Vortices and Performance of Internal and External Volutes

2015 ◽  
Author(s):  
Hua Chen ◽  
Ding Tong ◽  
Xiaochun Wang
Keyword(s):  
Numerical Simulation ◽  
Shear Stress ◽  
Cross Section ◽  
Centrifugal Compressor ◽  
Cross Flow ◽  
Cross Sectional ◽  
Compressor Performance ◽  
And Performance ◽  
Sectional Shape ◽  
Different Levels

In this paper, the cross flow in several internal and external volutes of a small centrifugal compressor is examined to highlight its effects on compressor performance. Different levels of the loss associated with shear stress related to the vortices in the volute cross section are shown to be the reason behind the diverse performance of internal volutes and external volutes. A numerical simulation is carried out to substantiate this and to further study this effect of cross sectional shape of volutes.

Geometric Design of Rectangular Cross-Sectional Springs

2018 ◽  
Vol 920 ◽  
pp. 126-131
Author(s):  
Yeong Maw Hwang ◽  
D.S. Lin ◽  
Sheng Liang Lin
Keyword(s):  
Shear Stress ◽  
Cross Section ◽  
Maximum Shear Stress ◽  
Cross Sectional Area ◽  
Sectional Area ◽  
Rectangular Section ◽  
Cross Sectional ◽  
Short Side ◽  
The Cross ◽  
Sectional Shape

In order to study the influence of the cross-sectional shape on the stiffness of a spring, a finite element analysis software DEFORM is used to simulate and analyze the torsion of rectangular cross-section bars. The material of the bar is TS1800 SAE9254 and the cross-section of aspect ratio (w / h) is 1.5. From literature it is known that when the rectangular section bar is twisted, the shear stress at the four corners is zero, so elliptical corners can decrease the volume and increase the stiffness with the same volume. Five levels for the long side of the elliptical corner are set as 1 to 5 mm, and 3 levels are set for the short side. Torsion of the rectangular section bars under 15 kinds of geometric designs are simulated to find the preferred cross-sectional shape design by evaluating the cross-sectional area, load, and the maximum shear stress. The objective of the design is obtaining a uniform stress distribution with a larger spring stiffness and lighter weight. The optimal cross section of the bars is established as the spring geometry, and the pre-loading processing of the spring is simulated. The required load and the maximum shear stress data are obtained. The effects of load, cross-sectional area and maximum shear stress on the springs performance are investigated.

Automated 3D measurement of fiber cross section morphology in handsheets

2012 ◽  
Vol 27 (2) ◽  
pp. 264-269 ◽  
Author(s):  
Christian Lorbach ◽  
Ulrich Hirn ◽  
Johannes Kritzinger ◽  
Wolfgang Bauer
Keyword(s):  
Image Analysis ◽  
Cross Section ◽  
Cross Sections ◽  
Image Plane ◽  
3D Measurement ◽  
Cross Sectional ◽  
Fiber Cross Section ◽  
Fiber Wall ◽  
Sectional Shape ◽  
Cross Section Geometry

Abstract We present a method for 3D measurement of fiber cross sectional morphology from handsheets. An automated procedure is used to acquire 3D datasets of fiber cross sectional images using an automated microtome and light microscopy. The fiber cross section geometry is extracted using digital image analysis. Simple sample preparation and highly automated image acquisition and image analysis are providing an efficient tool to analyze large samples. It is demonstrated that if fibers are tilted towards the image plane the images of fiber cross sections are always larger than the true fiber cross section geometry. In our analysis the tilting angles of the fibers to the image plane are measured. The resulting fiber cross sectional images are distorted to compensate the error due to fiber tilt, restoring the true fiber cross sectional shape. We use an approximated correction, the paper provides error estimates of the approximation. Measurement results for fiber wall thickness, fiber coarseness and fiber collapse are presented for one hardwood and one softwood pulp.

Numerical Investigation of the Effect of Diffuser and Volute Design Parameters on the Performance of a Centrifugal Compressor Stage

2016 ◽  
Author(s):  
Lei Yu ◽  
William T. Cousins ◽  
Feng Shen ◽  
Georgi Kalitzin ◽  
Vishnu Sishtla ◽  
...  
Keyword(s):  
Centrifugal Compressor ◽  
Gas Flow ◽  
Pressure Rise ◽  
Design Parameters ◽  
Compressor Stage ◽  
Flow Distortion ◽  
Cross Sectional ◽  
Centrifugal Stage ◽  
And Performance ◽  
The Impact

In this effort, 3D CFD simulations are carried out for real gas flow in a refrigeration centrifugal compressor. Both commercial and the in-house CFD codes are used for steady and unsteady simulations, respectively. The impact on the compressor performance with various volute designs and diffuser modifications are investigated with steady simulations and the analysis is focused on both the diffuser and the volute loss, in addition to the flow distortion at impeller exit. The influence of the tongue, scroll diffusion ratio, diffuser length, and cross sectional area distribution is examined to determine the impact on size and performance. The comparisons of total pressure loss, static pressure recovery, through flow velocity, and the secondary flow patterns for different volute designs show that the performance of the centrifugal compressor depends upon how well the scroll portion of the volute collects the flow from the impeller and achieves the required pressure rise with minimum flow losses in the overall diffusion process. Finally, the best design is selected based on compressor stage pressure rise and peak efficiency improvement. An unsteady simulation of the full wheel compressor stage was carried out to further examine the interaction of impeller, diffuser and the volute. The unsteady flow interactions are shown to have a major impact on the performance of the centrifugal stage.

scholarly journals An atomic resolution study of precipitates in an Al-Ge Alloy

1986 ◽  
Vol 44 ◽  
pp. 538-539
Author(s):  
U. Dahmen ◽  
C. Nelson ◽  
K.H. Westmacott
Keyword(s):  
Cross Section ◽  
Atomic Resolution ◽  
Face Centered Cubic ◽  
Orientation Relationships ◽  
Cross Sectional ◽  
The Past ◽  
Moiré Fringes ◽  
Typical Aspect ◽  
Face Centered ◽  
Sectional Shape

The difficulty of precipitating germanium in dilute aluminum-germanium alloys is due to a large difference in crystal structures (face-centered cubic and diamond cubic) accompanied by a substantial volume expansion of 36%. A great variety of precipitate morphologies and orientation relationships are observed. A frequently found morphology is that of <100> needles. By selected area diffraction and Moire fringes it has been established that <100> Al and <110> Ge are parallel along the needle axis. The typical aspect ratio of about 100 has made it difficult in the past to investigate the cross-sectional shape and internal structure of these needles, although some indications of internal twinning were found in plates. in the present work, the Berkeley Atomic Resolution Microscope was used to examine needles in cross section by imaging along the <110> Ge <100> Al needle axis.

scholarly journals Optimization of the cross-sectional shape of the belts of trihedral lattice supports

2019 ◽  
Vol 7 (4) ◽  
pp. 5-8
Author(s):  
Linar Sabitov ◽  
Ilnar Baderddinov ◽  
Anton Chepurnenko
Keyword(s):  
Objective Function ◽  
Nonlinear Optimization ◽  
Cross Section ◽  
Optimization Methods ◽  
Cross Sectional ◽  
Maximum Value ◽  
Axial Moment ◽  
The Cross ◽  
Nonlinear Optimization Methods ◽  
Sectional Shape

The article considers the problem of optimizing the geometric parameters of the cross section of the belts of a trihedral lattice support in the shape of a pentagon. The axial moment of inertia is taken as the objective function. Relations are found between the dimensions of the pentagonal cross section at which the objective function takes the maximum value. We introduce restrictions on the constancy of the consumption of material, as well as the condition of equal stability. The solution is performed using nonlinear optimization methods in the Matlab environment.

Numerical study for the improvement of bead spreading architecture with modified nozzle geometries in additive manufacturing of polymers

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Easir Arafat Papon ◽  
Anwarul Haque ◽  
Muhammad Ali Rob Sharif
Keyword(s):  
Free Surface ◽  
Numerical Model ◽  
3D Printing ◽  
Cross Section ◽  
Nozzle Exit ◽  
Cross Sectional ◽  
Content Type ◽  
The Cross ◽  
Viscous Polymer ◽  
Sectional Shape

Purpose This paper aims to develop a numerical model of bead spreading architecture of a viscous polymer in fused filament fabrication (FFF) process with different nozzle geometry. This paper also focuses on the manufacturing feasibility of the nozzles and 3D printing of the molten beads using the developed nozzles. Design/methodology/approach The flow of a highly viscous polymer from a nozzle, the melt expansion in free space and the deposition of the melt on a moving platform are captured using the FLUENT volume of fluid (VOF) method based computational fluid dynamics code. The free surface motion of the material is captured in VOF, which is governed by the hydrodynamics of the two-phase flow. The phases involved in the numerical model are liquid polymer and air. A laminar, non-Newtonian and non-isothermal flow is assumed. Under such assumptions, the spreading characteristic of the polymer is simulated with different nozzle-exit geometries. The governing equations are solved on a regular stationary grid following a transient algorithm, where the boundary between the polymer and the air is tracked by piecewise linear interface construction (PLIC) to reconstruct the free surface. The prototype nozzles were also manufactured, and the deposition of the molten beads on a flatbed was performed using a commercial 3D printer. The deposited bead cross-sections were examined through optical microscopic examination, and the cross-sectional profiles were compared with those obtained in the numerical simulations. Findings The numerical model successfully predicted the spreading characteristics and the cross-sectional shape of the extruded bead. The cross-sectional shape of the bead varied from elliptical (with circular nozzle) to trapezoidal (with square and star nozzles) where the top and bottom surfaces are significantly flattened (which is desirable to reduce the void spaces in the cross-section). The numerical model yielded a good approximation of the bead cross-section, capturing most of the geometric features of the bead with a reasonable qualitative agreement compared to the experiment. The quantitative comparison of the cross-sectional profiles against experimental observation also indicated a favorable agreement. The significant improvement observed in the bead cross-section with the square and star nozzles is the flattening of the surfaces. Originality/value The developed numerical algorithm attempts to address the fundamental challenge of voids and bonding in the FFF process. It presents a new approach to increase the inter-bead bonding and reduce the inter-bead voids in 3D printing of polymers by modifying the bead cross-sectional shape through the modification of nozzle exit-geometry. The change in bead cross-sectional shape from elliptical (circular) to trapezoidal (square and star) cross-section is supposed to increase the contact surface area and inter-bead bonding while in contact with adjacent beads.

Simulasi Perancangan Drainase Muka Tanah pada Bandar Udara Achmad Yani Semarang Sebagai Salah Satu Usaha Pencegahan Banjir

WARTA ARDHIA ◽  
2013 ◽  
Vol 39 (4) ◽  
pp. 305-316
Author(s):  
Ataline Muliasari ◽  
Lupi Wahyuningsih
Keyword(s):  
Surface Water ◽  
Cross Section ◽  
Land Surface ◽  
Drainage Channel ◽  
Water Drainage ◽  
Hydraulic Radius ◽  
Channel Depth ◽  
Cross Sectional ◽  
Surface Drainage ◽  
Sectional Shape

Drainage is defined as surface water drainage, either by gravity or by pump which aims to prevent inundation, maintain and lower the water level im order to avoid the amount of water. Ahmad Yani Airport has a poor drainage systems. Furthermore, land subsidence in Semarang area potential for experiencing flooding when the rainy season with a fairly high rainfall. Based on the results of processing the data showed that it is needed the land surface drainage channel with a cross-sectional shape of a trapezium. When the width of the base of the cross section is 3 meters , then the required channel depth is 3.9 meters with a hydraulic radius is 0.82-meter, and hydraulic depth is 3.05 meters. Drainase didefinisikan sebagai pembuangan air permukaan, baik secara gravitasi maupun dengan pompa yang bertujuan untuk mencegah terjadinya genangan, menjaga dan menurunkan permukaan air sehingga genangan air dapat dihindarkan. Bandar Udara Ahmad Yani dengan kondisi sistem drainase yang kurang baik dan penurunan permukaan tanah di wilayah Semarang, maka bila musim penghujan tiba dengan curah hujan yang cukup tinggi selalu berpotensi untuk mengalami banjir. Berdasarkan hasil pengolahan data juga didapatkan hasil bahwa untuk menyesuaikan antara curah hujan di wilayah Semarang dengan luas area Bandar udara Achmad Yani diperlukan saluran drainase muka tanah berupa saluran dengan bentuk penampang trapezium. Bila lebar dasar dari penampang trapezim tersebut adalah 3 meter, maka diperlukan saluran sedalam 3,9 meter dengan Jari-jari hydraulic 0,82 meter, dan kedalaman hydraulic 3,05 meter.

scholarly journals Shear Performance of Optimized-Section Precast Slab with Tapered Cross Section

2018 ◽  
Vol 11 (1) ◽  
pp. 163 ◽  
Author(s):  
Hyunjin Ju ◽  
Sun-Jin Han ◽  
Hyo-Eun Joo ◽  
Hae-Chang Cho ◽  
Kang Kim ◽  
...  
Keyword(s):  
Cross Section ◽  
Design Method ◽  
Precast Concrete ◽  
Bending Moment ◽  
Shear Behaviour ◽  
Element Analysis ◽  
Cross Sectional ◽  
Shear Design ◽  
Shear Performance ◽  
And Performance

The optimized-section precast slab (OPS) is a half precast concrete (PC) slab that highlights structural aesthetics while reducing the quantity of materials by means of an efficient cross-sectional configuration considering the distribution of a bending moment. However, since a tapered cross section where the locations of the top and bottom flanges change is formed at the end of the member, stress concentration occurs near the tapered cross section because of the shear force and thus the surrounding region of the tapered cross section may become unintentionally vulnerable. Therefore, in this study, experimental and numerical research was carried out to examine the shear behaviour characteristics and performance of the OPS with a tapered cross section. Shear tests were conducted on a total of eight OPS specimens, with the inclination angle of the tapered cross section, the presence of topping concrete and the amount of shear reinforcement as the main test variables and a reasonable shear-design method for the OPS members was proposed by means of a detailed analysis based on design code and finite-element analysis.

scholarly journals Analytical Model of a Multi-Step Straightening Process for Linear Guideways Considering Neutral Axis Deviation

Symmetry ◽  
2018 ◽  
Vol 10 (8) ◽  
pp. 316 ◽  
Author(s):  
Yongquan Zhang ◽  
Hong Lu ◽  
He Ling ◽  
Yang Lian ◽  
Mingtian Ma
Keyword(s):  
Analytical Model ◽  
Cross Section ◽  
Predictive Accuracy ◽  
Neutral Axis ◽  
Longitudinal Stress ◽  
Linear Superposition ◽  
Element Analysis ◽  
Cross Sectional ◽  
The Cross ◽  
Sectional Shape

The cross-sectional shape of a linear guideway has been processed before the straightening process. The cross-section features influence not only the position of the neutral axis, but also the applied and residual stresses along the longitudinal direction, especially in a multi-step straightening process. This paper aims to present an analytical model based on elasto-plastic theory and three-point reverse bending theory to predict straightening stroke and longitudinal stress distribution during the multi-step straightening process of linear guideways. The deviation of the neutral axis is first analyzed considering the asymmetrical features of the cross-section. Owing to the cyclic loading during the multi-step straightening process, the longitudinal stress curves are then calculated using the linear superposition of stresses. Based on the cross-section features and the superposition of stresses, the bending moment is corrected to improve the predictive accuracy of the multi-step straightening process. Finite element analysis, as well as straightening experiments, have been performed to verify the applicability of the analytical model. The proposed approach can be implemented in the multi-step straightening process of linear guideways with similar cross-sectional shape to improve the straightening accuracy.

Erythrocyte Sedimentation Rates in Inclined Vessels

1973 ◽  
Vol 51 (9) ◽  
pp. 685-690 ◽  
Author(s):  
R. N. O'Brien ◽  
M. B. Hocking ◽  
P. McOrmond ◽  
K. R. Thornton
Keyword(s):  
Cross Section ◽  
Sedimentation Rates ◽  
Settling Rate ◽  
Cross Sectional ◽  
Erythrocyte Sedimentation ◽  
The Cross ◽  
Sectional Shape ◽  
Erythrocyte Sedimentation Rates ◽  
Test Rack ◽  
Settling Rates

The rates of erythrocyte settling have been investigated in round and square cross-section tubes, vertically; and at nine different angles; and with the square tubes flat and on edge, to a minimum of 15° from the horizontal. Apparent settling rates increased as the angle from the horizontal decreased. Real settling rates (vertical settling rates) increased sharply on decreasing the angle from the horizontal, to a maximum at about 60°, and then decreased less abruptly for the shallower angles. The cross-sectional shape of the tube did not significantly affect the settling rates of erythrocytes. Settling in inclined tubes proceeds fast enough to permit clinical erythrocyte settling rate (E.S.R.) tests to be carried out in 10 min in place of the usual 60 min. If the standard E.S.R. test rack deviates as little as 5° from the vertical it can cause the observed settling rates to double relative to readings obtained on a vertical rack.

Sign in / Sign up

Export Citation Format

Share Document