Empirical study on ultrasonic assisted turn-milling

2021 ◽  
pp. 095440892110087
Author(s):  
Saeid Amini ◽  
Mohammad Baraheni ◽  
Mohammad Khaki
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Ultrasonic Vibration ◽  
Feed Rate ◽  
Rotational Speed ◽  
Milling Process ◽  
Machining Process ◽  
Machining Parameters ◽  
Machining Processes ◽  
Turn Milling

Turn-milling process has been paid attention in order to be used in multi-task machining processes. Moreover, looking for new machining techniques aimed at reducing cutting force is of important. Reducing cutting force in machining processes has the benefits of extending tool life and improving surface quality. One of the new concepts for reducing the cutting force is applying ultrasonic vibration. In this paper, effects of ultrasonic vibration under different machining parameters in turn-milling process of Al-7075 alloy will be investigated. In this order, a special mechanism was designed to apply ultrasonic vibration during machining process. Ultrasonic vibration exertion on the tool reduced cutting force and surface roughness up to 75% and 35%, respectively. Also tool rotational speed increment induced cutting force and surface roughness increment. In addition, tool feed rate and workpiece rotational speed increment caused cutting force and surface roughness increment. Although, feed rate was more influential.

scholarly journals EFFECT OF MINIMUM QUANTITY LUBRICATION ON SURFACE ROUGHNESS IN TOOL-BASED MICROMILLING

2017 ◽  
Vol 18 (1) ◽  
pp. 147-154
Author(s):  
Mohammad Yeakub Ali ◽  
Wan Norsyazila Jailani ◽  
Mohamed Rahman ◽  
Muhammad Hasibul Hasan ◽  
Asfana Banu
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Spindle Speed ◽  
Machining Process ◽  
Depth Of Cut ◽  
Microfluidic Channels ◽  
Machining Parameters ◽  
Machining Processes ◽  
Dry Cutting ◽  
Minimum Quantity

Cutting fluid plays an important role in machining processes to achieve dimensional accuracy in reducing tool wear and improving the tool life. Conventional flood cooling method in machining processes is not cost effective and consumption of huge amount of cutting fluids is not healthy and environmental friendly. In micromachining, flood cooling is not recommended to avoid possible damage of the microstructures. Therefore, one of the alternatives to overcome the environmental issues to use minimum quantity of lubrication (MQL) in machining process. MQL is eco-friendly and has economical advantage on manufacturing cost. However, there observed lack of study on MQL in improving machined surface roughness in micromilling. Study of the effects of MQL on surface roughness should be carried out because surface roughness is one of the important issues in micromachined parts such as microfluidic channels. This paper investigates and compares surface roughness with the presence of MQL and dry cutting in micromilling of aluminium alloy 1100 using DT-110 milling machine. The relationship among depth of cut, feed rate, and spindle speed on surface roughness is also analyzed. All three machining parameters identified as significant for surface roughness with dry cutting which are depth of cut, feed rate, and spindle speed. For surface roughness with MQL, it is found that spindle speed did not give much influence on surface roughness. The presence of MQL provides a better surface roughness by decreasing the friction between tool and workpiece.

scholarly journals Theoretical and Experimental Investigation Into The Machining Performance in Axial Ultrasonic Vibration–Assisted Cutting of Ti6Al4V

2021 ◽  
Author(s):  
He Sui ◽  
Lifeng Zhang ◽  
Shuang Wang ◽  
Zhaojun Gu
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Influencing Factors ◽  
Ultrasonic Vibration ◽  
Tool Life ◽  
Feed Rate ◽  
Rotation Speed ◽  
Machining Parameters ◽  
Machining Performance ◽  
Cutting Depth

Abstract Axial ultrasonic vibration-assisted cutting (AUVC) has proved to have better machining performance compared with conventional cutting methods; however, the effect of numerous and complex influencing factors on machining performance has not been clearly revealed and a recommended combination of cutting conditions has not been proposed yet, especially for difficult-to-machine material such as Ti6Al4V alloy. This paper focuses on experimental and theoretical investigation into machining performance when cutting Ti6Al4V with the AUVC method. First, a retrospective of the separation characteristics of AUVC is provided and the variable parameter cutting characteristics are demonstrated. We classify the influencing factors on machining performance into four categories: machining parameters, vibration parameters, tool choice, and cooling conditions. The relationship between these factors in terms of their effect on machining performance is established theoretically. Then, it describes experiments to determine the influence of these factors on cutting force, tool life, and surface roughness. For absolute influence, the orders for cutting force, tool life, and surface roughness are respectively cutting depth > amplitude > feed rate > rotation speed, rotation speed > feed rate > amplitude > cutting depth, and feed rate > amplitude > cutting depth > rotation speed. However, for relative influence, the order is unified as: amplitude > feed rate > rotation speed > cutting depth. Finally, it suggests a smaller feed rate, larger amplitude, moderate rotation speed, and smaller cutting depth in addition to a WC tool coated with TiAlN and used under HPC cooling condition for optimal performance of AUVC. This recommendation is based on the theoretical analysis and experimental results of cutting force, surface roughness, and tool life.

scholarly journals Effects of Parameters of Machining on Cutting Force and Roughness when Machining AZ31 Magnesium Alloy

2019 ◽  
Vol 9 (2) ◽  
pp. 4756-4758
Keyword(s):  
Cutting Force ◽  
Feed Rate ◽  
High Speed ◽  
Cutting Speed ◽  
Minimum Quantity Lubrication ◽  
Cutting Parameters ◽  
Machining Process ◽  
Mg Alloy ◽  
Machining Parameters ◽  
Machining Processes

This project was done to learn the effects of cutting parameters on cutting force and roughness (surface roughnes) of AZ31 magnesium (Mg) alloy. Machining parameters involved in this project are cutting speed, feed rate, and lubrication methods. Deckel Maho DMU 50 eVolution high speed milling machine was using and uncoated carbide button insert was used as the cutting tool. Cutting force was measured during the milling process and roughness was measured after that and cleaning process to ensure no interference that would conflicted the results. The best machining parameters identified when feed rate at 0.05 mm per tooth, cutting speed are at 600 m per min, and minimum quantity lubrication was applied during the machining process. From analysis of variance (ANOVA) table generated by Minitab software, this project can conclude that feed rate, cutting speed, and lubrication methods are significant to cutting force and roughness when machining AZ31 Mg Alloy Therefore, the relationship of surface roughness and cutting force should be taken as a major key point in machining processes. In the automotive field, magnesium was used to fabricate an engine that place at front body due to reduce the weight of vehicle. This design can increase performance and balancing of weight [1].

Evaluation of Surface Roughness and Cutting Forces During Precision Turning

2012 ◽  
Vol 622-623 ◽  
pp. 390-393 ◽  
Author(s):  
R. Vinayagamoorthy ◽  
M. Anthony Xavior
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Working Conditions ◽  
Cutting Speed ◽  
Machining Process ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Medical Implants ◽  
Machining Processes ◽  
Precision Turning

The Ti-6Al-4V titanium alloy is commonly used in aerospace, automotive industries and for manufacturing of medical implants, due to its biocompatibility. The objective of this work is to investigate the performance of precision turning using conventional lathe on Ti6Al4V under dry working conditions. A range of parameters that involve the machining processes were recognized and a consensus was reached to finalize its values. The proposed work is to carry out machining under the selected levels of parameters to evaluate the cutting force and surface roughness generated as the consequence of the machining process. Cutting speed, feed rate, depth of cut and nose radiuses are considered as the machining parameters for experimentation. The variation in the surface roughness and the cutting force for the variation of each machining parameters are presented graphically.

Optimization of turn-milling process in roughing and finishing regimes: Trade-off between productivity, cutting force and surface integrity

2021 ◽  
pp. 095440892199851
Author(s):  
Ebrahim Hosseini ◽  
Shafiqur Rehman ◽  
Ashkan Alimoradi
Keyword(s):  
Cutting Force ◽  
Desirability Function ◽  
Milling Process ◽  
Machining Process ◽  
Hybrid Machining ◽  
Trade Off ◽  
Hybrid Machining Process ◽  
Process Factors ◽  
Turn Milling ◽  
Selection Of

Turn-milling is a hybrid machining process which used benefits of interrupted cutting for proceeding of round bars. However, number of controllable parameters in the hybrid process is numerous that makes optimizing the process complicated. In the present study, an optimization work has been proposed to investigate the trade-off between production rate and cutting force in roughing regime as well surface roughness and tensile residual stress in finishing regime. Number of 43 experiments based on response surface methodology was designed and carried out to gather required data for development of quadratic empirical models. Then, the adequacy and importance of process factors were analyzed using analysis of variances. Finally, desirability function was used to optimize the process in rough and finish machining regimes. The obtained results showed that selection of eccentricity and cutter speed at their maximum working range can effectively enhance the quality characteristics in both the roughing and finishing regimes.

scholarly journals Influence of Ultrasonic Vibration-Assisted Ball-End Milling on the Cutting Performance of AZ31B Magnesium Alloy

2020 ◽  
Vol 9 (4) ◽  
pp. 271-276
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Ultrasonic Vibration ◽  
Biomedical Applications ◽  
End Milling ◽  
Cutting Temperature ◽  
Cutting Performance ◽  
Machining Process ◽  
Dry Conditions ◽  
Good Biocompatibility

Magnesium alloys have a tremendous possibility for biomedical applications due to their good biocompatibility, integrity and degradability, but their low ignition temperature and easy corrosive property restrict the machining process for potential biomedical applications. In this research, ultrasonic vibration-assisted ball milling (UVABM) for AZ31B is investigated to improve the cutting performance and get specific surface morphology in dry conditions. Cutting force and cutting temperatures are measured during UVABM. Surface roughness is measured with a white light interferometer after UVABM. The experimental results show cutting force and cutting temperature reduce due to ultrasonic vibration, and surface roughness decreases by 34.92%, compared with that got from traditional milling, which indicates UVABM is suitable to process AZ31B for potential biomedical applications.

scholarly journals Research and Optimization of Surface Roughness in Milling of SLM Semi-Finished Parts Manufactured by Using the Different Laser Scanning Speed

Materials ◽  
2019 ◽  
Vol 13 (1) ◽  
pp. 9 ◽  
Author(s):  
Andrzej Matras
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Laser Scanning ◽  
Cutting Tool ◽  
Scanning Speed ◽  
Milling Process ◽  
Face Milling ◽  
Machining Parameters ◽  
The Face ◽  
Laser Scanning Speed

The paper studies the potential to improve the surface roughness in parts manufactured in the Selective Laser Melting (SLM) process by using additional milling. The studied process was machining of samples made of the AlSi10Mg alloy powder. The simultaneous impacts of the laser scanning speed of the SLM process and the machining parameters of the milling process (such as the feed rate and milling width) on the surface roughness were analyzed. A mathematical model was created as a basis for optimizing the parameters of the studied processes and for selecting the sets of optimum solutions. As a result of the research, surface with low roughness (Ra = 0.14 μm, Rz = 1.1 μm) was obtained after the face milling. The performed milling allowed to reduce more than 20-fold the roughness of the SLM sample surfaces. The feed rate and the cutting width increase resulted in the surface roughness deterioration. Some milled surfaces were damaged by the chip adjoining to the rake face of the cutting tool back tooth.

Optimization of Process Parameters for Cutting Force for Aluminium 7010 in CNC End Milling Process

2018 ◽  
Vol 10 (6) ◽  
Author(s):  
M. Kishanth ◽  
P. Rajkamal ◽  
D. Karthikeyan ◽  
K. Anand
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Process Parameters ◽  
End Milling ◽  
Milling Process ◽  
Machining Process ◽  
Depth Of Cut ◽  
Optimization Of Process Parameters ◽  
Cnc End Milling ◽  
End Milling Process

In this paper CNC end milling process have been optimized in cutting force and surface roughness based on the three process parameters (i.e.) speed, feed rate and depth of cut. Since the end milling process is used for abrading the wear caused is very high, in order to reduce the wear caused by high cutting force and to decrease the surface roughness, the optimization is much needed for this process. Especially for materials like aluminium 7010, this kind of study is important for further improvement in machining process and also it will improve the stability of the machine.

Taguchi Method Based Experiments of Titanium TC11 Flank Milling Parameters

2009 ◽  
Vol 407-408 ◽  
pp. 608-611 ◽  
Author(s):  
Chang Yi Liu ◽  
Cheng Long Chu ◽  
Wen Hui Zhou ◽  
Jun Jie Yi
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Feed Rate ◽  
High Speed ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Flank Milling ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Mill Machining

Taguchi design methodology is applied to experiments of flank mill machining parameters of titanium alloy TC11 (Ti6.5A13.5Mo2Zr0.35Si) in conventional and high speed regimes. This study includes three factors, cutting speed, feed rate and depth of cut, about two types of tools. Experimental runs are conducted using an orthogonal array of L9(33), with measurement of cutting force, cutting temperature and surface roughness. The analysis of result shows that the factors combination for good surface roughness, low cutting temperature and low resultant cutting force are high cutting speed, low feed rate and low depth of cut.

Optimization Method of Rotational Axis Motion in 5-Axis Controlled Machining to Keep Command Tool Feed Rate

2020 ◽  
Author(s):  
Takayuki Nakamura ◽  
Kohei Ichikawa ◽  
Masanobu Hasegawa ◽  
Jun'ichi Kaneko ◽  
Takeyuki Abe
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Machining Process ◽  
Rotational Axis ◽  
Feed Speed ◽  
Machining Processes ◽  
Machining Time ◽  
Machined Surface ◽  
Lead Angle ◽  
Tool Posture

Abstract In recent machining processes, 5-axis controlled machine tool is widely used for machining complicated workpiece shape with curved surface. In such process, to achieve high productivity, planning method of cutting conditions to satisfy both following the commanded tool feed rate in machining process and realization of good surface roughness are required. In conventional study, it is known that lead angle of tool posture against local machined surface influence the surface roughness. Then, common commercial CAM systems have already functioned to avoid interference and control the lead angle in each cutter location. However, in the generated cutter locations by the conventional algorithms, when the tool posture changes rapidly, there is a problem that actual feed rate does not reach the command value and machining time becomes longer than expected. In this paper, we propose the new tool posture correction algorithm. In the proposed method, first, the rotational axis that causes the feed speed rate decline is specified by preliminary experiments. And, the jerk value that is the threshold for the feed speed decline is investigated. After that, for the NC program, the command value of the target axis is modified within a range where interference of cutting tool does not occur, thereby preventing a decline in the actual feed rate. This paper describes an outline of the proposed modification method and the effect of the modification of the target axis positions on the lead angle and the actual feed rate.

Sign in / Sign up

Export Citation Format

Share Document