scholarly journals Microstructure and mechanical properties of A357/SiC nanocomposites fabricated by ultrasonic cavitation-based dispersion of ball-milled nanoparticles

2016 ◽  
Vol 51 (3) ◽  
pp. 395-404 ◽  
Author(s):  
Sinan Kandemir
Keyword(s):  
Mechanical Properties ◽  
Tensile Properties ◽  
Ultrasonic Processing ◽  
A357 Alloy ◽  
Sic Nanoparticles ◽  
Uniform Dispersion ◽  
The Matrix ◽  
Electron Microscopes ◽  
Dispersion Of Nanoparticles ◽  
Microstructural Studies

In this work, A357/0.5 wt.% SiC nanocomposites were fabricated with a combination of ultrasonic processing and a nanoparticle feeding mechanism that involves the introduction of a closed end aluminium tube filled with the ball-milled SiC nanoparticles (20–30 nm) and aluminium powders (<75 µm) into the melt for complete deagglomeration and uniform dispersion of nanoparticles through the matrix. The microstructural and mechanical properties of the fabricated nanocomposites were investigated. The microstructural studies conducted with optical and advanced electron microscopes indicate that relatively effective deagglomeration and uniform dispersion of SiC nanoparticles into the molten alloy were achieved. The hardness and tensile properties of the nanocomposites were notably improved compared to those of the ultrasonically processed A357 alloy without reinforcement, showing the strengthening potency of nanoparticles and the good bonding obtained at the particle-reinforcement interface.

Influences of the γ′ Phase on the Mechanical Properties of a Nickel-Based Single Crystal Superalloy

2021 ◽  
Vol 1023 ◽  
pp. 45-52
Author(s):  
Xiao Yan Wang ◽  
Meng Li ◽  
Zhi Xun Wen
Keyword(s):  
Mechanical Properties ◽  
Solid Solution ◽  
Single Crystal ◽  
Tensile Properties ◽  
Room Temperature ◽  
Solution Treatment ◽  
Single Crystal Superalloy ◽  
Original Material ◽  
Solid Solution Treatment ◽  
The Matrix

After solid solution treatment at 1335°C for 4 hours and cooling to room temperature at different rate, the nickel-based single crystal superalloy were made into three kinds of nickel-based single crystal superalloy materials containing different size γ′ phases, respectively. The tensile test of I-shaped specimens was carried out at 980°C, and their effect of γ′ phase microstructure on the tensile properties was studied. The results show that the yielding strength of the material air-cooled to room temperature was lower than that with cooling rate at 0.15°C/s, but both of them were lower than the yielding strength of original material. Little difference was found on the elastic modulus of I-shaped specimens made of three kinds of materials. When the cubic degree of the γ′ phase is higher and the size is larger, the tensile properties of the material is better, which can be attributed to the larger size and narrower channel of the matrix phase that lead to higher dislocation resistance.

scholarly journals Efficient Hydrophobic Modification of Old Newspaper and Its Application in Paper Fiber Reinforced Composites

Polymers ◽  
2019 ◽  
Vol 11 (5) ◽  
pp. 842 ◽  
Author(s):  
Weiwei Zhang ◽  
Jin Gu ◽  
Dengyun Tu ◽  
Litao Guan ◽  
Chuanshuang Hu
Keyword(s):  
Mechanical Properties ◽  
Aspect Ratio ◽  
Natural Fiber ◽  
Fiber Reinforced Composites ◽  
Reinforced Composites ◽  
Fiber Reinforced ◽  
Oh Groups ◽  
Uniform Dispersion ◽  
The Matrix ◽  
Paper Fibers

Paper fibers have gained broad attention in natural fiber reinforced composites in recent years. The specific problem in preparing paper fiber reinforced composites is that paper fibers easily become flocculent after pulverization, which increases difficulties during melt-compounding with polymer matrix and results in non-uniform dispersion of paper fibers in the matrix. In this study, old newspaper (ONP) was treated with a low dosage of gaseous methyltrichlorosilane (MTCS) to solve the flocculation. The modified ONP fibers were characterized by Scanning Electron Microscope (SEM), Fourier Transform Infrared Spectroscopy (FTIR), and Thermogravimetric Analysis (TG). Then the modified ONP fibers and high-density polyethylene (HDPE) were extruded and pelletized to prepare ONP/HDPE composites via injection molding. Maleic anhydride-grafted polyethylene (MAPE) was added to enhance the interfacial bonding performance with the ultimate purpose of improving the mechanical strength of the composites. The mechanical properties such as tensile, flexural, and impact strength and the water absorption properties of the composite were tested. The results showed that the formation of hydrogen bonding between ONP fibers was effectively prevented after MTCS treatment due to the reduction of exposed –OH groups at the fiber surface. Excessive dosage of MTCS led to severe fiber degradation and dramatically reduced the aspect ratio of ONP fibers. Composites prepared with ONP fibers modified with 4% (v/w) MTCS showed the best mechanical properties due to reduced polarity between the fibers and the matrix, and the relatively long aspect ratio of treated ONP fibers. The composite with or without MAPE showed satisfactory water resistance properties. MTCS was proven to be a cheap and efficient way to pretreat old newspaper for preparing paper fiber reinforced composites.

Toughening of Polypropylene Highly Filled with Aluminum Hydroxide

2005 ◽  
Vol 13 (2) ◽  
pp. 139-150 ◽  
Author(s):  
Zhanpai Su ◽  
Pingkai Jiang ◽  
Qiang Li ◽  
Ping Wei ◽  
Yong Zhang
Keyword(s):  
Mechanical Properties ◽  
Tensile Properties ◽  
Aluminum Hydroxide ◽  
Interfacial Adhesion ◽  
Ethylene Propylene Diene Monomer ◽  
The Matrix ◽  
Izod Impact ◽  
Rubbery Phase ◽  
Rubber Phase ◽  
Toughening Agent

The flame retardant and mechanical properties of polypropylene (PP), highly filled with aluminum hydroxide (Al(OH)3) and toughened with ethylene propylene diene monomer (EPDM) and zinc neutralized sulfated EPDM ionomer (Zn-S-EPDM), were studied along with their morphology. The PP matrix when highly filled with Al(OH)3 particles can achieve an adequate level of flame retardancy, but there is a decrease in the mechanical properties because of inadequate adhesion between the Al(OH)3 particles and the PP matrix and the strong tendency of the filler to agglomerate. The rubber incorporated in the PP/Al(OH)3 composites has two roles: as compatibilizer and toughening agent. Although ordinary EPDM significantly improves the Izod impact strength of the composites, the tensile properties are much worse because of the weak interfacial adhesion between the modifier and the matrix. Using Zn-S-EPDM instead EPDM, the tensile properties are much improved with only a slight decrease in toughness, because of improvements in the interfacial adhesion between modifier and matrix. SEM micrographs show that the rubber phase is dispersed in the continuous PP matrix and that most Al(OH)3 particles are uniformly distributed in the rubbery phase. Larger, obviously rubbery, domains can be seen in the PP/EPDM/Al(OH)3 ternary composites. Much finer rubbery domains were found in the PP/Zn-S-EPDM/Al(OH)3 composites.

Processing and Microstructure Characteristics of As-Cast A356 Alloys Manufactured via Ultrasonic Cavitation during Solidification

2017 ◽  
Vol 36 (4) ◽  
pp. 381-387 ◽  
Author(s):  
Yang Xuan ◽  
Shian Jia ◽  
Laurentiu Nastac
Keyword(s):  
Mechanical Properties ◽  
A356 Alloy ◽  
Matrix Alloy ◽  
Ultrasonic Cavitation ◽  
Solidification Processing ◽  
Sic Nanoparticles ◽  
Nanoparticle Distribution ◽  
Microstructure Characteristics ◽  
The Matrix ◽  
Cast Microstructure

AbstractRecent studies have showed that the microstructure and mechanical properties of A356 alloy can be significantly improved when ultrasonic cavitation and solidification processing is used. This is because during the fabrication of A356 castings, ultrasonic cavitation processing plays an important role in degassing and refining the as-cast microstructure. In the present study, A356 alloy and Al2O3/SiC nanoparticles are used as the matrix alloy and the reinforcements, respectively. Nanoparticles are injected into the molten alloy and dispersed by ultrasonic cavitation. Ultrasonic cavitation was also applied during solidification of these nanocomposites. The microstructure and nanoparticle distribution of the cast samples have been investigated in detail. The current experimental results indicated that ultrasonic cavitation during solidification will greatly improve the microstructure of the samples. Al2O3 and SiC nanoparticle reinforced nanocomposites have different nanoparticle distributions in the matrix.

scholarly journals Studies on Water Sorption Behaviour of Laminated Bamboo Polymer Composite

2019 ◽  
Vol 130 ◽  
pp. 01040 ◽  
Author(s):  
Yuniar Ratna Pratiwi ◽  
Indah Widiastuti ◽  
Budi Harjanto
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Tensile Properties ◽  
Water Immersion ◽  
Bamboo Fiber ◽  
Epoxy Composites ◽  
Gravimetric Analysis ◽  
Sorption Behaviour ◽  
Laminated Bamboo ◽  
The Matrix

The aim of this article is to evaluate water absorption in bamboo fiber composites. Bamboo is hydrophilic, means that it easily absorbs water. In this study the bamboo fiber-based composites were developed using hand lay up method, with epoxy resin as the matrix constituent. Water absorption characteristics of specimens of bamboo composite and epoxy were determined from water immersion tests at several temperatures. Gravimetric analysis was performed to determine the moisure absorbed as a function of time at two different temperatures: 25 ºC and 50 C. The diffusivity of water in an epoxy bamboo composite was determined after reaching saturation point. During room temperature soaking, epoxy specimen showed the characteristic of Fickian behavior. Similar immersion tests on bamboo-epoxy composites followed nonfickian behavior. Changes in the mechanical properties of material due to water absorption were evaluated from tensile testing on materials with varied water content. It was found that the waterabsorption in all samples reduced the tensile properties. The degradation of tensile properties was greater with an increasing temperature of immersion. The results of this study emphasize the importance ofconsidering deterioration of mechanical properties in the bamboo epoxy composites during their application in water and possibly in humid environment.

Preparation and Mechanical Properties of Nano-SiCp/Mg Composites by Ultrasonic Dispersion

2010 ◽  
Vol 150-151 ◽  
pp. 792-795 ◽  
Author(s):  
Hong Yan ◽  
Zhi Hu
Keyword(s):  
Mechanical Properties ◽  
Room Temperature ◽  
Ultrasonic Method ◽  
Fracture Morphology ◽  
Dispersion Strengthening ◽  
Ultrasonic Dispersion ◽  
Sic Nanoparticles ◽  
The Matrix ◽  
Dislocation Strengthening ◽  
Magnesium Composites

SiC nanoparticles reinforced AZ61 magnesium composites were fabricated by Ultrasonic method. The distribution of nanoparticles in the matrix and the fracture morphology of the composites were observed by SEM, and the mechanical properties of the composites were tested at room temperature. Experimental shows that SiC nanoparticles were dispersed well in the matrix with the pretreatment method. Compared with the matrix, the tensile strength and hardness of the composites were improved respectively. Meanwhile, the ductility of the composites didn’t be obviously decreased. The enhancement function of nano composites was predicted with the dislocation strengthening and Orowan dispersion strengthening mechanisms. The predicted results coincided well with experimental ones.

Processing, Microstructure and Mechanical Properties of SiCp/AZ91 Mg Matrix Composites Fabricated by Squeeze Casting

2007 ◽  
Vol 546-549 ◽  
pp. 499-502
Author(s):  
X. Qiu ◽  
Xiao Jun Wang ◽  
Ming Yi Zheng ◽  
Kun Wu
Keyword(s):  
Mechanical Properties ◽  
Tensile Properties ◽  
Squeeze Casting ◽  
Volume Fraction ◽  
Matrix Alloy ◽  
Matrix Composites ◽  
Magnesium Matrix Composites ◽  
The Matrix ◽  
Az91 Magnesium ◽  
Different Diameters

The fabrication processing, mechanical properties and fracture characters of SiCp/AZ91 magnesium matrix composites fabricated by squeeze casting were investigated. The SiC particles with different diameters (5μm, 20μm and 50μm) were employed as the reinforcement in the composites, the volume fraction of them was 50% in all cases. Experimental results showed that when the size of SiC particle decreased, the tensile properties of the composite increased. The tensile properties of SiCp/AZ91 composite with small particles are controlled by the properties of matrix alloy and the strength of the interface between the matrix and reinforcements, but the composites reinforced by large particles are controlled by the fracture of the particles.

Physical and Mechanical Properties of Epoxy-Nanoparticulate Composite Adhesive

2012 ◽  
Vol 585 ◽  
pp. 297-300 ◽  
Author(s):  
Prakriti Kumar Ghosh ◽  
Manjeet Singh Goyat ◽  
Deepak Mishra ◽  
Rishabh Nagori
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Glass Transition ◽  
Tensile Properties ◽  
Physical And Mechanical Properties ◽  
Epoxy Adhesive ◽  
Al2o3 Nanoparticles ◽  
Thermal And Mechanical Properties ◽  
Vibration Process ◽  
Dispersion Of Nanoparticles

The effect of type of nanoparticles on morphology, thermal and mechanical properties of epoxy-nanoparticulate composite adhesive produced via ultrasonic vibration process has been investigated. The morphology, thermal and mechanical properties of epoxy-nanoparticulate composite adhesive was measured with FESEM/AFM, DTA/TGA, and Hounsfield respectively. The FESEM/AFM images of the epoxy-nanoparticulate composite adhesive reveals significantly fine dispersion of nanoparticles. The incorporation TiO2 nanoparticles in epoxy adhesive results in improved glass transition temperature (Tg), thermal stability and tensile properties of the nanocomposite. But, the incorporation of comparatively finer size Al2O3 nanoparticles leads to decrease in the Tg, thermal stability and tensile properties of the nanocomposite.

Mechanical Performances of ZTM/SiC Nanocomposite Optimized through Composition and Microstructure Tailoring

2008 ◽  
Vol 569 ◽  
pp. 89-92
Author(s):  
Xi Hai Jin ◽  
Lian Gao ◽  
Jing Sun
Keyword(s):  
Mechanical Properties ◽  
Mechanical Property ◽  
Grain Growth ◽  
Sic Nanoparticles ◽  
Microstructure And Mechanical Properties ◽  
The Matrix ◽  
Mechanical Performances

SiC/ZTM nanocomposites were prepared, and the influence of nanosized SiC addition on the microstructure and mechanical properties were investigated. It was found that the addition of nanosized SiC significantly retarded the matrix grain growth, making the microstructure much finer and more uniform. This led to a significant improvement in the mechanical properties. And further enhancement in the mechanical property can be achieved through the addition of mullite seeds in the starting powder and improving the distribution homogeneity of SiC nanoparticles in the matrix.

Mechanical Properties and Microstrutures of Nano-Sized SiC Particles Reinforced AZ91D Nanocomposites Fabricated by High Intensity Ultrasonic Assisted Casting

2009 ◽  
Vol 618-619 ◽  
pp. 449-452 ◽  
Author(s):  
Shi Ying Liu ◽  
Fei Peng Gao ◽  
Qiong Yuan Zhang ◽  
Wen Zhen Li
Keyword(s):  
Mechanical Properties ◽  
High Intensity ◽  
Intermediate Phase ◽  
Casting Method ◽  
Magnesium Matrix ◽  
Alloy Matrix ◽  
Sic Nanoparticles ◽  
The Matrix ◽  
Ultrasonic Assisted ◽  
Matrix Nanocomposites

A high intensity ultrasonic assisted casting method was used to fabricate SiC nanoparticles reinforced magnesium matrix nanocomposites (n-SiCp/AZ91D). The microstructures and mechanical properties of the nanocomposites were investigated. The results show that n-SiCp are well dispersed in the matrix and the grain size was refined. A HRTEM study of the interface between n-SiCp and the matrix suggests that SiC bonds well with matrix without forming an intermediate phase. With the lower addition of n-SiCp, the mechanical properties of nanocomposites are greatly improved. As compared to an unreinforced magnesium alloy matrix, the tensile and yield strength were improved by 43.6% and 117% respectively.

Sign in / Sign up

Export Citation Format

Share Document