scholarly journals Application of Raw and Modified Pomegranate Peel for Wastewater Treatment: A Literature Overview and Analysis

2021 ◽  
Vol 2021 ◽  
pp. 1-19
Author(s):  
Samia Ben-Ali
Keyword(s):  
Wastewater Treatment ◽  
Low Cost ◽  
Adsorption Properties ◽  
Isotherm Models ◽  
Pomegranate Peel ◽  
Practical Applications ◽  
Literature Overview ◽  
Chemical Conditions ◽  
Physical And Chemical ◽  
Adsorbent Dose

The use of renewable substrates as biosorbents has a great attention in wastewater treatment. The pomegranate peel (PGP) constitutes one of these substrates. A review is carried out to investigate the potential of pomegranate peel (PGP) for wastewater treatment. Physical and chemical PGP properties are presented and compared to those of Tunisian pomegranate peel (El Gabsi). Raw and modified PGP performance and sorption capacity for metals, dyes, and organic pollutants are evaluated. Different experimental sorption conditions such as concentration, contact time, pH, temperature, and adsorbent dose used in the literature are illustrated. Studied and best-fitted kinetics and isotherm models to experimental data and thermodynamic parameters are compared. The effects of activating physical and/or chemical conditions on the activated PGP properties are presented. This paper reveals noteworthiness properties of raw PGP for wastewater treatment compared to this activated form. The comparison between activated and raw PGP morphology exhibits that the activation does not necessarily improve the PGP adsorption capacity. Despite a limited research carried out on the raw PGP biosorbent, it appears from this study that it has very good adsorption properties, making it a serious and low-cost renewable substrate toward practical applications in wastewater treatment compared to various other waste agricultural biomass.

scholarly journals Cadmium Removal by using Pumice Modified with Iron Nanoparticles from Aqueous Solutions

2016 ◽  
Vol 18 (2) ◽  
pp. 426-436 ◽  
Keyword(s):  
Contact Time ◽  
Iron Nanoparticles ◽  
Cadmium Concentration ◽  
Synthetic Wastewater ◽  
Isotherm Models ◽  
Cadmium Removal ◽  
Pumice Stone ◽  
Practical Applications ◽  
Equilibrium Data ◽  
Adsorbent Dose

<p>In this study, the removal of cadmium by using pumice coated with iron nanoparticles (INPs) from synthetic wastewater was investigated. The effects of parameters influencing adsorption: contact time (10-20 min), pH (3-9), initial cadmium concentration (25-125 mg l<sup>-1</sup>) and adsorbent dose (2-10 g l<sup>-1</sup>) were studied. The pumice stone used in this research was, first, crashed and then sieved with 20 mesh standard sieves (0.85 mm); finally, it was coated with INPs. An atomic absorption spectrophotometer was used to measure cadmium contents and isotherm models and adsorption kinetics were studied. The results showed the adsorption process of cadmium reached equilibrium at contact time of 80 min. With increasing pH solution, the efficiency enhanced which peaked at pH 7-8. Cadmium concentration increase resulted in a decrease in efficiency, whereas adsorbent dose increase improved it. Equilibrium data of adsorption followed isotherms models: Langmuir and Freundlich. The highest removal efficiency and adsorption capacity were, respectively, 83% and 17.27 mg g<sup>-1</sup>. Furthermore, absorption kinetics is better described by the pseudo second-order model. According to the results obtained, pumice coated with INPs is an effective adsorbent and can be introduced as a suitable option in practical applications</p>

scholarly journals A solid-state chemical method for synthesizing MgO nanoparticles with superior adsorption properties

RSC Advances ◽  
2019 ◽  
Vol 9 (4) ◽  
pp. 2011-2017 ◽  
Author(s):  
Hongyu Zhang ◽  
Jindou Hu ◽  
Jing Xie ◽  
Shiqiang Wang ◽  
Yali Cao
Keyword(s):  
Wastewater Treatment ◽  
Solid State ◽  
Chemical Method ◽  
Low Cost ◽  
Adsorption Properties ◽  
Mgo Nanoparticles ◽  
State Chemical

As a traditional and effective adsorbent, MgO is a low-cost, eco-friendly, nontoxic, and economical material for wastewater treatment.

scholarly journals Hospitals and Laboratories on Paper-Based Sensors: A Mini Review

Sensors ◽  
2021 ◽  
Vol 21 (18) ◽  
pp. 5998
Author(s):  
Huaizu Zhang ◽  
Chengbin Xia ◽  
Guangfu Feng ◽  
Jun Fang
Keyword(s):  
Low Cost ◽  
High Accuracy ◽  
Trace Detection ◽  
Laboratory Equipment ◽  
Optical Signals ◽  
Practical Applications ◽  
Number Of Factors ◽  
Acid Protein ◽  
Inorganic Chemical ◽  
Physical And Chemical

With characters of low cost, portability, easy disposal, and high accuracy, as well as bulky reduced laboratory equipment, paper-based sensors are getting increasing attention for reliable indoor/outdoor onsite detection with nonexpert operation. They have become powerful analysis tools in trace detection with ultra-low detection limits and extremely high accuracy, resulting in their great popularity in medical detection, environmental inspection, and other applications. Herein, we summarize and generalize the recently reported paper-based sensors based on their application for mechanics, biomolecules, food safety, and environmental inspection. Based on the biological, physical, and chemical analytes-sensitive electrical or optical signals, extensive detections of a large number of factors such as humidity, pressure, nucleic acid, protein, sugar, biomarkers, metal ions, and organic/inorganic chemical substances have been reported via paper-based sensors. Challenges faced by the current paper-based sensors from the fundamental problems and practical applications are subsequently analyzed; thus, the future directions of paper-based sensors are specified for their rapid handheld testing.

scholarly journals A Review on Microbial Electrocatalysis Systems Coupled with Membrane Bioreactor to Improve Wastewater Treatment

2019 ◽  
Vol 7 (10) ◽  
pp. 372 ◽  
Author(s):  
Wang ◽  
Zhao ◽  
Kakade ◽  
Kulshreshtha ◽  
Liu ◽  
...  
Keyword(s):  
Wastewater Treatment ◽  
Membrane Fouling ◽  
Microbial Fuel Cells ◽  
High Efficiency ◽  
Low Cost ◽  
Electric Energy ◽  
Processing Efficiency ◽  
Additional Energy ◽  
Practical Applications ◽  
Microbial Electrocatalysis

Microbial electrocatalysis is an electro reaction that uses microorganisms as a biocatalyst, mainly including microbial electrolytic cells (MEC) and microbial fuel cells (MFC), which has been used for wastewater treatment. However, the low processing efficiency is the main drawback for its practical application and the additional energy input of MEC system results in high costs. Recently, MFC/MEC coupled with other treatment processes, especially membrane bioreactors (MBR), has been used for high efficiency and low-cost wastewater treatment. In these systems, the wastewater treatment efficiency can be improved after two units are operated and the membrane fouling of MBR can also be alleviated by the electric energy that was generated in the MFC. In addition, the power output of MFC can also reduce the energy consumption of microbial electrocatalysis systems. This review summarizes the recent studies about microbial electrocatalysis systems coupled with MBR, describing the combination types and microorganism distribution, the advantages and limitations of the systems, and also addresses several suggestions for the future development and practical applications.

scholarly journals A novel application of building demolition waste for removal benzene from aqueous solutions

2021 ◽  
Vol 30 (1) ◽  
pp. 86-97
Author(s):  
Saif Alquzweeni ◽  
Rasha Alkizwini ◽  
Afrah Hassan
Keyword(s):  
Aqueous Solutions ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
Isotherm Models ◽  
Batch Adsorption ◽  
Demolition Waste ◽  
Average Percentage ◽  
Benzene Removal ◽  
Building Demolition ◽  
Adsorbent Dose

A novel application of building demolition waste for removal benzene from aqueous solutions. In this research, demolition waste from buildings has been studied for possible use as benzene removal adsorbent from aquatic solution. The effect of adsorbent dosage, contact time, initial benzene concentration, and initial pH on benzene adsorption capacity have been investigated in the batch adsorption experiments. The adsorption effects initially happened very rapidly and achieved equilibrium within 180 min. Benzene removal was observed to decrease by an increase in the initial concentration of benzene of 300–700 mg·L–1, an increase in the adsorbent dose of 0.4–2.4 g per 100 mL, where an optimum adsorbent dose equal to 1.2 g per 100 mL was found. The potential of adsorption increases with pH 3.0–7.0 to reach the maximum removal efficiency at pH 6.0. The findings showed that equilibrium data were adequately adapted and correlated with the Freundlich isotherm models. The average percentage of the removal at room temperature was about 98%. Results suggest that building demolition waste can be used effectively in industrial wastewater treatment for the removal of aromatic hydrocarbon, benzene, as a low-cost option.

scholarly journals A review of biomass materials for advanced lithium–sulfur batteries

2019 ◽  
Vol 10 (32) ◽  
pp. 7484-7495 ◽  
Author(s):  
Huadong Yuan ◽  
Tiefeng Liu ◽  
Yujing Liu ◽  
Jianwei Nai ◽  
Yao Wang ◽  
...  
Keyword(s):  
Recent Progress ◽  
Low Cost ◽  
High Abundance ◽  
Chemical Adsorption ◽  
Environmental Friendliness ◽  
Lithium Sulfur Batteries ◽  
Biomass Materials ◽  
Physical And Chemical ◽  
Lithium Sulfur

This review summarizes recent progress of biomass-derived materials in Li–S batteries. These materials are promising due to their advantages including strong physical and chemical adsorption, high abundance, low cost, and environmental friendliness.

Permeability to albumin in isolated coronary venules

1993 ◽  
Vol 265 (2) ◽  
pp. H543-H552 ◽  
Author(s):  
Y. Yuan ◽  
W. M. Chilian ◽  
H. J. Granger ◽  
D. C. Zawieja
Keyword(s):  
Permeability Coefficient ◽  
Filtration Rate ◽  
Intraluminal Pressure ◽  
Apparent Permeability ◽  
Filtration Pressure ◽  
Diffusive Permeability ◽  
Apparent Permeability Coefficient ◽  
Chemical Conditions ◽  
Physical And Chemical ◽  
Intravascular Pressure

This study reports measurements of albumin permeability in isolated coronary venules. The isolated microvessel technique allows the quantification of transmural exchange of macromolecules under tightly controlled physical and chemical conditions. Transvenular exchange of albumin was studied in isolated coronary venules during alterations in filtration rate caused by changes in intravascular pressure. The apparent permeability coefficient of albumin (Pa) at an intraluminal pressure of 11 cmH2O was 3.92 +/- 0.43 x 10(-6) cm/s. Elevating intraluminal pressure to 16 and 21 cmH2O increased Pa to 5.13 +/- 0.57 x 10(-6) and 6.78 +/- 0.66 x 10(-6) cm/s, respectively. Calculation of the true diffusive permeability coefficient of albumin (Pd) at zero filtration rate was 1.54 x 10(-6) cm/s. The product of hydraulic conductance (Lp) and (1 - sigma), where sigma is the solute reflection coefficient, was 3.25 x 10(-7) cm.s-1 x cmH2O-1. At a net filtration pressure of 4-5 cmH2O, diffusion accounts for > 60% of total albumin transport across the venular wall. Transmural albumin flux is very sensitive to filtration rate, rising 6.7% for each cmH2O elevation of net filtration pressure. At 11 cmH2O net filtration pressure, convection accounts for nearly 70% of net albumin extravasation from the venular lumen. We suggest that the isolated coronary venule is a suitable preparation for the study of solute exchange in the heart.

scholarly journals Chemical Modification of Combusted Coal Gangue for U(VI) Adsorption: Towards a Waste Control by Waste Strategy

2021 ◽  
Vol 13 (15) ◽  
pp. 8421
Author(s):  
Yuan Gao ◽  
Jiandong Huang ◽  
Meng Li ◽  
Zhongran Dai ◽  
Rongli Jiang ◽  
...  
Keyword(s):  
Structural Analysis ◽  
High Efficiency ◽  
Low Cost ◽  
Chemical Activation ◽  
Cost Effective ◽  
Coal Gangue ◽  
Order Kinetic ◽  
Practical Applications ◽  
Detailed Structural Analysis ◽  
Alkaline Conditions

Uranium mining waste causes serious radiation-related health and environmental problems. This has encouraged efforts toward U(VI) removal with low cost and high efficiency. Typical uranium adsorbents, such as polymers, geopolymers, zeolites, and MOFs, and their associated high costs limit their practical applications. In this regard, this work found that the natural combusted coal gangue (CCG) could be a potential precursor of cheap sorbents to eliminate U(VI). The removal efficiency was modulated by chemical activation under acid and alkaline conditions, obtaining HCG (CCG activated with HCl) and KCG (CCG activated with KOH), respectively. The detailed structural analysis uncovered that those natural mineral substances, including quartz and kaolinite, were the main components in CCG and HCG. One of the key findings was that kalsilite formed in KCG under a mild synthetic condition can conspicuous enhance the affinity towards U(VI). The best equilibrium adsorption capacity with KCG was observed to be 140 mg/g under pH 6 within 120 min, following a pseudo-second-order kinetic model. To understand the improved adsorption performance, an adsorption mechanism was proposed by evaluating the pH of uranyl solutions, adsorbent dosage, as well as contact time. Combining with the structural analysis, this revealed that the uranyl adsorption process was mainly governed by chemisorption. This study gave rise to a utilization approach for CCG to obtain cost-effective adsorbents and paved a novel way towards eliminating uranium by a waste control by waste strategy.

scholarly journals Preparation and photocatalytic performance of metallic Nb0.9Ta0.1S2/2D-C3N4 composite

2020 ◽  
Vol 1 (1) ◽  
Author(s):  
Hanxiang Chen ◽  
Jianjian Yi ◽  
Zhao Mo ◽  
Yanhua Song ◽  
Wenshu Yang ◽  
...  
Keyword(s):  
Separation Efficiency ◽  
Low Cost ◽  
Metal Sulfide ◽  
Electron Hole ◽  
Practical Applications ◽  
Energy And Environment ◽  
Photocatalytic Application ◽  
Light Utilization ◽  
Ternary Metal ◽  
Key Issues

Abstract Photocatalysis technology has potential application in the field of energy and environment. How to expand visible light utilization and promote the separation efficiency of the carriers are the key issues for the high active photocatalysts preparation and future practical applications. In this work, a ternary metal sulfide Nb0.9Ta0.1S2 was prepared and used as an electron collector in the photocatalytic application. As a result, the generated electrons are quickly transferred to the surface of the composite to participate in the reaction. It was demonstrated that the photocatalytic activity of 2D-C3N4 was enhanced after the modification of Nb0.9Ta0.1S2. The Nb0.9Ta0.1S2/2D-C3N4 composite material was synthesized by solvothermal method. The composition of 5% Nb0.9Ta0.1S2/2D-C3N4 showed the highest H2 evolution rate of 1961.6 μmolg−1h−1, which was 6.6 times that of 2D-C3N4. The 15% Nb0.9Ta0.1S2/2D-C3N4 exhibited the best activity in Rhodamine B degradation rate of 97% in 2 h, which is 50% higher than that of 2D-C3N4. Nb0.9Ta0.1S2/2D-C3N4 can be used as electron trap to promote the effective separation of electron–hole pairs. This work provides benchmarks in exploring low-cost and efficient cocatalyst.

scholarly journals Ultrafiltration Process in Disinfection and Advanced Treatment of Tertiary Treated Wastewater

Membranes ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 221
Author(s):  
Rafał Tytus Bray ◽  
Katarzyna Jankowska ◽  
Eliza Kulbat ◽  
Aneta Łuczkiewicz ◽  
Aleksandra Sokołowska
Keyword(s):  
Wastewater Treatment ◽  
Wastewater Treatment Plants ◽  
Microscopic Analysis ◽  
Fecal Coliforms ◽  
Treated Wastewater ◽  
Chemical Parameters ◽  
Virus Particles ◽  
E Coli ◽  
The One ◽  
Physical And Chemical

The paper presents the results of research on the use of ultrafiltration, using membranes of 200 and 400 kDa separation, for disinfection of municipal treated wastewater. The research was conducted on a fractional technical scale using real municipal treated wastewater from two large wastewater treatment plants treating most of the wastewater over the one-million polycentric Gdańsk agglomeration (1.2 million inhabitants). UF 200 kDa and UF 400 kDa processes enabled further improvement of the physical and chemical parameters of treated wastewater. Total phosphorus (to below 0.2 mg/L–UF 200 kDa, 0.13 mg/L–UF 400 kDa) and turbid substances (to below 0.2 mg/L, both membranes) were removed in the highest degree. COD was reduced efficiently (to below 25.6 mgO2/L–UF 200 kDa, 26.8 mgO2/L–UF 400 kDa), while total nitrogen was removed to a small extent (to 7.12 mg/L–UF 200 kDa and 5.7 mg/L–UF 400 kDa. Based on the reduction of indicator bacteria; fecal coliforms including E. coli (FC) and fecal enterococci (FE) it was found that the ultrafiltration is an effective method of disinfection. Not much indicator bacterial were observed in the permeate after processes (UF 200 kDa; FC—5 CFU/L; FE—1 CFU/L and UF 400 kDa; FC—70 CFU/L; FE—10 CFU/L. However, microscopic analysis of prokaryotic cells and virus particles showed their presence after the application of both membrane types; TCN 3.0 × 102 cells/mL–UF 200 kDa, 5.0 × 103 cells/mL–UF 400 kDa, VP 1.0 × 105/mL. The presence of potentially pathogenic, highly infectious virus particles means that ultrafiltration cannot be considered a sufficient disinfection method for treated wastewater diverted for reuse or discharged from high load wastewater treatment plants to recreational areas. For full microbiological safety it would be advisable to apply an additional disinfection method (e.g., ozonation).

Sign in / Sign up

Export Citation Format

Share Document