Dynamic Stability of an Elastic Beam Subjected to Follower Forces

2012 ◽  
Author(s):  
Katsuhisa Fujita ◽  
Akihide Gotou
Keyword(s):  
Normal Modes ◽  
Elastic Beam ◽  
Conservative System ◽  
Critical Force ◽  
Concentrated Force ◽  
Nonconservative System ◽  
Damped System ◽  
Follower Forces ◽  
The Stability ◽  
The Relationship

The stability of nonconservative system of a beam is investigated when an elastic beam is subjected to follower forces. The mathematical formulations for a conservative system and a nonconservative system are established regarding to a uniform cantilever subjected to a concentrated force and a uniform distributed force axially. The displacement of a uniform cantilever is assumed to be obtained by superposing the modal functions which are normal modes in a vacuum, and is estimated by applying the Galerkin’s method. Changing the forces, the eigenvalue analysis is performed, and the root locus is calculated for the stability analysis. And, the relationship between forces and frequencies for the undamped system and the damped system of the uniform cantilever subjected to a concentrated force and a uniform distributed force is investigated. When the system is considered to be conservative, the divergence phenomenon is confirmed to appear first. On the other hand, when the system is considered to be nonconservative, the flutter phenomenon is confirmed to appear first although the critical force becomes high. And, by changing the structural damping, the destabilized effect due to the damping is confirmed when an elastic beam is subjected to follower forces.

Interface Conditions and Loss of Stability for Stepped Columns

2007 ◽  
Vol 9 ◽  
pp. 41-50 ◽  
Author(s):  
Roman Bogacz ◽  
Kurt Frischmuth ◽  
Krzysztof Lisowski
Keyword(s):  
Dynamic Behavior ◽  
Critical Loads ◽  
Stability Limit ◽  
Critical Force ◽  
Loss Of Stability ◽  
Interface Conditions ◽  
Compatibility Conditions ◽  
Worst Case ◽  
Follower Forces ◽  
The Stability

We discuss the dynamic behavior of stepped columns subjected to follower forces. In particular, limit cases which correspond to columns with hinges or cracks and concentrated lateral supports are studied for the stability limit. Typically, solutions suffer jumps in certain derivatives, which have to satisfy compatibility conditions. The influence of these interface conditions on the critical force is investigated. The aim is to optimize the location of such singularities and thus to obtain maximum critical loads, respectively worst case estimates for the loss of stability.

Effects of Forward/Backward Whirl Mechanism on Nonlinear Normal Modes of a Rotor/Stator Rubbing System

2015 ◽  
Vol 137 (5) ◽  
Author(s):  
Yanhua Chen ◽  
Jun Jiang
Keyword(s):  
Response Spectrum ◽  
Normal Modes ◽  
Nonlinear Normal Modes ◽  
Frequency Component ◽  
Harmonic Response ◽  
Backward Whirl ◽  
Coupling Stiffness ◽  
Nonlinear Normal ◽  
The Stability ◽  
The Relationship

In this paper, the effects of forward and backward whirl mechanism on the existence and the stability of multiple nonlinear normal modes (NNMs) in a four degree-of-freedom (DOF) rotor/stator rubbing system with cross-coupling stiffness and dry friction are investigated analytically. The NNMs may possess either positive or negative modal frequencies, corresponding, respectively, to the inherent motions of forward or backward whirl, and can be either stable or unstable. The relationship between the NNMs, regarding to their stability, and the forced system responses of the system is of great interest. It is found that a stable NNM corresponds to a forced harmonic response with the same whirl direction and frequency as the NNM, and an unstable NNM may still influence some forced system responses by contributing a frequency component equal to the modal frequency to the response spectrum.

On the Sufficiency of the Energy Criterion for the Stability of Certain Nonconservative Systems of the Follower-Load Type

1972 ◽  
Vol 39 (3) ◽  
pp. 717-722 ◽  
Author(s):  
H. H. E. Leipholz
Keyword(s):  
Lower Bound ◽  
Critical Load ◽  
Energy Criterion ◽  
Conservative System ◽  
Buckling Load ◽  
Follower Load ◽  
Nonconservative System ◽  
Nonconservative Systems ◽  
Divergence Type ◽  
The Stability

Using Galerkin’s method it is shown that in the domain of divergence, the nonconservative system of the follower-load type is always more stable than the corresponding conservative system. Hence, for nonconservative systems of the divergence type, the critical load of the corresponding conservative system becomes a lower bound for the buckling load, and the energy criterion remains sufficient for predicting stability. Moreover, it is proven that even for more general nonconservative systems, the energy criterion is sufficient under certain restrictions.

scholarly journals Elastohydrodynamical instabilities of active filaments, arrays and carpets analyzed using slender body theory

2020 ◽  
Author(s):  
Ashok S. Sangani ◽  
Arvind Gopinath
Keyword(s):  
Critical Force ◽  
Slender Body ◽  
Critical Parameters ◽  
Neutral Stability ◽  
Slender Body Theory ◽  
Follower Forces ◽  
Freely Suspended ◽  
Filament Spacing ◽  
The Stability ◽  
Body Theory

ABSTRACTThe rhythmic motions and wave-like planar oscillations in filamentous soft structures are ubiquitous in biology. Inspired by these, recent work has focused on the creation of synthetic colloid-based active mimics that can be used to move, transport cargo, and generate fluid flows. Underlying the functionality of these mimics is the coupling between elasticity, geometry, dissipation due to the fluid, and active force or moment generated by the system. Here, we use slender body theory to analyze the linear stability of a subset of these - active elastic filaments, filament arrays and filament carpets - animated by follower forces. Follower forces can be external or internal forces that always act along the filament contour. The application of slender body theory enables the accurate inclusion of hydrodynamic effects, screening due to boundaries, and interactions between filaments. We first study the stability of fixed and freely suspended sphere-filament assemblies, calculate neutral stability curves separating stable oscillatory states from stable straight states, and quantify the frequency of emergent oscillations. When shadowing effects due to the physical presence of the spherical boundary are taken into account, the results from the slender body theory differ from that obtained using local resistivity theory. Next, we examine the onset of instabilities in a small cluster of filaments attached to a wall and examine how the critical force for onset of instability and the frequency of sustained oscillations depend on the number of filaments and the spacing between the filaments. Our results emphasize the role of hydrodynamic interactions in driving the system towards perfectly in-phase or perfectly out of phase responses depending on the nature of the instability. Specifically, the first bifurcation corresponds to filaments oscillating in-phase with each other. We then extend our analysis to filamentous (line) array and (square) carpets of filaments and investigate the variation of the critical parameters for the onset of oscillations and the frequency of oscillations on the inter-filament spacing. The square carpet also produces a uniform flow at infinity and we determine the ratio of the mean-squared flow at infinity to the energy input by active forces. We conclude by analyzing the bending and buckling instabilities of a straight passive filament attached to a wall and placed in a viscous stagnant flow - a problem related to the growth of biofilms, and also to mechanosensing in passive cilia and microvilli. Taken together, our results provide the foundation for more detailed non-linear analyses of spatiotemporal patterns in active filament systems.

scholarly journals Side busking of the cantilever beam with narrow rectangular cross section

2019 ◽  
Vol 97 ◽  
pp. 04066
Author(s):  
Serdar Yazyev ◽  
Ivan Zotov ◽  
Dmitriy Vysokovsky ◽  
Batyr Yazyev
Keyword(s):  
Analytical Solution ◽  
Cross Section ◽  
Beam Energy ◽  
Secular Equation ◽  
Rectangular Cross Section ◽  
Critical Force ◽  
Lateral Buckling ◽  
Concentrated Force ◽  
Comparison Of The Results ◽  
The Relationship

The problem of lateral buckling of a cantilever strip with a constant narrow cross section loaded with a concentrated force at the end of the span is considered. In the study of lateral buckling of beam energy method was used. For the case of load application in the center of gravity, the problem is reduced to a generalized secular equation. The relationship between the magnitude of the critical force and the position of the point of application of the load. A comparison of the results obtained by the authors with an analytical solution using infinite series and a numerical iterative method is shown.

An Experimental Investigation on Thermal Conductivity and Viscosity of Graphene doped CNTs /TiO2 Nanofluid

2020 ◽  
Vol 17 (3) ◽  
Author(s):  
A.M. Zetty Akhtar ◽  
M.M. Rahman ◽  
K. Kadirgama ◽  
M.A. Maleque
Keyword(s):  
Thermal Conductivity ◽  
Zeta Potential ◽  
Base Fluid ◽  
Minimum Quantity Lubrication ◽  
Cutting Fluid ◽  
Cutting Zone ◽  
Observation Method ◽  
The Stability ◽  
The Relationship ◽  
Zeta Potential Analysis

This paper presents the findings of the stability, thermal conductivity and viscosity of CNTs (doped with 10 wt% graphene)- TiO2 hybrid nanofluids under various concentrations. While the usage of cutting fluid in machining operation is necessary for removing the heat generated at the cutting zone, the excessive use of it could lead to environmental and health issue to the operators. Therefore, the minimum quantity lubrication (MQL) to replace the conventional flooding was introduced. The MQL method minimises the usage of cutting fluid as a step to achieve a cleaner environment and sustainable machining. However, the low thermal conductivity of the base fluid in the MQL system caused the insufficient removal of heat generated in the cutting zone. Addition of nanoparticles to the base fluid was then introduced to enhance the performance of cutting fluids. The ethylene glycol used as the base fluid, titanium dioxide (TiO2) and carbon nanotubes (CNTs) nanoparticle mixed to produce nanofluids with concentrations of 0.02 to 0.1 wt.% with an interval of 0.02 wt%. The mixing ratio of TiO2: CNTs was 90:10 and ratio of SDBS (surfactant): CNTs was 10:1. The stability of nanofluid checked using observation method and zeta potential analysis. The thermal conductivity and viscosity of suspension were measured at a temperature range between 30˚C to 70˚C (with increment of 10˚C) to determine the relationship between concentration and temperature on nanofluid’s thermal physical properties. Based on the results obtained, zeta potential value for nanofluid range from -50 to -70 mV indicates a good stability of the suspension. Thermal conductivity of nanofluid increases as an increase of temperature and enhancement ratio is within the range of 1.51 to 4.53 compared to the base fluid. Meanwhile, the viscosity of nanofluid shows decrements with an increase of the temperature remarks significant advantage in pumping power. The developed nanofluid in this study found to be stable with enhanced thermal conductivity and decrease in viscosity, which at once make it possible to be use as nanolubricant in machining operation.

A FORECAST OF PRODUCTIVE LONGEVITY OF HOLSTEIN COWS BY INDIRECT SIGNS

2020 ◽  
Author(s):  
З.С. САНОВА
Keyword(s):  
Correlation Coefficient ◽  
Aging Process ◽  
Direct Relationship ◽  
Stability Index ◽  
Age At First Calving ◽  
Group I ◽  
Predicted Values ◽  
The Stability ◽  
Relationship Of ◽  
The Relationship

В статье представлены материалы о взаимосвязи продолжительности продуктивного использования коров с характеристикой устойчивости к деградации, с возрастом отела и удоем. В исследованной, разнородной по происхождению, группе животных для прогноза продуктивного периода коров, обусловленного устойчивостью к деградации и возрастом первого отела, пригодно уравнение регрессии, аргументами в котором являются индекс устойчивости, возраст первого отела в первой и второй степенях. Коэффициент корреляции межу предсказанными значениями продуктивного периода и его фактическими величинами в I группе составляет 0,502, во II - 0,604. При этом крайние варианты прогнозируются со статистическими ошибками 5 мес при оценке индекса устойчивости по 2 лактациям и 4,1 мес по 3, а средние варианты, соответственно, 1,6 и 1,51 мес. Индекс устойчивости к процессу старения является важной характеристикой биологических особенностей коров, определяющий их продуктивное долголетие. Его оценка по первым 2 и 3 лактациям имеет прямолинейную связь с продуктивным периодом (r=0,4109 и r=0,5270), соответственно. Зависимость продуктивного периода от возраста первого отела криволинейная — с увеличением возраста первого отела сокращается срок продуктивного использования, при возрасте первого отела более 1400 дней срок продуктивного использования колеблется от 1,33 до 1,41 лактации. Коэффициент корреляции между этими характеристиками коров составляет - 0,2164 в I и - 0,2620 во II группах. The article presents materials about the relationship of the duration of productive use of cows with the characteristic of resistance to degradation, with the age of calving and milk yield. In the studied group of animals, which is heterogeneous in origin, the regression equation is suitable for predicting the productive period of cows due to resistance to degradation and the age of the first calving, the arguments of which are the stability index, the age of the first calving in the first and second degrees. The correlation coefficient between the predicted values of the productive period and its actual values in group I is 0.502, in group II - 0.604. At the same time, the extreme variants are predicted with statistical errors of 5 months when evaluating the stability index for 2 lactations and 4.1 months for 3, and the average variants, respectively, are 1.6 and 1.51 months. The index of resistance to the aging process is an important characteristic of the biological characteristics of cows, which determines their productive longevity. Its estimate for the first 2 and 3 lactations has a direct relationship with the productive period (r=0.4109 and r=0.5270), respectively. The dependence of the productive period age at first calving curvilinear with increasing age at first calving reduces the time to productive use, while age at first calving of more than 1400 days, the period of productive use ranges from 1.33 to 1.41 lactation. The correlation coefficient between these characteristics of cows is-0.2164 in I and-0.2620 in II groups.

Substantiation the machine with a basket for the application of mineral fertilizers and other bulk materials with the upper arrangement of the feeding device

2019 ◽  
pp. 37-43
Author(s):  
Fesenko, H.
Keyword(s):  
Fat Body ◽  
Mineral Fertilizer ◽  
The Body ◽  
Mineral Fertilizers ◽  
Analytical Mechanics ◽  
Bulk Materials ◽  
The Stability ◽  
Working Bodies ◽  
The Relationship ◽  
Stable Flow

Purpose. Increasing the uniformity of distribution of mineral fertilizers and other bulk materials due to the stability of their feed from the body to the spreading working bodies using the top feeder. Methods. The following methods are used to achieve this aim: the method of comparing the differences between individual groups of fertilizers, the method of analyzing the properties of a new technical system, the method of functional inventiveness, and the methods of theoretical and analytical mechanics. Results. The traction body of the conveyor of the upper feed of the body fat body machine for mineral fertilizers and other bulk materials was substantiated and the relationship between the height of its scrapers and the distance between them was established, as well as the nature of the mineral fertilizer pressure on the curvilinear wall of the body. In addition, the design of the advanced body fertilizer spreader is justified, which ensures a stable flow of fertilizers from the body due to the improvement of the top feeder. Conclusions. Because of the conducted researches, the advantages of machines equipped with top feeder are found. They create the conditions for the forced feeding mineral fertilizers and other loose materials from the container to the distribution bodies, which is a prerequisite for their evenness on the surface. With this, the imperfection of known machines with the top feeder constrains their introduction into agricultural production. On this account, a more thoroughly constructed solution of the body feeder of the top feed is substantiated, in which the conveyor provides a stable supply of fertilizers from the body with reduced energy consumption during operation. Keywords: analysis, feed, upper device, conveyor, stability, fertilizers, flow ability, body.

FINANCIAL CRISES AND THE PUBLICATION OF THE FINANCIAL STATEMENTS OF BANKS IN SPAIN, 1844–1868

2004 ◽  
Vol 31 (2) ◽  
pp. 1-26 ◽  
Author(s):  
Mercedes Bernal Lloréns
Keyword(s):  
19Th Century ◽  
Financial Reporting ◽  
Economic Performance ◽  
Financial Crises ◽  
Limited Liability ◽  
Financial Statements ◽  
Early Response ◽  
Banking Regulations ◽  
The Stability ◽  
The Relationship

Financial crises have had a decisive influence on banking regulations in Spain. During the mid-19th century the publication of the financial statements of banks was considered key to the stability of the financial system. All new joint stock banking companies were to publish their statements in the Madrid Gazette in return for the privilege of limited liability. Similar obligations were placed on issuing banks. The copious publication of financial statements coincided with a period of financial prosperity. However, the crises that followed from 1864 to 1868 led to a reduction in the official publication of statements. This paper is concerned with an early response to crises in financial reporting. The study focuses on the relationship between the publication of accounting statements by banks and the GDP in Spain during the mid-19th century. The results suggest that the frequency of publication of financial statements may be an indicator of economic performance.

scholarly journals Cats in the forest: predicting habitat adaptations from humerus morphometry in extant and fossil Felidae (Carnivora)

Paleobiology ◽  
10.1666/12001 ◽  
2013 ◽  
Vol 39 (3) ◽  
pp. 323-344 ◽  
Author(s):  
Carlo Meloro ◽  
Sarah Elton ◽  
Julien Louys ◽  
Laura C. Bishop ◽  
Peter Ditchfield
Keyword(s):  
Morphological Variability ◽  
Olduvai Gorge ◽  
Environmental Predictors ◽  
Linear Measurements ◽  
Multivariate Statistical ◽  
Linear Discriminant ◽  
Related Group ◽  
Discriminant Analyses ◽  
The Stability ◽  
The Relationship

Mammalian carnivores are rarely incorporated in paleoenvironmental reconstructions, largely because of their rarity within the fossil record. However, multivariate statistical modeling can be successfully used to quantify specific anatomical features as environmental predictors. Here we explore morphological variability of the humerus in a closely related group of predators (Felidae) to investigate the relationship between morphometric descriptors and habitat categories. We analyze linear measurements of the humerus in three different morphometric combinations (log-transformed, size-free, and ratio), and explore four distinct ways of categorizing habitat adaptations. Open, Mixed, and Closed categories are defined according to criteria based on traditional descriptions of species, distributions, and biome occupancy. Extensive exploratory work is presented using linear discriminant analyses and several fossils are included to provide paleoecological reconstructions.We found no significant differences in the predictive power of distinct morphometric descriptors or habitat criteria, although sample splitting into small and large cat guilds greatly improves the stability of the models. Significant insights emerge for three long-canine cats:Smilodon populator,Paramachairodus orientalis, andDinofelissp. from Olduvai Gorge (East Africa).S. populatorandP. orientalisare both predicted to have been closed-habitat adapted taxa. The false “sabertooth”Dinofelissp. from Olduvai Gorge is predicted to be adapted to mixed habitat. The application of felid humerus ecomorphology to the carnivoran record of Olduvai Gorge shows that the older stratigraphic levels (Bed I, 1.99–1.79 Ma) included a broader range of environments than Beds II or V, where there is an abundance of cats adapted to open environments.

Sign in / Sign up

Export Citation Format

Share Document