scholarly journals Gas Expansion Energy Model and Numerical Simulation of Outburst Coal Seam under Multifield Coupling

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-10
Author(s):  
Jie Cao ◽  
Qianting Hu ◽  
Yanan Gao ◽  
Minghui Li ◽  
Dongling Sun
Keyword(s):  
Diffusion Coefficient ◽  
Coal Seam ◽  
Volumetric Strain ◽  
Gas Pressure ◽  
Coal Seams ◽  
Distribution Law ◽  
Free Gas ◽  
Working Face ◽  
Expansion Energy ◽  
Gas Expansion

Due to the insufficient understanding of the outburst mechanism, the coal and gas outburst disasters in China are more serious. Gas expansion energy is the main source of energy that causes outburst. In order to explore the distribution law of gas expansion energy in outburst coal seams, a gas-solid coupling equation of outburst coal seams was established. The distribution law of coal stress field, deformation field, gas flow field, and gas expansion energy were simulated and analyzed by using COMSOL Multiphysics. The results showed that from the excavation face to the deep part of coal seam, the stress presented unloading zone, stress concentration zone, and original stress zone. The volumetric strain and permeability reached the minimum, while the gas pressure reached the maximum at the peak value of vertical stress. As time goes on, the gas pressure in the fracture near the working face gradually decreased and was less than the pressure in coal matrix. The total gas expansion energy consists of free gas and desorption gas expansion energy. Affected by the excavation, free gas expansion energy maintained a constant value in the original coal seam and gradually decreased in the area close to the working face. The expansion energy provided by desorption gas was zero in the original coal seam. And it first increased and then decreased rapidly near the working face. Compared with stress and coal seam thickness, gas pressure and initial diffusion coefficient had significant influence on gas expansion energy of coal seam. When the diffusion coefficient was greater than 1e-9 m2/s, the gas expansion energy of the coal seam near the working face was significantly higher than that of the original coal seam, which had the risk of inducing outburst.

Characters Evaluation of Ground Pressure in Fully Mechanized Top Coal Caving Face in Soft Coal Seams

2011 ◽  
Vol 255-260 ◽  
pp. 3735-3739
Author(s):  
Wei Dong Pan ◽  
Xiao Hua Wu ◽  
Yang Li
Keyword(s):  
Coal Seam ◽  
Mining Area ◽  
Base Point ◽  
Coal Seams ◽  
Distribution Law ◽  
Soft Coal ◽  
Ground Pressure ◽  
Working Face ◽  
Working Resistance ◽  
Hydraulic Supports

Based on the big thickness, low stiffiness and other characters of No. 8 coal seam in Huaibei mining area, the moving laws of top coal seam and roof, and distribution law of ground pressure were studied under the fully mechanized top coal caving. The research methods included working resistance observation of hydraulic supports in working face, deformation observation of stope roadways and deeper base point observation in roof and top coal. The results show that, in the thick and soft coal seams, the influence coverage of mining ground pressure in fully mechanized top coal caving face is much wider than that in the working face with general mining technology, but the intensity of pressure is much lower.

scholarly journals Comprehensive technical support for safe mining in ultra-close coal seams: A case study

2021 ◽  
pp. 014459872110093
Author(s):  
Wei Zhang ◽  
Jiawei Guo ◽  
Kaidi Xie ◽  
Jinming Wang ◽  
Liang Chen ◽  
...  
Keyword(s):  
Coal Seam ◽  
Technical Support ◽  
Surrounding Rock ◽  
Coal Seams ◽  
Deformation Control ◽  
Hard Roof ◽  
Working Face ◽  
Close Coal Seams ◽  
Safe Mining

In order to mine the coal seam under super-thick hard roof, improve the utilization rate of resources and prolong the remaining service life of the mine, a case study of the Gaozhuang Coal Mine in the Zaozhuang Mining Area has been performed in this paper. Based on the specific mining geological conditions of ultra-close coal seams (#3up and #3low coal seams), their joint systematic analysis has been performed, with the focus made in the following three aspects: (i) prevention of rock burst under super-thick hard roof, (ii) deformation control of surrounding rock of roadways in the lower coal seam, and (iii) fire prevention in the goaf of working face. Given the strong bursting tendency observed in upper coal seam and lower coal seam, the technology of preventing rock burst under super-thick hard roof was proposed, which involved setting of narrow section coal pillars to protect roadways and interleaving layout of working faces. The specific supporting scheme of surrounding rock of roadways in the #3low1101 working face was determined, and the grouting reinforcement method of local fractured zones through Marithan was further proposed, to ensure the deformation control of surrounding rock of roadways in lower coal seams. The proposed fire prevention technology envisaged goaf grouting and spraying to plug leaks, which reduced the hazard of spontaneous combustion of residual coals in mined ultra-close coal seams. The technical and economic improvements with a direct economic benefit of 5.55 million yuan were achieved by the application of the proposed comprehensive technical support. The research results obtained provide a theoretical guidance and technical support of safe mining strategies of close coal seams in other mining areas.

scholarly journals Surrounding Rock Movement of Steeply Dipping Coal Seam Using Backfill Mining

2021 ◽  
Vol 2021 ◽  
pp. 1-17
Author(s):  
Wenyu Lv ◽  
Kai Guo ◽  
Jianhao Yu ◽  
Xufeng Du ◽  
Kun Feng
Keyword(s):  
Numerical Simulation ◽  
Coal Seam ◽  
Surrounding Rock ◽  
Maximum Deflection ◽  
Coal Seams ◽  
Physical Similarity ◽  
Working Face ◽  
Rock Structure ◽  
Backfill Mining ◽  
The Stability

The movement of the overlying strata in steeply dipping coal seams is complex, and the deformation of roof rock beam is obvious. In general, the backfill mining method can improve the stability of the surrounding rock effectively. In this study, the 645 working face of the tested mine is used as a prototype to establish the mechanical model of the inclined roof beam using the sloping flexible shield support backfilling method in a steeply dipping coal seam, and the deflection equation is derived to obtain the roof damage structure and the maximum deflection position of the roof beam. Finally, numerical simulation and physical similarity simulation experiments are carried out to study the stability of the surrounding rock structure under backfilling mining in steeply dipping coal seams. The results show the following: (1) With the support of the gangue filling body, the inclined roof beam has smaller roof subsidence, and the maximum deflection position moves to the upper part of working face. (2) With the increase of the stope height, the stress and displacement field of the surrounding rock using the backfilling method show an asymmetrical distribution, the movement, deformation, and failure increase slowly, and the increase of the strain is relatively stable. Compared with the caving method, the range and degree of the surrounding rock disturbed by the mining stress are lower. The results of numerical simulation and physical similarity simulation experiment are generally consistent with the theoretically derived results. Overall, this study can provide theoretical basis for the safe and efficient production of steeply dipping coal seams.

Numerical Simulation of Underground Pressure in Mining High-Inclined Coal-Seam with Analysis of Material Properties in Mine Dongbaowei

2013 ◽  
Vol 644 ◽  
pp. 382-386 ◽  
Author(s):  
Ming Ming Wen
Keyword(s):  
Coal Seam ◽  
In Situ Observation ◽  
Coal Seams ◽  
Relevant Model ◽  
Roof Caving ◽  
Deformation Feature ◽  
Working Face ◽  
Strata Behavior ◽  
Surrounding Rock Stress

The FLAC software is used in establishing a relevant model to study the strata behavior of fully mechanized working face of steep coal seams. Using this model, we have simulated the roof caving characteristic and the stress distribution of surrounding rocks and analyzed the deformation feature of the surrounding rocks in the working face end. Based on the in-situ observation about the fully mechanized working face, we have obtained the surrounding rock stress and the strata behavior of steep coal seam and proposed some countermeasures aiming at these problems.

scholarly journals Study on Stress Distribution Law of High-Efficiency Paste Backfilling Working Face with Solid Waste in Thick Coal Seam

2020 ◽  
Vol 2020 ◽  
pp. 1-13
Author(s):  
Meng Zhang ◽  
Dan Fang
Keyword(s):  
Sustainable Development ◽  
Stress Distribution ◽  
Coal Seam ◽  
Solid Waste ◽  
Research Methods ◽  
High Efficiency ◽  
Distribution Law ◽  
Thick Coal Seam ◽  
The Sustainable Development ◽  
Working Face

The high-efficiency paste backfilling mining technology of solid waste in thick coal seam above 6 m is a complex system engineering, which involves mining, backfilling, supporting, subsidence, safety, and other aspects, so it is of great strategic significance to study the technology. In this paper, on the basis of comprehensive research methods such as laboratory experiments, theoretical analysis, computer programming, and other comprehensive research methods, aiming at the problems of low production capacity and high paste backfilling cost, taking the mining of No. 3 Coal Seam under buildings in Lu’an area as the research object, the stress distribution law of high-efficiency paste backfilling working face with solid waste in more than 6-meter-thick coal seam was carried out. The main achievements are as follows: On the basis of the theoretical establishment of the program method for the instability discriminant analysis of roof rock beam failure with the change of backfilling body unit strength with time, a numerical calculation model considering the change process of backfilling body strength is established. The stress distribution analysis of the E1302 working face before and during the mining process plays a guiding role in the actual production of the whole working face and roadway. The research results support the sustainable development of coal mining enterprises from technology, which has great economic, social, and environmental benefits, and can promote the industrialization of green mining high-tech in Shanxi Province and even the whole country and can promote the green mining technology progress of paste backfilling in coal mines in China, which is of great significance to the sustainable development of mining production and environmental construction.

scholarly journals Stability of "Support-Surrounding Rock" System for Fully Mechanized Longwall Mining in Steeply Dipping Coal Seams

2021 ◽  
Author(s):  
Luo Shenghu ◽  
tong wang ◽  
Wu Yongping ◽  
Huangfu Jingyu ◽  
Zhao Huatao
Keyword(s):  
Coal Seam ◽  
Longwall Mining ◽  
Stability Control ◽  
Surrounding Rock ◽  
Coal Seams ◽  
Physical Test ◽  
Rock System ◽  
Working Face ◽  
The Stability ◽  
Mining Height

Abstract The key to the safe and efficient longwall mining of steeply dipping seams lies in the stability control of the "support-surrounding rock" system. This paper analyzes the difficulty of controlling the stability of the support during the longwall mining process of steeply dipping coal seams in terms of the characteristics of the non-uniform filled-in gob using a combination of physical test, theoretical analysis and field measurements. Considering the floor as an elastic foundation, we built a "support-surrounding rock" mechanical model based on data obtained on "support-surrounding rock" systems in different regions and the laws of support motion under different load conditions. Our findings are summarized as follows. First, depending on the angle of the coal seam, the caving gangue will roll (slide) downward along the incline, resulting in the formation of a non-uniform filling zone in the deep gob in which the lower, middle, and upper sections are filled, half-filled, and empty, respectively. In addition, an inverted triangular hollow surface is formed on the floor of the gob in the middle and upper sections behind the support. Furthermore, as the angle of the coal seam, length of the working face, and mining height increase, the characteristics of the non-uniform filled-in gob are enhanced. Second, we found that, as a result of support by the gangue, the "support-surrounding rock" system is relatively stable in the lower part of the working face while, in the middle and upper sections of the working face, the contact method and loading characteristics of the support are more complicated, making stability control difficult. Third, the magnitude and direction of the load, action point, and mining height all affect the stability of the support to varying degrees, with the tangential load and action position of the roof load having the most significant impacts on the stability of the support. Under loading by the roof, rotation and subsidence of the support inevitably occur, with gradually increasing amplitude and effects on the inter-support and sliding forces. Finally, we found that it is advisable in the process of moving the support to adopt "sliding advance of support" measures and to apply a "down-up" removal order to ensure overall stability. These research results provide reference and guidance of significance to field practice production.

scholarly journals Dynamic Characterization during Gas Initial Desorption of Coal Particles and Its Influence on the Initiation of Coal and Gas Outbursts

Processes ◽  
2021 ◽  
Vol 9 (7) ◽  
pp. 1101
Author(s):  
Chaojie Wang ◽  
Xiaowei Li ◽  
Changhang Xu ◽  
Yujia Chen ◽  
Zexiang Tang ◽  
...  
Keyword(s):  
Pressure Gradient ◽  
Dynamic Effect ◽  
Coal Mass ◽  
Gas Pressure ◽  
Coal Surface ◽  
Dynamic Characterization ◽  
Coal Particles ◽  
Expansion Energy ◽  
Gas Expansion ◽  
Two Peaks

The law of gas initial desorption from coals is greatly important for understanding the occurrence mechanism and predicting coal and gas outburst (hereinafter referred to as ‘outburst’). However, dynamic characterization of gas initial desorption remains to be investigated. In this study, by monitoring the gas pressure and temperature of tectonically deformed (TD) coal and primary-undeformed (PU) coal, we established the evolution laws of gas key parameters during the initial desorption. The results indicate that the gas pressure drop rate, mass flow rate, initial desorption rate, and gas velocity increase with increasing gas pressure, with stronger gas dynamic effect, generating a high pressure gradient on the coal surface. Under the same gas pressure, the pressure gradient formed on the TD coal surface is greater than that formed on the surface of the PU coal, resulting in easily initiating an outburst in the TD coal. Moreover, the increased gas pressure increases temperature change rates (falling rate and rising rate) of coal mass. The minimum and final stable temperatures in the TD coal are generally lower compared to the PU coal. The releasing process of gas expansion energy can be divided into two stages exhibiting two peaks which increase as gas pressure increases. The two peak values for the TD coal both are about 2–3 times of those of the PU coal. In addition, the total gas expansion energy released by TD coal is far greater than that released by PU coal. The two peaks and the total values of gas expansion energy also prove that the damage of gas pressure to coal mass increases with the increased pressure, more likely producing pulverized coals and more prone to initiate an outburst.

Recent Patents on Thin Coal Seam Mining Equipment

2020 ◽  
Vol 13 (2) ◽  
pp. 99-108
Author(s):  
Yanxiang Wang ◽  
Daolong Yang ◽  
Bangsheng Xing ◽  
Tingting Zhao ◽  
Zhiyi Sun ◽  
...  
Keyword(s):  
Coal Seam ◽  
Underground Space ◽  
Mining Method ◽  
Mining Equipment ◽  
Coal Seams ◽  
Thin Coal Seam ◽  
Recoverable Reserves ◽  
Working Face ◽  
Geological Conditions ◽  
Seam Mining

Background:: China's thin and extremely thin coal seam resources are widely distributed and rich in reserves. These coal seams account for 20% of the recoverable reserves, with 9.83 billion tons of industrial reserves and 6.15 billion tons of recoverable reserves. Objective: Due to the complex geological conditions of the thin coal seam, the plow mining method cannot be effectively popularized, and the drum mining method is difficult to be popularized and applied in small and medium-sized coal mines, so it is necessary to find other more advantageous alternative mining methods. Methods: The equipment integrates mining operations, conveying operations, and supporting operations, and is suitable for mining short and extremely thin coal seam with a height of 0.35m-0.8m and width of 2m-20m. It has the advantages of the low body of the shearer, no additional support on the working face, and small underground space. The mining efficiency of thin coal seam and very thin coal seam can be improved and the mining cost can be reduced. Results: Thin coal seam shear mining combines mining, conveying, and supporting processes together and has the advantages of a low fuselage, no extra support required for the working face, and feasibility in a small underground space. Conclusion: The summarized mining method can improve the mining efficiency of thin and extremely thin coal seams, reduce mining costs, and incorporate green mining practices, which take both mining economy and safety into account.

scholarly journals A New Method for the Measurement of Gas Pressure in Water-Bearing Coal Seams and Its Application

Geofluids ◽  
2020 ◽  
Vol 2020 ◽  
pp. 1-11
Author(s):  
Xiao Cui ◽  
Jiayong Zhang ◽  
Liwen Guo ◽  
Xuemin Gong
Keyword(s):  
Coal Seam ◽  
Field Experiments ◽  
Water Pressure ◽  
Direct Methods ◽  
Gas Pressure ◽  
New Method ◽  
Well Testing ◽  
Coal Seams ◽  
Coal Seam Gas ◽  
Gas Disaster

Coal seam gas pressure is one of the fundamental parameters used to assess coal seam gas occurrence and is an important index in assessing the risk of gas disaster. However, the geological characteristics of coal seams become increasingly complex with increasing mining degree, thus decreasing the accuracy and success rate of direct methods for measuring gas pressure. To address such issues, we have developed a new method for direct measurement of gas pressure in water-bearing coal seams. In particular, we developed a pressure measurement device based on theoretical analysis and quantified the basic parameters of the device based on well testing. Then, we verified the applicability of our method based on comparative analysis of the results of field experiments and indirect measurements. Our results demonstrate that this new method can resolve the effects of water pressure, coal slime, and other factors on the estimation of gas pressure. The performance of this new method is considerably better than that of traditional methods. In particular, field test results demonstrate that our method can accurately and efficiently measure gas pressure in water-bearing coal seams. These results will be of great significance in the prevention and control of coal seam gas disaster.

scholarly journals Experimental Investigation on the Release Rule of the Gas Expansion Potential of Loaded Water-Filled Soft Coal

2019 ◽  
Vol 2019 ◽  
pp. 1-9
Author(s):  
Hengjie Qin ◽  
Jianping Wei ◽  
Donghao Li ◽  
Sen Li
Keyword(s):  
Water Content ◽  
Minimum Energy ◽  
Gas Pressure ◽  
Coal And Gas Outburst ◽  
Energy Evolution ◽  
Experimental Conditions ◽  
Gas Outburst ◽  
Minimum Energy Consumption ◽  
Expansion Energy ◽  
Gas Expansion

The aim of this study was to explore the evolution and release rule of internal energy storage in the process of coal and gas outburst and to further reveal the mechanism of coal and gas outburst from the perspective of energy. In this paper, the experiment of gas expansion energy release of coal samples under different adsorption pressures and with different moisture contents was carried out with the self-developed experimental device for release of gas-bearing coal expansion energy under load, and the energy of the whole outburst process was divided into three parts: the total expansion energy of gas, the energy consumed by destroying and throwing out coal body and the energy released inefficiently. On the basis of reasonable assumption, the energy evolution calculation model of each part was constructed with mathematical method. By analyzing the changes and distribution rules of three parts of energy under different experimental conditions, this paper explored the controlling effects of gas pressure, water content, and other variables on the energy evolution rules in the process of coal and gas outburst. Experimental and theoretical studies showed that in the gas-dominated coal and gas outburst process, the destruction of coal body was in the form of stratification; under each experimental condition, there existed a critical gas pressure value for the occurrence of coal and gas outburst, and there was a sudden change of energy evolution near this value; the existence of water made the critical pressure and the minimum energy consumption of coal and gas outburst increase obviously; under the experimental conditions, there was a linear relationship between the critical gas pressure and water content and a positive exponential relationship between the minimum energy consumption and water content.

Sign in / Sign up

Export Citation Format

Share Document