scholarly journals Kearns texture parameters, mechanical properties and damageability of titanium sheet after alternating bending

2021 ◽  
Vol 22 (3) ◽  
pp. 543-550
Author(s):  
V.V. Usov ◽  
N.M. Shkatulyak ◽  
O.S. Savchuk ◽  
N.I. Rybak
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Ultimate Tensile Strength ◽  
Yield Stress ◽  
Rolling Direction ◽  
Initial State ◽  
Texture Parameters ◽  
Experimental Values ◽  
Alternating Bending

This work aims to determine the Kearns texture parameters and evaluate on their basis the elastic moduli, mechanical properties (ultimate tensile strength, conditional yield stress), as well as damageability parameters of the sheets commercial titanium (CT-grade 1: 0.04% Fe; 0.015% C; 0.05% N 0.05% c; 0.009% H)  as delivered after rolling and annealing at 840°C (original sheet) and further alternating bending (AB) in the amount of 0.5; 1, 3 and 5 cycles. Damageability parameters characterizing damage accumulation were determined from the elastic modulus change after the above-mentioned number of AB cycles relative to the values ​​of the elastic modulus in different directions of the original sheet of the studied titanium. The elastic constants of the single crystal and the Kearns texture parameters were used to estimate the elastic modulus in the rolling direction (RD) and transverse direction (TD) of the original sheet, and sheets after an above number of AB cycles. The deviation of the calculated and experimental values ​​of the elastic modulus did not exceed 5%. The deviation of the calculated and experimental values of the ultimate tensile strength and yield stress in the RD and TD both in the initial state and after the corresponding number cycles of the AB did not exceed 10%.

Experimental Investigation of Stratasys J750 PolyJet Printer: Effects of Orientation and Layer Thickness on Mechanical Properties

2019 ◽  
Author(s):  
Xingjian Wei ◽  
Abhinav Bhardwaj ◽  
Chin-Cheng Shih ◽  
Li Zeng ◽  
Bruce Tai ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Ultimate Tensile Strength ◽  
Layer Thickness ◽  
Axial Direction ◽  
Limited Information ◽  
Direction Parallel ◽  
Control Factors ◽  
Significant Difference

Abstract The J750 PolyJet printer is the newest model of full-color, multi-material 3D printer from Stratasys. Currently, limited information is available about the effects of control factors on mechanical properties such as elastic modulus, ultimate tensile strength, and elongation. In this study, the effects of two control factors, orientation and layer thickness, on mechanical properties of samples printed by the Stratasys J750 printer are investigated. The results show that orientation significantly affects mechanical properties. Specifically, samples printed with its axial direction parallel to the direction of printing have the highest elastic modulus, and elongation, whereas samples printed with its axial direction perpendicular to the direction of printing have the highest ultimate tensile strength. Also, layer thickness makes a significant difference for mechanical properties, and larger layer thickness leads to higher ultimate tensile strength and elongation. These results would be valuable to researchers and practitioners who use J750.

scholarly journals Mechanical Properties of Laser-Sintered 3D-Printed Cobalt Chromium and Soft-Milled Cobalt Chromium

Prosthesis ◽  
2020 ◽  
Vol 2 (4) ◽  
pp. 313-320
Author(s):  
Abdullah Barazanchi ◽  
Kai Chun Li ◽  
Basil Al-Amleh ◽  
Karl Lyons ◽  
J. Neil Waddell
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Ultimate Tensile Strength ◽  
High Stress ◽  
Uniform Structure ◽  
Cobalt Chromium ◽  
Proof Stress ◽  
Fracture Surfaces ◽  
3D Printed

Purpose: To compare the mechanical properties and fracture behaviour of laser-sintered/3D-printed cobalt chromium (LS CoCr) with soft-milled cobalt chromium (SM CoCr) to assess their suitability for use in high-stress areas in the oral cavity. Material and Method: Two computer-aided manufacturing methods were used to fabricate dumbbell specimens in accordance with the ASTM standard E8. Specimens were fractured using tensile testing and elastic modulus, and proof stress and ultimate tensile strength were calculated. Fracture surfaces were examined using scanning electron microscopy. Plate specimens were also fabricated for the examination of hardness and elastic modulus using nanoindentation. Unpaired t-test was used to evaluate statistical significance. Results: LS CoCr specimens were found to have significantly higher ultimate tensile strength (UTS) and proof stress (PS) (p < 0.05) but not a significantly higher elastic modulus (p > 0.05). Examination of the dumbbell fracture surfaces showed uniform structure for the LS CoCr specimens whilst the SM CoCr specimens were perforated with porosities; neither showed an obvious point of fracture. Nanoindentation also showed that LS CoCr specimens possessed higher hardness compared with SM CoCr specimens. Conclusion: LS CoCr and SM CoCr specimens were both found to exhibit uniformly dense structure; although porosities were noted in the SM CoCr specimens. LS CoCr specimens were found to have superior tensile properties, likely due to lack of porosities, however both had mean values higher than those reported in the literature for cast CoCr. Uniformity of structure and high tensile strength indicates that LS CoCr and SM CoCr fabricated alloys are suitable for long-span metallic frameworks for use in the field of prosthodontics.

Reinforcing Inconel 718 Superalloy by Nano-TiC Particles in Selective Laser Melting

2015 ◽  
Author(s):  
Yachao Wang ◽  
Jing Shi ◽  
Yun Wang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Additive Manufacturing ◽  
Ultimate Tensile Strength ◽  
Yield Stress ◽  
Selective Laser Melting ◽  
Inconel 718 ◽  
Reinforcement Particle ◽  
Manufacturing Processes ◽  
Laser Melting

Metal components produced by additive manufacturing processes usually have inferior properties and performances as compared with the counterparts by the traditional forming and machining processes. To close the gap, the metal matrix can be strengthened by adding reinforcement particles in additive manufacturing processes. This research presents the fabrication of nano-TiC reinforced Inconel 718 composites using selective laser melting (SLM). Tensile and wear performance tests are conducted to evaluate the mechanical properties of the formed composites. It is discovered that the composites exhibit improved mechanical properties in terms of ultimate tensile strength and yield stress. Compared with the pure Inconel 718 specimens by SLM, the ultimate tensile strength and yield stress of the reinforced Inconel 718 increase by 207 MPa and 204 MPa, respectively, with 0.5 wt.% addition of nano-TiC particle. Smaller increases are observed with 0.25 wt.% and 1.0 wt.% nano-TiC additions. On the other hand, the addition of nano-TiC particles decreases the ductility of Inconel 718. To investigate the strengthening mechanism of nano reinforcement particles in SLM, the microstructures with different levels of nano-TiC particles are observed. The results indicate that the microstructure of Inconel 718 is remarkably refined by the TiC particles, and the reinforcement particle significantly impede the growth of columnar grain in the solidification process.

Influence of Crystallographic Texture on Mechanical Properties in Cold Rolled 7XXX Series Al Alloys Used in Space Applications

2012 ◽  
Vol 710 ◽  
pp. 539-544 ◽  
Author(s):  
P. Ramesh Narayanan ◽  
Satyam Suwas ◽  
K. Sreekumar ◽  
Parameshwar Prasad Sinha ◽  
Srinivasa Ranganathan
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Yield Strength ◽  
Crystallographic Texture ◽  
Shear Banding ◽  
Rolling Direction ◽  
The Other ◽  
Space Applications ◽  
Plastic Strain Ratio

This paper covers the influence of crystallographic texture on the mechanical properties in two of the most important high strength Al-Zn-Mg family of aluminium alloys, viz., AA7075 and AFNOR7020 alloys, used in the Aerospace industry. AFNOR7020 Alloy developed a stronger texture compared to the other two alloys. S component of texture is stronger in AA7075 alloy whereas the Bs component is stronger in AFNOR7020 alloy. This is attributed to the shear banding which was found absent in the other alloy. The starting material, AA7075 in T7352 condition and AFNOR7020 in T652 condition show some degree of anisotropy of mechanical properties with regard to yield strength and ultimate tensile strength. Higher degree of deformation leads to more pronounced anisotropy in mechanical properties with regard to yield strength and ultimate tensile strength, with a maxima along the transverse direction. For the alloys, experimentally measured Plastic Strain Ratio, r value, which is a measure of the texture present in the material in the deformation conditions, agree well with the computed values with a maximum at 45oorientation to the rolling direction.

Recycling of Radiation Crosslinked Polyamide 6

2015 ◽  
Vol 752-753 ◽  
pp. 331-336
Author(s):  
Jan Navratil ◽  
Miroslav Manas ◽  
Michal Stanek ◽  
David Manas ◽  
Martin Bednarik ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Ultimate Tensile Strength ◽  
Impact Toughness ◽  
High Density Polyethylene ◽  
Polyamide 6 ◽  
High Density ◽  
Material Stiffness ◽  
Plastic Materials

Growing usage of radiation crosslinked plastic materials and utilization of their advantageous properties might raise a question of their future recycling. This paper deals with utilization of recycled irradiated polyamide 6 (rPA6x) which is used as a filler into low and high-density polyethylene (LDPE/HDPE) in concentrations 10 and 30 %. Mechanical properties of such blends were investigated and compared. Both blends show similar trend at all observed material characteristics. Elastic modulus representing material stiffness grown with increasing amount of the filler. Ultimate tensile strength and impact toughness decreased and hardness slightly increased. All the obtained results show that it is possible to use recycled radiation crosslinked PA6 as a filler but it is necessary to count with properties change.

Effect of cold rolling on microstructural and mechanical properties of MG-7LI alloy

2019 ◽  
Vol 34 (01n03) ◽  
pp. 2040035
Author(s):  
Xiang Cai ◽  
Yanxin Qiao ◽  
Baojie Wang ◽  
Huiling Zhou ◽  
Yuxin Wang
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Yield Strength ◽  
Cold Rolling ◽  
Tensile Test ◽  
Rolling Direction ◽  
Scanning Electron

The influence of rolling on nanomechanical and mechanical behavior of Mg-7Li alloy was investigated by nanoindentation, tensile test and scanning electron microscopy (SEM), respectively. The [Formula: see text]-Mg phase elongated along the rolling direction and gradually cracked. As the rolling ratio increased from 3 to 10, the hardness of [Formula: see text]-Mg and [Formula: see text]-Li phase increased by 7.35% and 20.75%, respectively. The fracture of alloys changed from ductile fracture to quasi-cleavage fracture. The yield strength and ultimate tensile strength increased by 23 MPa and 12 MPa, respectively, while elongation reduced by 12.5%.

Effect of the Thermomechanical Processing on Microstructure and Properties of an Al-Ce Alloy

2012 ◽  
Vol 706-709 ◽  
pp. 361-366 ◽  
Author(s):  
Anna Mogucheva ◽  
Dmitriy Zyabkin ◽  
Rustam Kaibyshev
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Electric Conductivity ◽  
Yield Stress ◽  
Room Temperature ◽  
Thermomechanical Processing ◽  
Fold Increase ◽  
Angular Pressing ◽  
Eutectic Particles

Effect of equal channel angular pressing (ECAP) at room temperature and subsequent annealing at temperatures ranging from 450 to 600°C on microstructure, mechanical properties and electric conductivity of an Al-8%Ce alloy was examined It was shown that Al4Ce-type eutectic particles having plate-like shape break under ECAP; distribution of the particles appears to be more homogeneous. ECAP leads to about two-fold increase in yield stress (YS) and ultimate tensile strength (UTS); ductility and electric conductivity decrease significantly. Under following annealing, the spheroidizing and coagulation of Al4Ce-type particles occur extensively resulting in decreased strength and increased electric conductivity and ductility.

scholarly journals Microstructure and Mechanical Properties of Structural Steel after Dynamic Cold Working Deformation/ Wpływ Dynamicznego Odkształcenia Plastycznego Na Zimno Na Mikrostrukturę I Własności Stali Konstrukcyjnej

2014 ◽  
Vol 59 (4) ◽  
pp. 1699-1703 ◽  
Author(s):  
J. Pacyna ◽  
R. Dabrowski ◽  
E. Rozniata ◽  
A. Kokosza ◽  
R. Dziurka
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Impact Strength ◽  
Yield Stress ◽  
Cold Working ◽  
Strong Relationship ◽  
The Common ◽  
Reduction Of Area ◽  
Grade Steel

Abstract The results of the selected mechanical properties i.e. ultimate tensile strength (UTS), yield stress (YS), elongation (EL), reduction of area (RA), hardness (HV) and impact strength (KCV) of the common, S235JR grade steel, are presented in the paper. A strong relationship between the above mentioned properties and cooling rates after hot rolling of rods, made of this steel, was found. Additionally, the possibility of further enhancing of mechanical properties (UTS and YS) by the controlled, dynamic cold working, was shown. The use of such deformation, through changes in the microstructure allows for the upper yield stress (YS) increase - app. 10% and ultimate tensile strength UTS - app. 5%. Simultaneously, very high indicators of plasticity (EL, RA) and impact strength (KCV) are retained, as they were immediately after the rolling. The possibility of improving the mechanical properties of rods made of this steel grade has a great technological and commercial importance for its manufacturers, as well as for their final users.

Effect of Bone Mineral Content on the Tensile Properties of Cortical Bone: Experiments and Theory

2003 ◽  
Vol 125 (6) ◽  
pp. 785-793 ◽  
Author(s):  
S. P. Kotha ◽  
N. Guzelsu
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Bone Mineral Content ◽  
Cortical Bone ◽  
Yield Stress ◽  
Bone Tissue ◽  
Bone Mineral ◽  
Mineral Content ◽  
Organic Matrix ◽  
Experimental Values

The effect of mineral volume fraction on the tensile mechanical properties of cortical bone tissue is investigated by theoretical and experimental means. The mineral content of plexiform, bovine bone was lowered by 18% and 29% by immersion in fluoride solutions for 3 days and 12 days, respectively. The elastic modulus, yield strength and ultimate strength of bone tissue decreased, while the ultimate strain increased with a decrease in mineral content. The mechanical behavior of bone tissue was modeled by using a micro-mechanical shear lag theory consisting of overlapped mineral platelets reinforcing the organic matrix. The decrease in yield stress, by the 0.002 offset method, of the fluoride treated bones were matched in the theoretical curves by lowering the shear yield stress of the organic matrix. The failure criterion used was based on failure stresses determined from a failure envelope (Mohr’s circle), which was constructed using experimental data. It was found that the model predictions of elastic modulus got worse with a decrease in mineral content (being 7.9%, 17.2% and 33.0% higher for the control, 3-day and 12-day fluoride-treated bones). As a result, the developed theory could not fully predict the yield strain of bones with lowered mineral content, being 12.9% and 21.7% lower than the experimental values. The predicted ultimate stresses of the bone tissues with lower mineral contents were within ±10% of the experimental values while the ultimate strains were 12.7% and 26.3% lower than the experimental values. Although the model developed in this study did not take into account the presence of hierarchical structures, voids, orientation of collagen molecules and micro cracks, it still indicated that the mechanical properties of the organic matrix depend on bone mineral content.

Effect of Pre-Straining Method on Mechanical Properties of Thermo-Mechanically Processed Al-Cu-Mg Alloy

2018 ◽  
Vol 385 ◽  
pp. 364-369 ◽  
Author(s):  
Ivan Zuiko ◽  
Vladislav Kulitckii ◽  
Rustam Kaibyshev
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Yield Stress ◽  
Homogeneous Distribution ◽  
Precipitation Behavior ◽  
Nucleation Sites ◽  
Elongation To Failure ◽  
Phase Plates ◽  
Distribution Of Dislocations

The present study deals with the effect of pre-deformation technique of AA2519 alloy (Al–5.64Cu–0.33Mn–0.23Mg–0.15Zr–0.11Ti–0.09V–0.08Fe–0.01Si (wt. %)) under T8 tempers, on condition that intermediate strains are equal. After undergoing T87 by pre-stretching and peak ageing the alloy demonstrates the yield stress, ultimate tensile strength and elongation to failure of 425.4±2.4 MPa, 475±2.4 MPa, 12.1±0.4%, respectively. The 7% pre-straining by rolling leads to-5% decrease in yield stress, practically the same ultimate tensile strength and-20% decrease in ductility. This effect can be ascribed to more homogeneous distribution of dislocations which act as heterogeneous nucleation sites for the θ′-phase precipitation. In addition to precipitates of the Al–Cu family (θ′′ and θ′), Ω-phase plates on {111}α habit plane was observed. The effect of pre-straining prior to ageing on the precipitation behavior and its relation with mechanical properties of the AA2519 is considered.

Sign in / Sign up

Export Citation Format

Share Document