scholarly journals Establishment of High-Accuracy and High-Efficiency Machining Method for Scroll-Shape Workpiece with End Mill. 1st Report. Proposal of High-Accuracy and High-Efficiency Machining Methods Based on Maximum Chip Area and Surface Roughness.

1995 ◽  
Vol 61 (583) ◽  
pp. 1184-1191 ◽  
Author(s):  
Hiroyasu Iwabe ◽  
Tomoharu Shimada
Keyword(s):  
Surface Roughness ◽  
High Efficiency ◽  
High Accuracy ◽  
End Mill ◽  
Chip Area

scholarly journals High-Efficiency Milling of Steam Turbine Blade

2016 ◽  
Vol 10 (6) ◽  
pp. 993-999 ◽  
Author(s):  
Xin Yuan ◽  
◽  
Takanori Yazawa ◽  
Hideo Ito ◽  
Tatsuki Otsubo ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Steam Turbine ◽  
Turbine Blade ◽  
High Efficiency ◽  
Small Diameter ◽  
Surface Profile ◽  
End Mill ◽  
End Mills ◽  
Steam Turbine Blade

Conventional methods often use ball end mills with a small diameter to finish machining of a steam turbine blade to satisfy accuracy requirements by using a small pick feed value. Thus, the cutting length increases, resulting in increased wear and a lower milling efficiency. Therefore, a new method using a tilt-taper end mill is proposed. This paper presents the validity of the proposed method used for milling planes by comparing the ball and square end mills through tool wear experiments. Factors including removal degree, surface roughness, tool wear, and machined surfaces are investigated with respect to the plane model. The experimental results show that tilt end mill can retard the tool wear remarkably to obtain a steady surface profile, and the maximum surface roughness value, using the tilt-taper end mill, is less than 6μm until process completion.

scholarly journals Investigation of Multiparameter Laser Stripping of AlTiN and DLC C Coatings

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 951
Author(s):  
Tomáš Primus ◽  
Josef Hlavinka ◽  
Pavel Zeman ◽  
Jan Brajer ◽  
Martin Šorm ◽  
...  
Keyword(s):  
Surface Roughness ◽  
High Efficiency ◽  
Steel Substrate ◽  
Cutting Tools ◽  
High Hardness ◽  
Working Time ◽  
Nanosecond Laser ◽  
Altin Coating ◽  
Successful Removal ◽  
Frequency Laser

The lifetime and properties of cutting tools and forming moulds can be prolonged and enhanced by the deposition of hard, thin coatings. After a certain period of usage, the coating will deteriorate. Any remaining coating must be removed prior to successful recoating. Laser stripping is a fast and environmentally friendly coating removal method. In this paper, we present laser removal of two types of coatings deposited on a 1.2379 tool steel substrate, namely, an AlTiN coating with high hardness and a DLC C coating with a small coefficient of friction (COF). A powerful nanosecond laser was employed to remove the coating from the substrate with high efficiency, along with suitable residual surface roughness. Measurements were taken of surface roughness, removed depth, and working time on a stripped area of 1 cm2. The samples were evaluated under a microscope, with a 3D profilometer, and by EDS chemical analysis. Successful removal of the coating was confirmed by optical analysis, but detailed chemical characterisation showed that about 30% of the coating element may remain on the surface. Moreover, a working time of less than 7.5 s per cm2 was obtained in this study. In addition, it was shown that the application of a second low energy, high frequency laser beam pass leads to remelting of the peaks of the material and reduced surface roughness.

scholarly journals Experimental Investigation and Comparison of the Thermal Performance of Additively and Conventionally Manufactured Heat Exchangers

Metals ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 574
Author(s):  
Ana Vafadar ◽  
Ferdinando Guzzomi ◽  
Kevin Hayward
Keyword(s):  
Surface Roughness ◽  
Thermal Performance ◽  
Heat Exchangers ◽  
High Efficiency ◽  
Cooling System ◽  
Fluid Dynamic ◽  
Dynamic Performance ◽  
Experimental Studies ◽  
Manufacturing Method ◽  
Industrial Sectors

Air heat exchangers (HXs) are applicable in many industrial sectors because they offer a simple, reliable, and cost-effective cooling system. Additive manufacturing (AM) systems have significant potential in the construction of high-efficiency, lightweight HXs; however, HXs still mainly rely on conventional manufacturing (CM) systems such as milling, and brazing. This is due to the fact that little is known regarding the effects of AM on the performance of AM fabricated HXs. In this research, three air HXs comprising of a single fin fabricated from stainless steel 316 L using AM and CM methods—i.e., the HXs were fabricated by both direct metal printing and milling. To evaluate the fabricated HXs, microstructure images of the HXs were investigated, and the surface roughness of the samples was measured. Furthermore, an experimental test rig was designed and manufactured to conduct the experimental studies, and the thermal performance was investigated using four characteristics: heat transfer coefficient, Nusselt number, thermal fluid dynamic performance, and friction factor. The results showed that the manufacturing method has a considerable effect on the HX thermal performance. Furthermore, the surface roughness and distribution, and quantity of internal voids, which might be created during and after the printing process, affect the performance of HXs.

scholarly journals Effect of Optical and Morphological Control of Single-Structured LEC Device

Micromachines ◽  
2021 ◽  
Vol 12 (7) ◽  
pp. 843
Author(s):  
Woo Jin Jeong ◽  
Jong Ik Lee ◽  
Hee Jung Kwak ◽  
Jae Min Jeon ◽  
Dong Yeol Shin ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Surface Roughness ◽  
Surface Properties ◽  
High Efficiency ◽  
High Surface ◽  
Reduction Rate ◽  
Operating Characteristics ◽  
Emission Layer ◽  
Light Emitting ◽  
Stable Operating

We investigated the performance of single-structured light-emitting electrochemical cell (LEC) devices with Ru(bpy)3(PF6)2 polymer composite as an emission layer by controlling thickness and heat treatment. When the thickness was smaller than 120–150 nm, the device performance decreased because of the low optical properties and non-dense surface properties. On the other hand, when the thickness was over than 150 nm, the device had too high surface roughness, resulting in high-efficiency roll-off and poor device stability. With 150 nm thickness, the absorbance increased, and the surface roughness was low and dense, resulting in increased device characteristics and better stability. The heat treatment effect further improved the surface properties, thus improving the device characteristics. In particular, the external quantum efficiency (EQE) reduction rate was shallow at 100 °C, which indicates that the LEC device has stable operating characteristics. The LEC device exhibited a maximum luminance of 3532 cd/m2 and an EQE of 1.14% under 150 nm thickness and 100 °C heat treatment.

scholarly journals High-Accuracy Surface Topography Manufacturing for Continuous Phase Plates Using an Atmospheric Pressure Plasma Jet

Micromachines ◽  
2021 ◽  
Vol 12 (6) ◽  
pp. 683
Author(s):  
Huiliang Jin ◽  
Caixue Tang ◽  
Haibo Li ◽  
Yuanhang Zhang ◽  
Yaguo Li
Keyword(s):  
Surface Topography ◽  
Atmospheric Pressure ◽  
High Efficiency ◽  
Atmospheric Pressure Plasma ◽  
Plasma Jet ◽  
Continuous Phase ◽  
High Accuracy ◽  
Phase Plate ◽  
Atmospheric Pressure Plasma Jet ◽  
Pressure Plasma

The continuous phase plate (CPP) is the vital diffractive optical element involved in laser beam shaping and smoothing in high-power laser systems. The high gradients, small spatial periods, and complex features make it difficult to achieve high accuracy when manufacturing such systems. A high-accuracy and high-efficiency surface topography manufacturing method for CPP is presented in this paper. The atmospheric pressure plasma jet (APPJ) system is presented and the removal characteristics are studied to obtain the optimal processing parameters. An optimized iterative algorithm based on the dwell point matrix and a fast Fourier transform (FFT) is proposed to improve the accuracy and efficiency in the dwell time calculation process. A 120 mm × 120 mm CPP surface topography with a 1326.2 nm peak-to-valley (PV) value is fabricated with four iteration steps after approximately 1.6 h of plasma processing. The residual figure error between the prescribed surface topography and plasma-processed surface topography is 28.08 nm root mean square (RMS). The far-field distribution characteristic of the plasma-fabricated surface is analyzed, for which the energy radius deviation is 11 μm at 90% encircled energy. The experimental results demonstrates the potential of the APPJ approach for the manufacturing of complex surface topographies.

Contour Extraction of Cerebrovascular Based on Maximum Optimization Cost

2011 ◽  
Vol 204-210 ◽  
pp. 1415-1418
Author(s):  
De Jiang Zhang ◽  
Na Na Dong ◽  
Xiao Mei Lin
Keyword(s):  
Dynamic Programming ◽  
Blood Vessel ◽  
High Efficiency ◽  
High Accuracy ◽  
Differential Method ◽  
Cost Curve ◽  
Contour Extraction ◽  
Target Image ◽  
The Cost ◽  
Conventional Algorithm

By studying the conventional algorithm of contour extraction, a new method of contour extraction in blood vessel of brain is proposed based on the MOC maximum optimization cost. First of all, the theory computes the gray differential of the image by conventional differential method to build the cost space. Then, by using dynamic programming theory, the maximum optimization cost curve in the space is extracted to serve as the specific cerebrovascular profile. The experiments show that this method ensures high efficiency in extracting cerebrovascular contour and a high accuracy in positioning cerebrovascular contour, and it diminishes the target image ambiguity caused by noise to improve the anti-interference ability of Contour extraction.

Surface Roughness Analysis for Radius End Mill in Cross Feed Direction Both Contour and Scanning Line Machinings

2020 ◽  
Author(s):  
Hirohisa Narita
Keyword(s):  
Surface Roughness ◽  
Inclination Angle ◽  
End Milling ◽  
Contour Line ◽  
End Mill ◽  
Good Surface ◽  
Corner Radius ◽  
Feed Direction ◽  
Scanning Line ◽  
Influence Degree

Abstract An optimum experimental condition, which realize good surface roughness in cross direction both contour and scanning lines, for radius end mill against some inclined surfaces is obtained and some features is these cutting processes is discussed in this paper. The optimum experimental condition, which consists of cutting type (or feed direction), spindle speed, feed rate, depth of immersion, inclination angle, corner radius of end mill and cross feed, is obtained and the influence degree of these parameters is calculated by using Taguchi method. The experiment is carried out based on L18 orthogonal array. Based on the influence degree and geometric contact status due to unique shape of radius end mill, some feature of radius end milling is introduced. As a result of the contour line machining, a scallop height is very influenced by the inclination angle and the corner radius, and surface machined by bottom edge must not be remained. Regarding the scanning line machining, “go-up” is good for the feed direction. Big corner radius is also suitable because side edge does not contact to workpiece. In other words, the cutting force in radial direction becomes small. Furthermore, the surface roughness of the scanning line machining is smaller than the one of the contour line machining.

Development of the cBN Electroplated End-Mill for High Precision Machining of CFRP

2020 ◽  
Author(s):  
Shinnosuke Yamashita ◽  
Tatsuya Furuki ◽  
Hiroyuki Kousaka ◽  
Toshiki Hirogaki ◽  
Eiichi Aoyama ◽  
...  
Keyword(s):  
Surface Roughness ◽  
End Milling ◽  
Drop Out ◽  
End Mill ◽  
Machined Surface ◽  
Side Milling ◽  
Reinforced Plastics ◽  
Milled Surface ◽  
Grinding Conditions ◽  
Grinding Tool

Abstract Recently, the demand of carbon fiber reinforced plastics (CFRP) has been rapidly increased in various fields. In most cases, CFRP products requires a finish machining like cutting or grinding. In the case of an end-milling, burrs and uncut fibers are easy to occur. On the other hand, a precise machined surface and edge will be able to obtain by using the grinding tool. Therefore, this research has been developed a novel the cBN electroplated end-mill that combined end-mill and grinding tool. In this report, the effectiveness of developed tool was investigated. First, the developed tool cut the CFRP with side milling. As the result, the cBN abrasives that were fixed on the outer surface of developed tool did not drop out. Next, the end-milled surface of CFRP was ground with the developed tool under several grinding conditions based on the Design of Experiment. Consequently, the optimum grinding condition that can obtain the sharp edge which does not have burrs and uncut fibers was found. However, surface roughness was not good enough. Thus, an oscillating grinding was applied. In addition, the theoretical surface roughness formula in case using the developed tool was formularized. As the result, the required surface roughness in the airplane field was obtained.

Dependence of LPBF Surface Roughness on Laser Incidence Angle and Component Build Orientation

2021 ◽  
Author(s):  
Ramesh Subramanian ◽  
David Rule ◽  
Onur Nazik
Keyword(s):  
Surface Roughness ◽  
Gas Turbine ◽  
High Efficiency ◽  
Surface Defects ◽  
Incidence Angle ◽  
Turbine Component ◽  
Potential Applicability ◽  
Process Qualification ◽  
Process Signature ◽  
Manufacturing Technologies

Abstract Laser Powder Bed Fusion (LPBF) of metallic components is unlocking new design options for high efficiency gas turbine component designs not possible by conventional manufacturing technologies. Surface roughness is a key characteristic of LPBF components that impacts heat transfer correlations and crack initiation from co-located surface defects — both are critical for gas turbine component durability and performance. However, even for a single material, there is an increasing diversity in laser machines (single vs multi-laser), layer thicknesses (∼20–80 microns) and orientations to the build plate (upskin, vertical and downskin) that result in significant variability in surface roughness. This study systematically compares the surface roughness across the above-mentioned variables to further develop a repeatable correlation of surface roughness to the angle between the substrate normal and laser incidence direction. This presented data will be discussed in detail, to show potential applicability of this process signature curve across materials, machines, and substrate orientations. Future steps to a rapid process qualification standard for surface roughness, across Siemens Energy’s global manufacturing footprint will also be discussed.

Sign in / Sign up

Export Citation Format

Share Document