scholarly journals Ecofriendly and innovative processing of hemp hurds fibers for tissue and towel paper

BioResources ◽  
2019 ◽  
Vol 15 (1) ◽  
pp. 706-720
Author(s):  
Ved Naithani ◽  
Preeti Tyagi ◽  
Hasan Jameel ◽  
Lucian A. Lucia ◽  
Lokendra Pal
Keyword(s):  
Water Absorption ◽  
Secondary Ion Mass Spectrometry ◽  
Chemical Properties ◽  
Dry Mass ◽  
High Yield ◽  
Pulp Fibers ◽  
Paper Properties ◽  
Hemp Fibers ◽  
Tissue Paper ◽  
Hardwood Pulp

An innovative approach for preparing hemp fibers from hemp hurds for use in tissue and towel grades of paper is described. Hemp hurds are a low value by-product of industrial hemp processing that are generally used for animal bed litter. Tissue paper was fabricated from hemp hurd fibers by following three pulping processes: autohydrolysis (hydrothermal), sodium carbonate-based defibration, and high yield kraft pulping, and benchmarked against hardwood pulp. To meet industrial standards, hardwood and hemp pulp fibers were mixed at a dry mass ratio of 75:25, from which tissue paper sheets were prepared. Desirable tissue paper properties, such as water absorption, burst resistance, softness, and tensile strength (dry and wet), were measured and compared. Characterization of morphological and chemical properties of tissue handsheets was conducted with SEM and time-of-flight-secondary ion mass spectrometry (ToF-SIMS). The combined kraft pulped hardwood and autohydrolyzed hemp pulp fibers displayed improvements in tensile index, burst resistance, and softness of tissue handsheets compared to only kraft hardwood pulp handsheets without adversely impacting water absorption. Hardwood fibers showed a sparse distribution of surface lignin compared to hemp fibers using the same defibration. This technology can lead to a variety of eco-friendly tissue paper products that are not only highly energy efficient, but avoid harsh chemical processing.

Refining of High-Yield Wood Pulp

1973 ◽  
Vol 31 ◽  
pp. 54-55
Author(s):  
Russell A. Parham
Keyword(s):  
Cell Wall ◽  
Wood Fiber ◽  
High Yield ◽  
Pulp Fibers ◽  
High Quality ◽  
Chemical Methods ◽  
Paper Properties ◽  
Intercellular Matrix ◽  
Negative Effect ◽  
Selection Of

As the supply of wood for paper and other wood fiber products constantly dwindles, the ensuing economic situation demands that wood pulping procedures be modified to provide higher yields of usable wood substance. Mechanical, semichemical, and strictly chemical methods are presently employed to reduce wood to its fibrous components. However, use of pulp fibers for high quality papers requiring whiteness or other specific attributes limits the selection of suitable pulping routes. Essentially, for quality products, it is the residual wood lignin — the intercellular matrix and cell wall encrustant (commonly 25-30% of the wood) — that is largely removed, since it exerts a general negative effect on most paper properties. Resultant pulp yields are usually in the range of 55-60%, also reflecting the loss of some wood carbohydrates that are intimately associated with the lignin structure.

scholarly journals EFFECT OF ADDITION OF DEINKED PULP TO BLEACHED KRAFT PULP ON TISSUE PAPER PROPERTIES

Wood Research ◽  
2021 ◽  
Vol 66 (3) ◽  
pp. 505-516
Author(s):  
Monika Stankovská ◽  
Mária Fišerová ◽  
Juraj Gigac ◽  
Elena Opálená
Keyword(s):  
Water Absorption ◽  
Kraft Pulp ◽  
Kraft Pulps ◽  
Initial Water ◽  
Paper Properties ◽  
High Brightness ◽  
Tissue Paper ◽  
Tensile Index ◽  
Bleached Kraft Pulp ◽  
Eucalyptus Kraft Pulp

The influence of addition of deinked pulps with low and high brightness to bleached eucalyptus and pine kraft pulps on functional tissue paper properties was studied. Deinked pulps with low and high brightness had some different functional properties. Deinked pulp with high brightness has higher bulk, porosity, water absorption after immersion, initial water absorption, bulk softness as well as brightness. On the contrary, the difference in relative bonded area and porosity e between deinked pulps with low and high brightness was moderate. The mixed pulps laboratory pulp sheets from bleached eucalyptus kraft pulp or bleached pine kraft pulp with addition of 20, 40 and 80% of deinked pulp with low brightness or deinked pulp with high brightness were prepared. The addition of the deinked pulp with high or low brightness to bleached kraft pulp leads to increasing of bulk, bulk softness as well as high water absorption after immersion and initial water absorption. The tensile index rapidly decreased by the addition of deinked pulps with high brightness to bleached eucalyptus and pine kraft pulps. Similarly, the addition of deinked pulp with low brightness to bleached pine kraft pulp led to rapid decreasing of tensile index. On contrary, with the addition of deinked pulp with low brightness to eucalyptus kraft pulp, the decreasing of tensile index was less pronounced. Mixed pulp from bleached eucalyptus kraft pulp with a small content of deinked pulp with low brightness with functional properties suitable for production of tissue papers was found as optimal.

The effect of sugar beet fiber addition on the chemical properties of tortilla chips

2012 ◽  
pp. 385-388 ◽  
Author(s):  
Azadeh Saadatmandi ◽  
Mohammad Elahi ◽  
Reza Farhoosh ◽  
Mahdi Karimi
Keyword(s):  
Sugar Beet ◽  
Water Absorption ◽  
Protein Content ◽  
Chemical Properties ◽  
Absorption Capacity ◽  
Ash Content ◽  
Oil Absorption ◽  
Water Absorption Capacity ◽  
Overall Acceptability ◽  
Tortilla Chips

The incorporation of sugar beet fiber (0–5%) to tortilla chips and the effects on the chemical and sensory properties were studied. Addition of sugar beet fiber (SBF) led to an increasing of water absorption capacity, ash content and darkness while lowering the protein content and oil absorption. Sensory evaluation showed that the overall acceptability of tortilla chips reduces if adding more than 2% SBF.

scholarly journals Whole cell-based catalyst for enzymatic production of the osmolyte 2-O-α-glucosylglycerol

2021 ◽  
Vol 20 (1) ◽  
Author(s):  
Katharina N. Schwaiger ◽  
Monika Cserjan-Puschmann ◽  
Gerald Striedner ◽  
Bernd Nidetzky
Keyword(s):  
Specific Activity ◽  
Dry Mass ◽  
High Yield ◽  
Sucrose Phosphorylase ◽  
Bifidobacterium Adolescentis ◽  
Enzymatic Production ◽  
Intracellular Enzyme ◽  
Whole Cell ◽  
Freeze Thaw ◽  
Thaw Cycle

Abstract Background Glucosylglycerol (2-O-α-d-glucosyl-sn-glycerol; GG) is a natural osmolyte from bacteria and plants. It has promising applications as cosmetic and food-and-feed ingredient. Due to its natural scarcity, GG must be prepared through dedicated synthesis, and an industrial bioprocess for GG production has been implemented. This process uses sucrose phosphorylase (SucP)-catalyzed glycosylation of glycerol from sucrose, applying the isolated enzyme in immobilized form. A whole cell-based enzyme formulation might constitute an advanced catalyst for GG production. Here, recombinant production in Escherichia coli BL21(DE3) was compared systematically for the SucPs from Leuconostoc mesenteroides (LmSucP) and Bifidobacterium adolescentis (BaSucP) with the purpose of whole cell catalyst development. Results Expression from pQE30 and pET21 plasmids in E. coli BL21(DE3) gave recombinant protein at 40–50% share of total intracellular protein, with the monomeric LmSucP mostly soluble (≥ 80%) and the homodimeric BaSucP more prominently insoluble (~ 40%). The cell lysate specific activity of LmSucP was 2.8-fold (pET21; 70 ± 24 U/mg; N = 5) and 1.4-fold (pQE30; 54 ± 9 U/mg, N = 5) higher than that of BaSucP. Synthesis reactions revealed LmSucP was more regio-selective for glycerol glycosylation (~ 88%; position O2 compared to O1) than BaSucP (~ 66%), thus identifying LmSucP as the enzyme of choice for GG production. Fed-batch bioreactor cultivations at controlled low specific growth rate (µ = 0.05 h−1; 28 °C) for LmSucP production (pET21) yielded ~ 40 g cell dry mass (CDM)/L with an activity of 2.0 × 104 U/g CDM, corresponding to 39 U/mg protein. The same production from the pQE30 plasmid gave a lower yield of 6.5 × 103 U/g CDM, equivalent to 13 U/mg. A single freeze–thaw cycle exposed ~ 70% of the intracellular enzyme activity for GG production (~ 65 g/L, ~ 90% yield from sucrose), without releasing it from the cells during the reaction. Conclusions Compared to BaSucP, LmSucP is preferred for regio-selective GG production. Expression from pET21 and pQE30 plasmids enables high-yield bioreactor production of the enzyme as a whole cell catalyst. The freeze–thaw treated cells represent a highly active, solid formulation of the LmSucP for practical synthesis.

Investigation of unsaturated polyester composites reinforced by aspen high-yield pulp fibers

2011 ◽  
Vol 33 (2) ◽  
pp. 169-177 ◽  
Author(s):  
Yicheng Du ◽  
Ning Yan ◽  
Mark T. Kortschot
Keyword(s):  
Unsaturated Polyester ◽  
High Yield ◽  
Pulp Fibers ◽  
Polyester Composites

scholarly journals A Review on Cementitious Materials Including Municipal Solid Waste Incineration Bottom Ash (MSWI-BA) as Aggregates

Buildings ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 179
Author(s):  
Jad Bawab ◽  
Jamal Khatib ◽  
Said Kenai ◽  
Mohammed Sonebi
Keyword(s):  
Municipal Solid Waste ◽  
Water Absorption ◽  
Solid Waste ◽  
Bottom Ash ◽  
Chemical Properties ◽  
Waste Incineration ◽  
Treatment Method ◽  
Cementitious Materials ◽  
Municipal Solid Waste Incineration ◽  
Municipal Solid Wastes

Waste management is a vital environmental issue in the world today. Municipal solid wastes (MSWs) are discarded in huge quantities on a daily basis and need to be well controlled. Incineration is a common method for reducing the volume of these wastes, yet it produces ashes that require further assessment. Municipal solid waste incineration bottom ash (MSWI-BA) is the bulk byproduct of the incineration process and has the potential to be used in the construction sector. This paper offers a review of the use of MSWI-BA as aggregates in cementitious materials. With the growing demand of aggregates in cementitious materials, MSWI-BA is considered for use as a partial or full alternative. Although the physical and chemical properties of MSWI-BA are different than those of natural aggregates (NA) in terms of water absorption, density, and fineness, they can be treated by various methods to ensure suitable quality for construction purposes. These treatment methods are classified into thermal treatment, solidification and stabilization, and separation processes, where this review focuses on the techniques that reduce deficiencies limiting the use of MSWI-BA as aggregates in different ways. When replacing NA in cementitious materials, MSWI-BA causes a decrease in workability, density, and strength. Moreover, they cause an increase in water absorption, air porosity, and drying shrinkage. In general, the practicality of using MSWI-BA in cementitious materials is mainly influenced by its treatment method and the replacement level, and it is concluded that further research, especially on durability, is required before MSWI-BA can be efficiently used in the production of sustainable cementitious materials.

scholarly journals Soybean waste in particleboard production

2018 ◽  
Vol 42 (2) ◽  
pp. 186-194 ◽  
Author(s):  
Evelyn Hoffmamm Martins ◽  
Alan Pereira Vilela ◽  
Rafael Farinassi Mendes ◽  
Lourival Marin Mendes ◽  
Lívia Elisabeth Vasconcellos de Siqueira Brandão Vaz ◽  
...  
Keyword(s):  
Water Absorption ◽  
Water Immersion ◽  
Eucalyptus Grandis ◽  
Raw Material ◽  
Modulus Of Rupture ◽  
High Yield ◽  
Thickness Swelling ◽  
Randomized Design ◽  
Completely Randomized Design ◽  
Hybrid Eucalyptus

ABSTRACT Brazil is the second largest soybean producer in the world, with a yield of around 96.2 million tons per crop. This high yield leads to a great amount of waste resulting from soybean cultivation, which can reach approximately 41 million tons of waste per year. This material has lignocellulosic properties, which may enable its use as a raw material for particleboard production. Therefore, the objective of this study was to evaluate the use of soybean pods in particleboard production. For particleboard manufacture, wood of the hybrid Eucalyptus urophylla and Eucalyptus grandis was used, added with soybean pods, at proportions of 0%, 25%, 50%, 75% and 100%. For particleboard evaluation, a completely randomized design was used, with five treatments and three replicates, using linear regression and the Scott-Knott test at 5% significance for comparison among the different treatments. The properties apparent density, compaction ratio, water absorption after 2 and 24 hours, thickness swelling after 2 and 24 hours in water immersion, internal bonding, modulus of rupture and modulus of elasticity in bending properties were evaluated. The ratio soybean pod waste and eucalyptus particles in the panels led to an increase in water absorption values and thickness swelling, in addition to a decrease in mechanical properties. The production of panels with approximately 23% soybean pods is feasible.

scholarly journals Managment of sulphur fertilizer in forage sorghum crop cultivated in eutrophic Cambisol with alkaline pH

2019 ◽  
pp. 1258-1266 ◽  
Author(s):  
Thiago Henrique Ferreira Matos Castañon ◽  
Boanerges Freire de Aquino ◽  
Edna Maria Bonfim Silva ◽  
Izabel Maria Almeida Lima ◽  
Ana Paula Alves Barreto Damasceno
Keyword(s):  
Elemental Sulfur ◽  
Chemical Properties ◽  
Dry Mass ◽  
Alkaline Ph ◽  
Single Superphosphate ◽  
Soil Fertilization ◽  
Forage Sorghum ◽  
Randomized Design ◽  
Sulphur Fertilizer ◽  
Completely Randomized Design

The objective of this study was to analyze the effect of soil fertilization with sulfur-based fertilizers, sulfate and elemental sulfur forms on biomass production, nutrient characteristics of sorghum and soil chemical properties. The experiment was carried out in a 4 x 4 factorial scheme (four sulfur sources: single superphosphate, agricultural gypsum, elemental sulfur powder and elemental sulfur granulated with bentonite, and four sulfur doses: 0, 40, 80, 120 mgdm-3) using four replications in a completely randomized design, being cultivated in pots under greenhouse conditions. The sorghum was cultivated for a period of 51 days after emergence of the seedlings. The shoot dry mass, shoot macronutrients content, root and soil and pH of the soil were evaluated. There were interactions between sources and sulfur doses in the variables such as shoot dry mass, sulfur in the root, sulfur and calcium in the soil. Elemental sulfur (granulate) showed lower concentrations of phosphorus, sulfur and N:S ratio in the shoot. The concentrations of potassium, calcium and magnesium did not show significant differences, both for the shoot and the root. The pH of the soil was reduced depending on the sources and doses of elemental sulfur. The sources and doses of sulfur did not influence the levels of phosphorus, potassium, and magnesium in the soil. The elemental sulfur in the form of powder is the best source of sulfur for forage sorghum cultivated in soil with alkaline pH.

scholarly journals Comparison of rhizosphere soil microbial diversity of different introduced alfalfa varieties

2020 ◽  
Author(s):  
Chunhui Ma ◽  
Jiangjiao Qi ◽  
Xue Yu ◽  
Lihe Su ◽  
Tingting He ◽  
...  
Keyword(s):  
Community Structure ◽  
Fungal Community ◽  
High Throughput Sequencing ◽  
Bacterial Species ◽  
Chemical Properties ◽  
Animal Husbandry ◽  
Desert Soil ◽  
High Yield ◽  
Soil Microbial Diversity ◽  
Fungal Community Structure

Abstract Alfalfa (Medicago sativa L.) is an important forage legume in farming and animal husbandry systems. In this study, MiSeq high-throughput sequencing was applied to assess the relationship between bacterial and fungal community structures and alfalfa growth characteristics and soil physical and chemical properties induced by different cultivars alfalfa (Victoria, Kangsai, Aohan) in the grey desert soil. The results showed that the diversity of bacterial and fungal in Victoria was higher, and the bacterial diversity was significantly lower for alfalfa with Aohan than for the others, and the fungal diversity was lower for alfalfa with Kangsai than for the others. Heatmap showed that total nitrogen, fresh weight, pH and organic have significantly affect fungal community structure, whereas pH and organic carbon also significant effects on bacterial community structure. LefSe analysis showed that the growth adaptability of introduced alfalfa is mainly related to fungal and bacterial species, and the beneficial microorganisms with significant differences and relative high abundance are significantly enriched in Victoria. Pathogens with high relative abundance are mainly concentrated in Aohan alfalfa soil. Based on our findings, Victoria is the high-yield alfalfa suitable for planting in gray desert soil, while planting Kangsai and Aohan alfalfa needs probiotic for adjuvant.

Sign in / Sign up

Export Citation Format

Share Document