Fiber Blending Irregularities in Cross Sections and on Yarn Surfaces in Relation to Yarn Properties

1988 ◽  
Vol 58 (5) ◽  
pp. 291-298 ◽  
Author(s):  
Izabella Krucińnska
Keyword(s):  
Surface Analysis ◽  
Cross Sections ◽  
Original Method ◽  
New Method ◽  
Cross Sectional ◽  
Yarn Properties ◽  
Yarn Surface ◽  
Fiber Blending

An analysis of fiber blending irregularities is presented in relation to the disturbances of blend yarn properties resulting from these phenomena. Fiber blending irregularities were assessed using the original method of yarn surface analysis and a new method of yarn cross-sectional division. These methods correctly reflect the disturbances in the mechanical and aesthetic yarn properties resulting from non-uniform mixing of constituent fibers.

scholarly journals Blending effect of rotor spun yarn with different blending methods

2019 ◽  
Vol 70 (05) ◽  
pp. 403-407
Author(s):  
RUI HUA YANG ◽  
QIAN QIAN DENG ◽  
CHUN PING XIE ◽  
WEI DONG GAO
Keyword(s):  
Mechanical System ◽  
Cross Sections ◽  
New Method ◽  
Cross Sectional ◽  
Blend Ratio ◽  
Rotor Spinning ◽  
Spun Yarn ◽  
Blending Method ◽  
Spun Yarns ◽  
Rotor Spun Yarn

Color blended rotor spun yarn mixing with different methods were spun. Three blending methods were used, one passage of drawing, three passages of drawing and rovings during multi-channel spinning. Multi-channel spinning is modified on rotor spinning machine, which is implemented by a novel mechanical system specially designed to incorporate three separate feed rollers side by side and controlled by servo motors with PLC. Using this new method, blend ratio of yarn can be controlled and realized by asynchronous drafted rovings. 37 type of color blend yarn were produced with different blending ratios. And each yarn was intercepted with 5 cross sections and a total of 185 cross-sectional images were taken. Hamilton index of different colored fibers were calculated of the each type of yarns. And sum of absolute values of Hamilton index were got to demonstrated fibers blending effect in yarns cross sections. All the Hamilton index of the yarns prepared by the three above mentioned methods were all around 5, much below 20. The results showed that regardless of blending method used, the blending effects of rotor spun yarns were all very good.

Gender determination of caucasoid hair using image analysis

1993 ◽  
Vol 51 ◽  
pp. 216-217
Author(s):  
T.B. Ball ◽  
W.M. Hess
Keyword(s):  
Image Analysis ◽  
Cross Sections ◽  
Scalp Hair ◽  
The Body ◽  
Equivalent Diameter ◽  
Cross Sectional ◽  
Hair Samples ◽  
Length Width ◽  
Morphological Differences

It has been demonstrated that cross sections of bundles of hair can be effectively studied using image analysis. These studies can help to elucidate morphological differences of hair from one region of the body to another. The purpose of the present investigation was to use image analysis to determine whether morphological differences could be demonstrated between male and female human Caucasian terminal scalp hair.Hair samples were taken from the back of the head from 18 caucasoid males and 13 caucasoid females (Figs. 1-2). Bundles of 50 hairs were processed for cross-sectional examination and then analyzed using Prism Image Analysis software on a Macintosh llci computer. Twenty morphological parameters of size and shape were evaluated for each hair cross-section. The size parameters evaluated were area, convex area, perimeter, convex perimeter, length, breadth, fiber length, width, equivalent diameter, and inscribed radius. The shape parameters considered were formfactor, roundness, convexity, solidity, compactness, aspect ratio, elongation, curl, and fractal dimension.

Automated 3D measurement of fiber cross section morphology in handsheets

2012 ◽  
Vol 27 (2) ◽  
pp. 264-269 ◽  
Author(s):  
Christian Lorbach ◽  
Ulrich Hirn ◽  
Johannes Kritzinger ◽  
Wolfgang Bauer
Keyword(s):  
Image Analysis ◽  
Cross Section ◽  
Cross Sections ◽  
Image Plane ◽  
3D Measurement ◽  
Cross Sectional ◽  
Fiber Cross Section ◽  
Fiber Wall ◽  
Sectional Shape ◽  
Cross Section Geometry

Abstract We present a method for 3D measurement of fiber cross sectional morphology from handsheets. An automated procedure is used to acquire 3D datasets of fiber cross sectional images using an automated microtome and light microscopy. The fiber cross section geometry is extracted using digital image analysis. Simple sample preparation and highly automated image acquisition and image analysis are providing an efficient tool to analyze large samples. It is demonstrated that if fibers are tilted towards the image plane the images of fiber cross sections are always larger than the true fiber cross section geometry. In our analysis the tilting angles of the fibers to the image plane are measured. The resulting fiber cross sectional images are distorted to compensate the error due to fiber tilt, restoring the true fiber cross sectional shape. We use an approximated correction, the paper provides error estimates of the approximation. Measurement results for fiber wall thickness, fiber coarseness and fiber collapse are presented for one hardwood and one softwood pulp.

scholarly journals Thermo-Hydraulic Performance of U-Tube Borehole Heat Exchanger with Different Cross-Sections

2021 ◽  
Vol 13 (6) ◽  
pp. 3255
Author(s):  
Aizhao Zhou ◽  
Xianwen Huang ◽  
Wei Wang ◽  
Pengming Jiang ◽  
Xinwei Li
Keyword(s):  
Heat Transfer ◽  
Heat Exchange ◽  
Heat Resistance ◽  
Cross Sections ◽  
Three Dimensional ◽  
Thermal Response ◽  
Transfer Efficiency ◽  
Cross Sectional ◽  
Heat Transfer Efficiency ◽  
Oval Tube

For reducing the initial GSHP investment, the heat transfer efficiency of the borehole heat exchange (BHE) system can be enhanced to reduce the number or depth of drilling. This paper proposes a novel and simple BHE design by changing the cross-sectional shape of the U-tube to increase the heat transfer efficiency of BHEs. Specifically, in this study, we (1) verified the reliability of the three-dimensional numerical model based on the thermal response test (TRT) and (2) compared the inlet and outlet temperatures of the different U-tubes at 48 h under the premise of constant leg distance and fluid area. Referent to the circular tube, the increases in the heat exchange efficiencies of the curved oval tube, flat oval tube, semicircle tube, and sector tube were 13.0%, 19.1%, 9.4%, and 14.8%, respectively. (3) The heat flux heterogeneity of the tubes on the inlet and outlet sides of the BHE, in decreasing order, is flat oval, semicircle, curved oval, sector, and circle shapes. (4) The temperature heterogeneity of the borehole wall in the BHE in decreasing order is circle, sector, curved oval, flat oval, and semicircle shapes. (5) Under the premise of maximum leg distance, referent to the heat resistance of the tube with a circle shape at 48 h, the heat exchange efficiency of the curved oval, flat oval, semicircle, and sector tubes increased 12.6%, 17.7%, 10.3%, and 7.8%, respectively. (6) We found that the adjustments of the leg distance and the tube shape affect the heat resistance by about 25% and 12%, respectively. (7) The flat-oval-shaped tube at the maximum leg distance was found to be the best tube design for BHEs.

Application of a Novel Modified Electrode Based on NaY-Encapsulated Co(PAN) Complex

2008 ◽  
Vol 587-588 ◽  
pp. 109-113
Author(s):  
C. Teixeira ◽  
P. Parpot ◽  
Isabel Neves ◽  
António Maurício C. Fonseca
Keyword(s):  
Cyclic Voltammetry ◽  
Chemical Analysis ◽  
Aqueous Medium ◽  
Surface Analysis ◽  
Modified Electrode ◽  
Modified Electrodes ◽  
Redox Properties ◽  
New Method ◽  
Y Zeolite

CoPAN complex has been entrapped in the supercages of Y zeolite and the redox properties of this zeolite-encapsulated complex were investigated by cyclic voltammetry with a new method for the preparation of carbon toray-zeolite-modified electrode. Formation of the CoPAN complex was ascertained by surface analysis (SEM, XRD), chemical analysis (CA), spectroscopy methods (FTIR and UV/vis) and cyclic voltammetry in aqueous medium with zeolite-modified electrodes. The cyclic voltammetry studies obtained with a zeolite-modified electrode shows evidence for electroactivity restricted to boundary associated CoPAN complex.

Comparison of the Cross Sectional Area, the Loss in Volume and the Mechanical Properties of LAE442 and MgCa0.8 as Resorbable Magnesium Alloy Implants after 12 Months Implantation Duration

2010 ◽  
Vol 638-642 ◽  
pp. 675-680 ◽  
Author(s):  
Martina Thomann ◽  
Nina von der Höh ◽  
Dirk Bormann ◽  
Dina Rittershaus ◽  
C. Krause ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Cross Sections ◽  
Degradation Process ◽  
Cross Sectional Area ◽  
Bending Test ◽  
Sectional Area ◽  
Cross Sectional ◽  
Initial Strength ◽  
Three Point Bending ◽  
The Cross

Current research focuses on magnesium based alloys in the course of searching a resorbable osteosynthetic material which provides sufficient mechanical properties besides a good biocompatibility. Previous studies reported on a favorable biocompatibility of the alloys LAE442 and MgCa0.8. The present study compared the degradation process of cylindrical LAE442 and MgCa0.8 implants after 12 months implantation duration. Therefore, 10 extruded implants (2.5 x 25 mm, cross sectional area 4.9 mm²) of both alloys were implanted into the medullary cavity of both tibiae of rabbits for 12 months. After euthanization, the right bone-implant-compound was scanned in a µ-computed tomograph (µCT80, ScancoMedical) and nine uniformly distributed cross-sections of each implant were used to determine the residual implants´ cross sectional area (Software AxioVisionRelease 4.5, Zeiss). Left implants were taken out of the bone carefully. After weighing, a three-point bending test was carried out. LAE442 implants degraded obviously slower and more homogeneously than MgCa0.8. The mean residual cross sectional area of LAE442 implants was 4.7 ± 0.07 mm². MgCa0.8 showed an area of only 2.18 ± 1.03 mm². In contrast, the loss in volume of LAE442 pins was more obvious. They lost 64 % of their initial weight. The volume of MgCa0.8 reduced clearly to 54.4 % which corresponds to the cross sectional area results. Three point bending tests revealed that LAE442 showed a loss in strength of 71.2 % while MgCa0.8 lost 85.6 % of its initial strength. All results indicated that LAE442 implants degraded slowly, probably due to the formation of a very obvious degradation layer. Degradation of MgCa0.8 implants was far advanced.

Effects of Nano-Nozzles Cross-Sectional Geometry on Fluid Flow: Molecular Dynamic Simulation

2017 ◽  
Vol 34 (5) ◽  
pp. 667-678 ◽  
Author(s):  
H. Nowruzi ◽  
H. Ghassemi
Keyword(s):  
Fluid Flow ◽  
Velocity Profile ◽  
Cross Sections ◽  
Md Simulation ◽  
Flow Behavior ◽  
Water Model ◽  
Physical Parameters ◽  
Cross Sectional ◽  
Behavior Characteristics ◽  
Fanning Friction Factor

AbstractNano-nozzles are an essential part of the nano electromechanical systems (NEMS). Cross-sectional geometry of nano-nozzles has a significant role on the fluid flow inside them. So, main purpose of the present study is related to the effects of different symmetrical cross-sections on the fluid flow behavior inside of nano-nozzles. To this accomplishment, five different cross-sectional geometries (equilateral triangle, square, regular hexagon, elliptical and circular) are investigated by using molecular dynamics (MD) simulation. In addition, TIP4P is used for atomistic water model. In order to evaluate the fluid flow behavior, non-dimensional physical parameters such as Fanning friction factor, velocity profile and density number are analyzed. Obtained results are shown that the flow behavior characteristics appreciably depend on the geometry of nano-nozzle's cross-section. Velocity profile and density number for five different cross sections of nano-nozzle at three various measurement gauges are presented and discussed.

Constraint-Based Reverse Engineering From Ultrasound Cross-Sections

1997 ◽  
Author(s):  
Jai Menon ◽  
Ranjit Desai ◽  
Jay Buckey
Keyword(s):  
Reverse Engineering ◽  
Cross Sections ◽  
Biomedical Applications ◽  
Engineering Application ◽  
Volume Data ◽  
Cross Sectional ◽  
Reverse Engineer ◽  
Network Bandwidth ◽  
Complex Topology

Abstract This paper extends the “cross-sectional” approach for reverse engineering, used abundantly in biomedical applications, to the mechanical domain. We propose a combination of “projective” and cross-sectional algorithms for handling physical artifacts with complex topology and geometry. In addition, the paper introduces the concept of constraint-based reverse engineering, where the constraint parameters could include one or more of the following: time, storage (memory, disk-space), network bandwidth, Quality of Service (output-resolution), and so forth. We describe a specific reverse-engineering application which uses ultrasound (tilt-echo) imaging to reverse engineer spatial enumeration (volume) representations from cross-sectional data. The constraint here is time, and we summarize how our implementation can satisfy real-time reconstruction for distribution of the volume data on the internet. We present results that show volume representations computed from static objects. Since the algorithms are tuned to satisfy time constraints, this method is extendable to reverse engineer temporally-varying (elastic) objects. The current reverse engineering processing time is constrained by the data-acquisition (tilt-echo imaging) process, and the entire reverse engineering pipeline has been optimized to compute incremental volume representations in the order of 3 seconds on a network of four processors.

A semi-automated measurement of muscle fiber size using the Imaris software

2021 ◽  
Author(s):  
Jennifer E. Gilda ◽  
Joon-Hyuk Ko ◽  
Aviv-Yvonne Elfassy ◽  
Nadav Tropp ◽  
Anna Parnis ◽  
...  
Keyword(s):  
Muscle Atrophy ◽  
Muscle Fiber ◽  
Cross Sections ◽  
Statistical Tests ◽  
Muscle Fibers ◽  
Fluorescent Labeling ◽  
Cross Sectional ◽  
Short Period ◽  
Fiber Size ◽  
Specific Protease

The size and shape of skeletal muscle fibers are affected by various physiological and pathological conditions, such as muscle atrophy, hypertrophy, regeneration, and dystrophies. Hence, muscle fiber cross-sectional area (CSA) is an important determinant of muscle health and plasticity. We adapted the Imaris software to automatically segment muscle fibers based on fluorescent labeling of the plasma membrane, and measure muscle fiber CSA. Analysis of muscle cross sections by the Imaris semi-automated and manual approaches demonstrated a similar decrease in CSA of atrophying muscles from fasted mice compared with fed controls. In addition, we previously demonstrated that downregulation of the Ca2+-specific protease calpain-1 attenuates muscle atrophy. Accordingly, both the Imaris semi-automated and manual approaches showed a similar increase in CSA of fibers expressing calpain-1 shRNA compared with adjacent non-transfected fibers in the same muscle cross section. Although both approaches seem valid for measurements of muscle fiber size, the manual marking method is less preferable because it is highly time-consuming, subjective, and limits the number of cells that can be analyzed. The Imaris semi-automated approach is user-friendly, requires little training or optimization, and can be used to efficiently and accurately mark thousands of fibers in a short period of time. As a novel addition to the commonly used statistics, we also describe statistical tests that quantify the strength of an effect on fiber size, enabling detection of significant differences between skewed distributions that would otherwise not be detected using typical methods.

Simulation of Flow Field on a Large Scale Wind Turbine

2008 ◽  
Author(s):  
I. Janajreh ◽  
C. Ghenai
Keyword(s):  
Flow Field ◽  
Wind Energy ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Cross Sections ◽  
Large Scale ◽  
Wind Farms ◽  
Operating Characteristics ◽  
Cross Sectional ◽  
Capital Costs

Large scale wind turbines and wind farms continue to evolve mounting 94.1GW of the electrical grid capacity in 2007 and expected to reach 160.0GW in 2010 according to World Wind Energy Association. They commence to play a vital role in the quest for renewable and sustainable energy. They are impressive structures of human responsiveness to, and awareness of, the depleting fossil fuel resources. Early generation wind turbines (windmills) were used as kinetic energy transformers and today generate 1/5 of the Denmark’s electricity and planned to double the current German grid capacity by reaching 12.5% by year 2010. Wind energy is plentiful (72 TW is estimated to be commercially viable) and clean while their intensive capital costs and maintenance fees still bar their widespread deployment in the developing world. Additionally, there are technological challenges in the rotor operating characteristics, fatigue load, and noise in meeting reliability and safety standards. Newer inventions, e.g., downstream wind turbines and flapping rotor blades, are sought to absorb a larger portion of the cost attributable to unrestrained lower cost yaw mechanisms, reduction in the moving parts, and noise reduction thereby reducing maintenance. In this work, numerical analysis of the downstream wind turbine blade is conducted. In particular, the interaction between the tower and the rotor passage is investigated. Circular cross sectional tower and aerofoil shapes are considered in a staggered configuration and under cross-stream motion. The resulting blade static pressure and aerodynamic forces are investigated at different incident wind angles and wind speeds. Comparison of the flow field results against the conventional upstream wind turbine is also conducted. The wind flow is considered to be transient, incompressible, viscous Navier-Stokes and turbulent. The k-ε model is utilized as the turbulence closure. The passage of the rotor blade is governed by ALE and is represented numerically as a sliding mesh against the upstream fixed tower domain. Both the blade and tower cross sections are padded with a boundary layer mesh to accurately capture the viscous forces while several levels of refinement were implemented throughout the domain to assess and avoid the mesh dependence.

Sign in / Sign up

Export Citation Format

Share Document