Experimental and Computational Investigation of Heat Transfer Effectiveness and Pressure Distribution of a Shrouded Blade Tip Section

2004 ◽  
Author(s):  
Nirm V. Nirmalan ◽  
Jeremy C. Bailey ◽  
Mark E. Braaten
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Pressure Distribution ◽  
Coolant Flow ◽  
Tip Clearance ◽  
Computational Investigation ◽  
Blade Tip ◽  
Flow Through ◽  
Tip Shroud ◽  
Unique Study

An experimental and computational investigation was conducted to study the detailed distribution of heat transfer effectiveness and pressure on an attached tip-shroud of a turbine blade. Temperatures and pressures were measured on the airfoil-side and gap-side surfaces of the shrouded tip in a three-airfoil stationary cascade. The instrumented center airfoil and the two slave airfoils modeled the aerodynamic tip section of a blade and have the capability to vary tip clearance. The experiments were run at gaps varying of 0.25% to 1.67% of blade span and at an airfoil exit Reynolds number of 1.26×106 and Mach number of 0.95. The effect of coolant flow through the radial-cooled airfoil was also studied. The experimental results are compared with a computational model using the commercially available code, CFX. This unique study presents the influence of gap and coolant flow on the pressure distribution and heat transfer effectiveness of an attached tip-shroud surface.

Flow and Heat Transfer in Turbine Tip Gaps

1989 ◽  
Vol 111 (3) ◽  
pp. 301-309 ◽  
Author(s):  
J. Moore ◽  
J. G. Moore ◽  
G. S. Henry ◽  
U. Chaudhry
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
High Reynolds Number ◽  
Reynolds Numbers ◽  
Large Separation ◽  
Flow And Heat Transfer ◽  
Blade Tip ◽  
Flow Through ◽  
High Mach ◽  
High Reynolds

The effects of Reynolds number on flow through a tip gap are investigated by performing laminar flow calculations for an idealized two-dimensional tip gap geometry. The results of the calculations aid in understanding and reconciliation of low Much number turbine tip gap measurements, which range in tip gap Reynolds number from 100 to 10,000. For the higher Reynolds numbers, both the calculations and the measurements show a large separation off the sharp edge of the blade tip corner. For a high Reynolds number, fully turbulent flow calculations were also made. These also show a large separation and the results are compared with heat transfer measurements. At high Mach numbers, there are complex shock structures in the tip gap. These are modeled experimentally using a water table.

Experimental Investigation of Aerodynamic Losses of Different Shapes of a Shrouded Blade Tip Section

2005 ◽  
Author(s):  
Nirm V. Nirmalan ◽  
Jeremy C. Bailey
Keyword(s):  
Experimental Investigation ◽  
Reynolds Number ◽  
Mach Number ◽  
Tip Clearance ◽  
Exit Plane ◽  
Airfoil Surface ◽  
Blade Tip ◽  
Different Shapes ◽  
Tip Shroud ◽  
Aerodynamic Losses

An experimental investigation was conducted to study the effects on aerodynamic losses of different tip shroud shapes of a shrouded turbine blade. Pressures were measured on the airfoil surface near the tip and a plane downstream of the exit plane in a three-airfoil stationary cascade. The instrumented center airfoil and the two slave airfoils modeled the aerodynamic tip section of a blade and have the capability to vary tip clearance. The experiments were run at tip-clearances varying from 0.25% to 1.67% and at an exit Reynolds number of 1.25 × 106 and Mach Number of 0.95. The paper presents the influence of three tip-shroud shapes and five different tip-clearances on the aerodynamic losses.

Influence of tip clearance and cavity depth on heat transfer in a cutback squealer tip

2020 ◽  
pp. 095441002096469
Author(s):  
Weijie Wang ◽  
Shaopeng Lu ◽  
Hongmei Jiang ◽  
Qiusheng Deng ◽  
Jinfang Teng ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Suction Side ◽  
High Heat ◽  
Tip Clearance ◽  
Tip Leakage Flow ◽  
Trailing Edge ◽  
Cavity Depth ◽  
High Heat Transfer ◽  
Blade Tip ◽  
High Heat Transfer Coefficient

Numerical simulations are conducted to present the aerothermal performance of a turbine blade tip with cutback squealer rim. Two different tip clearance heights (0.5%, 1.0% of the blade span) and three different cavity depths (2.0%, 3.0%, and 6.0% of the blade span) are investigated. The results show that a high heat transfer coefficient (HTC) strip on the cavity floor appears near the suction side. It extends with the increase of tip clearance height and moves towards the suction side with the increase of cavity depth. The cutback region near the trailing edge has a high HTC value due to the flush of over-tip leakage flow. High HTC region shrinks to the trailing edge with the increase of cavity depth since there is more accumulated flow in the cavity for larger cavity depth. For small tip clearance cases, high HTC distribution appears on the pressure side rim. However, high HTC distribution is observed on suction side rim for large tip clearance height. This is mainly caused by the flow separation and reattachment on the squealer rims.

Numerical Modeling of Heat Transfer and Pressure Losses for Uncooled Gas Turbine Blade Tip: Effect of Tip Clearance and Tip Geometry

2007 ◽  
Author(s):  
Lamyaa A. El-Gabry
Keyword(s):  
Heat Transfer ◽  
Mach Number ◽  
Gas Turbine ◽  
Computational Study ◽  
Numerical Models ◽  
Pressure Ratio ◽  
Tip Clearance ◽  
Pressure Losses ◽  
Blade Tip ◽  
Exit Mach Number

A computational study has been performed to predict the heat transfer distribution on the blade tip surface for a representative gas turbine first stage blade. CFD predictions of blade tip heat transfer are compared to test measurements taken in a linear cascade, when available. The blade geometry has an inlet Mach number of 0.3 and an exit Mach number of 0.75, pressure ratio of 1.5, exit Reynolds number based on axial chord of 2.57×106, and total turning of 110 deg. Three blade tip configurations were considered; they are flat tip, a full perimeter squealer, and an offset squealer where the rim is offset to the interior of the tip perimeter. These three tip geometries were modeled at three tip clearances of 1.25, 2.0, and 2.75% of blade span. The tip heat transfer results of the numerical models agree fairly well with the data and are comparable to other CFD predictions in the open literature.

Measurements of the Tip Clearance Flow for a High-Reynolds-Number Axial-Flow Rotor

1995 ◽  
Vol 117 (4) ◽  
pp. 522-532 ◽  
Author(s):  
W. C. Zierke ◽  
K. J. Farrell ◽  
W. A. Straka
Keyword(s):  
Reynolds Number ◽  
Flow Visualization ◽  
Vortex Core ◽  
Rotor Blade ◽  
High Reynolds Number ◽  
Tip Clearance ◽  
Tip Leakage Vortex ◽  
Tip Leakage ◽  
Blade Tip ◽  
High Reynolds

A high-Reynolds-number pump (HIREP) facility has been used to acquire flow measurements in the rotor blade tip clearance region, with blade chord Reynolds numbers of 3,900,000 and 5,500,000. The initial experiment involved rotor blades with varying tip clearances, while a second experiment involved a more detailed investigation of a rotor blade row with a single tip clearance. The flow visualization on the blade surface and within the flow field indicate the existence of a trailing-edge separation vortex, a vortex that migrates radially upward along the trailing edge and then turns in the circumferential direction near the casing, moving in the opposite direction of blade rotation. Flow visualization also helps in establishing the trajectory of the tip leakage vortex core and shows the unsteadiness of the vortex. Detailed measurements show the effects of tip clearance size and downstream distance on the structure of the rotor tip leakage vortex. The character of the velocity profile along the vortex core changes from a jetlike profile to a wakelike profile as the tip clearance becomes smaller. Also, for small clearances, the presence and proximity of the casing endwall affects the roll-up, shape, dissipation, and unsteadiness of the tip leakage vortex. Measurements also show how much circulation is retained by the blade tip and how much is shed into the vortex, a vortex associated with high losses.

scholarly journals Numerical Calculation of Flow for Cascade With Tip Clearance

1994 ◽  
Author(s):  
Shimpei Mizuki ◽  
Hoshio Tsujita
Keyword(s):  
Three Dimensional ◽  
Tip Clearance ◽  
Turbine Cascade ◽  
Governing Equations ◽  
Tensor Form ◽  
Pressure Surface ◽  
Rear Part ◽  
Blade Tip ◽  
Flow Through ◽  
Blade Tip Geometry

Three-dimensional incompressible turbulent flow within a linear turbine cascade with tip clearance is analyzed numerically. The governing equations involving the standard k-ε model are solved in the physical component tensor form with a boundary-fitted coordinate system. In the analysis, the blade tip geometry is treated accurately in order to predict the flow through the tip clearance in detail when the blades have large thicknesses. Although the number of grids employed in the present study is not enough because of the limitation of computer storage memory, the computed results show good agreements with the experimental results. Moreover, the results clearly exhibit the locus of minimum pressure on the rear part of the pressure surface at the blade tip.

scholarly journals Effects of Tip Clearance Gap and Exit Mach Number on Turbine Blade Tip and Near-Tip Heat Transfer

2013 ◽  
Author(s):  
K. Anto ◽  
S. Xue ◽  
W. F. Ng ◽  
L. J. Zhang ◽  
H. K. Moon
Keyword(s):  
Heat Transfer ◽  
Mach Number ◽  
Turbine Blade ◽  
Leading Edge ◽  
Suction Side ◽  
Tip Clearance ◽  
Pressure Side ◽  
Engine Blade ◽  
Blade Tip ◽  
Exit Mach Number

This study focuses on local heat transfer characteristics on the tip and near-tip regions of a turbine blade with a flat tip, tested under transonic conditions in a stationary, 2-D linear cascade with high freestream turbulence. The experiments were conducted at the Virginia Tech transonic blow-down wind tunnel facility. The effects of tip clearance and exit Mach number on heat transfer distribution were investigated on the tip surface using a transient infrared thermography technique. In addition, thin film gages were used to study similar effects in heat transfer on the near-tip regions at 94% height based on engine blade span of the pressure and suction sides. Surface oil flow visualizations on the blade tip region were carried-out to shed some light on the leakage flow structure. Experiments were performed at three exit Mach numbers of 0.7, 0.85, and 1.05 for two different tip clearances of 0.9% and 1.8% based on turbine blade span. The exit Mach numbers tested correspond to exit Reynolds numbers of 7.6 × 105, 9.0 × 105, and 1.1 × 106 based on blade true chord. The tests were performed with a high freestream turbulence intensity of 12% at the cascade inlet. Results at 0.85 exit Mach showed that an increase in the tip gap clearance from 0.9% to 1.8% translates into a 3% increase in the average heat transfer coefficients on the blade tip surface. At 0.9% tip clearance, an increase in exit Mach number from 0.85 to 1.05 led to a 39% increase in average heat transfer on the tip. High heat transfer was observed on the blade tip surface near the leading edge, and an increase in the tip clearance gap and exit Mach number augmented this near-leading edge tip heat transfer. At 94% of engine blade height on the suction side near the tip, a peak in heat transfer was observed in all test cases at s/C = 0.66, due to the onset of a downstream leakage vortex, originating from the pressure side. An increase in both the tip gap and exit Mach number resulted in an increase, followed by a decrease in the near-tip suction side heat transfer. On the near-tip pressure side, a slight increase in heat transfer was observed with increased tip gap and exit Mach number. In general, the suction side heat transfer is greater than the pressure side heat transfer, as a result of the suction side leakage vortices.

scholarly journals Influences of Tip Cooling Injection on Tip Clearance Control at Design and Off-Design Incidences

2009 ◽  
Vol 2009 ◽  
pp. 1-12 ◽  
Author(s):  
Maosheng Niu ◽  
Shusheng Zang
Keyword(s):  
Heat Transfer ◽  
Tip Clearance ◽  
Air Injection ◽  
Turbine Cascade ◽  
Tip Clearance Flow ◽  
Clearance Flow ◽  
Blade Tip ◽  
Design Value ◽  
Tip Injection ◽  
Clearance Control

A numerical investigation has been performed to study the influences of cooling injection from the blade tip surface on controlling tip clearance flow in an unshrouded, high-turning axial turbine cascade. Emphasis is put on the analysis of the effectiveness of tip injection when the approaching flow is at design and off-design incidences. A total of three incidence angles are investigated, 7.4°, 0°, 0°, 0°, and 7.6°, 0° relative to the design value. The results indicate that even at the off-design incidences, tip injection can also act as an obstruction to the tip clearance flow and weaken the interaction between the passage flow and the tip clearance flow. It is also found that tip injection causes the tip clearance loss to be less sensitive to the incidences. Moreover, with injection, at all these incidences the heat transfer conditions are improved significantly on the blade tip surface in the middle and aft parts of blade. Thus, tip injection is proved to be an effective method of controlling tip clearance flow, even at off-design conditions. Beside that, an indirect empirical correlation is observed to be able to perform well in predicting the losses induced by tip clearance flow at design and off-design conditions, no matter whether air injection is active or not.

Effect of Rounded Corners on Heat Transfer and Fluid Flow Through Triangular Duct

2018 ◽  
Vol 140 (12) ◽  
Author(s):  
Rajneesh Kumar ◽  
Anoop Kumar ◽  
Varun Goel
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Curvature Radius ◽  
Cross Sectional ◽  
Close Match ◽  
Lower Reynolds Number ◽  
Flow Heat ◽  
Flow Through ◽  
Experimental Findings ◽  
Sharp Corners

Turbulent flow heat transfer and friction penalty in triangular cross-sectional duct is studied in the present paper. The sharp corners of the duct are modified by converting it into circular shape. Five different models were designed and fabricated. Heat transfer through all the models was investigated and compared conventional triangular duct under similar conditions. The curvature radius of rounded corners for different models was kept constant (0.33 times the duct height). The numerical simulations were also performed and the obtained result validated with the experimental findings and close match observed between them. The velocity and temperature distribution is analyzed at particular location in the different models. Because of rounded corners, higher velocity is observed inside the duct (except corners) compared to conventional duct. Considerable increase in Nusselt number is seen in model-5, model-4, model-3, and model-2 by 191%, 41%, 19%, and 8% in comparison to model-1, respectively, at higher Reynolds number (i.e., 17,500). But, frictional penalty through the model-5, model-4, model-3, and model-2 increased by 287%, 54%, 18%, and 12%, respectively, in comparison to model-1 at lower Reynolds number (i.e., 3600).

Sign in / Sign up

Export Citation Format

Share Document