Effect of Temperature and Gas Flow on Bi2Se3 Nanoplates Grown by Chemical Vapor Deposition

2018 ◽  
Vol 18 (11) ◽  
pp. 7590-7594 ◽  
Author(s):  
Peng Gu ◽  
Jinling Yu ◽  
Xiaolin Zeng ◽  
Shuying Cheng ◽  
Yunfeng Lai ◽  
...  
Keyword(s):  
Chemical Vapor Deposition ◽  
Vapor Deposition ◽  
Gas Flow ◽  
Chemical Vapor ◽  
Effect Of Temperature

Hydrogen Concentration Analysis in Pecvd and Rtcvd Silicon Nitride Thin Films and It's Impact on Device Performance

2001 ◽  
Vol 664 ◽  
Author(s):  
C. Y. Wang ◽  
E. H. Lim ◽  
H. Liu ◽  
J. L. Sudijono ◽  
T. C. Ang ◽  
...  
Keyword(s):  
Chemical Vapor Deposition ◽  
Threshold Voltage ◽  
Vapor Deposition ◽  
Gas Flow ◽  
Chemical Vapor ◽  
Gate Oxide ◽  
Nitride Film ◽  
Device Performance ◽  
Gas Flow Ratio ◽  
The Impact

ABSTRACTIn this paper the impact of the ESL (Etch Stop layer) nitride on the device performance especially the threshold voltage (Vt) has been studied. From SIMS analysis, it is found that different nitride gives different H concentration, [H] in the Gate oxide area, the higher [H] in the nitride film, the higher H in the Gate Oxide area and the lower the threshold voltage. It is also found that using TiSi instead of CoSi can help to stop the H from diffusing into Gate Oxide/channel area, resulting in a smaller threshold voltage drift for the device employed TiSi. Study to control the [H] in the nitride film is also carried out. In this paper, RBS, HFS and FTIR are used to analyze the composition changes of the SiN films prepared using Plasma enhanced Chemical Vapor deposition (PECVD), Rapid Thermal Chemical Vapor Deposition (RTCVD) with different process parameters. Gas flow ratio, RF power and temperature are found to be the key factors that affect the composition and the H concentration in the film. It is found that the nearer the SiN composition to stoichiometric Si3N4, the lower the [H] in SiN film because there is no excess silicon or nitrogen to be bonded with H. However the lowest [H] in the SiN film is limited by temperature. The higher the process temperature the lower the [H] can be obtained in the SiN film and the nearer the composition to stoichiometric Si3N4.

The SiNx films process research by plasma-enhanced chemical vapor deposition in crystalline silicon solar cells

2017 ◽  
Vol 31 (16-19) ◽  
pp. 1744101 ◽  
Author(s):  
Bitao Chen ◽  
Yingke Zhang ◽  
Qiuping Ouyang ◽  
Fei Chen ◽  
Xinghua Zhan ◽  
...  
Keyword(s):  
Thin Film ◽  
Chemical Vapor Deposition ◽  
Solar Cell ◽  
Vapor Deposition ◽  
Gas Flow ◽  
Silicon Solar Cell ◽  
Crystalline Silicon ◽  
Chemical Vapor ◽  
Double Layers ◽  
Crystalline Silicon Solar Cell

SiNx thin film has been widely used in crystalline silicon solar cell production because of the good anti-reflection and passivation effect. We can effectively optimize the cells performance by plasma-enhanced chemical vapor deposition (PECVD) method to change deposition conditions such as temperature, gas flow ratio, etc. In this paper, we deposit a new layer of SiNx thin film on the basis of double-layers process. By changing the process parameters, the compactness of thin films is improved effectively. The NH3passivation technology is augmented in a creative way, which improves the minority carrier lifetime. In sight of this, a significant increase is generated in the photoelectric performance of crystalline silicon solar cell.

Influences of gas flow on chemical vapor deposition of superconducting Nb‐Ge films

1981 ◽  
Vol 39 (4) ◽  
pp. 354-356 ◽  
Author(s):  
Mitsumasa Suzuki ◽  
Hiroshi Onodera ◽  
Takeshi Anayama ◽  
Gin‐ichiro Oya ◽  
Yutaka Onodera
Keyword(s):  
Chemical Vapor Deposition ◽  
Vapor Deposition ◽  
Gas Flow ◽  
Chemical Vapor

scholarly journals Catalyst-Less and Transfer-Less Synthesis of Graphene on Si(100) Using Direct Microwave Plasma Enhanced Chemical Vapor Deposition and Protective Enclosures

Materials ◽  
2020 ◽  
Vol 13 (24) ◽  
pp. 5630
Author(s):  
Rimantas Gudaitis ◽  
Algirdas Lazauskas ◽  
Šarūnas Jankauskas ◽  
Šarūnas Meškinis
Keyword(s):  
Chemical Vapor Deposition ◽  
Vapor Deposition ◽  
Gas Flow ◽  
Microwave Plasma ◽  
Lattice Mismatch ◽  
Chemical Vapor ◽  
Hydrogen Gas ◽  
Synthesis Process ◽  
Synthesis Time ◽  
Graphene Layers

In this study, graphene was synthesized on the Si(100) substrates via the use of direct microwave plasma-enhanced chemical vapor deposition (PECVD). Protective enclosures were applied to prevent excessive plasma etching of the growing graphene. The properties of synthesized graphene were investigated using Raman scattering spectroscopy and atomic force microscopy. Synthesis time, methane and hydrogen gas flow ratio, temperature, and plasma power effects were considered. The synthesized graphene exhibited n-type self-doping due to the charge transfer from Si(100). The presence of compressive stress was revealed in the synthesized graphene. It was presumed that induction of thermal stress took place during the synthesis process due to the large lattice mismatch between the growing graphene and the substrate. Importantly, it was demonstrated that continuous horizontal graphene layers can be directly grown on the Si(100) substrates if appropriate configuration of the protective enclosure is used in the microwave PECVD process.

scholarly journals Growth of diamond by rf plasma-assisted chemical vapor deposition

1988 ◽  
Vol 3 (6) ◽  
pp. 1397-1403 ◽  
Author(s):  
Duane E. Meyer ◽  
Natale J. Ianno ◽  
John A. Woollam ◽  
A. B. Swartzlander ◽  
A. J. Nelson
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Chemical Vapor Deposition ◽  
Vapor Deposition ◽  
Gas Flow ◽  
Chemical Vapor ◽  
Input Power ◽  
Rf Plasma ◽  
Diamond Particles ◽  
Scanning Electron

A system has been designed and constructed to produce diamond particles by inductively coupled radio-frequency, plasma-assisted chemical vapor deposition. This is a low-pressure, low-temperature process used in an attempt to deposit diamond on substrates of glass, quartz, silicon, nickel, and boron nitride. Several deposition parameters have been varied including substrate temperature, gas concentration, gas pressure, total gas flow rate, rf input power, and deposition time. Analytical methods employed to determine composition and structure of the deposits include scanning electron microscopy, absorption spectroscopy, scanning Auger microprobe spectroscopy, and Raman spectroscopy. Analysis indicates that particles having a thin graphite surface, as well as diamond particles with no surface coatings, have been deposited. Deposits on quartz have exhibited optical bandgaps as high as 4 5 eV. Scanning electron microscopy analysis shows that particles are deposited on a pedestal which Auger spectroscopy indicates to be graphite. This is a phenomenon that has not been previously reported in the literature.

Effects of Reaction Conditions on MoS2 Thin Film Formation Synthesized by Chemical Vapor Deposition using Organic Precursor

MRS Advances ◽  
2016 ◽  
Vol 2 (29) ◽  
pp. 1533-1538 ◽  
Author(s):  
S. Ishihara ◽  
Y. Hibino ◽  
N. Sawamoto ◽  
T. Ohashi ◽  
K. Matsuura ◽  
...  
Keyword(s):  
Thin Film ◽  
Chemical Vapor Deposition ◽  
Low Temperature ◽  
Flow Rate ◽  
Vapor Deposition ◽  
Gas Flow ◽  
Film Formation ◽  
Chemical Vapor ◽  
Gas Flow Rate ◽  
Axis Orientation

ABSTRACTMolybdenum disulfide (MoS2) thin films were fabricated by two-step chemical vapor deposition (CVD) using (t-C4H9)2S2 and the effects of temperature, gas flow rate, and atmosphere on the formation were investigated in order to achieve high-speed low-temperature MoS2 film formation. From the results of X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM) investigations, it was confirmed that c-axis orientation of the pre-deposited Mo film has a significant involvement in the crystal orientation after the reaction low temperature sulfurization annealing and we successfully obtained 3 nm c-axis oriented MoS2 thin film. From the S/Mo ratios in the films, it was revealed that the sulfurization reaction proceeds faster with increase in the sulfurization temperature and the gas flow rate. Moreover, the sulfurization under the H2 atmosphere promotes decomposition reaction of (t-C4H9)2S2, which were confirmed by XPS and density functional theory (DFT) simulation.

Surface Modification of Silicon Carbide Powder with Silica Coating by Rotary Chemical Vapor Deposition

2014 ◽  
Vol 616 ◽  
pp. 232-236 ◽  
Author(s):  
Zhen Hua He ◽  
Hirokazu Katsui ◽  
Rong Tu ◽  
Takashi Goto
Keyword(s):  
Silicon Carbide ◽  
Chemical Vapor Deposition ◽  
Vapor Deposition ◽  
Gas Flow ◽  
Deposition Time ◽  
Chemical Vapor ◽  
Silica Coating ◽  
Carbide Powder ◽  
Mass Content ◽  
Vaporization Temperature

The surface of silicon carbide (SiC) powder was modified by coating with amorphous silica (SiO2) using (C2H5O4)Si (tetraethyl orthosilicate: TEOS) as a precursor by rotary chemical vapor deposition (RCVD). With increasing deposition time from 0.9 to 14.4 ks, the mass content of SiO2 coating increased from 1 to 35 mass%. The SiO2 mass content had a linear relationship with deposition time from 2.7 to 7.2 ks. The effects of O2 gas flow, deposition temperature (Tdep), total pressure (Ptot) and precursor vaporization temperature (Tvap) on the SiO2 yield by RCVD were investigated. At O2 gas flow of 4.2 × 10-7 m3 s-1, Tdep of 948 K, Ptot of 400 Pa and deposition time of 7.2 ks, the maximum SiO2 yield of 1.82 × 10-7 kg/s with SiC powder of 4.5 × 10-3 kg by RCVD was obtained.

Sign in / Sign up

Export Citation Format

Share Document