Electrowetting Induced Droplet Generation in T-junctions

2021 ◽  
Author(s):  
Arshia Merdasi ◽  
Ali Moosavi
Keyword(s):  
Shear Stress ◽  
Continuous Phase ◽  
Droplet Breakup ◽  
Droplet Generation ◽  
The Finite Element Method ◽  
Fluidic Channel ◽  
Generation Frequency ◽  
Two Phases ◽  
Breakup Time ◽  
Good Agreement

Abstract In the current study, droplet generation in a T-junction fluidic channel device was studied through using electrowetting actuation with the consideration of different droplet forming regimes. For this purpose, the finite element method (FEM) was used to solve the unsteady Naiver-Stokes equation. In addition, the level set method was applied to capture the interface between two phases. It was shown that there was a good agreement between obtained data and other work during the process of droplet generation in the absence of electrowetting actuation which results in decrease in the size of droplet with increasing the velocity ratios. In shearing regime, the effectiveness of electrowetting on the droplet generation frequency as well as droplet size is visible in a T-junction fluidic channel since after applying voltages, specified with non-dimensional electrowetting numbers of ?=0.5 and 1.2, dispersed phase is pulled out into the oil phase. In fact, with applying the voltage on the top wall, the droplet breakup time was decreased and smaller droplets were produced. Finally, different important parameters such as pressure difference across the interface as well as Shear Stress exerted from the continuous phase shear stress were examined in a detail.

Numerical study of droplet breakup in an asymmetric T-junction microchannel with different cross-section ratios

2021 ◽  
pp. 2250023
Author(s):  
Milad Isanejad ◽  
Keivan Fallah
Keyword(s):  
Cross Section ◽  
Numerical Study ◽  
Three Dimensional ◽  
Droplet Breakup ◽  
Width Ratio ◽  
Two Phase ◽  
Droplet Motion ◽  
Daughter Droplets ◽  
Breakup Time ◽  
Good Agreement

In this study, numerical simulations are conducted to investigate droplet breakup in an asymmetric [Formula: see text]-junction microchannel with different cross-section ratios. To this approach, a two-phase model based on the volume of fluid (VOF) method is adopted to study the three-dimensional feature of droplet motion inside [Formula: see text]-junctions. The comparison reveals that the present results are in good agreement with previous studies. The effects of the capillary number (Ca), the non-dimensional droplet length ([Formula: see text]), and the non-dimensional width ratio ([Formula: see text]) on the breakup time and splitting ratio of daughter droplets are studied. Five distinct regimes are observed involving the non-breakup, breakup with tunnel, breakup without tunnel, asymmetric breakup, and sorting. Achieved results indicate that the time of breakup ([Formula: see text]) increases about 15% when the Ca is increased from 0.0134 to 0.0268 (about 100%). It is also found that the mass center of the mother droplet in the primary channel is shifted to a larger wide branch, which facilitates the asymmetric breakup of the droplet in a [Formula: see text]-junction microchannel.

scholarly journals Numerical Analysis of Supersonic Impinging Jet Flows of Particle-Gas Two Phases

Processes ◽  
2020 ◽  
Vol 8 (2) ◽  
pp. 191
Author(s):  
Zhang ◽  
Ma ◽  
Kim ◽  
Lin
Keyword(s):  
Shear Stress ◽  
Supersonic Nozzle ◽  
Particle Diameter ◽  
Impinging Jet ◽  
Continuous Phase ◽  
Jet Flows ◽  
Discrete Phase Model ◽  
Sonic Nozzle ◽  
Supersonic Impinging Jet ◽  
Two Phases

Supersonic impinging jet flows always occur when aircrafts start short takeoff and vertical landing from the ground. Supersonic flows with residues produced by chemical reaction of fuel mixture have the potential of reducing aircraft performance and landing ground. The adverse flow conditions such as impinging force, high noise spectrum, and high shear stress always take place. Due to rare data on particle-gas impinging jet flows to date, three-dimensional numerical simulations were carried out to investigate supersonic impinging jet flows of particle-gas two phases in the present studies. A convergent sonic nozzle and a convergent-divergent supersonic nozzle were used to induce supersonic impinging jet flows. Discrete phase model (DPM), where interaction with continuous phase and two-way turbulence coupling model were considered, was used to simulate particle-gas flows. Effects of different particle diameter and Stokes number were investigated. Particle mass loading of 10% were considered for all simulations. Gas and particle velocity contours, wall shear stress, and impinging force on the ground surface were obtained to describe different phenomena inside impinging and wall jet flows of single gas phase and gas-particle two phases.

Analysis of the Contact Deformation of Tread Blocks

1992 ◽  
Vol 20 (4) ◽  
pp. 230-253 ◽  
Author(s):  
T. Akasaka ◽  
K. Kabe ◽  
M. Koishi ◽  
M. Kuwashima
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Deformation Behavior ◽  
Contact Deformation ◽  
The Finite Element Method ◽  
The Road ◽  
Loss Of Contact ◽  
Tread Rubber ◽  
Good Agreement ◽  
Rubber Block

Abstract The deformation behavior of a tire in contact with the roadway is complicated, in particular, under the traction and braking conditions. A tread rubber block in contact with the road undergoes compression and shearing forces. These forces may cause the loss of contact at the edges of the block. Theoretical analysis based on the energy method is presented on the contact deformation of a tread rubber block subjected to compressive and shearing forces. Experimental work and numerical calculation by means of the finite element method are conducted to verify the predicted results. Good agreement is obtained among these analytical, numerical, and experimental results.

Dynamic Behavior Analysis of the Slider Crank Linkage using ANSYS Workbench and MATLAB Program

2013 ◽  
Vol 1 (1) ◽  
pp. 42-25
Author(s):  
Nabil N. Swadi
Keyword(s):  
Graphical Method ◽  
Joint Torque ◽  
Pressure Force ◽  
Matlab Program ◽  
Element Simulation ◽  
Acceleration Method ◽  
Complete Revolution ◽  
Two Phases ◽  
Good Agreement ◽  
Ansys Workbench

This paper is concerned with the study of the kinematic and kinetic analysis of a slider crank linkage using D'Alembert's principle. The links of the considered mechanism are assumed to be rigid. The analytical solution to observe the motion (displacement, velocity, and acceleration), reactions at each joint, torque required to drive the mechanism and the shaking force have been computed by a computer program written in MATLAB language over one complete revolution of the crank shaft. The results are compared with a finite element simulation carried out by using ANSYS Workbench software and are found to be in good agreement. A graphical method (relative velocity and acceleration method) has been also applied for two phases of the crank shaft (q2 = 10° and 130°). The results obtained from this method (graphical) are compared with those obtained from analytical and numerical method and are found very acceptable. To make the analysis linear the friction force on the joints and sliding interface are neglected. All results, in this work, are obtained when the crank shaft turns at a uniform angular velocity (w2 = 188.5 rad/s) and time dependent gas pressure force on the slider crown.

scholarly journals Study of Influence of Width to Thickness Ratio in Sheet Metals on Bendability under Ambient and Superimposed Hydrostatic Pressure

2021 ◽  
Vol 2 (3) ◽  
pp. 542-558
Author(s):  
Mohammadmehdi Shahzamanian ◽  
David Lloyd ◽  
Amir Partovi ◽  
Peidong Wu
Keyword(s):  
Hydrostatic Pressure ◽  
Stress Ratio ◽  
Fracture Strain ◽  
Stress Triaxiality ◽  
Volumetric Strain ◽  
Thickness Ratio ◽  
Sheet Metals ◽  
The Finite Element Method ◽  
Bending Strain ◽  
Good Agreement

The effect of the width to thickness ratio on the bendability of sheet metal is investigated using the finite element method (FEM) employing the Gurson–Tvergaard–Needleman (GTN) model. Strain path changes in the sheet with change in the width/thickness ratio. It is shown that bendability and fracture strain increase significantly by decrease in the width/thickness ratio. The stress state is almost uniaxial when the stress ratio (α) is close to zero for narrow sheets. Stress ratio is nothing but the major stress to minor stress ratio. This delays the growth and coalescence of micro-voids as the volumetric strain and stress triaxiality (pressure/effective stress) decrease. On the other hand, ductility decreases with increase in α for wider sheets. Fracture bending strain is calculated and, as expected, it increases with decrease in the width/thickness ratio. Furthermore, a brief study is performed to understand the effect of superimposed hydrostatic pressure on fracture strain for various sheet metals with different width/thickness ratios. It is found that the superimposed hydrostatic pressure increases the ductility, and that the effect of the width/thickness ratio in metals on ductility is as significant as the effect of superimposed hydrostatic pressure. Numerical results are found to be in good agreement with experimental observations.

scholarly journals Comparison of Experimental and Numerical Transient Drop Deformation during Transition through Orifices in High-Pressure Homogenizers

2021 ◽  
Vol 5 (3) ◽  
pp. 32
Author(s):  
Benedikt Mutsch ◽  
Peter Walzel ◽  
Christian J. Kähler
Keyword(s):  
High Pressure ◽  
Visual Analysis ◽  
Imaging Technique ◽  
Extensional Flow ◽  
Droplet Breakup ◽  
Experimental Results ◽  
Drop Deformation ◽  
Droplet Deformation ◽  
Shadow Imaging ◽  
Good Agreement

The droplet deformation in dispersing units of high-pressure homogenizers (HPH) is examined experimentally and numerically. Due to the small size of common homogenizer nozzles, the visual analysis of the transient droplet generation is usually not possible. Therefore, a scaled setup was used. The droplet deformation was determined quantitatively by using a shadow imaging technique. It is shown that the influence of transient stresses on the droplets caused by laminar extensional flow upstream the orifice is highly relevant for the droplet breakup behind the nozzle. Classical approaches based on an equilibrium assumption on the other side are not adequate to explain the observed droplet distributions. Based on the experimental results, a relationship from the literature with numerical simulations adopting different models are used to determine the transient droplet deformation during transition through orifices. It is shown that numerical and experimental results are in fairly good agreement at limited settings. It can be concluded that a scaled apparatus is well suited to estimate the transient droplet formation up to the outlet of the orifice.

Effect of Geometry on Droplet Generation in a Microfluidic T-Junction

2013 ◽  
Author(s):  
Katerina Loizou ◽  
Wim Thielemans ◽  
Buddhika N. Hewakandamby
Keyword(s):  
Aspect Ratio ◽  
Cross Section ◽  
Droplet Formation ◽  
Continuous Phase ◽  
Main Channel ◽  
Superficial Velocity ◽  
Droplet Generation ◽  
Dispersed Phase ◽  
Aspect Ratios ◽  
The Cross

The main aim of this study is to examine how the droplet formation in microfluidic T-junctions is influenced by the cross-section and aspect ratio of the microchannels. Several studies focusing on droplet formation in microfluidic devices have investigated the effect of geometry on droplet generation in terms of the ratio between the width of the main channel and the width of the side arm of the T-junction. However, the contribution of the aspect ratio and thus that of the cross-section on the mechanism of break up has not been examined thoroughly with most of the existing work performed in the squeezing regime. Two different microchannel geometries of varying aspect ratios are employed in an attempt to quantify the effect of the ratio between the width of the main channel and the height of the channel on droplet formation. As both height and width of microchannels affect the area on which shear stress acts deforming the dispersed phase fluid thread up to the limit of detaching a droplet, it is postulated that geometry and specifically cross-section of the main channel contribute on the droplet break-up mechanisms and should not be neglected. The above hypothesis is examined in detail, comparing the volume of generated microdroplets at constant flowrate ratios and superficial velocities of continuous phase in two microchannel systems of two different aspect ratios operating at dripping regime. High-speed imaging has been utilised to visualise and measure droplets formed at different flowrates corresponding to constant superficial velocities. Comparing volumes of generated droplets in the two geometries of area ratio near 1.5, a significant increase in volume is reported for the larger aspect ratio utilised, at all superficial velocities tested. As both superficial velocity of continuous phase and flowrate ratio are fixed, superficial velocity of dispersed phase varies. However this variation is not considered to be large enough to justify the significant increase in the droplet volume. Therefore it can be concluded that droplet generation is influenced by the aspect ratio and thus the cross-section of the main channel and its effect should not be depreciated. The paper will present supporting evidence in detail and a comparison of the findings with the existing theories which are mainly focused on the squeezing regime.

An analytical model of an I-cored coil located above a conductive material with a hole

2018 ◽  
Vol 82 (2) ◽  
pp. 21001
Author(s):  
Grzegorz Tytko ◽  
Leszek Dziczkowski
Keyword(s):  
Test Object ◽  
Middle Layer ◽  
Axially Symmetric ◽  
The Finite Element Method ◽  
Cylindrical Coordinate ◽  
Air Space ◽  
Through Hole ◽  
Tree Method ◽  
Good Agreement ◽  
Made In

The paper examines the problem of an axially symmetric I-cored coil located above a three-layered plate with a hole in the middle layer. A cylindrical coordinate system was applied, wherein the solution domain was truncated in the radial direction. The employment of the truncated region eigenfunction expansion (TREE) method resulted in deriving the final formulas for the change of the coil impedance with regard to the air space, and also pertaining to the test object without a flaw. Formulas for various configurations of the test object, among others for a surface hole, a subsurface hole and a through hole, have been presented. For the purpose of defectoscopy, the influence of the hole in the plate on the impedance components was investigated. The calculations were made in Matlab for frequencies from 100 Hz to 50 kHz. The obtained results were verified using the finite element method (FEM) in Comsol Multiphysics package. A very good agreement was observed in the case of both the resistance and reactance.

scholarly journals In-Depth Verification of a Numerical Model for an Axisymmetric RC Dome

Symmetry ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 2152
Author(s):  
Przemysław Czumaj ◽  
Sławomir Dudziak ◽  
Zbigniew Kacprzyk
Keyword(s):  
Three Dimensional ◽  
Spatial Models ◽  
Detailed Comparison ◽  
The Finite Element Method ◽  
Robot System ◽  
Engineering Structures ◽  
Computational Analyses ◽  
Computational Systems ◽  
Good Agreement ◽  
Made In

The designers of civil engineering structures often have to face the problem of the reliability of complex computational analyses performed most often with the Finite Element Method (FEM). Any assessment of reliability of such analyses is difficult and can only be approximate. The present paper puts forward a new method of verification and validation of the structural analyses upon an illustrative example of a dome strengthened by circumferential ribs along the upper and lower edges. Four computational systems were used, namely Abaqus, Autodesk Robot, Dlubal RFEM, and FEAS. Different models were also analyzed—two-dimensional (2D) and three-dimensional (3D) ones using continuum, bar, and shell finite elements. The results of the static (with two kinds of load—self-weight and load distributed along the upper ring) and modal analyses are presented. A detailed comparison between the systems’ and models’ predictions was made. In general, the spatial models predicted a less stiff behavior of the analyzed dome than the planar models. The good agreement between different models and systems was obtained for the first natural frequency with axisymmetric eigenmodes (except from the Autodesk Robot system). The presented approach to the verification of complex shell–bar models can be effectively applied by structural designers.

Vibration Analysis for Piezoceramic Circular Plates with V-Notches. Part 1: Theory

2014 ◽  
Vol 30 (6) ◽  
pp. 603-609 ◽  
Author(s):  
C.-H. Huang ◽  
Y.-Y. Chen
Keyword(s):  
Theoretical Analysis ◽  
Transverse Vibration ◽  
Stress Singularity ◽  
Trigonometric Polynomials ◽  
Circular Plates ◽  
The Finite Element Method ◽  
Electrical Field ◽  
Ritz’S Method ◽  
Frequency Variations ◽  
Good Agreement

AbstractIn this paper the transverse vibration characteristics of piezoceramic circular plates with V-notches are investigated theoretically through use of the Ritz's method incorporated with the defined equivalent constants. The Ritz's method is employed with two sets of admissible displacement functions, algebraic-trigonometric polynomials and corner functions, to guarantee convergence sufficiently and represent the stress singularity, respectively. Moreover, the equivalent constants derived by comparing the characteristic equations of transverse vibration between isotropic and piezoceramic disks are applied to suspend the electrical field consideration regarding the piezoelectricity. With the aid of theoretical analysis, the non-dimensional frequency parameters of transverse vibration modes for completely free V-notching circular plates are exhibited; in addition, the frequency variations depending on various notch angles and depths are explored. Numerical calculations using the finite element method (FEM) are performed and the results are compared with the theoretical analysis. It is shown that the resonant frequencies predicted by theoretical analysis and calculated by FEM are in good agreement.

Sign in / Sign up

Export Citation Format

Share Document