Mechanical and Dynamic Mechanical Analysis of PBO Paper-based Composites

2021 ◽  
pp. 004051752110563
Author(s):  
Ziqi Huang ◽  
Yi Wang ◽  
Jin Long ◽  
Jian Hu
Keyword(s):  
Tensile Strength ◽  
Experimental Studies ◽  
Dynamic Mechanical Properties ◽  
Mechanical Analysis ◽  
Raw Material ◽  
Wall Material ◽  
Dynamic Mechanical ◽  
Comparative Results ◽  
Tearing Resistance ◽  
Resistance Value

Poly ( p-phenylene benzoisoxazole; PBO) paper is a potential raw material for use in honeycomb sandwich composites in the aerospace industry, which are able to sustain high temperatures exceeding 300°C. This work presents a wet-forming method of making PBO paper, consisting of PBO chopped fibers. The paper was impregnated with phenolic resin to simulate honeycomb wall material. The structure and mechanical and dynamic mechanical properties of the raw and impregnated paper were characterized. The performance of PBO paper was tested against p-aramid paper. The comparative results showed the tensile strength of PBO raw paper was 2.17 kN/m, which was slightly worse than p-aramid raw paper: 2.66 kN/m. After impregnation, the tensile strength of the PBO paper was 13.93 kN/m due to the increase in the number of bonding points—better than p-aramid paper: 7.99 kN/m. The tearing resistance value for PBO raw paper versus p-aramid raw paper was 3252 mN against 845 mN. The morphology of the torn samples in the impregnated paper revealed higher levels of PBO fiber pullout than p-aramid fiber, therefore the tearing resistance value was 6000 mN for PBO impregnated paper, which was again superior to p-aramid impregnated paper: 675 mN. The PBO paper also showed higher storage modulus than p-aramid paper after impregnation. Experimental studies showed that PBO paper could be used in load-bearing structures and in honeycomb components where high resistance to deformation and thermal stability is necessary.

scholarly journals Styrene–Acrylic Emulsion with “Transition Layer” for Damping Coating: Synthesis and Characterization

Polymers ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1406
Author(s):  
Daoyuan Chen ◽  
Mingjin Ding ◽  
Zhixiong Huang ◽  
Yanbing Wang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Transition Layer ◽  
Testing Machine ◽  
Dynamic Mechanical Properties ◽  
Mechanical Analysis ◽  
Latex Film ◽  
Seeded Emulsion Polymerization ◽  
Acrylic Emulsion ◽  
Dynamic Mechanical

In order to study the dynamic mechanical properties of styrene–acrylic latex with a core/shell structure, a variety of latexes were synthesized by semi-continuous seeded emulsion polymerization based on “particle design” with the same material. The latexes were characterized by rotary viscosimeter, dynamic light scattering (DLS), Fourier transform infrared spectroscopy (FTIR), transmission electron microscope (TEM), dynamic mechanical analysis (DMA), and universal testing machine. The effects of difference at the glass transition temperature (Tg) of core and shell and the introduction of the “transition layer” on the damping and mechanical properties of latex film were studied. The results indicate that as the Tg of core and shell gets closer, the better the compatibility of core and shell, from phase separation to phase continuity. Furthermore, the introduction of the “transition layer” can effectively improve the tensile strength and tan δ (max) of the latex film. The tensile strength and maximum loss factor (f = 1 Hz) of latex with the “transition layer” increased by 36.73% and 29.11% respectively compared with the latex without the “transition layer”. This work provides a reference for the design of emulsion for damping coating.

scholarly journals Investigation of viscoelastic properties and thermal behavior of photocurable epoxy acrylate nanocomposites

2017 ◽  
Vol 24 (5) ◽  
pp. 691-697
Author(s):  
Behzad Shirkavand Hadavand ◽  
Hossein Hosseini
Keyword(s):  
Thermal Behavior ◽  
Dynamic Mechanical Properties ◽  
Mechanical Analysis ◽  
Cuo Nanoparticles ◽  
Epoxy Acrylate ◽  
Silane Coupling Agents ◽  
Scanning Calorimetry ◽  
Dynamic Mechanical ◽  
Acrylate Resin ◽  
Epoxy Acrylate Resin

AbstractIn this study, the dynamic-mechanical properties and thermal behavior of the nanocomposites of a photocurable epoxy-acrylate resin and CuO nanohybrid were determined. In order to improve the dispersion of CuO nanoparticles and prevention of nanoparticle migration to the surface coating, the surface of commercial nanoparticles was modified by triethoxymethylsilane (TEMS) and vinyltrimethoxysilane (VTMS) as silane-coupling agents. Dynamic mechanical analysis (DMA), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC) tests were then performed on CuO-filled epoxy-acrylate resins to identify the loading effect on the properties of material. The thermal stability of nanocomposites was affected slightly after incorporation of CuO nanoparticles. DMA studies revealed that filling the CuO nanoparticles into epoxy-acrylate resin can produce a significant enhancement in storage modulus, as well as a shift in the glass transition temperature. The films reinforced with the modified CuO exhibit the most significant enhancements in properties.

scholarly journals Dynamic Mechanical Properties of Hybrid Layered Silicates/Kaolin Geopolymer Filler in Epoxy Composites

2017 ◽  
Vol 54 (3) ◽  
pp. 543-545 ◽  
Author(s):  
Yusrina Mat Daud ◽  
Kamarudin Hussin ◽  
Azlin Fazlina Osman ◽  
Che Mohd Ruzaidi Ghazali ◽  
Mohd Mustafa Al Bakri Abdullah ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Speed ◽  
Hybrid Composites ◽  
Loss Modulus ◽  
Dynamic Mechanical Properties ◽  
Mechanical Analysis ◽  
Layered Silicates ◽  
Epoxy Composites ◽  
Damping Factor ◽  
Dynamic Mechanical

Preparation epoxy based hybrid composites were involved kaolin geopolymer filler, organo-montmorillonite at 3phr by using high speed mechanical stirrer. A mechanical behaviour of neat epoxy, epoxy/organo-montmorillonite and its hybrid composites containing 1-8phr kaolin geopolymer filler was studied upon cyclic deformation (three-point flexion mode) as the temperature is varies. The analysis was determined by dynamic mechanical analysis (DMA) at frequency of 1.0Hz. The results then expressed in storage modulus (E�), loss modulus (E�) and damping factor (tan d) as function of temperature from 40 oC to 130oC. Overall results indicated that E�, E�� and Tg increased considerably by incorporating optimum 1phr kaolin geopolymer in epoxy organo-montmorillonite hybrid composites.

scholarly journals THE INFLUENCE OF SEVERAL TYPES OF RESINS ON THE DYNAMIC MECHANICAL PROPERTIES OF POLYMER MIXTURE BASED ON BUTYL RUBBER

2020 ◽  
Vol 3 (2) ◽  
pp. 36-45 ◽  
Author(s):  
O. Tarasova ◽  
Yu. Yurkin ◽  
A. Toroschin
Keyword(s):  
Phenol Formaldehyde ◽  
Dynamic Properties ◽  
Dynamic Mechanical Properties ◽  
Mechanical Analysis ◽  
Strength Properties ◽  
Butyl Rubber ◽  
Polymer Materials ◽  
Polymer Mixture ◽  
Damping Properties ◽  
Dynamic Mechanical

this work is devoted to the problem of developing vibration-damping polymer materials with high damping properties in a wide temperature range. The study of the effect of modifying additives on the strength, damping, adhesive and cohesive properties of a butyl rubber composite is the aim of this work. The task is to identify the actual temperature, frequency, dynamic and mechanical characteristics of a composite material based on butyl rubber depending on the type and concentration of resins. The key methods for studying this problem is the dynamic mechanical analysis method, aimed at obtaining information about changes in the dynamic properties of polymer materials (bond strength with metal when peeling samples of composites, determining the flow resistance of samples, determining the migration of plasticizer). Due to the established experimental dependences, it was found that the addition of resins (3% by weight) in the composition based on butyl rubber leads to an increase in the damping properties of composite materials, and an increase to (4.25% by weight) leads to their decrease. It was established that the obtained filled mixtures with a high damping peak and good adhesive and strength properties are mixtures with the addition of alkyl phenol-formaldehyde resins.

scholarly journals Preparation and Component Optimization of Resin-Based Permeable Brick

Materials ◽  
2020 ◽  
Vol 13 (12) ◽  
pp. 2701
Author(s):  
Xiaofu Wang ◽  
Xiong Zhang
Keyword(s):  
Particle Diameter ◽  
Characteristic Parameter ◽  
Dynamic Mechanical Properties ◽  
Mechanical Analysis ◽  
Fine Aggregate ◽  
Test Results ◽  
Dynamic Mechanical ◽  
Aggregate Distribution ◽  
Particle Group ◽  
Selection Of

The present study aims to prepare resin-based permeable bricks with micron-sized pores using fine aggregate with a particle diameter of 0.08–0.6 mm and bisphenol-A epoxy resin, a polymer binder. The properties of the binder, the characteristic parameters of the aggregate, and the micro pore structure of the brick were studied in order to break through the limitations of traditional porous permeable materials. The dynamic mechanical properties of resin were analyzed by dynamic mechanical analysis (DMA). The frequency parameter of particle size of 10 kinds of aggregate from different regions were obtained by digital image processing, and the characteristic parameter (aggregate distribution coefficient α) was obtained by modified Gaussian distribution. The microstructure of porous brick was analyzed by scanning electron microscopy-energy-dispersive X-ray spectroscopy (SEM-EDS). The test results show: (1) the glass transition temperature (Tg) of the resin is 61 °C; (2) the parameters of aggregate particle group will affect the performance of porous permeable materials; (3) the minimum effective pore diameter of the permeable brick is 30 μm, the maximum permeable rate is 6.22 × 10 − 2   cm / s and the compressive strength is 41.08 MPa. The conclusions of this study will provide an important reference for permeable materials in the micron-scale pore range and the selection of binder and aggregate materials.

Preparation of high-strength SEBS nanocomposites reinforced with halloysite nanotube: Effect of SEBS-g-MA compatibilizer

2019 ◽  
Vol 33 (10) ◽  
pp. 1336-1357 ◽  
Author(s):  
Nazlı Arman ◽  
Emre Tekay ◽  
Sinan Şen
Keyword(s):  
Tensile Strength ◽  
Elastic Modulus ◽  
Maleic Anhydride ◽  
Storage Modulus ◽  
Tensile Modulus ◽  
Dynamic Mechanical Properties ◽  
Thermal Stabilities ◽  
Halloysite Nanotube ◽  
Dynamic Mechanical ◽  
Strength And Toughness

Poly(styrene -b-ethylene- co-butylene -b-styrene) (SEBS)/organophilic halloysite nanotube (Org-HNT) nanocomposites were prepared by solution mixing and then compression molded. Maleic anhydride grafted SEBS (SEBS- g-MA) was also used as a compatibilizer in preparation of SEBS/SEBS- g-MA/Org-HNT ternary nanocomposites. Surface morphologies and both static and dynamic mechanical analyses as well as thermal stabilities of the nanocomposites were carried out. Both the binary and ternary nanocomposites exhibited higher tensile moduli, tensile strength, and toughness values compared to neat SEBS. The elastic modulus was found to increase about 385% and 320% with addition of 3 and 5 phr Org-HNT into the SEBS matrix, respectively, while the maximum toughness was achieved via SEBS-5H composite with an increase of 45%. The ternary nanocomposite having 3 phr Org-HNT and 10 phr SEBS- g-MA (3H10SMA) gave about a 325% and 103% increase in the elastic modulus and toughness, respectively, together with a 75% increase in the tensile strength as the maximum value. This result was ascribed to interactions of the surface of the nanotubes with the maleic anhydride (MA) group of the compatibilizer. The same nanocomposite was also found to have two times higher dynamic storage modulus at 25°C than neat SEBS and almost the same damping value, which is an indication of improvement in the elastic character of SEBS without impairing its damping ability. Although a much higher damping value was obtained via use of 20 phr SEBS- g-MA with the same amount of nanotubes, the corresponding storage modulus decreased too much, close to that of neat SEBS. The enhanced tensile modulus, strength, and toughness of the 3H10SMA nanocomposite, which is consistent with its dynamic mechanical properties, indicate a good balance between the toughness/damping and stiffness. Moreover, all the nanocomposites exhibited better thermal stabilities than neat SEBS, showing higher midpoint degradation temperatures and peak maximum temperatures at which the maximum degradation occurs.

Thermal stability and dynamic mechanical behavior of functional multiphase boride ceramics/epoxy composites

2019 ◽  
Vol 39 (6) ◽  
pp. 508-514
Author(s):  
Yannan He ◽  
Zhiqiang Yu
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Loss Modulus ◽  
Dynamic Mechanical Properties ◽  
Mechanical Analysis ◽  
Epoxy Composites ◽  
Scanning Calorimetry ◽  
Element Analysis ◽  
Reaction Heat ◽  
Dynamic Mechanical

Abstract The thermal and dynamic mechanical properties of epoxy composites filled with zirconium diboride/nano-alumina (ZrB2/Al2O3) multiphase particles were investigated by means of differential scanning calorimetry, dynamic thermo-mechanical analysis, and numerical simulation. ZrB2/Al2O3 particles were surface organic functional modified by γ-glycidoxypropyltrimethoxysilane for the improvement of their dispersity in epoxy matrix. The results indicated that the curing exotherm of epoxy resin decreased significantly due to the addition of ZrB2/Al2O3 multiphase particles. In comparison to the composites filled with unmodified particles, the modified multiphase particles made the corresponding filling composites exhibit lower curing reaction heat, lower loss modulus, and higher storage modulus. Generally speaking, the composites filled with 5 wt% modified multiphase particles presented the best thermal stability and thermo-mechanical properties due to the better filler-matrix interfacial compatibility and the uniform dispersity of modified particles. Finite element analysis also suggested that the introduction of modified ZrB2/Al2O3 multiphase particles increased the stiffness of the corresponding composites.

scholarly journals Study on dynamic mechanical properties of a nylon-like polyester tire cord

2019 ◽  
Vol 14 ◽  
pp. 155892501986880 ◽  
Author(s):  
Liyong Tian ◽  
Di Wang ◽  
Qufu Wei
Keyword(s):  
Mechanical Properties ◽  
Complex Modulus ◽  
Nylon 6 ◽  
Dynamic Mechanical Properties ◽  
Mechanical Analysis ◽  
Vital Role ◽  
Tire Cord ◽  
Synthetic Fibers ◽  
Dynamic Mechanical ◽  
Polyester Cord

Tires might be the first technically significant composite out of rubber and play a vital role in the overall performance of a car. The essential functions of a tire rely to a great extent on the properties of tire cords. Polyester and nylon cords make up the majority of synthetic fibers used in tires. A new kind of polyester cord has been developed combining the performance characteristics of both polyester and nylon cords. This article examines the dynamic mechanical properties of this nylon-like polyester tire cord by adopting dynamic mechanical analysis, Instron, and DISC fatigue experiments, as well as its dynamic adhesion property using flex fatigue experiment. It demonstrated that the dynamic complex modulus of the nylon-like polyester cord was higher than that of nylon 6 cord but lower than that of standard polyester cord, which was a favorable characteristic when it came to replacing nylon 6 cord with nylon-like polyester cord in tires. Under cyclic loading, hysteresis loss of nylon 6 cord > nylon 66 cord > nylon-like polyester cord > standard polyester cord was observed. In the DISC experiment, nylon-like polyester had a similar compression resistance property to that of nylon 6 cord. At a temperature below 85°C, nylon-like polyester cord maintained roughly the same level of residual ratio of dynamic adhesion, but beyond this temperature point, nylon 6 exhibited a better performance.

PLA-coated sisal fibre-reinforced polyester composite: Water absorption, static and dynamic mechanical properties

2018 ◽  
Vol 53 (1) ◽  
pp. 65-72 ◽  
Author(s):  
MK Gupta ◽  
Rohit Singh
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Loss Modulus ◽  
Alkali Treatment ◽  
Dynamic Mechanical Properties ◽  
Mechanical Analysis ◽  
Static Properties ◽  
Physical Treatment ◽  
Sisal Fibre ◽  
Dynamic Mechanical

In the present work, a novel physical treatment (PLA coating) of sisal fibres and its influence on the water absorption, static and dynamic mechanical properties of its composites has been presented. The treated sisal fibres were used consisted of alkali treatment and PLA coating to fabricate its polyester-based composites by hand lay-up technique keeping constant fibres content as 20 wt.% . Water absorption analysis was carried out in terms of water uptake (%), and sorption, diffusion and permeability coefficient. In addition, static properties were examined in terms of tensile, flexural and impact test, and dynamic mechanical analysis was performed in terms of storage modulus [Formula: see text], loss modulus [Formula: see text], damping [Formula: see text] and glass transition temperature [Formula: see text]. It was reported that the PLA-coated sisal composites showed the best performance in water absorption, mechanical and dynamic mechanical properties than pure sisal and alkali-treated sisal composites. There were 33%, 49%, 48%, and 27% improvement in water resistance, tensile strength, flexural strength and impact strength, respectively, of PLA-coated sisal composites as compared to that of pure sisal composite.

Sign in / Sign up

Export Citation Format

Share Document