Thermal and Structural Response of Pin Fins for Different Interface Conditions

2010 ◽  
Author(s):  
Abul Fazal M. Arif ◽  
Sulaman Pashah ◽  
Syed M. Zubair ◽  
M. Inam
Keyword(s):  
Thermal Performance ◽  
Heat Sink ◽  
Heat Dissipation ◽  
Structural Response ◽  
Operating Conditions ◽  
Stress Fields ◽  
Power Device ◽  
Interface Conditions ◽  
Thermal Interface ◽  
Pin Fin

Thermal management of electronic products relies on the effective dissipation of heat. Heat sink elements (e.g. a pin fin) are used for any effective heat dissipation network. Despite much optimized design of the heat sink element, the heat transfer may not be effective because the interface between power device and heat sink element is critical in the heat dissipation network. Thermal Interface Materials TIM (e.g. adhesive, solder, pads, or pastes) are employed at interface between power device and heat sink element to minimize the interface thermal resistance. However, several challenges need to be addressed before they can be successfully utilized because depending on the thermal interface conditions, the thermal stress level can attain undesirable values. This issue can be addressed by the optimization of the system design with the help of simulation methods. Generally the effects of interface conditions are studied on the thermal performance of the heat sink system whereas in this paper, a coupled-field (thermal-structural) analysis using FEM is performed to study the thermal as well as structural behavior of the heat sink system. Temperature variation and stress fields in the region of interface between pin fin and base plate are analyzed. Effects of various parameters (such as contact pressure, surface roughness, TIM thickness, and operating conditions) on the resulting thermal and structural response at the interface are presented. It has been found that different interface conditions may have comparable thermal performance with significant different stress fields at the interface. Therefore stress state must be known to ensure the structural integrity of the heat sink system for a given operating condition.

scholarly journals Investigation of the Thermal Performance of Salt Hydrate Phase Change of Nanoparticle Slurry Flow in a Microchannel

2019 ◽  
Vol 2019 ◽  
pp. 1-10
Author(s):  
Safi A. Memon ◽  
M. B. Sajid ◽  
M. S. Malik ◽  
Awad B. S. Alquaity ◽  
M. Mohib ur. Rehman ◽  
...  
Keyword(s):  
Phase Change ◽  
Thermal Performance ◽  
Lauric Acid ◽  
Heat Sink ◽  
Heat Dissipation ◽  
Computational Study ◽  
Operating Conditions ◽  
Slurry Flow ◽  
Design Guideline ◽  
Salt Hydrate

Computational study was conducted to investigate the thermal performance of water-based salt hydrate S44 nanoparticles as the phase change material (PCM) in a microchannel heat sink. Constant heat dissipation was applied on the top wall of the heat sink. Forced internal convection of the PCM slurry flow was performed through a homogeneous approach. Three thermal performance parameters, including effectiveness ratio, performance index, and Merit number, were used to quantify the cooling performance of S44 for various concentrations of the PCM nanoparticles. The thermal performance of the salt hydrate S44 slurry was also compared with a similar study conducted for lauric acid nanoparticle slurry found in the literature. Specific operating conditions were identified. The salt hydrate S44 would provide better thermal performance than lauric acid, and vice versa. Finally, Nusselt number correlations have been developed for the microchannel PCM heat sink for Reynolds numbers in the range 12.23 to 47.14 and Prandtl numbers in the range 3.74 to 5.30. A design guideline for manufacturing PCM particles and microchannel heat sinks is provided. With this guideline, the heat absorption ability of the heat sink is maximized, and the pumping power and the losses related to the addition of the particles are minimized.

Effect of Heat Sink Structure Improvement on Heat Dissipation Performance in High Heat Flux

2016 ◽  
Author(s):  
Zhuo Cui
Keyword(s):  
Heat Resistance ◽  
Water Flow ◽  
Heat Sink ◽  
Heat Dissipation ◽  
Convection Heat Transfer ◽  
Cooling Water ◽  
High Heat Flux ◽  
Pin Fin ◽  
Pin Fins ◽  
Pin Fin Arrays

This paper presents the effects of heat dissipation performance of pin fins with different heat sink structures. The heat dissipation performance of two types of pin fin arrays heat sink are compared through measuring their heat resistance and the average Nusselt number in different cooling water flow. The temperature of cpu chip is monitored to determine the temperature is in the normal range of working temperature. The cooling water flow is in the range of 0.02L/s to 0.15L/s. It’s found that the increase of pin fins in the corner region effectively reduce the temperature of heat sink and cpu chip. The new type of pin fin arrays increase convection heat transfer coefficient and reduce heat resistance of heat sink.

Thermal-Structural Performance of Orthotropic Pin Fin in Electronics Cooling Applications

2012 ◽  
Vol 134 (4) ◽  
Author(s):  
A. F. M. Arif ◽  
Syed M. Zubair ◽  
S. Pashah
Keyword(s):  
Heat Sink ◽  
Structural Response ◽  
Electronics Cooling ◽  
Base Plate ◽  
Thermal Design ◽  
Heat Flow Rate ◽  
Thermal Interface ◽  
Conductive Composites ◽  
Thermally Conductive ◽  
As Stress

Thermally conductive composites as compared to metals have reduced density, decreased oxidation, and improved chemical resistance, as well as adjustable properties to fit a given application. However, there are several challenges that need to be addressed before they can be successfully implemented in heat sink design. The interface between the device and heat sink is an important factor in the thermal design of microelectronics cooling. Depending on the thermal interface conditions and material properties, the contact pressure and thermal stress level can attain undesirable values. In this paper, we investigate the effect of thermal interface between the fin and base plate on thermal-structural behavior of heat sinks. A coupled-field (thermal-structural) analysis using finite element method is performed to predict temperature as well as stress fields in the interface region. In addition temperature and heat flow rate predictions are supported through analytical results. effect of various interface geometrical (such as slot-depth, axial-gap, and radial-gap) and contact properties (such as air gap with surface roughness and gaps filled with interface material) on the resulting thermal-structural response is investigated with respect to four interface materials combinations, and it is found that the thermal performance is most sensitive to the slot-depth compared to any other parameter.

Thermal Design Analysis of 2.5-D Packages With Analytical TSV Submodels

2015 ◽  
Author(s):  
H. Y. Zhang ◽  
Xiao Yan ◽  
W. H. Zhu ◽  
Leon Lin
Keyword(s):  
Thermal Performance ◽  
Heat Sink ◽  
Power Dissipation ◽  
High Current Density ◽  
Hot Spot ◽  
Thermal Design ◽  
Good Prediction ◽  
Excessive Heat ◽  
Pin Fin ◽  
Power Application

2.5-D package with through silicon vias (TSVs) on interposer has been envisioned as the most viable way in heterogeneous integration. In this work, several design approaches are considered in the thermal analysis and enhancements of a 2.5-D package with multi chips on through silicon interposer (TSI), which include overmolding materials, metal slug, lid attachment, pin fin heat sink and fan-driven heat sink cooling. The analysis models consist of two dummy flip chips on a silicon interposer to represent the logic die and memory die, respectively. Package submodels, especially the TSV ones, are analyzed with good modeling accuracy. Package thermal modeling indicates that the thermal conductivity of the epoxy overmolding has minimal effect on the thermal performance of copper slug package. Lid attachment further enhances the thermal performance through peripheral substrate attachment. Both designs largely rely on thermally conductive PCB (4L) to maximize power dissipation. Pin-fin heat sink, made of aluminum, can be mounted on the package top to further minimize thermal resistance and extend the power dissipation beyond 10W. For high power application, fan cooled heat sink is used to reduce excessive heat. Copper based aluminum heat sink can remove the heat of 120W from the bare-die package. Self heating due to high current density through the TSV is analyzed. The proposed analytical expression gives good prediction on the local TSV hot spot. It is demonstrated that a distributed TSV network design provides lower temperature rise, which shall have lower risk of failures and is preferred in practice.

Experimental Investigation of a PCM-Based Topology Optimized Heat Sink for Passive Cooling of Electronics

2020 ◽  
Author(s):  
Jin Yao Ho ◽  
Kai Choong Leong
Keyword(s):  
Thermal Performance ◽  
Heat Sink ◽  
Heat Dissipation ◽  
Volume Fraction ◽  
Solid Volume Fraction ◽  
Heat Fluxes ◽  
Heat Sinks ◽  
Base Temperature ◽  
Storage Unit ◽  
Cooling Of Electronics

Abstract A thermal energy storage unit filled with phase change material (PCM) can serve as a heat sink for the cooling of electronics with intermittent or periodic heat dissipation rates. The use of thermal conductive structures (TCS) is an effective method of improving the thermal performance of a PCM-based heat sink. In this paper, topology optimization is explored to develop a new class of TCS with a tree-like structure to enhance the thermal performance of a trapezoidal heat sink. The topology-optimized heat sink was then fabricated by Selective Laser Melting (SLM) using an aluminum alloy, AlSi10Mg, as the base powder. Experiments were performed to evaluate the thermal performance of the topology-optimized heat sink with the tree-like structure. In addition, a conventional longitudinal-fin heat sink of the same solid volume fraction (φ = 16.2%) and a heat sink without enhanced structure were also fabricated and experimentally investigated for comparison. Rubitherm RT-35HC paraffin wax was used as the PCM. Three different heat fluxes of 4.00 kW/m2, 5.08 kW/m2 and 7.24 kW/m2 were applied at the base of each specimen by a silicone rubber heater. The structure wall and the PCM temperatures were measured over time. Our results show that, for all heat rates tested, the topology-optimized heat sink was able to maintain a lower base temperature as compared to the fin-structure and the plain heat sinks. A thermal enhancement ratio (ε) is defined to evaluate the performance of the heat sinks with and without the use of PCM. From the experimental results, the highest ε value of 8.6 was achieved by the topology-optimized heat sink. These results indicate the better performance of the topology-optimized heat sink in dissipating heat as compared to the other specimens.

Advanced Cooling With Embedded Heat Pipes for High Power Microelectronics

2009 ◽  
Author(s):  
Victor Adrian Chiriac
Keyword(s):  
Heat Pipe ◽  
Thermal Performance ◽  
Heat Sink ◽  
Heat Pipes ◽  
Optimal Operation ◽  
Operating Conditions ◽  
Peak Temperature ◽  
Transient Temperature ◽  
Efficient Operation ◽  
The Impact

The transient thermal behavior of a complex testing system including multiple fans, a mixing enclosure, Cu inserts and a leaded package dissipating large amounts of power over short time durations is evaluated via numerical simulations. The system performance is optimized with heat sink/fan structure for device efficient operation under constant powering. The study provides meaningful understanding and prediction of a transient powering scenario at high powering levels, evaluating the impact of alternative cooling fan/heat pipe configurations on the thermal performance of the system. One design is chosen due to its effective thermal performance and assembly simplicity, with the package embedded in heat sink base with multiple (5) heat pipes. The peak temperature reached by the modified design with 4 cooling fans is ∼95°C, with the corresponding Rja thermal resistance ∼0.58°C/W. For the transient study (with embedded heat pipes and 4 fans), after one cycle, both peak temperature (at 45 s) and the end temperature (at 49 s) decrease as compared to the previous no heat pipe/single fan case (especially the end temperature reduces by ∼16%). The temperature drop between peak and end for each cycle is ∼80.2°C, while the average power per transient cycle is ∼31.27W. With this power, the design with 5 perpendicular heat pipes, 4 fans and insert reaches a steady state peak temperature of ∼98°C. Applying the superposition principle, the maximum transient temperature after a large number of operating cycles will not exceed ∼138.1°C, satisfying the thermal budget under the current operating conditions. The benefit of the study is related to the possibility to extract the maximum/minimum temperatures for a real test involving a large number of heating-cooling cycles, yet maintaining the initial and peak temperatures within a certain range for the optimal operation of the device. The flow and heat transfer fields are thoroughly investigated: using a combination of numerical and analytical study, the thermal performance of the device undergoing large number of periodic thermal cycles is predicted. Further comparison between measurement and simulation results reveals good agreement.

Thermal Assessment of Cooling System Incorporating Heat Sink and Embedded Heat Pipes for Testing High Power Microelectronics

2005 ◽  
Author(s):  
Victor Adrian Chiriac ◽  
Tien-Yu Tom Lee
Keyword(s):  
Steady State ◽  
Heat Pipe ◽  
Thermal Performance ◽  
Heat Sink ◽  
Heat Pipes ◽  
Optimal Operation ◽  
Operating Conditions ◽  
Peak Temperature ◽  
Testing System ◽  
The Impact

A numerical study was conducted to model the transient thermal behavior of a complex testing system including multiple fans, a mixing enclosure, copper inserts and a leaded package dissipating large amounts of power over short time durations. The system is optimized by choosing appropriate heat sink/fan structure for the efficient operation of the device under constant powering. The intent of the study is to provide a better understanding and prediction of a transient powering scenario at high powering levels, while evaluating the impact of alternative cooling fan/heat pipe designs on the thermal performance of the testing system. One design is chosen due to its effective thermal performance and assembly simplicity, with the package embedded in heat sink base with multiple (5) heat pipes. The peak temperature reached by the modified design with 4 cooling fans is ~95°C, with the corresponding Rja thermal resistance ~0.58°C/W. For the transient study (with embedded heat pipes and 4 fans), after one cycle, both peak temperature (at 45 s) and the end temperature (at 49 s) decrease as compared to the previous no heat pipe/single fan case (the end temperature reduces by ~16%). The temperature drop between peak and end for each cycle is ~80.2°C, while the average power per transient cycle is ~31.27W. With this power, the design with 5 perpendicular heat pipes, 4 fans and insert reaches a steady state peak temperature of ~98°C. Applying the superposition principle to the steady state value and 40.1°C fluctuation, the maximum transient temperature after a large number of cycles will not exceed ~138.1°C, satisfying the thermal budget under the current operating conditions. The benefit of the study is related to the possibility to extract the maximum and minimum temperatures for a real test involving a large number of heating-cooling cycles, yet maintaining the initial and peak temperatures within a certain range for the optimal operation of the device. The flow and heat transfer fields are investigated; using a combination of numerical and analytical methods, the thermal performance of the device undergoing large number of periodic thermal cycles is predicted. The comparison between measurement and simulation shows good agreement.

Sign in / Sign up

Export Citation Format

Share Document