A LOW-VOLTAGE SCALABLE (1.8 V–0.75 V) CMOS FOLDED-CASCODE LC QUADRATURE VCO FOR RF RECEIVERS

2010 ◽  
Vol 19 (04) ◽  
pp. 835-857 ◽  
Author(s):  
S. M. REZAUL HASAN
Keyword(s):  
Monte Carlo ◽  
Phase Noise ◽  
Low Voltage ◽  
Supply Voltage ◽  
Voltage Scaling ◽  
Center Frequency ◽  
Cmos Process ◽  
Process Technology ◽  
Folded Cascode ◽  
Supply Voltage Scaling

This paper presents a scalable low voltage CMOS folded-cascode quadrature voltage controlled oscillator (QVCO) design for radio-frequency (RF) applications using the TSMC 0.18 μm 6M1P CMOS process technology. The simulated startup behavior of this proposed QVCO topology indicates that, the QVCO is free from bi-modal oscillation (frequency ambiguity). The QVCO provided extended voltage swing with the supply voltage scalable in the range of 1.8 V to 0.75 V. The QVCO operates in the frequency range of 4 GHz to 3 GHz (corresponding to supply voltage scaling in the range of 1.8 V to 0.75 V) with around 11.7% tuning range and low quadrature error. The QVCO had a power consumption under 10 mW within the specified supply voltage scaling range. Phase noise simulations using the Monte Carlo analysis provide an approximate phase noise estimate of ≈ -150 dBc/Hz at an offset of 600 KHz from the center frequency (@3.7 GHz) for operation using the 1.8 V supply voltage, using moderate inductor-Q values. Monte Carlo simulations were also carried out to determine the effects of the process, voltage and temperature variations.

A NOVEL LOW-VOLTAGE CMOS VARIABLE GAIN AMPLIFIER WITH GAIN-INDEPENDENT INPUT IMPEDANCE MATCHING FOR DTV TUNING APPLICATIONS

2009 ◽  
Vol 18 (06) ◽  
pp. 1119-1136 ◽  
Author(s):  
S. M. REZAUL HASAN
Keyword(s):  
Frequency Band ◽  
Low Voltage ◽  
Noise Figure ◽  
Supply Voltage ◽  
Impedance Matching ◽  
Variable Gain Amplifier ◽  
Control Voltage ◽  
Cmos Process ◽  
Process Technology ◽  
Variable Gain

This paper presents a novel low-voltage single stage CMOS RF Variable Gain Amplifier (RFVGA) designed in 130 nm IBM CMOS process technology using current feed-back gain-independent impedance matching. The proposed RFVGA has a nearly constant gain over the 400 MHz–1 GHz frequency band. Also, it has a 70 dB gain variation (-40 dB to 30 dB) which is decibel-linear within this frequency band for a control voltage in the range of 0.41 V–0.81 V. The RFVGA demonstrates high linearity (THD ≈ -60 dB) and noise immunity (average Noise Figure ≤ 6 dB). It has an input referred third-order intercept point (IIP3) of -1.5 dBm, and an input reflection coefficient (S11) under -8 dB within the frequency band of interest. Also, it dissipates around 5 mW using a 1.2 V power supply. Further, Monte Carlo simulations incorporating process, supply voltage and temperature variations (PVT variations) as well as mismatch between devices (based on width and length of devices) indicate that the design is quite robust. The proposed RFVGA is highly suitable for mobile digital television (DTV) tuner applications.

Power Efficient Implementation of Low Noise CMOS LC VCO using 32nm Technology for RF Applications

2018 ◽  
Vol 6 (8) ◽  
pp. 53
Author(s):  
Shitesh Tiwari ◽  
Sumant Katiyal ◽  
Parag Parandkar
Keyword(s):  
Power Consumption ◽  
Phase Noise ◽  
Tuning Range ◽  
Low Voltage ◽  
Performance Comparison ◽  
Low Noise ◽  
Center Frequency ◽  
Voltage Controlled Oscillator ◽  
Low Phase Noise ◽  
Lc Vco

Voltage Controlled Oscillator (VCO) is an integral component of most of the receivers such as GSM, GPS etc. As name indicates, oscillation is controlled by varying the voltage at the capacitor of LC tank. By varying the voltage, VCO can generate variable frequency of oscillation. Different VCO Parameters are contrasted on the basis of phase noise, tuning range, power consumption and FOM. Out of these phase noise is dependent on quality factor, power consumption, oscillation frequency and current. So, design of LC VCO at low power, low phase noise can be obtained with low bias current at low voltage.  Nanosize transistors are also contributes towards low phase noise. This paper demonstrates the design of low phase noise LC VCO with 4.89 GHz tuning range from 7.33-11.22 GHz with center frequency at 7 GHz. The design uses 32nm technology with tuning voltage of 0-1.2 V. A very effective Phase noise of -114 dBc / Hz is obtained with FOM of -181 dBc/Hz. The proposed work has been compared with five peer LC VCO designs working at higher feature sizes and outcome of this performance comparison dictates that the proposed work working at better 32 nm technology outperformed amongst others in terms of achieving low Tuning voltage and moderate FoM, overshadowed by a little expense of power dissipation. 

Analysis of 6T SRAM Cell in Different Technologies

2017 ◽  
Vol MCSP2017 (01) ◽  
pp. 7-10 ◽  
Author(s):  
Subhashree Rath ◽  
Siba Kumar Panda
Keyword(s):  
Low Power ◽  
Data Storage ◽  
Low Voltage ◽  
Random Access ◽  
Storage Device ◽  
Cmos Process ◽  
Process Technology ◽  
Digital Devices ◽  
Noise Margin ◽  
Sram Cell

Static random access memory (SRAM) is an important component of embedded cache memory of handheld digital devices. SRAM has become major data storage device due to its large storage density and less time to access. Exponential growth of low power digital devices has raised the demand of low voltage low power SRAM. This paper presents design and implementation of 6T SRAM cell in 180 nm, 90 nm and 45 nm standard CMOS process technology. The simulation has been done in Cadence Virtuoso environment. The performance analysis of SRAM cell has been evaluated in terms of delay, power and static noise margin (SNM).

scholarly journals Design Strategies and Architectures for Ultra-Low-Voltage Delta-Sigma ADCs

Electronics ◽  
2021 ◽  
Vol 10 (10) ◽  
pp. 1156
Author(s):  
Lorenzo Benvenuti ◽  
Alessandro Catania ◽  
Giuseppe Manfredini ◽  
Andrea Ria ◽  
Massimo Piotto ◽  
...  
Keyword(s):  
Low Voltage ◽  
Flicker Noise ◽  
Supply Voltage ◽  
Cmos Process ◽  
Clock Frequency ◽  
Design Environment ◽  
Ultra Low Power ◽  
Analog Cmos ◽  
Gain Error ◽  
Dc Gain

The design of ultra-low voltage analog CMOS integrated circuits requires ad hoc solutions to counteract the severe limitations introduced by the reduced voltage headroom. A popular approach is represented by inverter-based topologies, which however may suffer from reduced finite DC gain, thus limiting the accuracy and the resolutions of pivotal circuits like analog-to-digital converters. In this work, we discuss the effects of finite DC gain on ultra-low voltage ΔΣ modulators, focusing on the converter gain error. We propose an ultra-low voltage, ultra-low power, inverter-based ΔΣ modulator with reduced finite-DC-gain sensitivity. The modulator employs a two-stage, high DC-gain, switched-capacitor integrator that applies a correlated double sampling technique for offset cancellation and flicker noise reduction; it also makes use of an amplifier that implements a novel common-mode stabilization loop. The modulator was designed with the UMC 0.18 μm CMOS process to operate with a supply voltage of 0.3 V. It was validated by means of electrical simulations using the CadenceTM design environment. The achieved SNDR was 73 dB, with a bandwidth of 640 Hz, and a clock frequency of 164 kHz, consuming only 200.5 nW. It achieves a Schreier Figure of Merit of 168.1 dB. The proposed modulator is also able to work with lower supply voltages down to 0.15 V with the same resolution and a lower power consumption despite of a lower bandwidth. These characteristics make this design very appealing in sensor interfaces powered by energy harvesting sources.

scholarly journals A 0.3 V Rail-to-Rail Ultra-Low-Power OTA with Improved Bandwidth and Slew Rate

2021 ◽  
Vol 11 (2) ◽  
pp. 19
Author(s):  
Francesco Centurelli ◽  
Riccardo Della Sala ◽  
Pietro Monsurrò ◽  
Giuseppe Scotti ◽  
Alessandro Trifiletti
Keyword(s):  
Low Power ◽  
Low Voltage ◽  
Supply Voltage ◽  
Cmos Process ◽  
Slew Rate ◽  
Large Signal ◽  
Output Stage ◽  
Ultra Low Power ◽  
Input Stage ◽  
Rail To Rail

In this paper, we present a novel operational transconductance amplifier (OTA) topology based on a dual-path body-driven input stage that exploits a body-driven current mirror-active load and targets ultra-low-power (ULP) and ultra-low-voltage (ULV) applications, such as IoT or biomedical devices. The proposed OTA exhibits only one high-impedance node, and can therefore be compensated at the output stage, thus not requiring Miller compensation. The input stage ensures rail-to-rail input common-mode range, whereas the gate-driven output stage ensures both a high open-loop gain and an enhanced slew rate. The proposed amplifier was designed in an STMicroelectronics 130 nm CMOS process with a nominal supply voltage of only 0.3 V, and it achieved very good values for both the small-signal and large-signal Figures of Merit. Extensive PVT (process, supply voltage, and temperature) and mismatch simulations are reported to prove the robustness of the proposed amplifier.

scholarly journals A 219-µW ultra-low power low-noise amplifier for IEEE 802.15.4 based battery powered, portable, wearable IoT applications

2021 ◽  
Vol 3 (4) ◽  
Author(s):  
S. Chrisben Gladson ◽  
Adith Hari Narayana ◽  
V. Thenmozhi ◽  
M. Bhaskar
Keyword(s):  
Low Power ◽  
Ieee 802.15.4 ◽  
Low Voltage ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Cmos Process ◽  
Process Technology ◽  
Ultra Low Power ◽  
Power Mode ◽  
Noise Amplifier

AbstractDue to the increased processing data rates, which is required in applications such as fifth-generation (5G) wireless networks, the battery power will discharge rapidly. Hence, there is a need for the design of novel circuit topologies to cater the demand of ultra-low voltage and low power operation. In this paper, a low-noise amplifier (LNA) operating at ultra-low voltage is proposed to address the demands of battery-powered communication devices. The LNA dual shunt peaking and has two modes of operation. In low-power mode (Mode-I), the LNA achieves a high gain ($$S21$$ S 21 ) of 18.87 dB, minimum noise figure ($${NF}_{min.}$$ NF m i n . ) of 2.5 dB in the − 3 dB frequency range of 2.3–2.9 GHz, and third-order intercept point (IIP3) of − 7.9dBm when operating at 0.6 V supply. In high-power mode (Mode-II), the achieved gain, NF, and IIP3 are 21.36 dB, 2.3 dB, and 13.78dBm respectively when operating at 1 V supply. The proposed LNA is implemented in UMC 180 nm CMOS process technology with a core area of $$0.40{\mathrm{ mm}}^{2}$$ 0.40 mm 2 and the post-layout validation is performed using Cadence SpectreRF circuit simulator.

Design and analysis of a low noise CMOS charge pump phase locked loop circuit

2021 ◽  
pp. 2140002
Author(s):  
Yanbo Chen ◽  
Shubin Zhang
Keyword(s):  
Phase Noise ◽  
Supply Voltage ◽  
Charge Pump ◽  
Phase Locked Loop ◽  
Low Noise ◽  
Cmos Process ◽  
Voltage Controlled Oscillator ◽  
Output Frequency ◽  
Power Supply Voltage ◽  
Supply Noise

Phase Locked Loop (PLL) circuit plays an important part in electronic communication system in providing high-frequency clock, recovering the clock from data signal and so on. The performance of PLL affects the whole system. As the frequency of PLL increases, designing a PLL circuit with lower jitter and phase noise becomes a big challenge. To suppress the phase noise, the optimization of Voltage Controlled Oscillator (VCO) is very important. As the power supply voltage degrades, the VCO becomes more sensitive to supply noise. In this work, a three-stage feedforward ring VCO (FRVCO) is designed and analyzed to increase the output frequency. A novel supply-noise sensing (SNS) circuit is proposed to suppress the supply noise’s influence on output frequency. Based on these, a 1.2 V 2 GHz PLL circuit is implemented in 110 nm CMOS process. The phase noise of this CMOS charge pump (CP) PLL is 117 dBc/Hz@1 MHz from test results which proves it works successfully in suppressing phase noise.

Sign in / Sign up

Export Citation Format

Share Document