conditions ◽  
Dynamic Mode Decomposition ◽  
Fuel Spray ◽  
Chamber Pressure ◽  
Dynamic Mode ◽  
Decomposition Techniques ◽  
Planar Imaging ◽  
Modal Decomposition

Abstract Liquid fuel spray characterisation is essential for understanding the mechanisms underlying fuel energy release and pollutant formation. Careful selection of operating conditions can promote flow instabilities in the fuel spray which can enhance atomisation and fuel mixing, thereby resulting in more efficient combustion. However, the inherent instabilities present in the spray could have adverse effect on the combustor dynamics. Hence, it is important to better understand the dynamical behaviour of the spray, and particularly at representative operating conditions. This work describes an experimental investigation of dynamical behaviour of pressure-swirl atomisers used in Siemens industrial gas turbine combustors, at a range of chamber pressures and fuel injection pressures, using high speed laser planar imaging. Two modal decomposition techniques — Proper Orthogonal Decomposition (POD) and Dynamic Mode Decomposition (DMD) — are applied and compared to assess the spray dynamics. Results indicate that both POD and DMD are able to capture periodic structures occurring in the spray at different spatial length scales. The characteristic frequencies estimated from both the methods are in good agreement with each other. Both techniques are able to identify coherent structures with variable size, shape and level of staggering, which are observed to be dependent on the pressure difference across the atomiser and the chamber pressure. The spatio-temporally resolved data and the results could be used for spray model development and validation. Furthermore, the methods employed could be applied to other fuel atomisers, and more complicated conditions involving cross flow and higher chamber temperatures.

Paper 1: Computer Solution of Surge Problems

1965 ◽  
Vol 180 (5) ◽  
pp. 62-82
Author(s):  
Victor L. Streeter
Keyword(s):  
Steady State ◽  
Differential Equations ◽  
High Speed ◽  
Transient Flow ◽  
Nonlinear Differential Equations ◽  
Pressure Fluctuations ◽  
Transient Pressure ◽  
Pump Failure ◽  
Flow Equations ◽  
Flow Impedance

Methods for handling the transient flow equations are developed for application of the high-speed digital computer. For incompressible flow cases ordinary nonlinear differential equations occur which are solved simultaneously by established sub-routines on the computer, such as the Runge-Kutta method. For the partial differential equations of compressible water hammer with nonlinear terms such as friction, the method of characteristics and of specified time intervals are employed for those problems in which the flow changes from one steady-state to another steady-state. For steady-oscillatory flow, impedance methods have been adapted to the computer with harmonic analysis of the exciting disturbance. Experimental evidence is presented to confirm the accuracy of the procedures for single and series pipes, for pump failures, and for reciprocating pumps. Additionally the design problem of optimum operation of a valve to minimize transient pressure fluctuations has been introduced and applied to single and series pipes, including a pump failure situation.

Autoignition of Hydrogen / Natural Gas / Nitrogen Fuel Mixtures at Reheat Combustor Operating Conditions

2012 ◽  
Author(s):  
Julia Fleck ◽  
Peter Griebel ◽  
Manfred Aigner ◽  
Adam M. Steinberg
Keyword(s):  
Natural Gas ◽  
High Speed ◽  
Volume Fraction ◽  
Fluid Dynamic ◽  
Flame Stabilization ◽  
Operating Conditions ◽  
Mixing Zone ◽  
Fuel Injector ◽  
Jet Penetration ◽  
Penetration Depths

Previous autoignition studies at conditions relevant to reheat combustor operation have indicated that the presence of relatively small amounts of natural gas (NG) in H2/N2 fuel significantly changes the autoignition behavior. The present study further elucidates the influence of NG on autoignition, kernel propagation, and subsequent flame stabilization at conditions that are relevant for the practical operation of gas turbine reheat combustors (p = 15 bar, Tinlet > 1000 K, hot flue gas, appropriate residence times). The experimental investigation was carried out in a generic, optically accessible reheat combustor. Autoignition events in the mixing zone were recorded by a high-speed camera at frame rates of up to 30,000 fps. This paper describes the autoignition behavior as the H2 volume fraction is increased (decreasing NG) in a H2/NG/N2 fuel mixture for two different jet penetration depths. Additionally, the subsequent flame stabilization phenomena and the structure of the stabilized flame are discussed. The results reveal that autoignition kernels occurred even for the lowest H2 fuel fraction, but they did not initiate a stable flame in the mixing zone. Increasing the H2 volume fraction decreased the distance between the initial position of the autoignition kernels and the fuel injector, finally leading to flame stabilization. The occurrence of autoignition kernels at lower H2 volume fractions (H2/(H2+NG) < 85%) was not found to be significantly influenced by the fluid dynamic and mixing field differences related to the different jet penetration depths. In contrast, autoignition leading to flame stabilization was found to depend on jet penetration; flame stabilization occurred at lower H2 fractions for the higher jet penetration depth (H2/(H2+NG) ≈ 89 compared to H2/(H2+NG) ≈ 95 vol. %).

Nonlinear Heat-Release/Acoustic Model for Thermoacoustic Instability in Lean Premixed Combustors

1999 ◽  
Vol 121 (3) ◽  
pp. 415-421 ◽  
Author(s):  
A. A. Peracchio ◽  
W. M. Proscia
Keyword(s):  
Heat Release ◽  
Limit Cycle ◽  
Gas Turbines ◽  
Pressure Fluctuations ◽  
Parametric Model ◽  
Operating Conditions ◽  
Cycle Frequency ◽  
Thermoacoustic Instability ◽  
Lean Premixed ◽  
Industrial Gas Turbines

Lean premixed combustors, such as those used in industrial gas turbines to achieve low emissions, are often susceptible to the thermoacoustic combustion instabilities, which manifest themselves as pressure and heat release oscillations in the combustor. These oscillations can result in increased noise and decreased durability due to vibration and flame motion. A physically based nonlinear parametric model has been developed that captures this instability. It describes the coupling of combustor acoustics with the rate of heat release. The model represents this coupling by accounting for the effect of acoustic pressure fluctuations on the varying fuel/air ratio being delivered to the flame, causing a fluctuating heat release due to both fuel air ratio variations and flame front oscillations. If the phasing of the fluctuating heat release and pressure are proper, an instability results that grows into a limit cycle. The nonlinear nature of the model predicts the onset of the instability and additionally captures the resulting limit cycle. Tests of a lean premixed nozzle run at engine scale and engine operating conditions in the UTRC single nozzle rig, conducted under DARPA contract, exhibited instabilities. Parameters from the model were adjusted so that analytical results were consistent with relevant experimental data from this test. The parametric model captures the limit cycle behavior over a range of mean fuel air ratios, showing the instability amplitude (pressure and heat release) to increase and limit cycle frequency to decrease as mean fuel air ratio is reduced.

Sign in / Sign up

Export Citation Format

Share Document