scholarly journals Influence of Mercerization on Micro-structure and Properties of Kapok Blended Yarns with Different Blending Ratios

2011 ◽  
Vol 6 (3) ◽  
pp. 155892501100600 ◽  
Author(s):  
Jie Liu ◽  
Fumei Wang
Keyword(s):  
Alkali Treatment ◽  
Chemical Compositions ◽  
X Ray Diffraction ◽  
Cellulose I ◽  
Micro Structure ◽  
Obvious Effect ◽  
Kapok Fiber ◽  
X Ray ◽  
Before And After ◽  
Mercerization Treatment

To investigate the effect of mercerization on micro-structure and the properties of kapok/cotton blended yarns. FTIR spectra and x-ray diffraction (XRD) results, moisture regains and mechanical properties of blended yarns were compared before and after mercerization. The results show that mercerization treatment did not have an obvious effect on chemical compositions of cellulose, but did lead to decreasing on crystallinity of blended yarns, and transformed certain portion of cellulose I into cellulose II. When the NaOH concentration increased from 180g/L to 250 g/L, the strengths of blended yarns increased and elongations at breaking declined, and the extent of changes were lessened gradually with the increase of kapok fiber content, when the NaOH concentration further reached 280g/L, the strengths of blended yarns with high content of kapok fiber dropped dramatically, and elongations at breaking increased gradually, while hygroscopicities of blended yarns increased significantly. Different from cotton fiber, a more moderate alkali treatment condition should be chosen in mercerization process for kapok fiber.

scholarly journals Preparation and Characteristics of Wet-Spun Filament Made of Cellulose Nanofibrils with Different Chemical Compositions

Polymers ◽  
2020 ◽  
Vol 12 (4) ◽  
pp. 949 ◽  
Author(s):  
Chan-Woo Park ◽  
Ji-Soo Park ◽  
Song-Yi Han ◽  
Eun-Ah Lee ◽  
Gu-Joong Kwon ◽  
...  
Keyword(s):  
High Pressure ◽  
Tensile Strength ◽  
Cellulose Nanofibrils ◽  
Chemical Compositions ◽  
High Pressure Homogenization ◽  
Cellulose Nanofibril ◽  
X Ray Diffraction ◽  
Cellulose I ◽  
Filtration Time ◽  
X Ray

In this study, wet-spun filaments were prepared using lignocellulose nanofibril (LCNF), with 6.0% and 13.0% of hemicellulose and lignin, respectively, holocellulose nanofibril (HCNF), with 37% hemicellulose, and nearly purified-cellulose nanofibril (NP-CNF) through wet-disk milling followed by high-pressure homogenization. The diameter was observed to increase in the order of NP-CNF ≤ HCNF < LCNF. The removal of lignin improved the defibrillation efficiency, thus increasing the specific surface area and filtration time. All samples showed the typical X-ray diffraction pattern of cellulose I. The orientation of CNFs in the wet-spun filaments was observed to increase at a low concentration of CNF suspensions and high spinning rate. The increase in the CNF orientation improved the tensile strength and elastic modulus of the wet-spun filaments. The tensile strength of the wet-spun filaments decreased in the order of HCNF > NP-CNF > LCNF.

scholarly journals Spectroscopic studies of kaolin from different Brazilian regions

Clay Minerals ◽  
2008 ◽  
Vol 43 (1) ◽  
pp. 129-135 ◽  
Author(s):  
R. B. Scorzelli ◽  
L. C. Bertolino ◽  
A. B. Luz ◽  
M. Duttine ◽  
F. A. N. G. Silva ◽  
...  
Keyword(s):  
Paper Industry ◽  
Spectroscopic Studies ◽  
Chemical Compositions ◽  
X Ray Diffraction ◽  
X Ray ◽  
Chemical Treatments ◽  
Fe Oxides ◽  
Spin Resonance ◽  
Before And After ◽  
Mineralogical Phase

AbstractOver the past several decades, kaolin has been used intensively in the paper industry as a coating and filler material. These applications require kaolin of a high brightness grade, which depends heavily on the level of impurities (mainly Fe-bearing minerals such as Fe oxides and hydroxides) and may be improved by beneficiation processes involving grain-size classification, magnetic separation and chemical treatments. This investigation was carried out on five Brazilian kaolin samples of different geographical and geological origins. Granulometric, mineralogical, chemical and physical characterizations were performed on all samples before and after the beneficiation process.Chemical compositions were determined by X-ray fluorescence and the most important crystalline phases were identified using X-ray diffraction. Kaolinite is the dominant mineralogical phase with minor amounts of muscovite and quartz. The nature of Fe impurities was investigated by electron spin resonance and 57Fe Mössbauer spectroscopy. For all studied kaolin samples, Fe ions (Fe3+ and Fe2+) are present in variable amounts, in the kaolinite structure and also in Fe oxides (magnetite, hematite and goethite). The beneficiation procedure aims to remove these Fe oxides and was found to be most efficient for the Mogi das Cruzes kaolin. The Seridó kaolin had the best whiteness index observed among the analysed samples.

Evaluation of Freezing Methods by Low Temperature X-Ray Diffraction

1977 ◽  
Vol 35 ◽  
pp. 330-333
Author(s):  
T. Gulik-Krzywicki ◽  
M.J. Costello
Keyword(s):  
Biological Materials ◽  
Molecular Organization ◽  
X Ray Diffraction ◽  
Glass Capillary ◽  
X Ray ◽  
Rate Dependent ◽  
Before And After ◽  
Freeze Etching ◽  
Diffraction Patterns ◽  
Set Up

Freeze-etching electron microscopy is currently one of the best methods for studying molecular organization of biological materials. Its application, however, is still limited by our imprecise knowledge about the perturbations of the original organization which may occur during quenching and fracturing of the samples and during the replication of fractured surfaces. Although it is well known that the preservation of the molecular organization of biological materials is critically dependent on the rate of freezing of the samples, little information is presently available concerning the nature and the extent of freezing-rate dependent perturbations of the original organizations. In order to obtain this information, we have developed a method based on the comparison of x-ray diffraction patterns of samples before and after freezing, prior to fracturing and replication.Our experimental set-up is shown in Fig. 1. The sample to be quenched is placed on its holder which is then mounted on a small metal holder (O) fixed on a glass capillary (p), whose position is controlled by a micromanipulator.

A New Polyethylene Corrosion Protecting Coating with Ion Selectivity

2011 ◽  
Vol 314-316 ◽  
pp. 273-278
Author(s):  
Yu Hua Dong ◽  
Ke Ren ◽  
Qiong Zhou
Keyword(s):  
Ion Selectivity ◽  
Nano Particles ◽  
Ammonium Bromide ◽  
Linear Low Density Polyethylene ◽  
X Ray Diffraction ◽  
Sulfosalicylic Acid ◽  
X Ray ◽  
Chemically Modified ◽  
Before And After ◽  
Industrial Standards

Linear low density polyethylene (LLDPE) was chemically modified with grafting maleic anhydride (MAH) monomer on its backbone by melting blending. Nano-particles SiO2 was modified by cationic surfactant hexadecyl trimethyl ammonium bromide (CTAB) and anionic surfactant sulfosalicylic acid (SSA) and added to PE coating respectively. Measurement of membrane potential showed that the coating containing modified SiO2 nano-particles had characteristic of ion selectivity. The properties of the different coatings were investigated according to relative industrial standards. Experimental results indicated that PE coating with ion selectivity had better performances, such as adhesion strength, cathodic disbonding and anti-corrosion, than those of coating without ion selectivity. Crystal structure of the coatings before and after alkali corrosion was characterized by Fourier transform infrared spectra (FTIR) and X-ray diffraction (XRD). Structure of the coating without ion selectivity was damaged by NaOH alkali solution, causing mechanical properties being decreased. And the structure of the ion selective coatings was not affected.

scholarly journals New Insights into the Crystal Chemistry of Elpidite, Na2Zr[Si6O15]·3H2O and (Na1+YCax□1−X−Y)Σ=2Zr[Si6O15]·(3−X)H2O, and Ab Initio Modeling of IR Spectra

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2160
Author(s):  
Alexander Bogdanov ◽  
Ekaterina Kaneva ◽  
Roman Shendrik
Keyword(s):  
Ir Spectra ◽  
Structural Models ◽  
Chemical Characterization ◽  
Chemical Compositions ◽  
X Ray Diffraction ◽  
Special Group ◽  
X Ray ◽  
Influence Of Water ◽  
Radioactive Species

Elpidite belongs to a special group of microporous zirconosilicates, which are of great interest due to their capability to uptake various molecules and ions, e.g., some radioactive species, in their structural voids. The results of a combined electron probe microanalysis and single-crystal X-ray diffraction study of the crystals of elpidite from Burpala (Russia) and Khan-Bogdo (Mongolia) deposits are reported. Some differences in the chemical compositions are observed and substitution at several structural positions within the structure of the compounds are noted. Based on the obtained results, a detailed crystal–chemical characterization of the elpidites under study was carried out. Three different structure models of elpidite were simulated: Na2ZrSi6O15·3H2O (related to the structure of Russian elpidite), partly Ca-replaced Na1.5Ca0.25ZrSi6O15·2.75H2O (close to elpidite from Mongolia), and a hypothetical CaZrSi6O15·2H2O. The vibration spectra of the models were obtained and compared with the experimental one, taken from the literature. The strong influence of water molecule vibrations on the shape of IR spectra of studied structural models of elpidite is discussed in the paper.

Sedimentary Clays as Geopolymer Precursor

2018 ◽  
Vol 39 ◽  
pp. 97-111
Author(s):  
F. Mostefa ◽  
Nasr Eddine Bouhamou ◽  
H.A. Mesbah ◽  
Salima Aggoun ◽  
D. Mekhatria
Keyword(s):  
Sodium Hydroxide ◽  
Mineralogical Composition ◽  
Cementitious Materials ◽  
Raw Material ◽  
X Ray Diffraction ◽  
Calcination Time ◽  
Calorimetric Analysis ◽  
X Ray ◽  
Before And After ◽  
Mechanical Performances

This work aims to study the feasibility of making a geopolymer cement based on dredged sediments, from the Fergoug dam (Algeria) and to evaluate their construction potential particularly interesting in the field of special cementitious materials. These sediments due to their mineralogical composition as aluminosilicates; are materials that can be used after heat treatment. Sedimentary clays were characterized before and after calcination by X-ray diffraction, ATG / ATD, spectroscopy (FTIR) and XRF analysis. The calcination was carried out on the raw material sieved at 80 μm for a temperature of 750 ° C, for 3.4 and 5 hours. The reactivity of the calcined products was measured using isothermal calorimetric analysis (DSC) on pastes prepared by mixing an alkaline solution of sodium hydroxide (NaOH) 8 M in an amount allowing to have a Na / Al ratio close to 1 (1: 1). Also, cubic mortar samples were prepared with a ratio L / S: 0.8, sealed and cured for 24 hours at 60 ° C and then at room temperature until the day they were submited to mechanical testing. to check the extent of geopolymerization. The results obtained allowed to optimize the calcination time of 5 hours for a better reactivity of these sediments, and a concentration of 8M of sodium hydroxide and more suitable to have the best mechanical performances.

Aging of iron manganite negative temperature coefficient thermistors

1998 ◽  
Vol 13 (5) ◽  
pp. 1238-1242 ◽  
Author(s):  
T. Battault ◽  
R. Legros ◽  
A. Rousset
Keyword(s):  
Temperature Coefficient ◽  
Spinel Structure ◽  
Negative Temperature Coefficient ◽  
Negative Temperature ◽  
X Ray Diffraction ◽  
X Ray ◽  
Octahedral Sites ◽  
Before And After ◽  
Structural Equilibrium ◽  
Electrical Data

“Aging,” defined as the drift of resistance with temperature after 1000 h, was investigated for iron manganite temperature coefficient thermistors. For these devices, aging is relatively large, about 10%. The cationic distributions before and after aging were determined by Mössbauer spectroscopy. These distributions explain all the x-ray diffraction and correlated electrical data. The origin of the aging observed on iron manganites thermistors has been identified. It is due to the migration of Fe3+ ions from tetrahedral to octahedral sites of the spinel structure in order to reach a structural equilibrium.

Oxidation of Alloy-X in Subcritical, Transition, and Supercritical Water

CORROSION ◽  
10.5006/3881 ◽  
2021 ◽  
Author(s):  
Zachary Karmiol ◽  
Dev Chidambaram
Keyword(s):  
Supercritical Water ◽  
Photoelectron Spectroscopy ◽  
Focused Ion Beam ◽  
Elevated Temperatures ◽  
Subcritical Water ◽  
Ion Beam ◽  
X Ray Diffraction ◽  
X Ray ◽  
Nickel Based Superalloy ◽  
Before And After

This work investigates the oxidation of a nickel based superalloy, namely Alloy X, in water at elevated temperatures: subcritical water at 261°C and 27 MPa, the transition between subcritical and supercritical water at 374°C and 27 MPa, and supercritical water at 380°C and 27 MPa for 100 hours. The morphology of the sample surfaces were studied using scanning electron microscopy coupled with focused ion beam milling, and the surface chemistry was investigated using X-ray diffraction, Raman spectroscopy, energy dispersive X-ray spectroscopy, and X-ray photoelectron spectroscopy before and after exposure studies. Surfaces of all samples were identified to comprise of a ferrite spinel containing aluminum.

Twin memory and twin amnesia in anorthoclase

2000 ◽  
Vol 64 (2) ◽  
pp. 195-200 ◽  
Author(s):  
S. A. Hayward ◽  
E. K. H. Salje
Keyword(s):  
Phase Transitions ◽  
Transition Temperature ◽  
Alkali Feldspar ◽  
Spatial Distributions ◽  
X Ray Diffraction ◽  
Alkali Cations ◽  
X Ray ◽  
Natural Minerals ◽  
Synthetic Materials ◽  
Before And After

AbstractMany natural minerals and synthetic materials display twin microstructures resulting from displacive phase transitions. These microstructures may be removed temporarily from the sample by heating above the relevant transition temperature, though the twinning generally returns on subsequent cooling.In anorthoclase, the spatial distributions of twins before and after brief annealing above TC are often identical. This property appears to be a common feature in many materials which undergo ferroelastic phase transitions, and is known as ‘twin memory’. The atomic mechanisms responsible for this twin memory may be investigated by studying the annealing regimes required to remove the memory effect; how long must a sample be annealed, and at what temperature, to induce ‘twin amnesia’.High-resolution X-ray diffraction (XRD) has been used to investigate twin memory and twin amnesia in anorthoclase. In anorthoclase, the primary constraint on twin amnesia is thermodynamic, rather than kinetic. The critical temperature to induce amnesia correlates well with the top of the (Na, K) solvus in disordered alkali feldspar. For this reason, the proposed mechanism for twin memory involves the segregation of alkali cations in thin lamellae at the twin boundaries.

Sign in / Sign up

Export Citation Format

Share Document