scholarly journals Investigation of the Application of Various Water Additive Ratios on Unconfined Compressive Strength of Cement-Stabilized Amorphous Peat at Different Natural Moisture Contents

2018 ◽  
Vol 2018 ◽  
pp. 1-9
Author(s):  
Atikah Rahmi ◽  
Siti Noor Linda Taib ◽  
Fauzan Sahdi
Keyword(s):  
Compressive Strength ◽  
Moisture Content ◽  
Unconfined Compressive Strength ◽  
Peat Soil ◽  
Soil Improvement ◽  
Engineering Properties ◽  
Soil Reaction ◽  
Moisture Contents ◽  
Ucs Test ◽  
Cement Soil

Natural peat is considered incapable of supporting built structure due to its poor engineering properties. Chemical stabilization is one of the peat soil improvement methods which has been studied by many researchers. This study describes an investigation of water additive (W/A) ratio application on cement-stabilized peat strength. Peat soil at different moisture contents, which are 1210%, 803%, and 380%, were stabilized with cement by W/A ratio of 2.0, 2.5, 3.0, 3.5, and 4.0. Unconfined compressive strength (UCS) test was conducted after the specimens were being air-cured for 28 and 56 days. The result shows that there is an increase of UCS value as the decrease of W/A ratio (the increase of cement dosage) and the increase of curing time and peat moisture content. The higher strength found in the specimen with higher moisture content, compared to the lower one at the same W/A ratio, shows that the mix design of cement-stabilized peat using W/A ratio should have differed under different peat natural moisture contents. From the result, it is also found that cement hydrolysis reaction occurred despite the presence of humic acid in the peat soil, which by many studies is assumed will hinder the cement-soil reaction.

Strength Test Research on Cement-Soil of Peat Soil in Kunming

2015 ◽  
Vol 730 ◽  
pp. 15-20
Author(s):  
Song Gao ◽  
Hui Min Zhao ◽  
Jing Cao ◽  
Zhi Gang Song
Keyword(s):  
Compressive Strength ◽  
Unconfined Compressive Strength ◽  
Peat Soil ◽  
Strength Test ◽  
Engineering Properties ◽  
Mixing Ratio ◽  
Curve Approximation ◽  
Logarithmic Curve ◽  
Compressive Strength Test ◽  
Cement Soil

Based on the engineering properties of the peat soil in Kunming, through indoor unconfined compressive strength test in this article, and changing the different cement mixing ratio including 12%, 15%, 18%, 21%, 24% and 27% and age including 3 d, 7 d, 14 d, 28 d, 60 d and 90 d, and we focus on the influence on unconfined compressive strength of cement-soil by both of them. Through the study of the regression analysis of test results, we obtain the basic strength characteristics of cement-soil of peat soil which is that cement-soil unconfined compressive strength increases with group of the cement mixing ratio and age and showing a good correlation between them. And the unconfined compressive strength of cement-soil with the increase of ratio presents approximate linear growth and a logarithmic curve approximation along with the age growth, and the growth rate is smaller and smaller.

Strength and Elastic Properties of Cassava Tuber

2007 ◽  
Vol 3 (5) ◽  
Author(s):  
Oladele Peter Kolawole ◽  
Leo Ayodeji Sunday Agbetoye ◽  
A. S. Ogunlowo
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Moisture Content ◽  
Elastic Properties ◽  
Engineering Properties ◽  
Under Five ◽  
Moisture Contents ◽  
Spring Balance

In this study, some engineering properties of cassava tuber samples were determined experimentally under five moisture content levels of 70 %, 65 %, 60%, 55 %, and 50 %wet basis. The properties measured were tensile strength, compressive strength and elasticity. Three experimental tools were designed and fabricated using spring balance, hose-clips, and 12Volts motor with reels and rope for the investigations. The IITA improved cassava variety TMS 4(2) 1425 was used in the experiments. Results of the tests indicated that all the properties measured were influenced by the moisture contents of the tuber.

scholarly journals Using Steel Slag for Stabilizing Clayey Soil in Sulaimani City-Iraq

2020 ◽  
Vol 26 (7) ◽  
pp. 145-157
Author(s):  
Zozk Kawa Abdalqadir ◽  
Nihad Bahaaldeen Salih ◽  
Soran Jabbar Hama Salih
Keyword(s):  
Compressive Strength ◽  
Moisture Content ◽  
Unconfined Compressive Strength ◽  
Clayey Soil ◽  
Steel Slag ◽  
Swelling Pressure ◽  
Geotechnical Properties ◽  
California Bearing Ratio ◽  
Engineering Properties ◽  
Clayey Soils

The clayey soils have the capability to swell and shrink with the variation in moisture content. Soil stabilization is a well-known technique, which is implemented to improve the geotechnical properties of soils. The massive quantities of waste materials are resulting from modern industry methods create disposal hazards in addition to environmental problems. The steel industry has a waste that can be used with low strength and weak engineering properties soils. This study is carried out to evaluate the effect of steel slag (SS) as a by-product of the geotechnical properties of clayey soil. A series of laboratory tests were conducted on natural and stabilized soils. SS was added by 0, 2.5, 5, 10, 15, and 20% to the soil. The conducted tests are consistency limits, specific gravity, hydrometer analysis, modified Proctor compaction, swelling pressure, swelling percent, unconfined compressive strength, and California Bearing Ratio (Soaked CBR). The results showed that the values of liquid limit, plasticity index, optimum moisture content, swelling pressure, and swelling percent were decreased when stabilized the soil. However, the values of maximum dry density, unconfined compressive strength, and California bearing ratio were increased with the addition of steel slag with various percentages to the clayey soil samples. The steel slag was found to be successfully improving the geotechnical properties of clayey soils.

Laboratory Investigation on the Strength Characteristics of Cement-Treated Base

2014 ◽  
Vol 507 ◽  
pp. 353-360 ◽  
Author(s):  
Amiruddin Ismail ◽  
Mojtaba Shojaei Baghini ◽  
Mohamed Rehan Karim ◽  
Foad Shokri ◽  
Ramez A. Al-Mansob ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Moisture Content ◽  
Unconfined Compressive Strength ◽  
Resilient Modulus ◽  
Tension Test ◽  
Engineering Properties ◽  
Dry Density ◽  
Flexure Strength ◽  
Indirect Tension ◽  
Indirect Tension Test

Cement-Treated Base (CTB) is a non-conventional method used in road bases materials to improve its engineering properties due to the hardening of cement when moisture is present and extends the period of curing times. This study investigates the effects of cement additive on properties of base layer using laboratory mechanistic evaluation of stabilized soil mixtures. Laboratory tests conducted were Unconfined Compressive Strength (UCS), Indirect Tension test for Resilient Modulus (ITRM) and Flexure Strength (FS) tests. The results revealed that by adding Portland cement, the mechanical properties of the mixture have improved where the UCS is found to be an important quality indicator. In addition, the variables that influenced these tests, which are cement content, curing time, moisture content, and dry density, play important role to determine the performance of CTB. This paper presents the finding of a correlation conducted to analyse the influences of these variables using regression and ANOVA to establish significant models with the aim of predicting the strength base on mixture parameters. Keywords: Cement-Treated Base, Unconfined Compressive Strength, Indirect Tension test for Resilient Modulus, Flexure Strength, Moisture Content, Dry Density, Regression Analysis.

scholarly journals Assessment of compressive strength of peat soil with sawdust and Rice Husk Ash (RHA) with hydrated lime as additive

2019 ◽  
Vol 258 ◽  
pp. 01014
Author(s):  
Noorfaizah Hamzah ◽  
Nur ‘Ain Mat Yusof ◽  
Muhammad Ihsan Haziq Mohd Rahimi
Keyword(s):  
Compressive Strength ◽  
Rice Husk ◽  
Soil Stabilization ◽  
Rice Husk Ash ◽  
Soft Soil ◽  
Peat Soil ◽  
Hydrated Lime ◽  
Soil Improvement ◽  
Engineering Properties ◽  
Strength Capacity

Construction activities on peat soils are found to be extremely difficult as the soil is profound as soft soil and has low shear strength and high moisture content. Due to alternating swelling and shrinkage nature, it causes serious damage to the structure above it. This happens due to repetition of drying and wetting of soil. Stabilization of soil is commonly applied to improve the mechanical properties of soil prior to soil engineering works. This soil improvement method is advantageous and effective one by using waste materials. Waste in our country is divided in various types and it includes domestic wastes, industrial wasters, agricultural wastes etc. Because of difficulties to diminish these wastes without affect to environment and surroundings, it can be used as a stabilizing agent in the soil. Therefore, this experimental study carried out to evaluate the effect of Rice Husk Ash (RHA) and sawdust on engineering properties of the peat soil. The properties such as compaction and unconfined compressive strength are determined separately with sawdust and added of RHA in peat soil at a variety of percentages (2.5%, 5% etc.) in addition small amount of constant rate of lime with 2% of the dry soil weight. By obtaining the results, it can deduce a promising and improving result in stabilizing the soil with sawdust and Rice Husk Ash in both economic and strength capacity. This will not only solve the waste disposal problem but also enhance the strength characteristics of soil significantly.

scholarly journals Effect of Waste Tire Reinforcement with and without Cement Additives on Peat Strength Improvement

2021 ◽  
Vol 411 ◽  
pp. 121-133
Author(s):  
Nur Amalina Hilwane ◽  
Norazzlina M. Sa’don ◽  
Abdul Razak Abdul Karim
Keyword(s):  
Compressive Strength ◽  
Shear Stress ◽  
Moisture Content ◽  
Unconfined Compressive Strength ◽  
Ground Improvement ◽  
Optimum Moisture Content ◽  
Scrap Tire ◽  
Waste Tire ◽  
Ucs Test ◽  
Shear Box

This paper presents the peat ground improvement techniques using waste-tire as a fibre reinforced material. In this study, two sizes of the waste-tire are chosen, which are 0.05 mm and 1-3 mm, respectively. The collected peat is classified as Sapric peat with the degree of decomposition of H7 based on von Post classification with high moisture content of 400% was recorded. The Sapric peat is treated with the waste-tire at designated percentages of 5%, 10% and 15% with the addition of 5% of cement acting as a binder. The untreated and treated peat without and with cement content are compacted at the optimum moisture content for both the Unconfined Compressive Strength (UCS) test and Direct Shear Box Test. The specimens were air-cured for 7, 28, 56, and 90 days. Hypothetically, higher percentages of rubber improve the shear stress value of the treated peat. According to the results the finer size (0.05mm) of the tire produces a higher shear stress, which may due the finer sizes of the waste-tire filled the void between the soil particles. Further, from the 90 days of curing UCS results, there is a significant increase in compressive strength with the increase percentage of the waste-tire peat mixed samples. In summary, soil stabilized by the scrap-tire is believed to decrease the optimum moisture content and the maximum dry densities, but it helps in increasing the unconfined compressive strength value. Stabilizing by using the tire wastes not only increasing the strength of the soil, but it also helps in reducing the disposal problems.

scholarly journals Peat Stabilization using Gypsum and Fly Ash

2010 ◽  
Vol 1 (2) ◽  
pp. 1-5 ◽  
Author(s):  
Kolay P.K. ◽  
Pui M.P.
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Unconfined Compressive Strength ◽  
Peat Soil ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Compressive Strength Test ◽  
Proctor Test ◽  
Ucs Test ◽  
Standard Proctor Test

This paper presents the stabilization of local peat soil from Matang, Sarawak, using gypsum and fly ash. Peat soil has been identified as one of the major groups of soils found in Malaysia, which has high compressibility and low shear strength. Presence of soft or peaty soil is a major problem encountered by civil engineers in Sarawak. Different percentages of gypsum (i.e., 2, 4, 6 and 8%) and fly ash (i.e., 5, 10, 15, 20 and 25%) were added into peat soil at optimum moisture content and it’s maximum dry density determined by standard Proctor test. Unconfined compressive strength (UCS) test were conducted to determine the strength gain after 7, 14 and 28 days of curing periods. Physical properties of the peat soil have also been studied for identification and classification purposes. The unconfined compressive strength test results show that the peat soil gained strength due to the addition of different percentages of admixtures such as gypsum and fly ash and the strength also increases with the increase of curing periods.

scholarly journals Experimental Study on Improvement of Marine Soft Soil with Alkali Residue

2018 ◽  
Vol 53 ◽  
pp. 04021
Author(s):  
SHAO Yong ◽  
LIU Xiao-li ◽  
ZHU Jin-jun
Keyword(s):  
Experimental Study ◽  
Compressive Strength ◽  
Unconfined Compressive Strength ◽  
Void Ratio ◽  
Soft Soil ◽  
Compressive Modulus ◽  
Engineering Properties ◽  
Test Results ◽  
Use Of Resources ◽  
One Year

Industrial alkali slag is the discharge waste in the process of alkali production. About one million tons of alkali slag is discharged in China in one year. It is a burden on the environment, whether it is directly stacked or discharged into the sea. If we can realize the use of resources, it is a multi-pronged move, so alkali slag is used to improve solidified marine soft soil in this paper. The test results show that the alkali residue can effectively improve the engineering properties of marine soft soil. Among them, the unconfined compressive strength and compressive modulus are increased by about 10 times, and the void ratio and plasticity index can all reach the level of general clay. It shows that alkali slag has the potential to improve marine soft soil and can be popularized in engineering.

Correlation of Unconfined Compressive Strength and California Bearing Ratio in Laterite Soil Stabilization Using Varied Zeolite Content Activated by Waterglass

2020 ◽  
Vol 998 ◽  
pp. 323-328
Author(s):  
Achmad Bakri Muhiddin ◽  
Marthen M. Tangkeallo
Keyword(s):  
Compressive Strength ◽  
Unconfined Compressive Strength ◽  
Soil Stabilization ◽  
Dry Weight ◽  
Engineering Properties ◽  
High Plasticity ◽  
Curing Time ◽  
Laterite Soil ◽  
Zeolite Content ◽  
Meta Silicate

In remote areas, most roads still use pavements that are very sensitive to climate change, especially those using clay pavements with high plasticity. In addition to the issue of cost, the difficulty of obtaining a proper source of material is another problem that has led to soaring prices for materials. In this regard, a study was conducted using local materials, namely zeolite as a stabilizing material added with waterglass as activating agent. The research began with samples of laterite soil and natural zeolite for XRD test (microstructure testing), and then testing for laterite soil’s index properties and engineering properties, namely Unconfined Compressive Strength and CBR value. The purpose of the test is to determine the correlation between the Unconfined Compressive Strength (UCS) and the soil bearing capacity (CBR) caused by adding zeolite as stabilizer material and waterglass as activator with increasing curing time. Laterite soils contain a brownish red iron oxide. The stabilizing material zeolite contains a crystalline mineral of alumina silicate SiO2. While waterglass composed of sodium meta silicate. Stabilization carried out by mixing 4%, 8%, 12%, 16%, and 20% of zeolite with addition of 2% waterglass, percentage was measured based on soil dry weight. Specimens were tested at curing time of 0, 7, 14, and 28 days. The test result shows increasing UCS and CBR values with increasing percentage of zeolite. At mix of 20% zeolite and 2% waterglass, the unconfined compressive strength reaches 23.54 kg/cm2 with CBR value 58% at 28 days of curing time.

Research on the Strength Growth Model of Peat Soil

2014 ◽  
Vol 1030-1032 ◽  
pp. 860-863
Author(s):  
Jing Wei Wang ◽  
Wen Pan ◽  
Zhuo Yin Jiang
Keyword(s):  
Compressive Strength ◽  
Growth Model ◽  
Unconfined Compressive Strength ◽  
Peat Soil ◽  
Curing Agent ◽  
Construction Waste

The Dian Lake Peat soil is studied as the research object in this paper, through the strengthening treatment by adding the cement and some suitable additives as well as a certain amount of waste residue, the compressive strength are taken into consideration in comparison in the different curing composition and other factors in performance of solidified soil. And it importantly discussed the applicability of curing agent and different variables (cement, the formula of curing agent, construction waste, age) in the incremental changes of unconfined compressive strength of curing peat soil.

Sign in / Sign up

Export Citation Format

Share Document