Pressure Gain Combustion Application to Marine and Industrial Gas Turbines

2012 ◽  
Author(s):  
Philip H. Snyder ◽  
M. Razi Nalim
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Technology Development ◽  
Innovative Technology ◽  
Turbine Engines ◽  
Specific Work ◽  
Compression Pressure ◽  
Pressure Gain Combustion ◽  
Industrial Gas Turbines ◽  
Incremental Improvement

Renewed interest in pressure gain combustion applied as a replacement of conventional combustors within gas turbine engines creates the potential for greatly increased capability engines in the marine power market segment. A limited analysis has been conducted to estimate the degree of improvements possible in engine thermal efficiency and specific work for a type of wave rotor device utilizing these principles. The analysis considers a realistic level of component losses. The features of this innovative technology are compared with those of more common incremental improvement types of technology for the purpose of assessing potentials for initial market entry within the marine gas turbine market. Both recuperation and non-recuperation cycles are analyzed. Specific fuel consumption improvements in excess of 35% over those of a Brayton cycle are indicated. The technology exhibits the greatest percentage potential in improving efficiency for engines utilizing relatively low or moderate mechanical compression pressure ratios. Specific work increases are indicated to be of an equally dramatic magnitude. The advantages of the pressure gain combustion approach are reviewed as well as its technology development status.

Technological Trend of Aircraft Gas Turbines and its Effect on the Development for Ship Propulsion Plants

1970 ◽  
Author(s):  
N. K. H. Scholz
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Pressure Ratio ◽  
Gas Turbine Engine ◽  
Design Parameters ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Compression Pressure ◽  
Turbine Engine ◽  
Ship Propulsion

The effect of the main design parameters of the aero gas turbine engine cycle, namely combustion temperature and compression pressure ratio, on the specific performance values is discussed. The resulting development trend has been of essential influence on the technology. Relevant approaches are outlined. The efforts relating to weight and manufacturing expense are also indicated. In the design of aero gas turbine engines increasing consideration is given to the specific flight mission requirements, such as for instance by the introduction of the by-pass principle. Therefore direct application of aero gas turbine engines for ship propulsion without considerable modifications, as has been practiced in the past, is not considered very promising for the future. Nevertheless, there are possibilities to take advantage of aero gas turbine engine developments for ship propulsion systems. Appropriate approaches are discussed. With the experience obtained from aero gas turbine engines that will enter service in the early seventies it should be possible to develop marine gas turbine engines achieving consumptions and lifes that are competitive with those of advanced diesel units.

scholarly journals Development of High Efficient Industrial Gas Turbine Engines Based on NK-Series Aeroengine Family

1991 ◽  
Author(s):  
N. D. Kuznetsov ◽  
V. N. Orlov ◽  
K. V. Kahovsky
Keyword(s):  
Gas Turbine ◽  
Thermal Efficiency ◽  
Gas Turbines ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
High Efficient ◽  
Industrial Gas Turbines ◽  
Industrial Gas Turbine

The paper gives principles of aeroengines conversion into industrial gas turbines. New constructive solutions for designing gas turbines with thermal efficiency 38% are discussed. Data are based on KSPA “TRUD” experience of NK-12 and NK-8 aeroengines conversion.

scholarly journals Benefits and Challenges of Pressure-Gain Combustion Systems for Gas Turbines

2009 ◽  
Vol 131 (03) ◽  
pp. 54-55 ◽  
Author(s):  
Chris Brophy ◽  
Gabriel Roy
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Technology Development ◽  
Combustion Process ◽  
Annular Array ◽  
Steady State Operation ◽  
Pressure Gain Combustion ◽  
Combustion Systems ◽  
And Performance ◽  
Collaborative Efforts

This article discusses benefits and challenges of Pressure-Gain Combustion Systems for Gas Turbines. The article also highlights that one approach to substantially improve gas turbine thermal efficiency is to replace the nearly constant pressure combustion process with some form of pressure-gain heat release such as either a constant volume or detonative mode of combustion. These systems commonly possess some form of rotating inlet valve design to control the filling process for an annular array of combustors and maintain the appropriate amount of inlet isolation. Although evaluation of turbine life and performance needs to continue, turbine efficiencies approaching values comparable to those of steady-state operation have been reported. The article concludes that the collaborative efforts, such as listed in the article, are ultimately required in times of reduced funding for continued technology development. Even with the risks and challenges associated with this technology, a high payoff potential exists with hybrid gas turbine architectures.

scholarly journals Progress in Novel Electrodeposited Bond Coats for Thermal Barrier Coating Systems

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4214
Author(s):  
Kranthi Kumar Maniam ◽  
Shiladitya Paul
Keyword(s):  
Gas Turbine ◽  
Thermal Barrier Coating ◽  
Gas Turbines ◽  
High Performance ◽  
Turbine Engines ◽  
Thermal Barrier ◽  
Gas Turbine Engines ◽  
Potential Cost ◽  
Bond Coats ◽  
Barrier Coating

The increased demand for high performance gas turbine engines has resulted in a continuous search for new base materials and coatings. With the significant developments in nickel-based superalloys, the quest for developments related to thermal barrier coating (TBC) systems is increasing rapidly and is considered a key area of research. Of key importance are the processing routes that can provide the required coating properties when applied on engine components with complex shapes, such as turbine vanes, blades, etc. Despite significant research and development in the coating systems, the scope of electrodeposition as a potential alternative to the conventional methods of producing bond coats has only been realised to a limited extent. Additionally, their effectiveness in prolonging the alloys’ lifetime is not well understood. This review summarises the work on electrodeposition as a coating development method for application in high temperature alloys for gas turbine engines and discusses the progress in the coatings that combine electrodeposition and other processes to achieve desired bond coats. The overall aim of this review is to emphasise the role of electrodeposition as a potential cost-effective alternative to produce bond coats. Besides, the developments in the electrodeposition of aluminium from ionic liquids for potential applications in gas turbines and the nuclear sector, as well as cost considerations and future challenges, are reviewed with the crucial raw materials’ current and future savings scenarios in mind.

scholarly journals Comprehensive Thermodynamic Analysis of the Humphrey Cycle for Gas Turbines with Pressure Gain Combustion

Energies ◽  
2018 ◽  
Vol 11 (12) ◽  
pp. 3521 ◽  
Author(s):  
Panagiotis Stathopoulos
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Combustion Process ◽  
Ideal Gas ◽  
Point Of View ◽  
Pressure Gain Combustion ◽  
Combustion Technology ◽  
Secondary Air ◽  
And Performance ◽  
The Impact

Conventional gas turbines are approaching their efficiency limits and performance gains are becoming increasingly difficult to achieve. Pressure Gain Combustion (PGC) has emerged as a very promising technology in this respect, due to the higher thermal efficiency of the respective ideal gas turbine thermodynamic cycles. Up to date, only very simplified models of open cycle gas turbines with pressure gain combustion have been considered. However, the integration of a fundamentally different combustion technology will be inherently connected with additional losses. Entropy generation in the combustion process, combustor inlet pressure loss (a central issue for pressure gain combustors), and the impact of PGC on the secondary air system (especially blade cooling) are all very important parameters that have been neglected. The current work uses the Humphrey cycle in an attempt to address all these issues in order to provide gas turbine component designers with benchmark efficiency values for individual components of gas turbines with PGC. The analysis concludes with some recommendations for the best strategy to integrate turbine expanders with PGC combustors. This is done from a purely thermodynamic point of view, again with the goal to deliver design benchmark values for a more realistic interpretation of the cycle.

Design, Development and Application of Vehicle Gas Turbine Engines

1966 ◽  
Vol 181 (1) ◽  
pp. 149-172
Author(s):  
P. A. Phillips ◽  
Peter Spear
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Low Cost ◽  
Engine Performance ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Design Development ◽  
Turbine Engine ◽  
Wide Range ◽  
Cycle Temperature

After briefly summarizing worldwide automotive gas turbine activity, the paper analyses the power plant requirements of a wide range of vehicle applications in order to formulate the design criteria for acceptable vehicle gas turbines. Ample data are available on the thermodynamic merits of various gas turbine cycles; however, the low cost of its piston engine competitor tends to eliminate all but the simplest cycles from vehicle gas turbine considerations. In order to improve the part load fuel economy, some complexity is inevitable, but this is limited to the addition of a glass ceramic regenerator in the 150 b.h.p. engine which is described in some detail. The alternative further complications necessary to achieve satisfactory vehicle response at various power/weight ratios are examined. Further improvement in engine performance will come by increasing the maximum cycle temperature. This can be achieved at lower cost by the extension of the use of ceramics. The paper is intended to stimulate the design application of the gas turbine engine.

A Comparison Between ORC and Supercritical CO2 Bottoming Cycles For Energy Recovery From Industrial Gas Turbines Exhaust Gas

2021 ◽  
Author(s):  
M. A. Ancona ◽  
M. Bianchi ◽  
L. Branchini ◽  
A. De Pascale ◽  
F. Melino ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Thermal Efficiency ◽  
Gas Turbines ◽  
Supercritical Co2 ◽  
Energy Demand ◽  
Oil And Gas ◽  
Gas Production ◽  
Medium Size ◽  
Oil And Gas Production ◽  
Industrial Gas Turbines

Abstract Gas turbines are often employed in the industrial field, especially for remote generation, typically required by oil and gas production and transport facilities. The huge amount of discharged heat could be profitably recovered in bottoming cycles, producing electric power to help satisfying the onerous on-site energy demand. The present work aims at systematically evaluating thermodynamic performance of ORC and supercritical CO2 energy systems as bottomer cycles of different small/medium size industrial gas turbine models, with different power rating. The Thermoflex software, providing the GT PRO gas turbine library, has been used to model the machines performance. ORC and CO2 systems specifics have been chosen in line with industrial products, experience and technological limits. In the case of pure electric production, the results highlight that the ORC configuration shows the highest plant net electric efficiency. The average increment in the overall net electric efficiency is promising for both the configurations (7 and 11 percentage points, respectively if considering supercritical CO2 or ORC as bottoming solution). Concerning the cogenerative performance, the CO2 system exhibits at the same time higher electric efficiency and thermal efficiency, if compared to ORC system, being equal the installed topper gas turbine model. The ORC scarce performance is due to the high condensing pressure, imposed by the temperature required by the thermal user. CO2 configuration presents instead very good cogenerative performance with thermal efficiency comprehended between 35 % and 46 % and the PES value range between 10 % and 22 %. Finally, analyzing the relationship between capital cost and components size, it is estimated that the ORC configuration could introduce an economical saving with respect to the CO2 configuration.

Development and Integration of the Dual Fuel Combustion System for the MGT Gas Turbine Family

2021 ◽  
Author(s):  
Bernhard Ćosić ◽  
Frank Reiss ◽  
Marc Blümer ◽  
Christian Frekers ◽  
Franklin Genin ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Distribution System ◽  
Gas Turbines ◽  
Liquid Fuel ◽  
Fuel Injection ◽  
Liquid Fuels ◽  
Dual Fuel ◽  
Gaseous Fuels ◽  
Supply And Distribution ◽  
Industrial Gas Turbines

Abstract Industrial gas turbines like the MGT6000 are often operated as power supply or as mechanical drives. In these applications, liquid fuels like 'Diesel Fuel No.2' can be used either as main fuel or as backup fuel if natural gas is not reliably available. The MAN Gas Turbines (MGT) operate with the Advanced Can Combustion (ACC) system, which is capable of ultra-low NOx emissions for gaseous fuels. This system has been further developed to provide dry dual fuel capability. In the present paper, we describe the design and detailed experimental validation process of the liquid fuel injection, and its integration into the gas turbine package. A central lance with an integrated two-stage nozzle is employed as a liquid pilot stage, enabling ignition and start-up of the engine on liquid fuel only. The pilot stage is continuously operated, whereas the bulk of the liquid fuel is injected through the premixed combustor stage. The premixed stage comprises a set of four decentralized nozzles based on fluidic oscillator atomizers, wherein atomization of the liquid fuel is achieved through self-induced oscillations. We present results illustrating the spray, hydrodynamic, and emission performance of the injectors. Extensive testing of the burner at atmospheric and full load high-pressure conditions has been performed, before verification within full engine tests. We show the design of the fuel supply and distribution system. Finally, we discuss the integration of the dual fuel system into the standard gas turbine package of the MGT6000.

Determination of Cycle Configuration of Gas Turbines and Aircraft Engines by Optimization Procedure

1990 ◽  
Author(s):  
Yoshiharu Tsujikawa ◽  
Makoto Nagaoka
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Specific Impulse ◽  
Optimization Procedure ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Aircraft Engines ◽  
Scramjet Engine ◽  
Aero Engines

This paper is devoted to the analyses and optimization of simple and sophisticated cycles, particularly for various gas turbine engines and aero-engines (including scramjet engine) to achive the maximum performance. The optimization of such criteria as thermal efficiency, specific output and total performance for gas turbine engines, and overall efficiency, non-dimensional thrust and specific impulse for aero-engines have been performed by the optimization procedure with multiplier method. The comparisons of results with analytical solutions establishes the validity of the optimization procedure.

Design Parameters Prediction of New Type Gas Turbine Based on a Hybrid GRA-SVM Prediction Model

2017 ◽  
Author(s):  
Tingting Wei ◽  
Dengji Zhou ◽  
Jinwei Chen ◽  
Yaoxin Cui ◽  
Huisheng Zhang
Keyword(s):  
Prediction Model ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Technology Development ◽  
Design Parameters ◽  
Support Vector ◽  
Performance Parameters ◽  
New Type ◽  
Equipment Manufacture ◽  
Grey Relational

Since the late 1930s, gas turbine has begun to develop rapidly. To improve the economic and safety of gas turbine, new types were generated frequently by Original Equipment Manufacture (OEM). In this paper, a hybrid GRA-SVM prediction model is established to predict the main design parameters of new type gas turbines, based on the combination of Grey Relational Analysis (GRA) and Support Vector Machine (SVM). The parameters are classified into two types, system performance parameters reflecting market demands and technology development, and component performance parameters reflecting technology development and coupling connections. The regularity based on GRA determines the prediction order, then new type gas turbine parameters can be predicted with known system parameters. The model is verified by the application to SGT600. In this way, the evolution rule can be obtained with the development of gas turbine technology, and the improvement potential of several components can be predicted which will provide supports for overall performance design.

Sign in / Sign up

Export Citation Format

Share Document