scholarly journals Shear Characteristics of Cement-Stabilized Sand Reinforced with Waste Polyester Fiber Fabric Blocks

2019 ◽  
Vol 2019 ◽  
pp. 1-12 ◽  
Author(s):  
Xiangfeng Lv ◽  
Hongyuan Zhou
Keyword(s):  
Low Cost ◽  
Triaxial Compression ◽  
Friction Angle ◽  
Polyester Fiber ◽  
Peak Strain ◽  
Compression Tests ◽  
Initial Stiffness ◽  
Cemented Sand ◽  
Aspect Ratios ◽  
Fiber Fabric

The present paper is devoted to investigate the effects of waste polyester fiber fabric blocks on the strength and mechanical behavior of cemented sand. In the investigation, samples were prepared at four different percentages of waste polyester fiber fabric block content (0.0%, 0.5%, 1.0%, and 1.5% by weight of soil) and two different aspect ratios (2 : 1 and 3 : 1), and conventional triaxial compression tests were carried out after the curing period. The test results indicated that the addition of fibers increased peak and residual shear strengths of cemented sand and changed its brittle behavior to a more ductile one. As the fabric block content increased, the brittleness index and initial stiffness decreased, and the peak strain and internal friction angle increased. The optimal combination of the content and aspect ratio was determined to be 0.5% and 3 : 1. The integration of the fabric blocks with the cemented sand matrix was analyzed by using the scanning electron microscopy (SEM). It is found that the reinforcement effect is related to the bond strength and friction at the interface. The micromechanical properties of the fiber/matrix interface were influenced by the undulations between the fabric block components. In summary, this study presented a low-cost and environment-friendly method for reinforcing cement-stabilized sand.

scholarly journals Stress-dependent behavior of saturated clay

2012 ◽  
Vol 49 (8) ◽  
pp. 907-916 ◽  
Author(s):  
Naeem O. Abdulhadi ◽  
John T. Germaine ◽  
Andrew J. Whittle
Keyword(s):  
Stress Level ◽  
High Pressures ◽  
Large Strain ◽  
Triaxial Compression ◽  
Friction Angle ◽  
Peak Strain ◽  
Compression Tests ◽  
Stress Strain ◽  
Stress Dependent ◽  
Undrained Shear

A program of K0-consolidated undrained triaxial compression tests has been performed to investigate the effects of consolidation stress level on the compression and shear behavior of resedimented Boston blue clay (RBBC). Specimens were consolidated to maximum vertical effective stresses in the range 0.15–10 MPa and tested at three overconsolidation ratios (OCR): 1, 2, and 4. The results show that the virgin compression curves are essentially linear in e–log[Formula: see text] space over the consolidation stress range. However, the normally consolidated K0 stress ratio increases with the level of consolidation stress. The stress–strain–strength properties measured in undrained shear are significantly affected by the consolidation stress level at each OCR and show indications of non-normalizable behavior. At high pressures, the undrained shear stress–strain behavior becomes more ductile, requiring larger strains to mobilize peak resistance and exhibiting less post-peak strain-softening. The undrained strength ratio (su/[Formula: see text]) is not uniquely controlled by OCR as suggested by the SHANSEP equation, but consistently decreases with increasing consolidation effective stress. There is notable reduction in the stiffness ratio (Eu/[Formula: see text]) with stress level, and significant decrease in the large-strain friction angle.

scholarly journals Triaxial Testing of Geosynthetics Reinforced Tailings with Different Reinforced Layers

Materials ◽  
2020 ◽  
Vol 13 (8) ◽  
pp. 1943
Author(s):  
Fu Yi ◽  
Changbo Du
Keyword(s):  
Triaxial Compression ◽  
Friction Angle ◽  
Confining Pressure ◽  
Test Results ◽  
Compression Tests ◽  
Strength Index ◽  
Stress Strain ◽  
High Confining Pressure ◽  
Zhang Model ◽  
Triaxial Compression Tests

To evaluate the shear properties of geotextile-reinforced tailings, triaxial compression tests were performed on geogrids and geotextiles with zero, one, two, and four reinforced layers. The stress–strain characteristics and reinforcement effects of the reinforced tailings with different layers were analyzed. According to the test results, the geogrid stress–strain curves show hardening characteristics, whereas the geotextile stress–strain curves have strain-softening properties. With more reinforced layers, the hardening or softening characteristics become more prominent. We demonstrate that the stress–strain curves of geogrids and geotextile reinforced tailings under different reinforced layers can be fitted by the Duncan–Zhang model, which indicates that the pseudo-cohesion of shear strength index increases linearly whereas the friction angle remains primarily unchanged with the increase in reinforced layers. In addition, we observed that, although the strength of the reinforced tailings increases substantially, the reinforcement effect is more significant at a low confining pressure than at a high confining pressure. On the contrary, the triaxial specimen strength decreases with the increase in the number of reinforced layers. Our findings can provide valuable input toward the design and application of reinforced engineering.

scholarly journals Relation between the Friction Angle of Sand at Triaxial Compression and Triaxial Extension and Plane Strain Conditions

Geosciences ◽  
2020 ◽  
Vol 10 (1) ◽  
pp. 29 ◽  
Author(s):  
Zenon Szypcio
Keyword(s):  
Plane Strain ◽  
Soil Mechanics ◽  
Triaxial Compression ◽  
Deformation Mode ◽  
Friction Angle ◽  
Failure Criteria ◽  
Compression Tests ◽  
Laboratory Test Results ◽  
Experimental Findings ◽  
Triaxial Extension

The strength of sand is usually characterized by the maximum value of the secant friction angle. The friction angle is a function of deformation mode, density, and stress level and is strongly correlated with dilatancy at failure. Most often, the friction angle is evaluated from results of conventional compression tests, and correlation between the friction angle of sand at triaxial compression and triaxial extension and plane strain conditions is a vital problem of soil mechanics. These correlations can be obtained from laboratory test results. The failure criteria for sand presented in literature also give the possibility of finding correlations between friction angles for different deformation modes. The general stress-dilatancy relationship obtained from the frictional state concept, with some additional assumptions, gives the possibility of finding theoretical relationships between the friction angle of sand at triaxial compression and triaxial extension and plane strain conditions. The theoretically obtained relationships presented in the paper are fully consistent with theoretical and experimental findings of soil mechanics.

Influence of Water Contents on Shear Strength of Rammed Earth Wall of Earth-Building

2011 ◽  
Vol 382 ◽  
pp. 172-175
Author(s):  
Ren Wei Wu ◽  
Xing Qian Peng ◽  
Li Zhang
Keyword(s):  
Shear Strength ◽  
Water Content ◽  
Triaxial Compression ◽  
Friction Angle ◽  
World Heritage Site ◽  
Rammed Earth ◽  
Compression Tests ◽  
Rammed Earth Wall ◽  
Influence Of Water ◽  
Water Contents

As the "Fujian earth-building" have been inscribed by UNESCO in 2008 as World Heritage Site, attentions of protection about the "Fujian earth-building" has getting more and more. This article takes samples of a rammed-earth wall from Yongding earth-buildings and determines the shear strength of the samples with different water content through triaxial compression tests. The influence on shear strength of water content of rammed-earth samples is analyzed. Test results show that the shear strength of rammed-earth has much to do with the water content of the soil, the greater the water content is，the smaller the shear strength is. With water content increasing, cohesion and internal friction angle of rammed-earth were decreases, and its changing trend is of marked characteristic of stage. When water contents of rammed-earth is under some value, its cohesion changes in small ranges; when water contents of rammed-earth is over the value, its cohesion decreases with water content increasing.

scholarly journals Mechanical Properties of Grouted Crushed Coal with Different Grain Size Mixtures under Triaxial Compression

2018 ◽  
Vol 2018 ◽  
pp. 1-13 ◽  
Author(s):  
Yuhao Jin ◽  
Lijun Han ◽  
Qingbin Meng ◽  
Suresh Sanda ◽  
Haizhi Zang ◽  
...  
Keyword(s):  
Grain Size ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Peak Strain ◽  
Compression Tests ◽  
Reinforcement Effect ◽  
Confining Pressures ◽  
Mechanical Behaviours ◽  
Ultimate Failure ◽  
Different Grain Size

To have a better understanding of the reinforcement effect on the crushed zone after grouting in coal mining extraction work, a self-designed grouting apparatus was used to study the effects of the grain size mixtures (distribution) and the stress state on the mechanical behaviours of grouted crushed coal specimens. From the various grouting tests, triaxial compression tests and scanning electron microscopy (SEM) observations of grouted specimens with different grain size mixtures, it was found that, for the same grain size mixture, the peak (σp) and residual (σr) strengths of the grouted specimens increased with an increase in confining pressure. It was found that the average slope values of the σp-σ3 curves for the grouted specimens with different grain size mixtures were all larger than those of the σr-σ3 curves. It was observed that the peak strain (εp) of the grouted specimens with different grain size mixtures increased overall with increasing confining pressure. For constant confining pressure, the peak and residual strengths both gradually increased approximately linearly as the grain size mixtures varied from small to large, but at higher confining pressures, the influence of the grain size mixture on the peak (or residual) strength increased. These mechanical behaviours of the grouted crushed coal specimens were strongly dependent on the variation in the grain size mixtures and in the confining pressure, which can be explained by the crack evolution process within the grouted specimen under triaxial compression, to a certain extent. Ultimate failure of the grouted specimen occurred just after propagation and coalescence of the cracks through the entire grouted specimen. Moreover, there were three major microscopic diffusion modes for the grouts flowing in most of the crushed coal specimens. Based on these test results, it was found that the reinforcement effect of the grouted specimen related to the splitting grouting mode (occurring in most of the large specimens) seems to be better than that of the penetrating (filling) grouting mode (in most of the small specimens).

scholarly journals Experimental Investigation on Failure Modes and Mechanical Properties of Rock-Like Specimens with a Grout-Infilled Flaw under Triaxial Compression

2019 ◽  
Vol 2019 ◽  
pp. 1-14
Author(s):  
Huilin Le ◽  
Shaorui Sun ◽  
Feng Zhu ◽  
Haotian Fan
Keyword(s):  
Mechanical Properties ◽  
Rock Mass ◽  
Epoxy Resin ◽  
Failure Modes ◽  
Shear Failure ◽  
Fractured Rock ◽  
Triaxial Compression ◽  
Friction Angle ◽  
Confining Pressure ◽  
Compression Tests

Flaws existing in rock mass are one of the main factors resulting in the instability of rock mass. Epoxy resin is often used to reinforce fractured rock mass. However, few researches focused on mechanical properties of the specimens with a resin-infilled flaw under triaxial compression. Therefore, in this research, epoxy resin was selected as the grouting material, and triaxial compression tests were conducted on the rock-like specimens with a grout-infilled flaw having different geometries. This study draws some new conclusions. The high confining pressure suppresses the generation of tensile cracks, and the failure mode changes from tensile-shear failure to shear failure as the confining pressure increases. Grouting with epoxy resin leads to the improvement of peak strengths of the specimens under triaxial compression. The reinforcement effect of epoxy resin is better for the specimens having a large flaw length and those under a relatively low confining pressure. Grouting with epoxy resin reduces the internal friction angle of the samples but improves their cohesion. This research may provide some useful insights for understanding the mechanical behaviors of grouted rock masses.

Comparison of the Dynamic Properties and Undrained Shear Strengths of Offshore Calcareous Sand and Artificially Cemented Sand

2003 ◽  
Author(s):  
Celestino Valle ◽  
Beatriz I. Camacho ◽  
Kenneth H. Stokoe ◽  
Alan F. Rauch
Keyword(s):  
Sodium Silicate ◽  
Dynamic Properties ◽  
Triaxial Compression ◽  
Calcareous Soils ◽  
Sodium Silicate Solution ◽  
Small Strain ◽  
Compression Tests ◽  
Calcareous Sand ◽  
Cemented Sand ◽  
Undrained Shear

Calcareous sand specimens were obtained from Campeche Bay in the southern Gulf of Mexico. The dynamic properties of these specimens were measured in resonant column and torsional shear (RCTS) tests, while the undrained shear strength was measured in unconsolidated-undrained (UU) triaxial compression tests. For weakly cemented, natural materials like this, it is difficult to obtain reliable properties from laboratory tests because sampling and handling of the soil specimens damages the particle cementation to an unknown degree. Artificially cemented specimens can be studied to better understand this problem. In this work, the strength and dynamic properties of artificially cemented sand were also measured using RCTS and UU tests. The artificially cemented specimens were formed by mixing uniform sand with a sodium silicate solution. The degree of cementation was varied by using different sodium silicate concentrations. This approach could be used to reproduce cemented test specimens in the laboratory with similar mechanical properties as cemented offshore soils. The results from this limited study show that the small-strain dynamic properties measured in the laboratory, and their variation with confining pressure, clearly identifies disturbance in the calcareous soils.

Isothermal modeling of sand–bentonite mixtures at elevated temperatures

1995 ◽  
Vol 32 (1) ◽  
pp. 78-88 ◽  
Author(s):  
B.E. Lingnau ◽  
J. Graham ◽  
N. Tanaka
Keyword(s):  
Shear Strength ◽  
Elevated Temperatures ◽  
Triaxial Compression ◽  
Friction Angle ◽  
Compression Tests ◽  
Strain Behavior ◽  
Bentonite Buffer ◽  
State Boundary ◽  
Increasing Temperature ◽  
Triaxial Compression Tests

Two models are proposed for describing the stress–strain behavior of sand–bentonite (buffer) mixtures at elevated temperatures: (1) isothermal pseudoelasticity and (2) isothermal elastic-plasticity. Data to support the models come from consolidated undrained triaxial compression tests performed on dense saturated buffer specimens at effective confining stresses up to 9.0 MPa and temperatures of 26°, 65°, and 100 °C. Measurements indicate that volumes decrease with increasing temperature if the tests are carried out under drained conditions. These trends can be modelled by a family of hardening lines in semilog compression space. Power law relationships are presented for undrained shear-strength envelopes that increase in size with an increase in temperature. The slopes of unload-reload lines, κ, in semilog compression space vary with temperature and can be related to systematic variation in the friction angle [Formula: see text]. The shear modulus G50 at 50% peak strength also depends on temperature. Several plotting techniques are used to show the existence of different state boundary surfaces for each test temperature. Key words : sand–bentonite, buffer, compression, shear strength, temperature, modelling.

scholarly journals Numerical Triaxial Apparatus and Application

2013 ◽  
Vol 353-356 ◽  
pp. 3251-3255 ◽  
Author(s):  
Xiao Liang Wang ◽  
Jia Chun Li
Keyword(s):  
Granular Materials ◽  
Axial Strain ◽  
Triaxial Compression ◽  
Friction Angle ◽  
Good Prediction ◽  
Strain Response ◽  
Compression Tests ◽  
Dilatancy Angle ◽  
Triaxial Apparatus ◽  
Dem Model

A numerical triaxial apparatus based on discrete element method is developed on the platform of Yade using Python script. A DEM model with rolling resistance contact considered is proposed for dense granular materials, which is then applied in triaxial compression test of Chende sand. Stress-strain response and volume-axial strain response of the DEM model agree well with that of experiments, with a good prediction of dilatancy angle. Degradation of granular materials duo to particle erosion is also investigated using triaxial compression tests. It is indicated that peak friction angle decreases with the remove of particles if strong force network of granular materials is destroyed.

scholarly journals Effect of Cyclic Loading on the Lateral Behavior of Offshore Monopiles Using the Strain Wedge Model

2015 ◽  
Vol 2015 ◽  
pp. 1-12 ◽  
Author(s):  
Keunju Kim ◽  
Boo Hyun Nam ◽  
Heejung Youn
Keyword(s):  
Cyclic Loading ◽  
Lateral Displacement ◽  
Triaxial Compression ◽  
Lateral Loads ◽  
Compression Tests ◽  
Initial Stiffness ◽  
Quartz Sands ◽  
Number Of Cycles ◽  
Lateral Behavior ◽  
Strain Wedge

This paper presents the effect of cyclic loading on the lateral behavior of monopiles in terms of load-displacement curves, deflection curves, andp-ycurves along the pile. A commercial software, Strain Wedge Model (SWM), was employed, simulating a 7.5 m in diameter and 60 m long steel monopile embedded into quartz sands. In order to account for the effect of cyclic loading, accumulated strains were calculated based on the results of drained cyclic triaxial compression tests, and the accumulated strains were combined with static strains representing input strains into the SWM. The input strains were estimated for different numbers of cycles ranging from 1 to 105and 3 different cyclic lateral loads (25%, 50%, and 75% of static capacity). The lateral displacement at pile head was found to increase with increasing number of cycles and increasing cyclic lateral loads. In order to model these deformations resulting from cyclic loading, the initial stiffness of thep-ycurves has to be significantly reduced.

Sign in / Sign up

Export Citation Format

Share Document