PREPARATION AND CHARACTERISTICS OF CO-DOPED HYDROXYAPATITE BIOMIMETIC COATINGS ON PRETREATED Ti6Al4V ALLOY

2020 ◽  
Vol 27 (11) ◽  
pp. 2050012
Author(s):  
TUGCE HACIOGLU ◽  
AYSEN TEZCANER ◽  
SHERIF ABBAS ◽  
ZAFER EVIS

In this study, [Formula: see text] co-doped and pure hydroxyapatites (HAp) were coated on rough surfaces of Ti6Al4V plates by biomimetic method. Prepared samples were investigated with SEM, EDS, FTIR, XRD and ICP. Furthermore, mechanical scratch tests, profilometer tests and in vitro cell studies were carried out. In order to explore the antibacterial characteristics of the coating, the survival rate of a bacteria named Staphylococcus epidermidis was determined. Structural investigations showed that HAp nucleation began four days after the immersion, expectedly nucleation developed collaterally with the incubation period and co-dopants had considerable effect on surface characteristics. Besides, the pretreatment procedure and dopants had notable impact on mechanical qualifications of the coatings. The critical load values obtained for coating failure were detected above 100[Formula: see text]mN in all types of coatings (max. critical load was obtained from 0.3[Formula: see text]mM co-doped coatings). Cancerous bone cells (SaOS-2) on prepared coatings were evaluated in terms of biological properties. 0.1-C7 and 0.3-C7 exhibited highest reduction percentage among all co-doped samples. Further increase in dopants concentrations up to 0.5[Formula: see text]mM lead to increase in toxicity and decrease in cell proliferation. Antibacterial test results showed the most antibacterial samples were 0.1-C7 and 0.3-C7, the results conformed with cell culture findings.

2018 ◽  
Vol 18 (5) ◽  
pp. 757-764 ◽  
Author(s):  
Pravin S. Bhale ◽  
Hemant V. Chavan ◽  
Sakharam B. Dongare ◽  
Sagar T. Sankpal ◽  
Babasaheb P. Bandgar

Background: The blending of two pharmacophores would generate novel molecular templates that are likely to exhibit interesting biological properties. Objective: A facile, efficient and high yielding synthesis of (E)-3-(benzo[d]thiazol-2-ylamino)-2-(1-methyl-1Hindole- 3-carbonyl)-3-(methylthio) acrylonitrile derivatives and evaluation of therapeutic potential. Method: The synthesis of target molecules has been achieved by reacting 2-aminobenzothiazole and substituted 2-(1-methyl-1H-indole-3-carbonyl)-3,3-bis(methylthio)acrylonitrile in the presence of a catalytic amount of sodium hydride in THF. Structural investigations were carried using 1H NMR, 13C NMR, FT-IR, and HRMS data. Results: In vitro anti-tumor evaluation of the synthesized compounds against MCF-7 (breast carcinoma) cell line revealed that they possess good anti-tumor activities. Compounds, 4j and 4i demonstrated significant activities against breast carcinoma (GI50 14.3 and 19.5 µM respectively). Most of the synthesized compounds were also found to be excellent NO, H2O2, DPPH, and superoxide radical scavengers. Anti-diabetic and antiinflammatory evaluation also displayed moderate activity. Conclusion: Among the compounds synthesized some of the compounds possess significant anticancer, antioxidant and anti-inflammatory properties.


2014 ◽  
Vol 86 (12) ◽  
pp. 1911-1922 ◽  
Author(s):  
Hyo Seung Park ◽  
Su Yeon Lee ◽  
Hyunsik Yoon ◽  
Insup Noh

Abstract Design of micro-patterning of hydrogel is of critical importance in both understanding cellular behaviors and mimicking controlled microenvironments and architectures of diverse well-organized tissues. After micro-patterning of hyaluronic acid (HA) hydrogel on a poly(dimethyl siloxane) substrate, its physical and biological properties have been compared with those of a non-patterned hydrogel for its possible applications in bone tissue engineering. The micro-patterned morphologies of HA hydrogel in both swollen and dehydrated forms have been observed with light microscope and scanning electron microscope, respectively, before and after in vitro cell culture. When MC3T3 bone cells were in vitro cultured on both HA hydrogels, the micro-patterned one shows excellence in cell proliferation and lining for 7 days along the micro-pattern paths over those of the non-patterned one, which have shown less cell-adhesiveness. The cytotoxicity of the micro-patterned HA hydrogels was in vitro evaluated by the assays of MTT, BrdU and Neutral red. The viability and morphology of MC3T3 cells on both HA hydrogels were observed with a fluorescence microscope by the live & dead assay, where their viability was confirmed by staining of F-actin development. The results of their H&E staining showed that both micro-patterned and non-patterned hydrogels induced development of tissue regeneration as observed by cell attachment, proliferation, and survivability, but the micro-patterned one induced distinctive patterning of both better initial cells adhesion on the micro-patterns and subsequently development of their proliferation and extracellular matrix, which were considered as important characteristics in their applications to tissue engineering.


2003 ◽  
Vol 795 ◽  
Author(s):  
R. Hoy ◽  
P. van Essen ◽  
J.-D. Kamminga ◽  
G. C. A. M. Janssen ◽  
A. P. Ehiasarian

ABSTRACTHard CrNx coatings of various composition were deposited on hot work tool steel by means of reactive sputter deposition in an industrial PVD reactor. All deposited coatings (thickness 3–4 micron) were under compressive stress. The coatings were subjected to scratch testing with a diamond stylus. Two critical loads were determined. The first critical load, Lc1, indicates the onset of chipping and/or spalling. The second critical load, Lc2, indicates complete coating removal inside the track. Micrographs showing the coating failure are presented. Stoichiomeric CrN coatings outperform understoichiometric CrN0.6 coatings in scratch tests. It was found that for all specimens the coating-to-substrate adhesion is very good, independent on composition. Although the values of Lc1 and Lc2 are distinctly different, their dependence on composition is similar.


1997 ◽  
Vol 323 (3) ◽  
pp. 637-643 ◽  
Author(s):  
XinLi ZHU ◽  
Chun LUO ◽  
Jack M. FERRIER ◽  
Jaro SODEK

Osteopontin (OPN) and bone sialoprotein (BSP) are phosphorylated glycoproteins that, together with osteonectin/secreted protein, acidic, rich in cysteine (SPARC) and osteocalcin, comprise the major non-collagen proteins of bone. Although phosphorylation of OPN and BSP, which is known to influence the biological properties of these proteins, has been shown to occur intracellularly, recent studies have demonstrated ectokinase activity in bone cell populations [Mikuni-Takagaki, Kakai, Satoyoshi, Kawano, Suzuki, Kawase and Saito (1995) J. Bone Miner. Res. 10, 231–241]. To determine whether OPN and BSP are phosphorylated by ectokinase activity we have used [γ-32P]ATP and [γ-32P]GTP as cell-impenetrable phosphate donors to analyse for ectokinase activity in osteoblastic UMR106.06 cells and fetal rat calvarial cells (FRCCs). By pulse-labelling confluent cells with radiolabelled nucleotides, the phosphorylation of endogenous and exogenously added OPN and BSP was demonstrated together with the labelling of a number of cell surface proteins. These phosphorylation reactions were inhibited by a cell-impermeable ectokinase inhibitor, K252b, and cell surface phosphorylation was also inhibited by exogenously added OPN and BSP substrates, indicating competition for the ectokinase enzyme. However, phosphorylation of OPN and BSP, both of which can mediate cell attachment through Arg-Gly-Asp (RGD) motifs, was not inhibited by an RGD peptide, suggesting that binding of OPN and BSP to cell surface integrins is not required. In similar experiments, ectokinase-mediated phosphorylation of OPN and BSP was demonstrated during mineralized tissue formation by FRCCs in vitro. These studies demonstrate that OPN and BSP secreted by bone cells are phosphorylated by a casein kinase II-like ectokinase present on the surface of osteoblastic cells.


2009 ◽  
Vol 1235 ◽  
Author(s):  
Raina Himani Jain ◽  
Shaojie Wang ◽  
Hassan M. Moawad ◽  
Matthias M. Falk ◽  
Himanshu Jain

AbstractBioglass 45S is a promising bone implant material with superior biocompatibility. Past research showed that adhesion of bone cells to titanium is strongly affected by its surface architecture. However, little is known about the role of surface topology of glass on its use as an implant. Thus, we systematically investigated the effect of surface roughness (Ra ∼ 0.01 – 1.2 μm) on cell adhesion and proliferation on 45S Bioglass in vitro. MG63 osteosarcoma and MC3T3 osteoblast precursor cells were seeded on the glass samples, and incubated for up to 6 days. The attachment, morphology and proliferation of cells were investigated using fluorescence microscopy. Our results show that cell attachment (as indicated by cell spreading and number of focal adhesion sites), and proliferation rate decrease with increasing roughness of bioactive glass surface. These findings provide important insight for improving surface characteristics of bioactive glass bone implants.


2006 ◽  
Vol 15 (04) ◽  
pp. 245-257 ◽  
Author(s):  
H. J. Rolf ◽  
K. G. Wiese ◽  
H. Siggelkow ◽  
H. Schliephake ◽  
G. A. Bubernik

2018 ◽  
Vol 69 (6) ◽  
pp. 1416-1418
Author(s):  
Alexandru Szabo ◽  
Ilare Bordeasu ◽  
Ion Dragos Utu ◽  
Ion Mitelea

Hydroxyapatite (HA) is a very common material used for biomedical applications. Usually, in order to improve its poor mechanical properties is combined or coated with other high-strength materials.The present paper reports the manufacturing and the biocompatibility behaviour of two different biocomposite coatings consisting of alumina (Al2O3) and hydroxyapatite (HA) using the high velocity oxygen fuel (HVOF) spraying method which were deposited onto the surface of a commercially pure titanium substrate. The biological properties of the Al2O3-HA materials were evaluated by in vitro studies. The morphology of the coatings before and after their immersing in the simulated body fluid (SBF) solution was characterized by scanning electron microscopy (SEM). The results showed an important germination of the biologic hydroxyapatite crystallite on the surface of both coatings.


2020 ◽  
Vol 28 ◽  
Author(s):  
Justyna Hajtuch ◽  
Karolina Niska ◽  
Iwona Inkielewicz-Stepniak

Background: Cancer along with cardiovascular diseases are globally defined as leading causes of death. Importantly, some risk factors are common to these diseases. The process of angiogenesis and platelets aggregation are observed in cancer development and progression. In recent years, studies have been conducted on nanodrugs in these diseases that have provided important information on the biological and physicochemical properties of nanoparticles. Their attractive features are that they are made of biocompatible, well-characterized and easily functionalized materials. Unlike conventional drug delivery, sustained and controlled drug release can be obtained by using nanomaterials. Methods: In this article, we review the latest research to provide comprehensive information on nanoparticle-based drugs for the treatment of cancer, cardiovascular disease associated with abnormal haemostasis, and the inhibition of tumorassociated angiogenesis. Results: The results of the analysis of data based on nanoparticles with drugs confirm their improved pharmaceutical and biological properties, which gives promising antiplatelet, anticoagulant and antiangiogenic effects. Moreover, the review included in vitro, in vivo research and presented nanodrugs with chemotherapeutics approved by Food and Drug Administration. Conclusion: By the optimization of nanoparticles size and surface properties, nanotechnology are able to deliver drugs with enhanced bioavailability in treatment of cardiovascular disease, cancer and inhibition of cancer-related angiogenesis. Thus, nanotechnology can improve the therapeutic efficacy of the drug, but there is a need for a better understanding of the nanodrugs interaction in the human body, because this is a key factor in the success of potential nanotherapeutics.


2019 ◽  
Vol 20 (4) ◽  
pp. 285-292 ◽  
Author(s):  
Abdullah M. Alnuqaydan ◽  
Bilal Rah

Background:Tamarix Articulata (T. articulata), commonly known as Tamarisk or Athal in Arabic region, belongs to the Tamaricaece species. It is an important halophytic medicinal plant and a good source of polyphenolic phytochemical(s). In traditional medicines, T. articulata extract is commonly used, either singly or in combination with other plant extracts against different ailments since ancient times.Methods:Electronic database survey via Pubmed, Google Scholar, Researchgate, Scopus and Science Direct were used to review the scientific inputs until October 2018, by searching appropriate keywords. Literature related to pharmacological activities of T. articulata, Tamarix species, phytochemical analysis of T. articulata, biological activities of T. articulata extracts. All of these terms were used to search the scientific literature associated with T. articulata; the dosage of extract, route of administration, extract type, and in-vitro and in-vivo model.Results:Numerous reports revealed that T. articulata contains a wide spectrum of phytochemical(s), which enables it to have a wide window of biological properties. Owing to the presence of high content of phytochemical compounds like polyphenolics and flavonoids, T. articulata is a potential source of antioxidant, anti-inflammatory and antiproliferative properties. In view of these pharmacological properties, T. articulata could be a potential drug candidate to treat various clinical conditions including cancer in the near future.Conclusion:In this review, the spectrum of phytochemical(s) has been summarized for their pharmacological properties and the mechanisms of action, and the possible potential therapeutic applications of this plant against various diseases discussed.


2019 ◽  
Vol 19 (8) ◽  
pp. 631-640 ◽  
Author(s):  
Omel Baneen Qallandar ◽  
Faeza Ebrahimi ◽  
Farhadul Islam ◽  
Riajul Wahab ◽  
Bin Qiao ◽  
...  

Background: Co-culture of cancer cells with alveolar bone cells could modulate bone invasion and destructions. However, the mechanisms of interaction between oral squamous cell carcinoma (OSCC) and bone cells remain unclear. Objective: The aim of this study is to analyse the direct and indirect effects of OSCC cells in the stimulation of osteolytic activity and bone invasion. Methods: Direct co-culture was achieved by culturing OSCC (TCA8113) with a primary alveolar bone cell line. In the indirect co-culture, the supernatant of TCA8113 cells was collected to culture the alveolar bone cells. To assess the bone invasion properties, in vitro assays were performed. Results: The proliferation of co-cultured cancer cells was significantly (p<0.05) higher in comparison to the monolayer control cells. However, the proliferation rates were not significantly different between direct and indirect co-cultured cells with indirect co-cultured cells proliferated slightly more than the direct co-cultured cells. Invasion and migration capacities of co-cultured OSCC and alveolar bone cells enhanced significantly (p<0.05) when compared to that of control monolayer counterparts. Most importantly, we noted that OSCC cells directly co-cultured with alveolar bone cells stimulated pronounced bone collagen destruction. In addition, stem cells and epithelialmesenchymal transition markers have shown significant changes in their expression in co-cultured cells. Conclusion: In conclusion, the findings of this study highlight the importance of the interaction of alveolar bone cells and OSCC cells in co-culture setting in the pathogenesis of bone invasion. This may help in the development of potential future biotherapies for bone invasion in OSCC.


Sign in / Sign up

Export Citation Format

Share Document