Numerical study of droplet breakup in an asymmetric T-junction microchannel with different cross-section ratios

2021 ◽  
pp. 2250023
Author(s):  
Milad Isanejad ◽  
Keivan Fallah
Keyword(s):  
Cross Section ◽  
Numerical Study ◽  
Three Dimensional ◽  
Droplet Breakup ◽  
Width Ratio ◽  
Two Phase ◽  
Droplet Motion ◽  
Daughter Droplets ◽  
Breakup Time ◽  
Good Agreement

In this study, numerical simulations are conducted to investigate droplet breakup in an asymmetric [Formula: see text]-junction microchannel with different cross-section ratios. To this approach, a two-phase model based on the volume of fluid (VOF) method is adopted to study the three-dimensional feature of droplet motion inside [Formula: see text]-junctions. The comparison reveals that the present results are in good agreement with previous studies. The effects of the capillary number (Ca), the non-dimensional droplet length ([Formula: see text]), and the non-dimensional width ratio ([Formula: see text]) on the breakup time and splitting ratio of daughter droplets are studied. Five distinct regimes are observed involving the non-breakup, breakup with tunnel, breakup without tunnel, asymmetric breakup, and sorting. Achieved results indicate that the time of breakup ([Formula: see text]) increases about 15% when the Ca is increased from 0.0134 to 0.0268 (about 100%). It is also found that the mass center of the mother droplet in the primary channel is shifted to a larger wide branch, which facilitates the asymmetric breakup of the droplet in a [Formula: see text]-junction microchannel.

Numerical Study of the Three-Dimensional Structure of a Bubble Plume

2000 ◽  
Vol 122 (4) ◽  
pp. 754-760 ◽  
Author(s):  
Y. Murai ◽  
Y. Matsumoto
Keyword(s):  
Numerical Study ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Lagrangian Model ◽  
Dimensional Structure ◽  
Bubble Motion ◽  
Bubble Plume ◽  
Two Phase ◽  
Simulated Flow ◽  
Good Agreement

The whole behavior and the micro scale flow characteristics of a three-dimensional bubble plume are investigated numerically. The bubble plume drives liquid convection in a tank due to strong local two-phase interaction so that the Eulerian-Lagrangian model is formulated with emphasis on the translational motions of the bubble. In this model, each bubble motion is tracked in a bubbly mixture which is treated as a continuum. The three-dimensional numerical results reveal several particular structures, such as swaying and swirling structures of the bubble plume. These simulated flow structures show qualitatively good agreement with the experimental observations. Furthermore, the detailed behavior in the bubble plume is clarified by various analysis to discuss the dominant factors causing such the strong three-dimensionality. [S0098-2202(00)00904-4]

Boundary element method in numerical study of three-dimensional Stokes flows in channels of arbitrary shape

2012 ◽  
Vol 9 (1) ◽  
pp. 94-97
Author(s):  
Yu.A. Itkulova
Keyword(s):  
Boundary Element Method ◽  
Boundary Element ◽  
Cross Section ◽  
Numerical Study ◽  
Three Dimensional ◽  
Cylindrical Tube ◽  
Variable Cross Section ◽  
Variable Cross ◽  
Periodic Flows ◽  
Element Method

In the present work creeping three-dimensional flows of a viscous liquid in a cylindrical tube and a channel of variable cross-section are studied. A qualitative triangulation of the surface of a cylindrical tube, a smoothed and experimental channel of a variable cross section is constructed. The problem is solved numerically using boundary element method in several modifications for a periodic and non-periodic flows. The obtained numerical results are compared with the analytical solution for the Poiseuille flow.

Effect of Vaned Diffuser on a Modified Turbocharger Centrifugal Compressor Performance

2014 ◽  
Vol 663 ◽  
pp. 347-353
Author(s):  
Layth H. Jawad ◽  
Shahrir Abdullah ◽  
Zulkifli R. ◽  
Wan Mohd Faizal Wan Mahmood
Keyword(s):  
Centrifugal Compressor ◽  
Numerical Study ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Aerodynamic Characteristics ◽  
Width Ratio ◽  
Outlet Section ◽  
Suction Surface ◽  
Vaned Diffuser ◽  
Minimum Width

A numerical study that was made in a three-dimensional flow, carried out in a modified centrifugal compressor, having vaned diffuser stage, used as an automotive turbo charger. In order to study the influence of vaned diffuser meridional outlet section with a different width ratio of the modified centrifugal compressor. Moreover, the performance of the centrifugal compressor was dependent on the proper matching between the compressor impeller along the vaned diffuser. The aerodynamic characteristics were compared under different meridional width ratio. In addition, the velocity vectors in diffuser flow passages, and the secondary flow in cross-section near the outlet of diffuser were analysed in detail under different meridional width ratio. Another aim of this research was to study and simulate the effect of vaned diffuser on the performance of a centrifugal compressor. The simulation was undertaken using commercial software so-called ANSYS CFX, to predict numerically the performance charachteristics. The results were generated from CFD and were analysed for better understanding of the fluid flow through centrifugal compressor stage and as a result of the minimum width ratio the flow in diffuser passage tends to be uniformity. Moreover, the backflow and vortex near the pressure surface disappear, and the vortex and detachment near the suction surface decrease. Conclusively, it was observed that the efficiency was increased and both the total pressure ratio and static pressure for minimum width ratio are increased.

Numerical and Experimental Evaluation of Turbulent Flow in Volute

2003 ◽  
Author(s):  
Akitomo Igarashi ◽  
Kazuyuki Toda ◽  
Makoto Yamamoto ◽  
Toshimichi Sakai
Keyword(s):  
Numerical Simulation ◽  
Cross Section ◽  
Three Dimensional ◽  
Experimental Result ◽  
Centrifugal Fan ◽  
Flow Conditions ◽  
Flow Angle ◽  
Fan Performance ◽  
Centrifugal Fans ◽  
Good Agreement

The performance of centrifugal fans is considerably influenced by the design of tongue at the re-circulation port. The flow in the volute of a centrifugal fan was studied both experimentally and numerically. In this experiment, flow angle, pressure and velocity profiles were measured at a large number of locations in the volute. The flow field in the volute passage was analyzed using Computational Fluid Dynamics. The flow was assumed to be three dimensional, turbulent and steady. The numerical simulation produced qualitatively good agreement with the experimental result. The results from experiment and numerical simulation indicated that the adoption of a re-circulating flow port improved fan performance for all flow conditions. In addition, the existence of strong secondary flow was apparent at the cross-section of the volute passage.

Numerical Study on Supersonic Combustor with an Allotype Cavity

2014 ◽  
Vol 694 ◽  
pp. 187-192
Author(s):  
Jin Xiang Wu ◽  
Jian Sun ◽  
Xiang Gou ◽  
Lian Sheng Liu
Keyword(s):  
Alternative Model ◽  
Numerical Study ◽  
Reverse Flow ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Experimental Result ◽  
Navier Stokes ◽  
Cold Flow ◽  
Hypersonic Inlet ◽  
Good Agreement

The three-dimensional coupled explicit Reynolds Averaged Navier–Stokes (RANS) equations and the two equation shear-stress transport k-w (SST k-w) model has been employed to numerically simulate the cold flow field in a special-shaped cavity-based supersonic combustor. In a cross-section shaped rectangular, hypersonic inlet with airflow at Mach 2.0 chamber, shock structures and flow characteristics of a herringbone-shaped boss and a herringbone-shaped cavity models were discussed, respectively. The results indicate: Firstly, according to the similarities of bevel-cutting shock characteristics between the boss case and the cavity case, the boss structure can serve as an ideal alternative model for shear-layer. Secondly, the eddies within cavity are composed of herringbone-spanwise vortexes, columnar vortices in the front and main-spanwise vortexes in the rear, featuring tilting, twisting and stretching. Thirdly, the simulated bottom-flow of cavity is in good agreement with experimental result, while the reverse flow-entrainment resulting from herringbone geometry and pressure gradient. However, the herringbone-shaped cavity has a better performance in fuel-mixing.

Electrowetting Induced Droplet Generation in T-junctions

2021 ◽  
Author(s):  
Arshia Merdasi ◽  
Ali Moosavi
Keyword(s):  
Shear Stress ◽  
Continuous Phase ◽  
Droplet Breakup ◽  
Droplet Generation ◽  
The Finite Element Method ◽  
Fluidic Channel ◽  
Generation Frequency ◽  
Two Phases ◽  
Breakup Time ◽  
Good Agreement

Abstract In the current study, droplet generation in a T-junction fluidic channel device was studied through using electrowetting actuation with the consideration of different droplet forming regimes. For this purpose, the finite element method (FEM) was used to solve the unsteady Naiver-Stokes equation. In addition, the level set method was applied to capture the interface between two phases. It was shown that there was a good agreement between obtained data and other work during the process of droplet generation in the absence of electrowetting actuation which results in decrease in the size of droplet with increasing the velocity ratios. In shearing regime, the effectiveness of electrowetting on the droplet generation frequency as well as droplet size is visible in a T-junction fluidic channel since after applying voltages, specified with non-dimensional electrowetting numbers of ?=0.5 and 1.2, dispersed phase is pulled out into the oil phase. In fact, with applying the voltage on the top wall, the droplet breakup time was decreased and smaller droplets were produced. Finally, different important parameters such as pressure difference across the interface as well as Shear Stress exerted from the continuous phase shear stress were examined in a detail.

PREDICTION OF UNSTEADY STATES IN LID-DRIVEN CAVITIES FILLED WITH AN INCOMPRESSIBLE VISCOUS FLUID

2012 ◽  
Vol 23 (04) ◽  
pp. 1250030 ◽  
Author(s):  
FAYÇAL HAMMAMI ◽  
NADER BEN-CHEIKH ◽  
ANTONIO CAMPO ◽  
BRAHIM BEN-BEYA ◽  
TAIEB LILI
Keyword(s):  
Reynolds Number ◽  
Numerical Study ◽  
Three Dimensional ◽  
Staggered Grid ◽  
Three Dimensional Flow ◽  
Driven Cavity ◽  
Flow Evolution ◽  
2D And 3D ◽  
Benchmark Solutions ◽  
Good Agreement

In this work, a numerical study devoted to the two-dimensional and three-dimensional flow of a viscous, incompressible fluid inside a lid-driven cavity is undertaking. All transport equations are solved using the finite volume formulation on a staggered grid system and multi-grid acceleration. Quantitative aspects of two and three-dimensional flows in a lid-driven cavity for Reynolds number Re = 1000 show good agreement with benchmark results. An analysis of the flow evolution demonstrates that, with increments in Re beyond a certain critical value Rec, the steady flow becomes unstable and bifurcates into unsteady flow. It is observed that the transition from steadiness to unsteadiness follows the classical Hopf bifurcation. The time-dependent velocity distribution is studied in detail and the critical Reynolds number is localized for both 2D and 3D cases. Benchmark solutions for 2D and 3D lid-driven cavity flows are performed for Re = 1500 and 6000.

Application of Two Phase Eulerian CFD Model to Simulate High Velocity Jet Induced Scour

2020 ◽  
Author(s):  
Nicholas S. Tavouktsoglou ◽  
Aggelos Dimakopoulos ◽  
Jeremy Spearman ◽  
Richard J. S. Whitehouse
Keyword(s):  
Numerical Model ◽  
High Velocity ◽  
Stokes Equations ◽  
Solid Phase ◽  
Three Dimensional ◽  
Water Jet ◽  
Ocean Engineering ◽  
Two Phase ◽  
Water Jets ◽  
Good Agreement

Abstract Submerged water jet causing soil excavation is a typical water-soil interaction process that occurs widely in many engineering disciplines. In hydraulic engineering for instance, a typical example would be scour downstream of headcuts, culverts, or dam spillways. In port and waterway engineering, erosion of the channel bed or quay wall by the propellers of passing ships are also typical water jet/soil interaction problems. In ocean engineering, trenching by impinging high-velocity water jets has been used as an efficient method for cable and pipeline burial. At present, physical modelling and simple prediction equations have been the main practical engineering tool for evaluating scour in these situations. However, with the increasing computational power of modern computers and the development of new Computational Fluid Dynamics (CFD) solvers, scour prediction in such engineering problems has become possible. In the present work three-dimensional (3D) numerical modelling has been applied to reproduce the capability of a pair of water jets to backfill an excavated trench. The simulations are carried out using a state-of-the-art three-dimensional Eulerian two-phase scour model based on the open source CFD software OpenFOAM. The fluid phase is resolved by solving modified Navier-Stokes equations, which take into consideration the influence of the solid phase, i.e., the soil particles. This paper first presents a validation of the numerical model against vertical jet erosion tests from the literature and conducted at HR Wallingford. The results of the model show good agreement with the experimental tests, with the numerical model predicting the scour hole depth and extent with good accuracy. The paper then presents a validation of the model’s ability to reproduce deposition which is evaluated through a comparison with settling velocity data and empirical formulations found in literature, again with the model showing good agreement. Finally, the model is applied to a prototype cable burial problem using a commercially available controlled flow jet excavator. The study found that the use of water jets can be effective (subject to confirmation of the time-scale required for real operations) for performing backfill operations but that the effectiveness is closely related to the type of sediment and selection of an appropriate jet discharge. As a result, in order for the water jet method to be effective for backfill, there is a requirement for a good description of the variation in sediment type along the trench and a requirement for the jet discharge to be varied as different sediment types are encountered.

scholarly journals Heat Transfer Enhancement and Hydrodynamic Characteristics of Nanofluid in Turbulent Flow Regime

2015 ◽  
Vol 2015 ◽  
pp. 1-6 ◽  
Author(s):  
Mohammad Nasiri-lohesara
Keyword(s):  
Heat Transfer ◽  
Numerical Study ◽  
Pure Water ◽  
Reynolds Numbers ◽  
Hydrodynamic Characteristics ◽  
Two Phase ◽  
Tube Heat Exchanger ◽  
Turbulent Flow Regime ◽  
Lower Slope ◽  
Good Agreement

Turbulent forced convection ofγ-Al2O3/water nanofluid in a concentric double tube heat exchanger has been investigated numerically using mixture two-phase model. Nanofluids are used as coolants flowing in the inner tube while hot pure water flows in outer tube. The studies are conducted for Reynolds numbers ranging from 20,000 to 50,000 and nanoparticle volume fractions of 2, 3, 4, and 6 percent. Results showed that nanofluid has no effects on fully developed length and average heat transfer coefficient enhances with lower slope than wall shear stress. Comparisons with experimental correlation in literature are conducted and good agreement with present numerical study is achieved.

Numerical Study of Three-Dimensional Oscillatory Natural Convection at Low Prandtl Number in Rectangular Enclosures

2000 ◽  
Vol 123 (1) ◽  
pp. 77-83 ◽  
Author(s):  
Shunichi Wakitani
Keyword(s):  
Natural Convection ◽  
Prandtl Number ◽  
Numerical Study ◽  
Three Dimensional ◽  
Width Ratio ◽  
Three Dimensional Flow ◽  
Longitudinal Vortices ◽  
Aspect Ratios ◽  
Vertical Walls ◽  
Prandtl Numbers

Numerical investigations are presented for three-dimensional natural convection at low Prandtl numbers (Pr) from 0 to 0.027 in rectangular enclosures with differentially heated vertical walls. Computations are carried out for the enclosures with aspect ratios (length/height) 2 and 4, and width ratios (width/height) ranging from 0.5 to 4.2. Dependence of the onset of oscillation on the Prandtl number, the aspect ratio, and the width ratio is investigated. Furthermore, oscillatory, three-dimensional flow structure is clarified. The structure is characterized by some longitudinal vortices (rolls) as well as cellular pattern.

Sign in / Sign up

Export Citation Format

Share Document