scholarly journals Multiscale Collaborative Optimization of Processing Parameters for Carbon Fiber/Epoxy Laminates Fabricated by High-Speed Automated Fiber Placement

2016 ◽  
Vol 2016 ◽  
pp. 1-14 ◽  
Author(s):  
Zhenyu Han ◽  
Shouzheng Sun ◽  
Zhongxi Shao ◽  
Hongya Fu
Keyword(s):  
Mechanical Properties ◽  
Strain Energy ◽  
High Speed ◽  
Processing Parameters ◽  
Collaborative Optimization ◽  
Manufacturing Defects ◽  
Fiber Placement ◽  
Automated Fiber Placement ◽  
Processing Optimization ◽  
Carbon Fiber Epoxy

Processing optimization is an important means to inhibit manufacturing defects efficiently. However, processing optimization used by experiments or macroscopic theories in high-speed automated fiber placement (AFP) suffers from some restrictions, because multiscale effect of laying tows and their manufacturing defects could not be considered. In this paper, processing parameters, including compaction force, laying speed, and preheating temperature, are optimized by multiscale collaborative optimization in AFP process. Firstly, rational model between cracks and strain energy is revealed in order that the formative possibility of cracks could be assessed by using strain energy or its density. Following that, an antisequential hierarchical multiscale collaborative optimization method is presented to resolve multiscale effect of structure and mechanical properties for laying tows or cracks in high-speed automated fiber placement process. According to the above method and taking carbon fiber/epoxy tow as an example, multiscale mechanical properties of laying tow under different processing parameters are investigated through simulation, which includes recoverable strain energy (ALLSE) of macroscale, strain energy density (SED) of mesoscale, and interface absorbability and matrix fluidity of microscale. Finally, response surface method (RSM) is used to optimize the processing parameters. Two groups of processing parameters, which have higher desirability, are obtained to achieve the purpose of multiscale collaborative optimization.

scholarly journals Defect Characteristics and Online Detection Techniques During Manufacturing of FRPs Using Automated Fiber Placement: A Review

Polymers ◽  
2020 ◽  
Vol 12 (6) ◽  
pp. 1337 ◽  
Author(s):  
Shouzheng Sun ◽  
Zhenyu Han ◽  
Hongya Fu ◽  
Hongyu Jin ◽  
Jaspreet Singh Dhupia ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Large Scale ◽  
Variable Stiffness ◽  
Future Research ◽  
Online Detection ◽  
Manufacturing Defects ◽  
Manufacturing Method ◽  
Detection Techniques ◽  
Fiber Placement ◽  
Automated Fiber Placement

Automated fiber placement (AFP) is an advanced manufacturing method for composites, which is especially suitable for large-scale composite components. However, some manufacturing defects inevitably appear in the AFP process, which can affect the mechanical properties of composites. This work aims to investigate the recent works on manufacturing defects and their online detection techniques during the AFP process. The main content focuses on the position defect in conventional and variable stiffness laminates, the relationship between the defects and the mechanical properties, defect control methods, the modeling method for a void defect, and online detection techniques. Following that, the contributions and limitations of the current studies are discussed. Finally, the prospects of future research concerning theoretical and practical engineering applications are pointed out.

scholarly journals Review: Filament Winding and Automated Fiber Placement with In Situ Consolidation for Fiber Reinforced Thermoplastic Polymer Composites

Polymers ◽  
2021 ◽  
Vol 13 (12) ◽  
pp. 1951
Author(s):  
Yi Di Boon ◽  
Sunil Chandrakant Joshi ◽  
Somen Kumar Bhudolia
Keyword(s):  
Processing Parameters ◽  
Filament Winding ◽  
Reference Points ◽  
Thermoplastic Composites ◽  
Manufacturing Processes ◽  
Fiber Reinforced ◽  
Consolidation Process ◽  
Fiber Placement ◽  
Automated Fiber Placement

Fiber reinforced thermoplastic composites are gaining popularity in many industries due to their short consolidation cycles, among other advantages over thermoset-based composites. Computer aided manufacturing processes, such as filament winding and automated fiber placement, have been used conventionally for thermoset-based composites. The automated processes can be adapted to include in situ consolidation for the fabrication of thermoplastic-based composites. In this paper, a detailed literature review on the factors affecting the in situ consolidation process is presented. The models used to study the various aspects of the in situ consolidation process are discussed. The processing parameters that gave good consolidation results in past studies are compiled and highlighted. The parameters can be used as reference points for future studies to further improve the automated manufacturing processes.

Postprocessing method-induced mechanical properties of carbon fiber-reinforced thermoplastic composites

2020 ◽  
pp. 089270572094537
Author(s):  
Van-Tho Hoang ◽  
Bo-Seong Kwon ◽  
Jung-Won Sung ◽  
Hyeon-Seok Choe ◽  
Se-Woon Oh ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Carbon Fiber ◽  
Processing Parameters ◽  
Thermoplastic Composites ◽  
Void Content ◽  
Fiber Reinforced ◽  
Crystallinity Degree ◽  
Automated Fiber Placement ◽  
Carbon Fiber Reinforced

Promising carbon fiber-reinforced thermoplastic (CF/polyetherketoneketone (PEKK)) composites were fabricated by the state-of-the-art technology known as “Automated Fiber Placement.” The mechanical properties of CF/PEKK were evaluated for four different postprocessing methods: in situ consolidation, annealing, vacuum bag only (VBO), and hot press (HP). The evaluation was performed by narrowing down the relevant processing parameters (temperature and layup speed). Furthermore, the void content and crystallinity of CF/PEKK were measured to determine the effect of these postprocessing processes. The HP process resulted in the best quality with the highest interlaminar shear strength, highest crystallinity degree, and lowest void content. The second most effective method was VBO, and annealing also realized an improvement compared with in situ consolidation. The correlation between the postprocessing method and the void content and crystallinity degree was also discussed.

Impact of layup rate on the quality of fiber steering/cut-restart in automated fiber placement processes

2015 ◽  
Vol 22 (2) ◽  
pp. 165-173 ◽  
Author(s):  
Jihua Chen ◽  
Teresa Chen-Keat ◽  
Mehdi Hojjati ◽  
AJ Vallee ◽  
Marc-Andre Octeau ◽  
...  
Keyword(s):  
Compaction Pressure ◽  
Experimental Studies ◽  
Process Condition ◽  
Processing Parameters ◽  
Experimental Results ◽  
High Quality ◽  
Fiber Placement ◽  
Automated Fiber Placement

AbstractDeveloping reliable processes is one of the key elements in producing high-quality composite components using an automated fiber placement (AFP) process. In this study, both simulation and experimental studies were carried out to investigate fiber steering and cut/restart under different processing parameters, such as layup rate and compaction pressure, during the AFP process. First, fiber paths were designed using curved fiber axes with different radii. Fiber placement trials were then conducted to investigate the quality of the steered fiber paths. Furthermore, a series of sinusoidal fiber paths were fiber placed and investigated. Moreover, a six-ply laminate with cut-outs in it was manufactured in the cut/restart trials. The accuracy of the fiber cut/restart was compared at different layup rates for both one- and bi-directional layups. Experimental results show that it was possible to layup steered fiber paths with small radii of curvature (minimum 114 mm) designed for this study when the proper process condition was used. It was observed from the cut/restart trials that the quality of tow cut was independent of layup speed; however, the accuracy of tow restart was related to the layup speed. The faster the layup speed, the less accurate was the tow restart.

Heat Built-Up of Industrial Solid Tires in Thailand

2013 ◽  
Vol 844 ◽  
pp. 445-449
Author(s):  
Sanae Rukkur ◽  
Charoenyut Dechwayukul ◽  
Wiriya Thongruang ◽  
Orasa Patarapaiboolchai
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Heat Generation ◽  
Strain Energy ◽  
High Speed ◽  
Cyclic Load ◽  
Hysteresis Loops ◽  
Heavy Load ◽  
Heat Build Up ◽  
Temperature Work

Solid tires made of natural rubber, manufactured and used for forklift trucks in Thailand, have quality problems involving blow out [. Failure of solid tires may occur from excessive loads and or heat generation inducing loss of mechanical properties. The failure of solid tires relating to heat generation is considered. Solid tires under severe conditions, such as overloading, high speed, or high temperature work places often leading to fail and blowout. When these are continuously rolled and loaded, the rubber is stressed and deformed leading to heat generation [. The hysteresis loss storage in form of strain energy due to internal friction in the rubber converts to the heat source transfer to the section of tire. During carrying heavy load, solid tire is subjected to the repeat compressed cyclic loading. Since rubber has the visco-hyperelastic property, cyclic load deformation causes hysteresis loop when tire is performed under cyclic load. Hysteresis loops area indicates the amount of energy turn into heat and it is difficult transferring to the surface of the tire due to insulation itself. As the results, there is heat build-up as shown in term of temperature rising differs in each tire and finally causes blowout or explosion.

scholarly journals Manufacturing-Induced Imperfections in Composite Parts Manufactured via Automated Fiber Placement

2019 ◽  
Vol 3 (2) ◽  
pp. 56 ◽  
Author(s):  
Falk Heinecke ◽  
Christian Willberg
Keyword(s):  
Composite Structures ◽  
Review Paper ◽  
State Of The Art ◽  
Fiber Composite ◽  
Research Gaps ◽  
Manufacturing Defects ◽  
Cycle Times ◽  
Fiber Placement ◽  
Simulation Based ◽  
Automated Fiber Placement

The automated fiber placement process (AFP) enables the manufacturing of large and geometrical complex fiber composite structures with high quality at low cycle times. Although the AFP process is highly accurate and reproducible, manufacturing induced imperfections in the produced composite structure occur. This review summarizes and classifies typical AFP-related manufacturing defects. Several methodologies for evaluating the effects of such manufacturing defects from the literature are reviewed. This review paper presents recent scientific contributions and discusses proposed experimental and simulation-based methodologies. Among the identified ten defect classes, gaps and overlaps are predominant. This paper focuses then on methods for modelling and assessing gaps and overlaps. The state of the art in modelling gaps and overlaps and assessing their influence on mechanical properties is presented. Finally, research gaps and remaining issues are identified.

Characterization of process-induced defects in automated fiber placement manufacturing of composites using fiber Bragg grating sensors

2017 ◽  
Vol 17 (1) ◽  
pp. 108-117 ◽  
Author(s):  
Ebrahim Oromiehie ◽  
B Gangadhara Prusty ◽  
Paul Compston ◽  
Ginu Rajan
Keyword(s):  
Fiber Bragg Grating ◽  
Structural Integrity ◽  
Bragg Grating ◽  
Inspection Method ◽  
Manufacturing Defects ◽  
Fiber Placement ◽  
Fiber Bragg Grating Sensors ◽  
Placement Method ◽  
Automated Fiber Placement ◽  
On Line

With the increasing use of automated fiber placement method for manufacturing highly precise bespoke composite components in the aerospace industry, the level of manufacturing defects within the laminate structure needs to be monitored and minimized for structural integrity. One of the main common defects in automated fiber placement process is misalignment between the tape paths in successive courses which leads to non-integrity of laminate and consequently significant reduction in mechanical strength of the laminate. Therefore, it is necessary to find an appropriate inspection method to monitor and identify these processing defects at the earlier stages of manufacturing. Since optical fiber Bragg grating sensors are being increasingly utilized for structural health monitoring in composite materials and as they were successfully implemented by Oromiehie et al. in their earlier work for on-line lay-up process monitoring, the same methodology is once again tried for identifying the misalignment defects in automated fiber placement process. The experiments are carried out on glass-fiber/nylon laminate with embedded fiber Bragg gratings for the automated tape placement method. The defects due to misalignment are identified by the fiber Bragg grating sensors through their reflected wavelength changes during the automated manufacturing process. The analysis of results indicates that the fiber Bragg grating sensors can be reliably implemented for on-line defect monitoring during the automated fiber placement process to ensure the quality of final product and maintain the expected design life.

scholarly journals Influence of Embedded Gap and Overlap Fiber Placement Defects on Interlaminar Properties of High Performance Composites

Materials ◽  
2021 ◽  
Vol 14 (18) ◽  
pp. 5332
Author(s):  
Denis Cartié ◽  
Marine Lan ◽  
Peter Davies ◽  
Christophe Baley
Keyword(s):  
High Performance ◽  
Crack Arrest ◽  
Shear Loading ◽  
Plane Shear ◽  
Manufacturing Defects ◽  
Fiber Placement ◽  
Out Of Plane ◽  
Beam Shear ◽  
Automated Fiber Placement ◽  
Interlaminar Shear

Automated fiber placement (AFP), once limited to aerospace, is gaining acceptance and offers great potential for marine structures. This paper describes the influence of manufacturing defects, gaps, and overlaps, on the out-of-plane properties of carbon/epoxy composites manufactured by AFP. Apparent interlaminar shear strength measured by short beam shear tests was not affected by the presence of defects. However, the defects do affect delamination propagation. Under Mode I (tension) loading a small crack arrest effect is noted, resulting in higher apparent fracture energies, particularly for specimens manufactured using a caul plate. Under Mode II (in-plane shear) loading there is a more significant effect with increased fracture resistance, as stable propagation for specimens with small gaps changes to arrest with unstable propagation for larger gaps.

Sign in / Sign up

Export Citation Format

Share Document