Effect of the Thermomechanical Processing on Microstructure and Properties of an Al-Ce Alloy

2012 ◽  
Vol 706-709 ◽  
pp. 361-366 ◽  
Author(s):  
Anna Mogucheva ◽  
Dmitriy Zyabkin ◽  
Rustam Kaibyshev
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Electric Conductivity ◽  
Yield Stress ◽  
Room Temperature ◽  
Thermomechanical Processing ◽  
Fold Increase ◽  
Angular Pressing ◽  
Eutectic Particles

Effect of equal channel angular pressing (ECAP) at room temperature and subsequent annealing at temperatures ranging from 450 to 600°C on microstructure, mechanical properties and electric conductivity of an Al-8%Ce alloy was examined It was shown that Al4Ce-type eutectic particles having plate-like shape break under ECAP; distribution of the particles appears to be more homogeneous. ECAP leads to about two-fold increase in yield stress (YS) and ultimate tensile strength (UTS); ductility and electric conductivity decrease significantly. Under following annealing, the spheroidizing and coagulation of Al4Ce-type particles occur extensively resulting in decreased strength and increased electric conductivity and ductility.

Strength of Commercial Aluminum Alloys after Equal Channel Angular Pressing and Post-ECAP Processing

2006 ◽  
Vol 114 ◽  
pp. 91-96 ◽  
Author(s):  
Maxim Yu. Murashkin ◽  
M.V. Markushev ◽  
Julia Ivanisenko ◽  
Ruslan Valiev
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Aluminum Alloys ◽  
Ultimate Tensile Strength ◽  
Equal Channel Angular Pressing ◽  
Room Temperature ◽  
Solution Treatment ◽  
Ecap Processing ◽  
Angular Pressing

The effects of equal channel angular pressing (ECAP), further heat treatment and rolling on the structure and room temperature mechanical properties of the commercial aluminum alloys 6061 (Al-0.9Mg-0.7Si) and 1560 (Al-6.5Mg-0.6Mn) were investigated. It has been shown that the strength of the alloys after ECAP is higher than that achieved after conventional processing. Prior ECAP solution treatment and post-ECAP ageing can additionally increase the strength of the 6061 alloy. Under optimal ageing conditions a yield strength (YS) of 434 MPa and am ultimate tensile strength (UTS) of 470 MPa were obtained for the alloy. Additional cold rolling leads to a YS and UTS of 475 and 500 MPa with 8% elongation. It was found that the post-ECAP isothermal rolling of the 1560 alloy resulted in the formation of a nano-fibred structure and a tensile strength (YS = 540 MPa and UTS = 635 MPa) that has never previously been observed in commercial non-heat treatable alloys.

Mechanical Properties of Ultrafine-Grained Al Alloy for Engineering Machinery

2012 ◽  
Vol 629 ◽  
pp. 198-202 ◽  
Author(s):  
Ping Yang ◽  
Kai Huai Yang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Equal Channel Angular Pressing ◽  
Room Temperature ◽  
Al Alloy ◽  
Fracture Modes ◽  
Annealed State ◽  
Angular Pressing ◽  
Ultrafine Grained

Three groups of commercial 1050 Al alloy were subjected to equal channel angular pressing (ECAP) at room temperature using route A, route C and route Bc, respectively. Mechanical properties and fracture modes of as-annealed and ECAPed samples were investigated. The microhardness of 1050 Al fabricated by ECAP increases by a factor of about 1.5 compared to the as-annealed state. The ultimate tensile strength (UTS) increases significantly after ECAP, while the elongation decreases. But they are strongly dependence on the number of ECAP passes and the pressing route. The UTS and elongation of the samples processed by route Bc are best, consequently, the static toughness U of the samples is enhanced. Besides, all specimens subjected to ECAP deformation failed in a ductile manner.

Effect of ECAP Prior to Aging on Microstructure, Precipitation Behaviour and Mechanical Properties of an Al-Cu-Mg Alloy

2018 ◽  
Vol 385 ◽  
pp. 290-295 ◽  
Author(s):  
Ivan Zuiko ◽  
Marat Gazizov ◽  
Rustam Kaibyshev
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Microstructure Evolution ◽  
Thermomechanical Processing ◽  
High Strength ◽  
Mg Alloy ◽  
Angular Pressing ◽  
Precipitation Behaviour ◽  
Peak Aged

Microstructure, precipitation behaviour and mechanical properties of an Al-5.64Cu-0.33Mn-0.23Mg-0.14Zr-0.11Ti (in wt. %) alloy subjected to thermomechanical processing (TMP) involving equal-channel angular pressing (ECAP) at ambient temperature to total strains (ε) of ~1 and ~2 followed by aging at 180°C for 0-28 h have been investigated and compared with conventional aging at the same temperature (T6 state). TMP led to significant increase in yield stress (YS) and ultimate tensile strength (UTS) and decrease in elongation-to-fracture as compared to the peak-aged T6 state. The YS, UTS and δ values attained after ECAP to ε ~ 2 followed by peak ageing were ~510 MPa, ~540 MPa and ~7.6%, respectively. The changes in mechanical properties were related to microstructure evolution and precipitation behaviour. TMP conditions obtaining a high-strength state of the Al-Cu-Mg alloy are discussed.

scholarly journals Effects of Substitution of Y with Yb and Ce on the Microstructures and Mechanical Properties of Mg88.5Zn5Y6.5

Metals ◽  
2020 ◽  
Vol 11 (1) ◽  
pp. 31
Author(s):  
Hongxin Liao ◽  
Taekyung Lee ◽  
Jiangfeng Song ◽  
Jonghyun Kim ◽  
Fusheng Pan
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Yield Strength ◽  
Creep Resistance ◽  
Room Temperature ◽  
High Thermal Stability ◽  
Long Period ◽  
Microstructures And Mechanical Properties

The microstructures and mechanical properties of the Mg88.5Zn5Y6.5-XREX (RE = Yb and Ce, X = 0, 1.5, 3.0, and 4.5) (wt.%) alloys were investigated in the present study. Mg88.5Zn5Y6.5 is composed of three phases, namely, α-Mg, long-period stacking ordered (LPSO) phases, and intermetallic compounds. The content of the LPSO phases decreased with the addition of Ce and Yb, and no LPSO phases were detected in Mg88.5Zn5Y2.0Yb4.5. The alloys containing the LPSO phases possessed a stratified microstructure and exhibited excellent mechanical properties. Mg88.5Zn5Y5.0Ce1.5 exhibited the highest creep resistance and mechanical strength at both room temperature and 200 °C, owing to its suitable microstructure and high thermal stability. The yield strength of Mg88.5Zn5Y5.0Ce1.5 at room temperature was 358 MPa. The ultimate tensile strength of Mg88.5Zn5Y5.0Ce1.5 at room temperature and 200 °C was 453 MPa and 360 MPa, respectively.

Influence of Additions Sb on Mechanical Properties and Deformation Features of AZ31-Mg Alloy

2006 ◽  
Vol 15-17 ◽  
pp. 497-500
Author(s):  
Ling Wang ◽  
Su Gui Tian ◽  
Keun Yong Sohn ◽  
Kyung Hyun Kim
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Room Temperature ◽  
Az31 Alloy ◽  
Deformation Mechanisms ◽  
Az31 Mg Alloy ◽  
Deformation Features ◽  
Contrast Analysis ◽  
Observation Results

The mechanical properties and deformation features of AZ31-x%Sb alloys have been studied by means of the measurement of the ultimate tensile properties (UTS) and TEM observation. Results show that the UTS of AZ31 alloy is effectively enhanced to 297 MPa from 222 MPa, by additions of 0.84% Sb element, at room temperature, and the ultimate tensile strength of the alloy is still maintained up to 189MPa as temperature elevated to 200°C. Contrast analysis shows that the deformation mechanisms of AZ31-0.84%Sb alloy are twins and dislocations activated on basal and non-basal planes. The alloy displays the different deformation features at different deformation conditions.

Effect of Mo and Bi on Mechanical Properties of Zr-Fe-Cr Alloy at Room Temperature

2013 ◽  
Author(s):  
B. F. Luan ◽  
L. Q. Yang ◽  
T. G. Wei ◽  
K. L. Murty ◽  
C. S. Long ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Electron Microscope ◽  
Ultimate Tensile Strength ◽  
Yield Strength ◽  
Room Temperature ◽  
Mechanical Performance ◽  
Microstructure Observation ◽  
Scanning Electron ◽  
Zr Alloy

To investigate the effects of Mo and Bi on mechanical properties of a Zr-Fe-Cr alloy at room temperature, seven Zr-Fe-Cr-Mo-Bi alloys with different compositions were designed. They were subjected to a series of rolling processes and heat treatments, and then sampled to measure mechanical properties by hardness and tensile test and to characterize microstructures by scanning electron microscope (SEM) and electron channel contrast (ECC) technique. Results indicated that among them two types of Zr-Fe-Cr-Mo-Bi alloys achieve the designed goals on mechanical properties and have the following advantages: (i) the hardness of the alloys, up to 334HV after annealing, is 40% higher than traditional Zr-4. (ii) The yield strength (YS) and ultimate tensile strength (UTS) of the alloys are 526 MP a and 889 MP a after hot rolling and annealing, markedly higher than the traditional Zr alloy. (iii) Good plasticity of the new Zr-Fe-Cr-Mo-Bi alloy is obtained with about 40% elongation, which is greatly higher than the Zr-Fe-Cr-Mo alloy thanks to the addition of Bi offsetting the disadvantage of addition Mo. Furthermore, according to observations of the microstructure observation, the reasons of the effect of the Mo and Bi elements on the mechanical performance of Zr-Fe-Cr alloy were studied and discussed.

Microstructure and Mechanical Properties of Mg96Y3Zn1 Alloy Processed by Equal Channel Angular Pressing

2011 ◽  
Vol 682 ◽  
pp. 49-54
Author(s):  
Bin Chen ◽  
Chen Lu ◽  
Dong Liang Lin ◽  
Xiao Qin Zeng
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Yield Strength ◽  
Tensile Test ◽  
Equal Channel Angular Pressing ◽  
Ultrafine Grains ◽  
Angular Pressing ◽  
Average Grain Size

The Mg96Y3Zn1 alloy processed by equal channel angular pressing has been investigated. It was found that the Mg96Y3Zn1 alloy processed by ECAP obtained ultrafine grains and exhibits excellent mechanical properties. After ECAP, the average grain size of Mg96Y3Zn1 alloy refined to about 400 nm. The highest strengths with yield strength of 381.45MPa and ultimate tensile strength of 438.33MPa were obtained after 2 passes at 623K. It was found that cracks were preferentially initiated and propagated in the interior of X-phase during the tensile test. As a result, the elongation of alloy is decreased with pass number increasing.

scholarly journals Kearns texture parameters, mechanical properties and damageability of titanium sheet after alternating bending

2021 ◽  
Vol 22 (3) ◽  
pp. 543-550
Author(s):  
V.V. Usov ◽  
N.M. Shkatulyak ◽  
O.S. Savchuk ◽  
N.I. Rybak
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Ultimate Tensile Strength ◽  
Yield Stress ◽  
Rolling Direction ◽  
Initial State ◽  
Texture Parameters ◽  
Experimental Values ◽  
Alternating Bending

This work aims to determine the Kearns texture parameters and evaluate on their basis the elastic moduli, mechanical properties (ultimate tensile strength, conditional yield stress), as well as damageability parameters of the sheets commercial titanium (CT-grade 1: 0.04% Fe; 0.015% C; 0.05% N 0.05% c; 0.009% H)  as delivered after rolling and annealing at 840°C (original sheet) and further alternating bending (AB) in the amount of 0.5; 1, 3 and 5 cycles. Damageability parameters characterizing damage accumulation were determined from the elastic modulus change after the above-mentioned number of AB cycles relative to the values ​​of the elastic modulus in different directions of the original sheet of the studied titanium. The elastic constants of the single crystal and the Kearns texture parameters were used to estimate the elastic modulus in the rolling direction (RD) and transverse direction (TD) of the original sheet, and sheets after an above number of AB cycles. The deviation of the calculated and experimental values ​​of the elastic modulus did not exceed 5%. The deviation of the calculated and experimental values of the ultimate tensile strength and yield stress in the RD and TD both in the initial state and after the corresponding number cycles of the AB did not exceed 10%.

Reinforcing Inconel 718 Superalloy by Nano-TiC Particles in Selective Laser Melting

2015 ◽  
Author(s):  
Yachao Wang ◽  
Jing Shi ◽  
Yun Wang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Additive Manufacturing ◽  
Ultimate Tensile Strength ◽  
Yield Stress ◽  
Selective Laser Melting ◽  
Inconel 718 ◽  
Reinforcement Particle ◽  
Manufacturing Processes ◽  
Laser Melting

Metal components produced by additive manufacturing processes usually have inferior properties and performances as compared with the counterparts by the traditional forming and machining processes. To close the gap, the metal matrix can be strengthened by adding reinforcement particles in additive manufacturing processes. This research presents the fabrication of nano-TiC reinforced Inconel 718 composites using selective laser melting (SLM). Tensile and wear performance tests are conducted to evaluate the mechanical properties of the formed composites. It is discovered that the composites exhibit improved mechanical properties in terms of ultimate tensile strength and yield stress. Compared with the pure Inconel 718 specimens by SLM, the ultimate tensile strength and yield stress of the reinforced Inconel 718 increase by 207 MPa and 204 MPa, respectively, with 0.5 wt.% addition of nano-TiC particle. Smaller increases are observed with 0.25 wt.% and 1.0 wt.% nano-TiC additions. On the other hand, the addition of nano-TiC particles decreases the ductility of Inconel 718. To investigate the strengthening mechanism of nano reinforcement particles in SLM, the microstructures with different levels of nano-TiC particles are observed. The results indicate that the microstructure of Inconel 718 is remarkably refined by the TiC particles, and the reinforcement particle significantly impede the growth of columnar grain in the solidification process.

Mechanical Properties of an Al-Mg-Sc Alloy Subjected to Intense Plastic Straining

2010 ◽  
Vol 638-642 ◽  
pp. 1952-1958 ◽  
Author(s):  
Rustam Kaibyshev ◽  
Elena Avtokratova ◽  
O.S. Sitdikov
Keyword(s):  
Mechanical Properties ◽  
Cold Rolling ◽  
Yield Stress ◽  
Room Temperature ◽  
Total Elongation ◽  
Warm Rolling ◽  
Ultimate Stress ◽  
Angular Pressing ◽  
Ultrafine Grained ◽  
High Reduction

Effect of intense plastic straining on rollability and service properties of an Al-6%Mg-0.3%Sc alloy was examined. Ultrafine-grained structure (UFG) was produced by equal-channel angular pressing (ECAP) to a strain of 8 at a temperature of 325oC. The formation of UFG structure resulted in increase in the yield stress from 223 MPa to 285 MPa and ultimate stress from 350 MPa to 389 MPa in comparison with initial hot extruded condition. Total elongation slightly decreased from 33% to 29%. After ECAP, the material was subjected to cold and isothermal warm rolling. The formation of UFG structure resulted in enhanced rollability of the present alloy at room temperature. Cold rolling with high reduction provides the development of heavily deformed microstructure with high dislocation density, while the isothermal warm rolling does not remarkably affect the microstructure produced by ECAP. The mechanical properties after ECAP and ECAP with subsequent isothermal rolling were roughly similar. In contrast, cold rolling to the same strain resulted in significant increase of yield stress (495 MPa) and ultimate stress (536 MPa). Total elongation attained was 13%.

Sign in / Sign up

Export Citation Format

Share Document