scholarly journals Numerical Investigation of Influences of Drilling Arrangements on the Mechanical Behavior and Energy Evolution of Coal Models

2018 ◽  
Vol 2018 ◽  
pp. 1-12 ◽  
Author(s):  
Tong-bin Zhao ◽  
Wei-yao Guo ◽  
Feng-hai Yu ◽  
Yun-liang Tan ◽  
Bin Huang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Energy Dissipation ◽  
Mechanical Behavior ◽  
Rock Burst ◽  
Test Results ◽  
Energy Index ◽  
Energy Evolution ◽  
Compression Tests ◽  
Influencing Mechanism ◽  
Drilling Method

Destress drilling method is one of the commonly used methods for mitigating rock bursts, especially in coal mining. To better understand the influences of drilling arrangements on the destress effect is beneficial for rock burst mitigation. This study first introduced the rock burst mitigation mechanism of the destress drilling method and then numerically investigated the influences of drilling arrangements on the mechanical properties of coal models through uniaxial compression tests. Based on the test results, the energy evolution (i.e., the energy dissipation and bursting energy indexes) influenced by different drilling arrangements was analyzed. When the drilling diameter, the number of drilling holes in one row, or the number of drilling rows increases, the bearing capacity of specimens nonlinearly decreases, but the energy dissipation index increases. In addition, the drilling diameter or the number of drilling holes in one row affects the failure mode weakly, which is different from that of the number of drilling rows. Consequently, the bursting energy index decreases as increasing the drilling diameter or the number of drilling holes in one row, but as increasing the number of drilling rows, the variation law of bursting energy index is not obvious. At last, the influencing mechanism of drilling arrangement on the rock burst prevention mechanism of the destress drilling method was discussed and revealed.

scholarly journals Mechanical behavior of frozen soil improved with sulphoaluminate cement and its microscopic mechanism

2020 ◽  
Vol 10 (1) ◽  
Author(s):  
Zhenhua Yin ◽  
Hu Zhang ◽  
Jianming Zhang ◽  
Mingtang Chai
Keyword(s):  
Mechanical Properties ◽  
Mechanical Behavior ◽  
Soil Improvement ◽  
Particle Size Analysis ◽  
Frozen Soil ◽  
Size Analysis ◽  
Permafrost Soil ◽  
Compression Tests ◽  
Microscopic Mechanism ◽  
Sulphoaluminate Cement

Abstract The foundation of constructions built in the permafrost areas undergo considerable creeping or thawing deformation because of the underlying ice-rich permafrost. Soil improvement may be of advantage in treating ice-rich permafrost at shallow depth. Sulphoaluminate cement was a potential material to improve frozen soil. Simultaneously, two other cements, ordinary Portland cement and Magnesium phosphate cement were selected as the comparison. The mechanical behavior of modified frozen soil was studied with thaw compression tests and unconfined compression strength tests. Meanwhile, the microscopic mechanism was explored by field emission scanning electron microscopy, particle size analysis and X-ray diffractometry. The results showed Sulphoaluminate cement was useful in reducing the thaw compression deformation and in enhancing the strength of the frozen soil. The improvement of the mechanical behavior depended mainly on two aspects: the formation of structural mineral crystals and the agglomeration of soil particles. The two main factors contributed to the improvement of mechanical properties simultaneously. The thicker AFt crystals result in a higher strength and AFt plays an important role in improving the mechanical properties of frozen soils.The study verified that Sulphoaluminate cement was an excellent stabilizer to improve ice-rich frozen soils.

scholarly journals Comparison of Mechanical Behavior and Acoustic Emission Characteristics of Three Thermally-Damaged Rocks

Energies ◽  
2018 ◽  
Vol 11 (9) ◽  
pp. 2350 ◽  
Author(s):  
Jun Peng ◽  
Sheng-Qi Yang
Keyword(s):  
Mechanical Properties ◽  
Acoustic Emission ◽  
Mechanical Behavior ◽  
Thermal Damage ◽  
Strain Curve ◽  
Treatment Temperature ◽  
P Wave ◽  
High Temperature Treatment ◽  
High Porosity ◽  
Compression Tests

High temperature treatment has a significant influence on the mechanical behavior and the associated microcracking characteristic of rocks. A good understanding of the thermal damage effects on rock behavior is helpful for design and stability evaluation of engineering structures in the geothermal field. This paper studies the mechanical behavior and the acoustic emission (AE) characteristic of three typical rocks (i.e., sedimentary, metamorphic, and igneous), with an emphasis on how the difference in rock type (i.e., porosity and mineralogical composition) affects the rock behavior in response to thermal damage. Compression tests are carried out on rock specimens which are thermally damaged and AE monitoring is conducted during the compression tests. The mechanical properties including P-wave velocity, compressive strength, and Young’s modulus for the three rocks are found to generally show a decreasing trend as the temperature applied to the rock increases. However, these mechanical properties for quartz sandstone first increase to a certain extent and then decrease as the treatment temperature increases, which is mainly attributed to the high porosity of quartz sandstone. The results obtained from stress–strain curve, failure mode, and AE characteristic also show that the failure of quartz-rich rock (i.e., quartz sandstone and granite) is more brittle when compared with that of calcite-rich rock (i.e., marble). However, the ductility is enhanced to some extent as the treatment temperature increases for all the three examined rocks. Due to high brittleness of quartz sandstone and granite, more AE activities can be detected during loading and the recorded AE activities mostly accumulate when the stress approaches the peak strength, which is quite different from the results of marble.

Stabilization of clayey subgrade with waste pumice for road infrastructure

2015 ◽  
Vol 22 (5) ◽  
Author(s):  
Ömür Çimen ◽  
Mehmet Saltan ◽  
S. Nilay Keskin
Keyword(s):  
Mechanical Properties ◽  
Road Construction ◽  
High Plasticity ◽  
Test Results ◽  
Index Properties ◽  
Compression Tests ◽  
Unconfined Compression ◽  
Swelling Potential ◽  
Project Costs ◽  
High Plasticity Clay

AbstractHigh-plasticity clayey subgrade, which is unsuitable for road construction, may sometimes occur along highway routes. In such cases, engineers need to change the route of a highway project, resulting in an increase in road length and project costs. In this study, waste pumice was examined for stabilization of high-plasticity clayey subgrade, which is inappropriate for road construction. For this purpose, the physical and index properties of clay and pumice were determined. Then, the pumice was mixed with high plasticity clay at different ratios by weight. By performing standard Proctor compaction tests on the mixtures, the effects of adding pumice on compaction were also studied. Unconfined compression tests and California bearing ratio (CBR) tests were performed on all pumice-clay mixtures, and the test results and the CBR ratios were compared for each sample, respectively. The results showed that pumice stabilization improved the mechanical properties and reduced the swelling potential of high plasticity clayey subgrade.

Behaviors of Xiashu Loess in the Lower Reaches of China’s Yangtze River under Triaxial Compression and the Microscopic Explanations

2016 ◽  
Vol 858 ◽  
pp. 91-97
Author(s):  
Jun Hua Xiao ◽  
Wen Qi Zheng
Keyword(s):  
Mechanical Properties ◽  
Yangtze River ◽  
Shear Failure ◽  
Triaxial Compression ◽  
Processing Technique ◽  
Point Of View ◽  
Image Processing Technique ◽  
Test Results ◽  
Compression Tests ◽  
Triaxial Compression Tests

To investigate the macroscopic mechanical properties of undisturbed structural Xiashu loess in the lower reaches of China’s Yangtze River under triaxial compression, and obtain the intrinsic explanations for the macroscopic mechanical properties from the microscopic point of view, in laboratory, triaxial compression tests were carried out, microstructure images of sheared samples were collected by scanning electron microscope (SEM), and quantitative parameters of microstructure (mainly about particle or pore size, distribution, and alignment) were extracted by digital image processing technique. Based on the test results, the deviator stress-strain relationships of both undisturbed and remoulded Xiashu loess, the structural strength, and the microstructural evolution mechanism about the formation of shear failure zone of Xiashu loess under triaxial compression were analyzed.

scholarly journals Effects of coal's initial macro-cracks on rockburst tendency of rock–coal composite samples

2019 ◽  
Vol 6 (11) ◽  
pp. 181795 ◽  
Author(s):  
Shaojie Chen ◽  
Dawei Yin ◽  
Huimin Liu ◽  
Bing Chen ◽  
Ning Jiang
Keyword(s):  
Energy Dissipation ◽  
Elastic Energy ◽  
Composite System ◽  
Structural Instability ◽  
Uniaxial Loading ◽  
Test Results ◽  
Compression Tests ◽  
Loading Direction ◽  
Attenuation Index ◽  
Composite Samples

In the present study, uniaxial compression tests were conducted on sandstone–coal composite samples to investigate the effects of original macro-cracks in coal on the rockburst tendency. First, the energy dissipation theory was used to derive the elastic energy attenuation index of composite samples during uniaxial loading. Then, based on the test results obtained, the rockburst tendency of composite samples was evaluated and analysed using the uniaxial compressive strength and elastic energy attenuation index. The results show that the original macro-cracks in coal deteriorated the rockburst tendency of composite samples. The original horizontal cracks had the lowest effect on the rockburst tendency, whereas the vertical penetrating cracks through the coal centre (parallel to the loading direction) displayed the greatest effect. The mechanism by which these macro-cracks weakened the rockburst tendency involved two steps: (i) changing the physical properties and energy accumulation conditions of composite samples and (ii) increasing the energy dissipation of composite samples during uniaxial loading. These aspects are important to understand the rockburst hazards induced by the structural instability and failure of the composite system of coal seam and roof rock during deep coal mining.

Mechanical Properties of Bulk Nanocrystalline Silver-Using Compression Tests

2010 ◽  
Vol 152-153 ◽  
pp. 1313-1316
Author(s):  
Guo Jun Hu ◽  
Zhi Quan Hong
Keyword(s):  
Mechanical Properties ◽  
Coarse Grained ◽  
Strain Rates ◽  
Test Results ◽  
Compression Tests ◽  
Static Test ◽  
Rate Dependent ◽  
Average Grain Size ◽  
Bulk Nanocrystalline ◽  
The Relationship

In this paper, the compression test on the bulk nanocrystalline sliver ( n Ag) with average grain size of 50 nm was made. The stress-strain curves under different strain rates were obtained by test. The test results show that the mechanical behavior of n Ag is rate-dependent, and the dynamic compress yield stress are about 1.5 times of that n Ag in static test condition; The effect of strain harding on n Ag is smaller than that of coarse-grained silver (c Ag) in plastic deformation; The relationship between the yield strength and the logarithm of strain rate is approximately linear.

Buckling Restrained Brace With Inspection Windows

2015 ◽  
Author(s):  
C. S. Tsai ◽  
Yi Liu ◽  
B. Q. Liu
Keyword(s):  
Experimental Study ◽  
Energy Dissipation ◽  
Mechanical Behavior ◽  
Low Cycle Fatigue ◽  
Fatigue Tests ◽  
Test Results ◽  
Cycle Fatigue ◽  
Buckling Restrained Brace ◽  
Steel Core ◽  
Testing Protocols

The buckling restrained brace (BRB) has been worldwide recognized as an energy absorber to protect structures from earthquake damage. However, the traditional BRB is a fully close design, it is therefore impossible to detect the condition of the steel core during manufacturing and after earthquakes. This paper proposed a buckling restrained brace with inspection windows that allow inspecting the condition of the internal components of the BRB. Experimental study in selecting the sizes and locations of the inspection windows without affecting the functionality of the BRB has been carried out to search for an economically feasible BRB that is convenient for manufacturing and installation and meets testing protocols. Test results of the proposed BRBs under cyclic loadings showed that the mechanical behavior of the BRB with inspection windows on the buckling-restraining unit consisting of the constraining and lateral support elements was stable and that damage always occurred at the energy dissipation segments after low cycle fatigue tests. These test results indicate that the inspection windows opened on the proposed BRB have little influence on the strength of the device and that the proposed device can be considered as a stable energy dissipation device.

Behavior of Cemented Reticulate Red Clay

2012 ◽  
Vol 446-449 ◽  
pp. 1666-1669 ◽  
Author(s):  
Jian Zhong Li ◽  
Li Chun Zhuo ◽  
Xi Ni
Keyword(s):  
Mechanical Properties ◽  
Shear Strength ◽  
Cement Content ◽  
Axial Strain ◽  
Test Results ◽  
Compression Tests ◽  
Red Clay ◽  
Reticulate Red Clay ◽  
Strain Deviator ◽  
Relationship Of

Mechanical properties of cemented reticulate red clay were studied in present research. Test results show that: (1) shear strength of cemented reticulate red clay increase exponentially as the increasing of cement content; (2) shear strength of cemented reticulate red clay decrease polynomially as the increasing of water content; (3) mechanical properties of cemented reticulate red clay affected significantly by curing time and curing confined pressure. In order to study viscous properties of cemented reticulate red clay, cemented reticulate red clay specimens were compressed in triaxial chamber at different shear rate. Results of the compression tests show that it is obvious that the axial strain-deviator stress relationship of cemented reticulate red clay affects by the strain rate.

Mechanical Properties of Non-Cement Polymer Grout

2015 ◽  
Vol 1113 ◽  
pp. 80-85
Author(s):  
S.M. Nuria ◽  
A.B.A. Rahman ◽  
N.A.K. Hafizah ◽  
Yusof Ahmad ◽  
Azlan Adnan ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Polyester Resin ◽  
Unsaturated Polyester ◽  
Fine Sand ◽  
Strength Properties ◽  
Test Results ◽  
Compression Tests ◽  
Rapid Setting

This paper studies the effects of binder and filler composition to the strength properties of non-cement polyester grout (NCPG). The binder consisted of unsaturated polyester resin whereas the filler consisted of fine sand and fly ash. The composition of binder-to-filler ratios investigated were 0.43, 0.67, 1, 1.49, and 2.3. The mechanical properties of NCPG were investigated through flowability and compression tests. The test results show that the use of polyester resin combined with fine sand and fly ash produces good quality grout with high flowable rate, rapid setting, self-consolidating and high compressive strength.

Experimental Study on Mechanical Properties of Large NiTi Superelastic Shape Memory Alloy Bars

2021 ◽  
Author(s):  
Qiujun Ning ◽  
Lihua Zhu ◽  
Wei Han ◽  
Cheng Zhao
Keyword(s):  
Mechanical Properties ◽  
Energy Dissipation ◽  
Shape Memory Alloy ◽  
Shape Memory ◽  
Mechanical Performance ◽  
Engineering Application ◽  
Test Results ◽  
Equivalent Viscous Damping ◽  
Heat Treated ◽  
Strength And Stiffness

Abstract This study intensively examined the mechanical properties of large-sized superelastic shape memory alloy (SMA) bars, mainly focusing on their self-centering and energy dissipation capabilities. A detailed investigation on the effects of the heat treatment strategy, loading rate, strain amplitude, cyclic loading, prestress, and diameter of the SMA bars on their mechanical performance—residual strain, energy dissipation, equivalent viscous damping ratios, strength, and stiffness—was conducted. Furthermore, the fracture microstructure of monotonic tensile specimens was analyzed via scanning electron microscopy. The results indicated that the optimally heat-treated SMA bars show good superelasticity. The mechanical properties were relatively stable under constant strain loading–unloading training, which should be considered in engineering applications. The test results provided basic experimental data support for the engineering application of large SMA bars.

Sign in / Sign up

Export Citation Format

Share Document