scholarly journals Investigation of Multiparameter Laser Stripping of AlTiN and DLC C Coatings

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 951
Author(s):  
Tomáš Primus ◽  
Josef Hlavinka ◽  
Pavel Zeman ◽  
Jan Brajer ◽  
Martin Šorm ◽  
...  
Keyword(s):  
Surface Roughness ◽  
High Efficiency ◽  
Steel Substrate ◽  
Cutting Tools ◽  
High Hardness ◽  
Working Time ◽  
Nanosecond Laser ◽  
Altin Coating ◽  
Successful Removal ◽  
Frequency Laser

The lifetime and properties of cutting tools and forming moulds can be prolonged and enhanced by the deposition of hard, thin coatings. After a certain period of usage, the coating will deteriorate. Any remaining coating must be removed prior to successful recoating. Laser stripping is a fast and environmentally friendly coating removal method. In this paper, we present laser removal of two types of coatings deposited on a 1.2379 tool steel substrate, namely, an AlTiN coating with high hardness and a DLC C coating with a small coefficient of friction (COF). A powerful nanosecond laser was employed to remove the coating from the substrate with high efficiency, along with suitable residual surface roughness. Measurements were taken of surface roughness, removed depth, and working time on a stripped area of 1 cm2. The samples were evaluated under a microscope, with a 3D profilometer, and by EDS chemical analysis. Successful removal of the coating was confirmed by optical analysis, but detailed chemical characterisation showed that about 30% of the coating element may remain on the surface. Moreover, a working time of less than 7.5 s per cm2 was obtained in this study. In addition, it was shown that the application of a second low energy, high frequency laser beam pass leads to remelting of the peaks of the material and reduced surface roughness.

High-Pressure Synthesis of High-Purity and High-Performance Diamond and cBN Ceramics

2006 ◽  
Vol 45 ◽  
pp. 885-892 ◽  
Author(s):  
Hitoshi Sumiya
Keyword(s):  
High Pressure ◽  
Diffusion Process ◽  
High Purity ◽  
High Performance ◽  
High Efficiency ◽  
Cutting Tools ◽  
Polycrystalline Diamond ◽  
High Hardness ◽  
Secondary Phases ◽  
Fine Grained

High-purity, single-phase polycrystalline diamond and cBN have been successfully synthesized by direct conversion sintering from graphite and hBN, respectively, under static high pressure and high temperature. The high-purity polycrystalline diamond synthesized directly from graphite at ≧15 GPa and 2300-2500 °C has a mixed texture of a homogeneous fine structure (grain size : 10-30 nm, formed in a diffusion process) and a lamellar structure (formed in a martensitic process). The polycrystalline diamond has very high hardness equivalent to or even higher than that of diamond crystal. The high-purity polycrystalline cBN synthesized from high-purity hBN at 7.7 GPa and 2300 °C consists of homogeneous fine-grained particles (<0.5 μm, formed in a diffusion process). The hardness of the fine-grained high-purity polycrystalline cBN is obviously higher than that of single-crystal cBN. The fine microstructure features without any secondary phases and extremely high hardness of the nano-polycrystalline diamond and the fine-grained polycrystalline cBN are promising for applications in next-generation high-precision and high-efficiency cutting tools.

scholarly journals Polishing Sapphire Substrates by 355 nm Ultraviolet Laser

2012 ◽  
Vol 2012 ◽  
pp. 1-7 ◽  
Author(s):  
X. Wei ◽  
X. Z. Xie ◽  
W. Hu ◽  
J. F. Huang
Keyword(s):  
Surface Roughness ◽  
High Efficiency ◽  
Laser Energy ◽  
Incident Angle ◽  
High Hardness ◽  
Scanning Speed ◽  
Sapphire Crystal ◽  
Initial Surface ◽  
Ultraviolet Laser ◽  
Nanosecond Pulses

This paper tries to investigate a novel polishing technology with high efficiency and nice surface quality for sapphire crystal that has high hardness, wear resistance, and chemical stability. A Q-switched 355 nm ultraviolet laser with nanosecond pulses was set up and used to polish sapphire substrate in different conditions in this paper. Surface roughnessRaof polished sapphire was measured with surface profiler, and the surface topography was observed with scanning electronic microscope. The effects of processing parameters as laser energy, pulse repetition rate, scanning speed, incident angle, scanning patterns, and initial surface conditions on surface roughness were analyzed.

RED STAR TUNGSTEN

Alloy Digest ◽  
1965 ◽  
Vol 14 (12) ◽  
Keyword(s):  
Physical Properties ◽  
Tensile Properties ◽  
Cutting Tools ◽  
High Hardness ◽  
Heat Treating ◽  
High Carbon ◽  
Steel Company ◽  
Vanadium Alloys ◽  
Alloy Tool ◽  
Thread Rolling

Abstract Red Star Tungsten is a high-carbon low-alloy tool steel having high hardness, good toughness, and keen cutting edge. It is recommended for cutting tools, thread rolling dies, paper knives, etc. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as deformation. It also includes information on forming, heat treating, machining, and joining. Filing Code: TS-173. Producer or source: Vanadium Alloys Steel Company.

scholarly journals Experimental Investigation and Comparison of the Thermal Performance of Additively and Conventionally Manufactured Heat Exchangers

Metals ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 574
Author(s):  
Ana Vafadar ◽  
Ferdinando Guzzomi ◽  
Kevin Hayward
Keyword(s):  
Surface Roughness ◽  
Thermal Performance ◽  
Heat Exchangers ◽  
High Efficiency ◽  
Cooling System ◽  
Fluid Dynamic ◽  
Dynamic Performance ◽  
Experimental Studies ◽  
Manufacturing Method ◽  
Industrial Sectors

Air heat exchangers (HXs) are applicable in many industrial sectors because they offer a simple, reliable, and cost-effective cooling system. Additive manufacturing (AM) systems have significant potential in the construction of high-efficiency, lightweight HXs; however, HXs still mainly rely on conventional manufacturing (CM) systems such as milling, and brazing. This is due to the fact that little is known regarding the effects of AM on the performance of AM fabricated HXs. In this research, three air HXs comprising of a single fin fabricated from stainless steel 316 L using AM and CM methods—i.e., the HXs were fabricated by both direct metal printing and milling. To evaluate the fabricated HXs, microstructure images of the HXs were investigated, and the surface roughness of the samples was measured. Furthermore, an experimental test rig was designed and manufactured to conduct the experimental studies, and the thermal performance was investigated using four characteristics: heat transfer coefficient, Nusselt number, thermal fluid dynamic performance, and friction factor. The results showed that the manufacturing method has a considerable effect on the HX thermal performance. Furthermore, the surface roughness and distribution, and quantity of internal voids, which might be created during and after the printing process, affect the performance of HXs.

scholarly journals Effect of Optical and Morphological Control of Single-Structured LEC Device

Micromachines ◽  
2021 ◽  
Vol 12 (7) ◽  
pp. 843
Author(s):  
Woo Jin Jeong ◽  
Jong Ik Lee ◽  
Hee Jung Kwak ◽  
Jae Min Jeon ◽  
Dong Yeol Shin ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Surface Roughness ◽  
Surface Properties ◽  
High Efficiency ◽  
High Surface ◽  
Reduction Rate ◽  
Operating Characteristics ◽  
Emission Layer ◽  
Light Emitting ◽  
Stable Operating

We investigated the performance of single-structured light-emitting electrochemical cell (LEC) devices with Ru(bpy)3(PF6)2 polymer composite as an emission layer by controlling thickness and heat treatment. When the thickness was smaller than 120–150 nm, the device performance decreased because of the low optical properties and non-dense surface properties. On the other hand, when the thickness was over than 150 nm, the device had too high surface roughness, resulting in high-efficiency roll-off and poor device stability. With 150 nm thickness, the absorbance increased, and the surface roughness was low and dense, resulting in increased device characteristics and better stability. The heat treatment effect further improved the surface properties, thus improving the device characteristics. In particular, the external quantum efficiency (EQE) reduction rate was shallow at 100 °C, which indicates that the LEC device has stable operating characteristics. The LEC device exhibited a maximum luminance of 3532 cd/m2 and an EQE of 1.14% under 150 nm thickness and 100 °C heat treatment.

scholarly journals Evaluation of Cutting-Tool Coating on the Surface Roughness and Hole Dimensional Tolerances during Drilling of Al6061-T651 Alloy

Materials ◽  
2021 ◽  
Vol 14 (7) ◽  
pp. 1783
Author(s):  
Hamza A. Al-Tameemi ◽  
Thamir Al-Dulaimi ◽  
Michael Oluwatobiloba Awe ◽  
Shubham Sharma ◽  
Danil Yurievich Pimenov ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Cutting Tool ◽  
Good Practice ◽  
Cutting Tools ◽  
Statistical Design ◽  
Cutting Parameters ◽  
Statistical Design Of Experiments ◽  
Hole Quality ◽  
Coated Tools ◽  
Tool Coating

Aluminum alloys are soft and have low melting temperatures; therefore, machining them often results in cut material fusing to the cutting tool due to heat and friction, and thus lowering the hole quality. A good practice is to use coated cutting tools to overcome such issues and maintain good hole quality. Therefore, the current study investigates the effect of cutting parameters (spindle speed and feed rate) and three types of cutting-tool coating (TiN/TiAlN, TiAlN, and TiN) on the surface finish, form, and dimensional tolerances of holes drilled in Al6061-T651 alloy. The study employed statistical design of experiments and ANOVA (analysis of variance) to evaluate the contribution of each of the input parameters on the measured hole-quality outputs (surface-roughness metrics Ra and Rz, hole size, circularity, perpendicularity, and cylindricity). The highest surface roughness occurred when using TiN-coated tools. All holes in this study were oversized regardless of the tool coating or cutting parameters used. TiN tools, which have a lower coating hardness, gave lower hole circularity at the entry and higher cylindricity, while TiN/TiAlN and TiAlN seemed to be more effective in reducing hole particularity when drilling at higher spindle speeds. Finally, optical microscopes revealed that a built-up edge and adhesions were most likely to form on TiN-coated tools due to TiN’s chemical affinity and low oxidation temperature compared to the TiN/TiAlN and TiAlN coatings.

scholarly journals Remaining Useful Life Prediction of Cutting Tools Using an Inverse Gaussian Process Model

2021 ◽  
Vol 11 (11) ◽  
pp. 5011
Author(s):  
Yuanxing Huang ◽  
Zhiyuan Lu ◽  
Wei Dai ◽  
Weifang Zhang ◽  
Bin Wang
Keyword(s):  
Surface Roughness ◽  
Failure Criterion ◽  
Cutting Tool ◽  
Cutting Tools ◽  
Remaining Useful Life ◽  
Model Parameters ◽  
Inverse Gaussian ◽  
Wear Process ◽  
Useful Life ◽  
Dynamic Wear

In manufacturing, cutting tools gradually wear out during the cutting process and decrease in cutting precision. A cutting tool has to be replaced if its degradation exceeds a certain threshold, which is determined by the required cutting precision. To effectively schedule production and maintenance actions, it is vital to model the wear process of cutting tools and predict their remaining useful life (RUL). However, it is difficult to determine the RUL of cutting tools with cutting precision as a failure criterion, as cutting precision is not directly measurable. This paper proposed a RUL prediction method for a cutting tool, developed based on a degradation model, with the roughness of the cutting surface as a failure criterion. The surface roughness was linked to the wearing process of a cutting tool through a random threshold, and accounts for the impact of the dynamic working environment and variable materials of working pieces. The wear process is modeled using a random-effects inverse Gaussian (IG) process. The degradation rate is assumed to be unit-specific, considering the dynamic wear mechanism and a heterogeneous population. To adaptively update the model parameters for online RUL prediction, an expectation–maximization (EM) algorithm has been developed. The proposed method is illustrated using an example study. The experiments were performed on specimens of 7109 aluminum alloy by milling in the normalized state. The results reveal that the proposed method effectively evaluates the RUL of cutting tools according to the specified surface roughness, therefore improving cutting quality and efficiency.

scholarly journals Investigation on the Surface Quality Obtained during Trochoidal Milling of 6082 Aluminum Alloy

Machines ◽  
2021 ◽  
Vol 9 (4) ◽  
pp. 75
Author(s):  
Nikolaos E. Karkalos ◽  
Panagiotis Karmiris-Obratański ◽  
Szymon Kurpiel ◽  
Krzysztof Zagórski ◽  
Angelos P. Markopoulos
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Process Parameters ◽  
Manufacturing Industry ◽  
High Surface ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
High Surface Quality ◽  
Trochoidal Milling

Surface quality has always been an important goal in the manufacturing industry, as it is not only related to the achievement of appropriate geometrical tolerances but also plays an important role in the tribological behavior of the surface as well as its resistance to fatigue and corrosion. Usually, in order to achieve sufficiently high surface quality, process parameters, such as cutting speed and feed, are regulated or special types of cutting tools are used. In the present work, an alternative strategy for slot milling is adopted, namely, trochoidal milling, which employs a more complex trajectory for the cutting tool. Two series of experiments were initially conducted with traditional and trochoidal milling under various feed and cutting speed values in order to evaluate the capabilities of trochoidal milling. The findings showed a clear difference between the two milling strategies, and it was shown that the trochoidal milling strategy is able to provide superior surface quality when the appropriate process parameters are also chosen. Finally, the effect of the depth of cut, coolant and trochoidal stepover on surface roughness during trochoidal milling was also investigated, and it was found that lower depths of cut, the use of coolant and low values of trochoidal stepover can lead to a considerable decrease in surface roughness.

Characteristic properties of AlTiN and TiN coated HSS materials

2015 ◽  
Vol 67 (2) ◽  
pp. 172-180 ◽  
Author(s):  
Mumin Sahin ◽  
Cenk Misirli ◽  
Dervis Özkan
Keyword(s):  
Surface Roughness ◽  
Tensile Strength ◽  
High Speed ◽  
Cutting Tools ◽  
High Speed Steel ◽  
Wear Properties ◽  
Content Type ◽  
X Ray ◽  
Number Of Cycles ◽  
Future Work

Purpose – The purpose of this paper is to examine mechanical and metallurgical properties of AlTiN- and TiN-coates high-speed steel (HSS) materials in detail. Design/methodology/approach – In this study, HSS steel parts have been processed through machining and have been coated with AlTiN and TiN on physical vapour deposition workbench at approximately 6,500°C for 4 hours. Tensile strength, fatigue strength, hardness tests for AlTiN- and TiN-coated HSS samples have been performed; moreover, energy dispersive X-ray spectroscopy and X-ray diffraction analysis and microstructure analysis have been made by scanning electron microscopy. The obtained results have been compared with uncoated HSS components. Findings – It was found that tensile strength of TiAlN- and TiN-coated HSS parts is higher than that of uncoated HSS parts. Highest tensile strength has been obtained from TiN-coated HSS parts. Number of cycles for failure of TiAlN- and TiN-coated HSS parts is higher than that for HSS parts. Particularly TiN-coated HSS parts have the most valuable fatigue results. However, surface roughness of fatigue samples may cause notch effect. For this reason, surface roughness of coated HSS parts is compared with that of uncoated ones. While the average surface roughness (Ra) of the uncoated samples was in the range of 0.40 μm, that of the AlTiN- and TiN-coated samples was in the range of 0.60 and 0.80 μm, respectively. Research limitations/implications – It would be interesting to search different coatings for cutting tools. It could be the good idea for future work to concentrate on wear properties of tool materials. Practical implications – The detailed mechanical and metallurgical results can be used to assess the AlTiN and TiN coating applications in HSS materials. Originality/value – This paper provides information on mechanical and metallurgical behaviour of AlTiN- and TiN-coated HSS materials and offers practical help for researchers and scientists working in the coating area.

Sign in / Sign up

Export Citation Format

Share Document