Variations in the synthesis of barium hexaferrite doped with iridium and its effect in the catalytic combustion of hydrocarbons

1998 ◽  
Vol 13 (6) ◽  
pp. 1637-1643 ◽  
Author(s):  
A. C. Pierre ◽  
A. Favre ◽  
N. Guilhaume
Keyword(s):  
Porous Structure ◽  
Catalytic Combustion ◽  
Catalytic Properties ◽  
Barium Hexaferrite ◽  
Metal Salts ◽  
X Ray Diffraction ◽  
X Ray ◽  
Heat Treated ◽  
Bet Analysis ◽  
Structure Phase

This paper discusses the influence of the synthesis technique on the porous structure, phase transformation, and catalytic properties of barium hexaferrite. Barium hexaferrite was synthesized by two different citrate gel methods. The first one involved metal salts, citric acid, and ammonia, while the second dispersed the same components in a polyacrylamide gel. X-ray diffraction analysis was used to determine the nature of the phase while the Brunauer, Emmett, and Teller (BET) analysis was used to study the porous structure of the material which were heat-treated at 700 °C, 900 °C, and 1200 °C. The catalytic activity of all materials in the combustion of methane was also measured.

Effect of Hydrated Metal Salts on the Coordination Product of Cobalt(II) halide and PNP Type Ligand, 2,6-bis(di-tertbutylphosphinomethyl) pyridine

2018 ◽  
Author(s):  
Tasneem Siddiquee ◽  
Abdul Goni
Keyword(s):  
Metal Salts ◽  
Molar Ratio ◽  
Pincer Complexes ◽  
Asymmetric Unit ◽  
X Ray Diffraction ◽  
Pincer Ligand ◽  
Tetrahedral Geometry ◽  
X Ray ◽  
Distorted Tetrahedral Geometry ◽  
Cobalt Center

Chemical treatment of CoX<sub>2</sub><b><sup>. </sup></b>6H<sub>2</sub>O (X = Cl, Br, I) with the potentially tridentate PNP pincer ligand 2,6-bis(di-<i>tert</i>-butylphosphinomethyl)pyridine in 1:1 molar ratio results in cobalt(II) halide-PNP pincer complexes. The effect of the hydrated metal source on molecular structure and geometry of the complexes was studied by single crystal X-ray diffraction analysis. The complexes are neutral and the cobalt center adopts a penta-coordinate system with potential atropisomerization. Within the unit cell there are two distinct molecules per asymmetric unit. One of the two phosphorus atoms in the PNP ligand was observed to be partially oxidized to phosphinoxide. Disorder in the structure reflects a mixture of square pyramidal and distorted tetrahedral geometry.

Physicochemical and Catalytic Properties of Spinels Formed by Solid-Solid Interaction Between Fe2O3and V2O5

1996 ◽  
Vol 61 (8) ◽  
pp. 1131-1140 ◽  
Author(s):  
Abd El-Aziz Ahmed Said
Keyword(s):  
Vanadium Oxide ◽  
Active Sites ◽  
Catalyst Surface ◽  
Catalytic Properties ◽  
Flow System ◽  
Oxide Catalysts ◽  
X Ray Diffraction ◽  
Selective Catalyst ◽  
X Ray ◽  
Solid Catalysts

Vanadium oxide catalysts doped or mixed with 1-50 mole % Fe3+ ions were prepared. The structure of the original samples and those calcined from 200 up to 500 °C were characterized by TG, DTA, IR and X-ray diffraction. The SBET values and texture of the solid catalysts were investigated. The catalytic dehydration-dehydrogenation of isopropanol was carried out at 200 °C using a flow system. The results obtained showed an observable decrease in the activity of V2O5 on the addition of Fe3+ ions. Moreover, Fe2V4O13 is the more active and selective catalyst than FeVO4 spinels. The results were correlated with the active sites created on the catalyst surface.

scholarly journals Stable and Metastable Phase Equilibria Involving the Cu6Sn5 Intermetallic

2021 ◽  
Author(s):  
A. Leineweber ◽  
M. Löffler ◽  
S. Martin
Keyword(s):  
Phase Equilibria ◽  
Electron Backscatter Diffraction ◽  
Metastable Phase ◽  
Stable Phase ◽  
X Ray Diffraction ◽  
X Ray ◽  
Heat Treated ◽  
Ordered Phases ◽  
Backscatter Diffraction ◽  
Kinetics Of

Abstract Cu6Sn5 intermetallic occurs in the form of differently ordered phases η, η′ and η′′. In solder joints, this intermetallic can undergo changes in composition and the state of order without or while interacting with excess Cu and excess Sn in the system, potentially giving rise to detrimental changes in the mechanical properties of the solder. In order to study such processes in fundamental detail and to get more detailed information about the metastable and stable phase equilibria, model alloys consisting of Cu3Sn + Cu6Sn5 as well as Cu6Sn5 + Sn-rich melt were heat treated. Powder x-ray diffraction and scanning electron microscopy supplemented by electron backscatter diffraction were used to investigate the structural and microstructural changes. It was shown that Sn-poor η can increase its Sn content by Cu3Sn precipitation at grain boundaries or by uptake of Sn from the Sn-rich melt. From the kinetics of the former process at 513 K and the grain size of the η phase, we obtained an interdiffusion coefficient in η of (3 ± 1) × 10−16 m2 s−1. Comparison of this value with literature data implies that this value reflects pure volume (inter)diffusion, while Cu6Sn5 growth at low temperature is typically strongly influenced by grain-boundary diffusion. These investigations also confirm that η′′ forming below a composition-dependent transus temperature gradually enriches in Sn content, confirming that Sn-poor η′′ is metastable against decomposition into Cu3Sn and more Sn-rich η or (at lower temperatures) η′. Graphic Abstract

Facile Solid State Method Route Synthesis and Enhance Visible Light Activities of BiVO4 by Doping Co

2016 ◽  
Vol 703 ◽  
pp. 316-320
Author(s):  
Hai Feng Chen ◽  
Jing Ling Hu ◽  
Bing Xu
Keyword(s):  
Solid State ◽  
Visible Light ◽  
Catalytic Effect ◽  
Catalytic Properties ◽  
Raw Materials ◽  
X Ray Diffraction ◽  
Solid State Method ◽  
Illumination Time ◽  
X Ray ◽  
State Method

Using NH4VO3, Bi (NO3)3•5H2O and Co (NO3)2•6H2O as raw materials, Co doped BiVO4 (Co/BiVO4) photocatalysts were successfully prepared by solid state method. And the photo catalytic properties were test in this work. Crystal structures of these samples were characterized by X-ray diffraction (XRD). The Methyl Orange (MO) was simulated as the sewage under the visible light to explorer the influence of the illumination time and the mass of photocatalyst. The visible-light absorption spectrum of BiVO4 was broadening with doping Co. It was found that the Co/BiVO4 had higher photocatalytic activity than pure BiVO4 .The reason of enhanced catalytic effect also had been analyzed and discussed in the article.

PREPARATION OF ANTIMONY-PLATINUM SURFACE ALLOY ELECTRODE BY ATOM DIFFUSION IN THE SOLID PHASE

2006 ◽  
Vol 20 (25n27) ◽  
pp. 3999-4004
Author(s):  
HIROSHI MATSUI ◽  
KAZUFUMI WATANABE
Keyword(s):  
Diffraction Pattern ◽  
Low Temperatures ◽  
Solid Phase ◽  
Electrochemical Measurement ◽  
X Ray Diffraction ◽  
Platinum Surface ◽  
X Ray ◽  
Atom Diffusion ◽  
Heat Treated ◽  
Titanium Substrates

Antimony-platinum bilayers were prepared on titanium substrates by the two-step electrodeposition in the usual baths, and then surface alloys were formed by the atom diffusion in the solid phase. The simple antimony layer was little influenced by the substrate in both the measurements of X-ray diffraction and the i - E characteristic in a sulfuric acid solution. Regarding the bilayers, the catalytic activity in hydrogen evolution reaction was very sensitive to the presence of platinum, while the hydrogen adsorbability was quite insensitive. An interaction between antimony and platinum was confirmed by the appearance of a new dissolution wave in the electrochemical measurement and the occurrence of a new diffraction in the X-ray diffraction pattern after the heat-treatment of about 400°C. Although the new diffraction disagreed with any of the reported alloys, clear diffraction pattern of PtSb 2 alloy was observed, when the bilayers were heat-treated at about 600°C for one hour. Considering the penetration depth of X-ray, the alloying of antimony and platinum seems to occur also at low temperatures at least at the top surface.

Preparation and Application of Lead Dioxide Electrode for Zinc Electrolysis

2013 ◽  
Vol 785-786 ◽  
pp. 1125-1129
Author(s):  
Xiao Yong Yang ◽  
Pei Xian Zhu ◽  
Yun Sen Si
Keyword(s):  
Surface Characterization ◽  
Catalytic Properties ◽  
Lead Dioxide ◽  
Manufacturing Cost ◽  
X Ray Diffraction ◽  
Simulation Test ◽  
X Ray ◽  
Zinc Smelter ◽  
Lead Dioxide Electrode

According to the process of anodic oxygen evolution in sulfate system for zinc electrolysis,Ti-base lead dioxide electrode can be prepared to use in this case.The surface characterization of the electrode was studied by Scanning electron microscopy(SEM) and X-ray diffraction(XRD).The electrode lifetime was tested in 1mol/L H2SO4solution at 60°C,and the electro-catalytic properties was examined by polarization curves.Then these samples was enlarged and simulation test was conducted at Mengzi marriage zinc smelter in Yunnan.The results show that the electro-catalytic properties is better and the electrodes lifetime is longer compared to the traditional lead electrode.Moreover,it has a significant effect in reducing energy consumption, manufacturing cost and improving the production and grade of zinc.

Hardening of Selective Laser Melted M2 Steel

2021 ◽  
Author(s):  
Mei Yang ◽  
Yishu Zhang ◽  
Haoxing You ◽  
Richard Smith ◽  
Richard D. Sisson
Keyword(s):  
Heat Treatment ◽  
High Speed ◽  
Cutting Tools ◽  
High Speed Steel ◽  
High Hardness ◽  
Steel Part ◽  
X Ray Diffraction ◽  
X Ray ◽  
Heat Treated ◽  
Near Net Shape

Abstract Selective laser melting (SLM) is an additive manufacturing technique that can be used to make the near-net-shape metal parts. M2 is a high-speed steel widely used in cutting tools, which is due to its high hardness of this steel. Conventionally, the hardening heat treatment process, including quenching and tempering, is conducted to achieve the high hardness for M2 wrought parts. It was debated if the hardening is needed for additively manufactured M2 parts. In the present work, the M2 steel part is fabricated by SLM. It is found that the hardness of as-fabricated M2 SLM parts is much lower than the hardened M2 wrought parts. The characterization was conducted including X-ray diffraction (XRD), optical microscopy, Scanning Electron Microscopy (SEM), and energy dispersive X-ray spectroscopy (EDS) to investigate the microstructure evolution of as-fabricated, quenched, and tempered M2 SLM part. The M2 wrought part was heat-treated simultaneously with the SLM part for comparison. It was found the hardness of M2 SLM part after heat treatment is increased and comparable to the wrought part. Both quenched and tempered M2 SLM and wrought parts have the same microstructure, while the size of the carbides in the wrought part is larger than that in the SLM part.

scholarly journals Solvothermally derived Me2(H2O)4(5SSA)3·DMF and Me2(H2O)4(4NSA)2·DMF: Application as Biginelli reaction catalysts

Chemija ◽  
2019 ◽  
Vol 30 (2) ◽  
Author(s):  
Andrius Laurikėnas ◽  
Fatma Yalçin ◽  
Robertas Žilinskas ◽  
Ayse Uztetik Morkan ◽  
Albinas Žilinskas ◽  
...  
Keyword(s):  
Solvothermal Synthesis ◽  
Catalytic Properties ◽  
Inorganic Compounds ◽  
Biginelli Reaction ◽  
Xrd Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Hybrid Compounds ◽  
Phase And Chemical Composition ◽  
Scanning Electron

The solvothermal synthesis between Me(NO3)x ∙ yH2O (Mex+ = Fe3+, Ni2+, Mn2+, Co2+, Cu2+) and respectively 4-nitrosalycilic (4NSA) and 5-sulfosalicylic (5SSA) acids produced hybrid organic-inorganic compounds composed of Mex+ ions and organic fragments which include three different functional groups, carboxylic, hydroxyl and sulfonic, each coordinated to the Mex+ ions. The phase and chemical composition, microstructure and properties of Me2(H2O)4(5SSA)3·DMF and Me2(H2O)4(4NSA)2·DMF (DMF – dimethylformamide) hybrid compounds were evaluated and discussed. The synthesised materials were characterised by X-ray diffraction (XRD) analysis, scanning electron microscopy (SEM) and nuclear magnetic resonance (NMR) spectroscopy. The catalytic properties of the obtained compounds were also investigated.

X-Ray Diffraction Analysis on Crystallite Development of Nanostructured Aluminium

2006 ◽  
Vol 118 ◽  
pp. 53-58
Author(s):  
Elisabeth Meijer ◽  
Nicholas Armstrong ◽  
Wing Yiu Yeung
Keyword(s):  
Crystallite Size ◽  
Room Temperature ◽  
Annealing Temperature ◽  
Equal Channel Angular Extrusion ◽  
Line Broadening ◽  
X Ray Diffraction ◽  
Integral Breadth ◽  
X Ray ◽  
Heat Treated ◽  
Diffraction Peaks

This study is to investigate the crystallite development in nanostructured aluminium using x-ray line broadening analysis. Nanostructured aluminium was produced by equal channel angular extrusion at room temperature to a total deformation strain of ~17. Samples of the extruded metal were then heat treated at temperatures up to 300oC. High order diffraction peaks were obtained using Mo radiation and the integral breadth was determined. It was found that as the annealing temperature increased, the integral breadth of the peak reflections decreased. By establishing the modified Williamson-Hall plots (integral breadth vs contract factor) after instrumental correction, it was determined that the crystallite size of the metal was maintained ~80 nm at 100oC. As the annealing temperature increased to 200oC, the crystallite size increased to ~118 nm. With increasing annealing temperature, the hardness of the metal decreased from ~60 HV to ~45 HV.

Sign in / Sign up

Export Citation Format

Share Document