scholarly journals Pt-Rh Alloys: Investigation Of Tensile Strength And Elongation At High Temperatures

2015 ◽  
Vol 60 (2) ◽  
pp. 643-647
Author(s):  
B. Trumić ◽  
L. Gomidželović ◽  
S. Marjanović ◽  
V. Krstić ◽  
A. Ivanović ◽  
...  

AbstractIn this paper are presented investigation results of tensile strength and elongation of selected alloys from Pt-Rh system. Samples with the content of rhodium in a concentration range of 7-40% (wt.) were studied. Studies were performed in the temperature range 1100-1500°C at a stress of 2-20 MPa. A universal device for measuring hardness was used to measure the Vickers hardness. For investigation of time strength and elongation at high temperatures, the device Mayes MK2 TC/10 was used. It was found that the value of tensile strength increases with increasing rhodium content, and decreases with increasing temperature. Elongation decreases to 7% Rh, then increases with increasing rhodium content to 15% and then slowly decreases again. With increasing temperature there is a slight increase in elongation.

Holzforschung ◽  
2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Kong Yue ◽  
Feng Wang ◽  
Weidong Lu ◽  
Zhongqiu Tang ◽  
Zhangjing Chen ◽  
...  

Abstract A model for engineered wood was developed that considers the parallel-to-grain tensile strength of finger-jointed lumber at high temperatures relevant to fire conditions. The finger-jointed lumber was composed of Douglas fir, larch, and poplar wood with phenol-resorcinol-formaldehyde (PRF) as an adhesive. The tensile properties of the finger-jointed lumber were evaluated at high temperatures under oxygen-free conditions, i.e. in a nitrogen atmosphere. A combination of chemical and thermal-physical property analysis of the PRF adhesive and microscopic observations on the glueline was used to discuss the reduction of tensile strength of the parallel-to-grain finger-jointed lumber at variable temperature. The results show that the tensile strength of the finger-jointed lumber decreased linearly with increasing temperature. The parallel-to-grain tensile strength of the PRF finger-jointed samples at 20 and 280 °C were 84 and 5% of the tensile strength of the solid wood at 20 °C, respectively. The thermal-physical properties and scanning electron microscopy analysis revealed that the pyrolysis intensity of the PRF adhesive was lower than that of the wood at 220 °C or higher.


1981 ◽  
Vol 36 (12) ◽  
pp. 1305-1308 ◽  
Author(s):  
D. Ploumbidis ◽  
R. Rünger ◽  
R. Bucklisch

AbstractThe Knight shift of the 51V resonance has been measured as a function of temperature in poly-crystalline V3Si and VSi2 samples. For the VaSi system the measurements have been extended to the temperature range from 400 K up to 1250 K, whereas for VSi2 the first NMR measurements at all have been carried out, covering the range 300 to 1250 K. The observed 51V Knight shift in VSi2 is negative (K51V (T=272 K) = -0.15%) and tends to zero with increasing temperature.


1952 ◽  
Vol 25 (1) ◽  
pp. 33-35 ◽  
Author(s):  
A. S. Kuzminskii˘ ◽  
I. A. Shokhin ◽  
R. M. Belitzkaya

Abstract In theories developed by Kuzminskii˘ and his collaborators concerning the mechanism of oxidation of rubbers, the question of a direct thermal effect on their structure was not discussed. Nevertheless, with certain rubbers, structural changes which are caused by high temperatures play a very important part in the total complex of structural changes undergone by these rubbers during processing and, after vulcanization, by their products during service. Dogadkin, Zayonchkovskii˘, Zayonchkovskaya, Pisarenko, and Astafyez, Kuzminskii˘, Shanin, Degteva, Lapteva, and other Soviet investigators have shown that, when butadiene rubbers are heated in the temperature range of 100–200° C, structural changes take place which are characterized by increases of tensile strength and modulus, decrease of extensibility, decrease of unsaturation, etc. The question of the causes of such extensive changes in rubber is the subject of this discussion. Rebinder has proven unsubstantiated the reasoning of several investigators regarding these processes, and has shown the necessity of carrying out direct experiments which would provide an explanation of their nature.


1972 ◽  
Vol 38 (297) ◽  
pp. 583-592 ◽  
Author(s):  
P. G. Rouxhet ◽  
J. L. Gillard ◽  
J. J. Fripiat

SummaryThe oxidation of amosite, crocidolite, and biotite has been determined at temperatures up to nearly 900 °C under both a vacuum (10−2 mm Hg) and oxygen (10 and 600 mm Hg). Infrared spectra gave the loss of constitutional hydroxyl under these conditions. The loss of tensile strength of the amphiboles with increasing temperature seems to be due to thermal decomposition. For the three minerals oxidation takes place progressively over a broad temperature range. Under vacuum there is a certain temperature above which the ferric iron previously formed is reduced; this temperature corresponds to the completion of the loss of hydroxyl. The crocidolite anhydride in the literature is most probably an oxycrocidolite formed by dehydrogenation, the truly dehydroxylated zones being amorphous.


2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Christian Aermes ◽  
Alexander Hayn ◽  
Tony Fischer ◽  
Claudia Tanja Mierke

AbstractThe knowledge of cell mechanics is required to understand cellular processes and functions, such as the movement of cells, and the development of tissue engineering in cancer therapy. Cell mechanical properties depend on a variety of factors, such as cellular environments, and may also rely on external factors, such as the ambient temperature. The impact of temperature on cell mechanics is not clearly understood. To explore the effect of temperature on cell mechanics, we employed magnetic tweezers to apply a force of 1 nN to 4.5 µm superparamagnetic beads. The beads were coated with fibronectin and coupled to human epithelial breast cancer cells, in particular MCF-7 and MDA-MB-231 cells. Cells were measured in a temperature range between 25 and 45 °C. The creep response of both cell types followed a weak power law. At all temperatures, the MDA-MB-231 cells were pronouncedly softer compared to the MCF-7 cells, whereas their fluidity was increased. However, with increasing temperature, the cells became significantly softer and more fluid. Since mechanical properties are manifested in the cell’s cytoskeletal structure and the paramagnetic beads are coupled through cell surface receptors linked to cytoskeletal structures, such as actin and myosin filaments as well as microtubules, the cells were probed with pharmacological drugs impacting the actin filament polymerization, such as Latrunculin A, the myosin filaments, such as Blebbistatin, and the microtubules, such as Demecolcine, during the magnetic tweezer measurements in the specific temperature range. Irrespective of pharmacological interventions, the creep response of cells followed a weak power law at all temperatures. Inhibition of the actin polymerization resulted in increased softness in both cell types and decreased fluidity exclusively in MDA-MB-231 cells. Blebbistatin had an effect on the compliance of MDA-MB-231 cells at lower temperatures, which was minor on the compliance MCF-7 cells. Microtubule inhibition affected the fluidity of MCF-7 cells but did not have a significant effect on the compliance of MCF-7 and MDA-MB-231 cells. In summary, with increasing temperature, the cells became significant softer with specific differences between the investigated drugs and cell lines.


In the first paper of this series (Burgoyne 1937) the kinetics of the isothermal oxidation above 400° C of several aromatic hydrocarbons was studied. The present communication extends this work to include the phenomena of ignition in the same temperature range, whilst the corresponding reactions below 400° C form the subject of further investigations now in progress. The hydrocarbons at present under consideration are benzene, toluene, ethylbenzene, n -propylbenzene, o-, m - and p -xylenes and mesitylene.


2009 ◽  
Vol 24 (2) ◽  
pp. 430-435 ◽  
Author(s):  
D. Li ◽  
H.H. Hng ◽  
J. Ma ◽  
X.Y. Qin

The thermoelectric properties of Nb-doped Zn4Sb3 compounds, (Zn1–xNbx)4Sb3 (x = 0, 0.005, and 0.01), were investigated at temperatures ranging from 300 to 685 K. The results showed that by substituting Zn with Nb, the thermal conductivities of all the Nb-doped compounds were lower than that of the pristine β-Zn4Sb3. Among the compounds studied, the lightly substituted (Zn0.995Nb0.005)4Sb3 compound exhibited the best thermoelectric performance due to the improvement in both its electrical resistivity and thermal conductivity. Its figure of merit, ZT, was greater than the undoped Zn4Sb3 compound for the temperature range investigated. In particular, the ZT of (Zn0.995Nb0.005)4Sb3 reached a value of 1.1 at 680 K, which was 69% greater than that of the undoped Zn4Sb3 obtained in this study.


1961 ◽  
Vol 39 (7) ◽  
pp. 1029-1039 ◽  
Author(s):  
M. J. Laubitz

A method is given for exact mathematical analysis of linear heat flow systems used in measuring thermal conductivity at high temperatures. It is shown that a popular version of such a system is very sensitive to the alignment of its components, which seriously limits the temperature range of its satisfactory use.


2012 ◽  
Vol 159 ◽  
pp. 346-350
Author(s):  
Shu Min Liu ◽  
Jian Bin Zhang

The elevated temperature short-time tensile test with the sample of casting low nickel stainless steel was conducted on SHIMADZU AG-10 at ten temperatures 300, 500, 600, 700, 800, 950, 1000, 1050, 1100, and 1250°C, respectively. The stress-strain curves with the thermal deformation at the different temperatures, the peak stress intensity-temperature curve, and the reduction percentage of cross sectional area-temperature curve were obtained. Metallographic test samples were prepared and the morphology of deforming zone was observed by optical microscopy. The experimental results show that the tensile strength of the test samples decreases with increasing temperature. From 300 to 800°C, the work harding occurred and the tensile strength increases with increasing strain. The work softening occurred and the tensile strength decreases with increasing strain at temperatures of 800 to 1250°C. The minimum value of reduction percentage was measured at 800 °C. The austenite and delta-ferrite are the main phase in the tested samples. When the tensile temperatures are increased to 1200°C, the delta-ferrite became thinner and broke down to be spheroidized.


2007 ◽  
Vol 26-28 ◽  
pp. 409-412 ◽  
Author(s):  
Jae Seol Lee ◽  
Hyeon Taek Son ◽  
Ki Yong Lee ◽  
Soon Sub Park ◽  
Dae Guen Kim ◽  
...  

AZ31 Mg / 5083 Al clad sheet was fabricated by the hot rolling method and its mechanical properties were investigated in this study. The tensile strength and yield strength of Mg- Al clad samples were slightly higher than that of AZ31 Mg sample, resulting in high strength 5083 Al alloy. Also, in the case of the AZ31 Mg sample, tensile strength indicated different values to the rolling directions. The thickness of interface layers between magnesium and aluminum materials increased with increasing rolling temperature. The thickness of interface layer was about 1.2 μm and 1.6 μm, respectively. The difference of thickness on the interface layer with variation of rolling temperature was attributed to promote the diffusion between magnesium and aluminum materials. The Vickers hardness of Mg-Al interface layer was around 125 Hv. The interface layer composed of hard inter-metallic phases which may act a increment of Vickers hardness depending upon its thickness.


Sign in / Sign up

Export Citation Format

Share Document