Fabrication and characterization of flexible hybrid transparent electrodes with broadband transparency

2021 ◽  
pp. 2140023
Author(s):  
Keh-Moh Lin ◽  
Swapnil Shinde ◽  
Ru-Li Lin ◽  
Wen-Tse Hsiao ◽  
Pankaj Koinkar
Keyword(s):  
Sheet Resistance ◽  
Bending Test ◽  
Transparent Electrodes ◽  
Radio Frequency Sputtering ◽  
Light Region ◽  
Average Transmittance ◽  
Continuous State ◽  
Wide Range ◽  
Polyethylene Terephthalate Substrate

In this study, indium-zinc oxide (IZO)/silver (Ag)/IZO (ZAZ) flexible transparent electrodes were prepared on polyethylene terephthalate substrate using radio frequency sputtering technique. Experimental results showed that when the Ag film transited from semi-continuous state to continuous state, the ZAZ electrode exhibited high optoelectronic performance. The best ZAZ sample had a quite wide range of high transmittance and an average transmittance of 78.9% in visible light region, and sheet resistance of [Formula: see text]/sq and a Haacke Index of [Formula: see text]. The bending test revealed that the [Formula: see text] (change in sheet resistance) of ZAZ electrodes after 1000 bends was still less than 25% while the electrical properties of IZO films deteriorated after only 100 bending tests.

Polymer Chemistry

2004 ◽  
Keyword(s):  
Conducting Polymers ◽  
Liquid Crystalline ◽  
Polymer Chemistry ◽  
Chain Growth ◽  
Crystalline Polymers ◽  
Wide Range ◽  
Cyclic Oligomers ◽  
Step Growth

Polymer Chemistry: A Practical Approach in Chemistry has been designed for both chemists working in and new to the area of polymer synthesis. It contains detailed instructions for preparation of a wide-range of polymers by a wide variety of different techniques, and describes how this synthetic methodology can be applied to the development of new materials. It includes details of well-established techniques, e.g. chain-growth or step-growth processes together with more up-to-date examples using methods such as atom-transfer radical polymerization. Less well-known procedures are also included, e.g. electrochemical synthesis of conducting polymers and the preparation of liquid crystalline elastomers with highly ordered structures. Other topics covered include general polymerization methodology, controlled/"living" polymerization methods, the formation of cyclic oligomers during step-growth polymerization, the synthesis of conducting polymers based on heterocyclic compounds, dendrimers, the preparation of imprinted polymers and liquid crystalline polymers. The main bulk of the text is preceded by an introductory chapter detailing some of the techniques available to the scientist for the characterization of polymers, both in terms of their chemical composition and in terms of their properties as materials. The book is intended not only for the specialist in polymer chemistry, but also for the organic chemist with little experience who requires a practical introduction to the field.

scholarly journals Organelle Genetics in Plants

2021 ◽  
Vol 22 (4) ◽  
pp. 2104
Author(s):  
Pedro Robles ◽  
Víctor Quesada
Keyword(s):  
Rna Editing ◽  
Posttranscriptional Regulation ◽  
Genome Engineering ◽  
Plant Mitochondria ◽  
Plastid Dna ◽  
Chloroplast Genomes ◽  
Wide Range ◽  
Organelle Genetics ◽  
Selection Of

Eleven published articles (4 reviews, 7 research papers) are collected in the Special Issue entitled “Organelle Genetics in Plants.” This selection of papers covers a wide range of topics related to chloroplasts and plant mitochondria research: (i) organellar gene expression (OGE) and, more specifically, chloroplast RNA editing in soybean, mitochondria RNA editing, and intron splicing in soybean during nodulation, as well as the study of the roles of transcriptional and posttranscriptional regulation of OGE in plant adaptation to environmental stress; (ii) analysis of the nuclear integrants of mitochondrial DNA (NUMTs) or plastid DNA (NUPTs); (iii) sequencing and characterization of mitochondrial and chloroplast genomes; (iv) recent advances in plastid genome engineering. Here we summarize the main findings of these works, which represent the latest research on the genetics, genomics, and biotechnology of chloroplasts and mitochondria.

scholarly journals Characterization of a Novel CaCO3-Forming Alkali-Tolerant Rhodococcus erythreus S26 as a Filling Agent for Repairing Concrete Cracks

Molecules ◽  
2021 ◽  
Vol 26 (10) ◽  
pp. 2967
Author(s):  
Seunghoon Choi ◽  
Sungjin Park ◽  
Minjoo Park ◽  
Yerin Kim ◽  
Kwang Min Lee ◽  
...  
Keyword(s):  
Building Materials ◽  
Culture Fluid ◽  
Natural Phenomenon ◽  
Environment Friendly ◽  
Wide Range ◽  
Filling Agent ◽  
Calcium Source ◽  
Alkali Tolerance ◽  
High Alkali

Biomineralization, a well-known natural phenomenon associated with various microbial species, is being studied to protect and strengthen building materials such as concrete. We characterized Rhodococcus erythreus S26, a novel urease-producing bacterium exhibiting CaCO3-forming activity, and investigated its ability in repairing concrete cracks for the development of environment-friendly sealants. Strain S26 grown in solid medium formed spherical and polygonal CaCO3 crystals. The S26 cells grown in a urea-containing liquid medium caused culture fluid alkalinization and increased CaCO3 levels, indicating that ureolysis was responsible for CaCO3 formation. Urease activity and CaCO3 formation increased with incubation time, reaching a maximum of 2054 U/min/mL and 3.83 g/L, respectively, at day four. The maximum CaCO3 formation was achieved when calcium lactate was used as the calcium source, followed by calcium gluconate. Although cell growth was observed after the induction period at pH 10.5, strain S26 could grow at a wide range of pH 4–10.5, showing its high alkali tolerance. FESEM showed rhombohedral crystals of 20–60 µm in size. EDX analysis indicated the presence of calcium, carbon, and oxygen in the crystals. XRD confirmed these crystals as CaCO3 containing calcite and vaterite. Furthermore, R. erythreus S26 successfully repaired the artificially induced large cracks of 0.4–0.6 mm width.

scholarly journals Isolation and Characterization of Strain Exiguobacterium sp. KRL4, a Producer of Bioactive Secondary Metabolites from a Tibetan Glacier

2021 ◽  
Vol 9 (5) ◽  
pp. 890
Author(s):  
Pietro Tedesco ◽  
Fortunato Palma Esposito ◽  
Antonio Masino ◽  
Giovanni Andrea Vitale ◽  
Emiliana Tortorella ◽  
...  
Keyword(s):  
Phenotypic Analysis ◽  
Biological Assays ◽  
C Elegans ◽  
Isolation And Characterization ◽  
Wide Range ◽  
Protein Encoding ◽  
Nematocidal Activity ◽  
Extremophilic Microorganisms ◽  
Unique Source

Extremophilic microorganisms represent a unique source of novel natural products. Among them, cold adapted bacteria and particularly alpine microorganisms are still underexplored. Here, we describe the isolation and characterization of a novel Gram-positive, aerobic rod-shaped alpine bacterium (KRL4), isolated from sediments from the Karuola glacier in Tibet, China. Complete phenotypic analysis was performed revealing the great adaptability of the strain to a wide range of temperatures (5–40 °C), pHs (5.5–8.5), and salinities (0–15% w/v NaCl). Genome sequencing identified KRL4 as a member of the placeholder genus Exiguobacterium_A and annotation revealed that only half of the protein-encoding genes (1522 of 3079) could be assigned a putative function. An analysis of the secondary metabolite clusters revealed the presence of two uncharacterized phytoene synthase containing pathways and a novel siderophore pathway. Biological assays confirmed that the strain produces molecules with antioxidant and siderophore activities. Furthermore, intracellular extracts showed nematocidal activity towards C. elegans, suggesting that strain KRL4 is a source of anthelmintic compounds.

scholarly journals Effects of Concentration and Spin Speed on the Optical and Electrical Properties of Silver Nanowire Transparent Electrodes

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2219
Author(s):  
Xiaopeng Li ◽  
Jiayue Zhou ◽  
Dejun Yan ◽  
Yong Peng ◽  
Yong Wang ◽  
...  
Keyword(s):  
Sheet Resistance ◽  
Spin Coating ◽  
Figure Of Merit ◽  
Silver Nanowires ◽  
Solution Concentration ◽  
Ethanol Solution ◽  
Silver Nanowire ◽  
Optical And Electrical Properties ◽  
Transparent Electrodes ◽  
Spin Speed

In this paper, silver nanowires (AgNWs) with a diameter of 40 nm and a length of 45 μm were dispersed into an ethanol solution to prepare AgNW solutions with concentrations of 1, 2, and 3 mg/mL, respectively. The AgNW solutions were then deposited on a glass substrate using spin-coating at 1000, 2000, and 3000 rpm for 45 s, respectively, to prepare transparent electrodes. The results showed that the distribution of AgNWs on the substrate increased in density with the increase in the AgNW solution concentration and the decrease in spin speed. The effect of concentration on the distribution of AgNWs was greater than that of the spin speed. The transmittance of each electrode was between 84.19% and 88.12% at 550 nm, the average sheet resistance was between 20.09 and 358.11 Ω/sq, the highest figure of merit (FoM) was 104.42, and the lowest haze value was 1.48%. The electrode prepared at 1000 rpm with a concentration of 2 mg/mL and that prepared at 3000 rpm with a concentration of 3 mg/mL were very similar in terms of the average sheet resistance, transmittance at 550 nm, FoM, and haze value; thus, these two electrodes could be considered equivalent. The haze value of the electrode was positively correlated with the spin speed at low concentration, but that relationship became inverse as the concentration rose. For the AgNWs used in this experiment with an aspect ratio of 1125, the concentration of the AgNW solution should reach at least 2 mg/mL to ensure that the FoM of the electrode is greater than 35.

scholarly journals Towards Reduced CNNs for De-Noising Phase Images Corrupted with Speckle Noise

Photonics ◽  
2021 ◽  
Vol 8 (7) ◽  
pp. 255
Author(s):  
Marie Tahon ◽  
Silvio Montresor ◽  
Pascal Picart
Keyword(s):  
Phase Error ◽  
Speckle Noise ◽  
Experimental Conditions ◽  
Benchmark Data ◽  
Wide Range ◽  
Phase Images ◽  
Different Depths ◽  
Phase Data ◽  
Do So

Digital holography is a very efficient technique for 3D imaging and the characterization of changes at the surfaces of objects. However, during the process of holographic interferometry, the reconstructed phase images suffer from speckle noise. In this paper, de-noising is addressed with phase images corrupted with speckle noise. To do so, DnCNN residual networks with different depths were built and trained with various holographic noisy phase data. The possibility of using a network pre-trained on natural images with Gaussian noise is also investigated. All models are evaluated in terms of phase error with HOLODEEP benchmark data and with three unseen images corresponding to different experimental conditions. The best results are obtained using a network with only four convolutional blocks and trained with a wide range of noisy phase patterns.

scholarly journals Raman Spectroscopy Investigation of Graphene Oxide Reduction by Laser Scribing

2021 ◽  
Vol 7 (2) ◽  
pp. 48
Author(s):  
Vittorio Scardaci ◽  
Giuseppe Compagnini
Keyword(s):  
Raman Spectroscopy ◽  
Graphene Oxide ◽  
Reduce Graphene Oxide ◽  
Oxide Reduction ◽  
Material Parameters ◽  
Laser Scribing ◽  
Wide Range ◽  
Scan Speed ◽  
Laser Reduction

Laser scribing has been proposed as a fast and easy tool to reduce graphene oxide (GO) for a wide range of applications. Here, we investigate laser reduction of GO under a range of processing and material parameters, such as laser scan speed, number of laser passes, and material coverage. We use Raman spectroscopy for the characterization of the obtained materials. We demonstrate that laser scan speed is the most influential parameter, as a slower scan speed yields poor GO reduction. The number of laser passes is influential where the material coverage is higher, producing a significant improvement of GO reduction on a second pass. Material coverage is the least influential parameter, as it affects GO reduction only under restricted conditions.

scholarly journals Characterization of Polysaccharidic Associations for Cosmetic Use: Rheology and Texture Analysis

Cosmetics ◽  
2021 ◽  
Vol 8 (3) ◽  
pp. 62
Author(s):  
Giovanni Tafuro ◽  
Alessia Costantini ◽  
Giovanni Baratto ◽  
Stefano Francescato ◽  
Laura Busata ◽  
...  
Keyword(s):  
Raw Materials ◽  
Immersion Test ◽  
High Viscosity ◽  
Natural Polymers ◽  
Public Attention ◽  
First Choice ◽  
Wide Range ◽  
Textural Parameters ◽  
Complementary Techniques

As public attention on sustainability is increasing, the use of polysaccharides as rheological modifiers in skin-care products is becoming the first choice. Polysaccharide associations can be used to increase the spreading properties of products and to optimize their sensorial profile. Since the choice of natural raw materials for cosmetics is wide, instrumental methodologies are useful for formulators to easily characterize the materials and to create mixtures with specific applicative properties. In this work, we performed rheological and texture analyses on samples formulated with binary and ternary associations of polysaccharides to investigate their structural and mechanical features as a function of the concentration ratios. The rheological measurements were conducted under continuous and oscillatory flow conditions using a rotational rheometer. An immersion/de-immersion test conducted with a texture analyzer allowed us to measure some textural parameters. Sclerotium gum and iota-carrageenan imparted high viscosity, elasticity, and firmness in the system; carob gum and pectin influenced the viscoelastic properties and determined high adhesiveness and cohesiveness. The results indicated that these natural polymers combined in appropriate ratios can provide a wide range of different textures and that the use of these two complementary techniques represents a valid pre-screening tool for the formulation of green products.

Detection and characterization of Leptospira spp. in dogs diagnosed with kidney and/or liver disease in Selangor, Malaysia

2021 ◽  
pp. 104063872110245
Author(s):  
Sabri A. Rahman ◽  
Kuan H. Khor ◽  
Siti Khairani-Bejo ◽  
Seng F. Lau ◽  
Mazlina Mazlan ◽  
...  
Keyword(s):  
Liver Disease ◽  
Mortality Rate ◽  
Direct Detection ◽  
Bacterial Disease ◽  
Pathogenic Leptospira ◽  
Wide Range ◽  
Leptospira Spp ◽  
Rrna Sequencing ◽  
The Common

Leptospirosis is a serious bacterial disease that affects both humans and animals. A wide range of symptoms have been described in humans; the disease in dogs is commonly associated with kidney and/or liver disease. In Malaysia, information about the common serovars infecting dogs is limited. Therefore, we investigated the occurrences of leptospirosis in 124 pet dogs diagnosed with kidney and/or liver disease. Blood, urine, abdominal effusion, and/or kidney and liver were collected from the dogs. Based on microscopic agglutination testing, 53 of 124 (42.7%) dogs were seropositive for leptospiral exposure. Sera were frequently positive to serovars Bataviae ( n = 12), Javanica ( n = 10), and Icterohaemorrhagiae ( n = 10). Direct detection using PCR showed that 42 of 124 (33.9%) of the whole blood and 36 of 113 (31.9%) urine samples were positive for pathogenic Leptospira spp. By PCR, 2 of 23 (9.1%) kidney and 2 of 23 (9.1%) liver were positive for pathogenic Leptospira spp. Abdominal effusion from 4 dogs were PCR-positive for pathogenic Leptospira spp. The species detected were L. interrogans, L. borgpetersenii, L. kirschneri, and L. kmetyi by partial 16S rRNA sequencing. We further identified and characterized 11 Leptospira spp. isolates from 8 dogs as serovars Bataviae, Javanica, and Australis. The mortality rate of the Leptospira-infected dogs was high (18 of 53; 34%).

Sign in / Sign up

Export Citation Format

Share Document