Variations in Mechanical Properties of Wood Plates Due Fluctuations on Relative Humidity of Air

2012 ◽  
Vol 1372 ◽  
Author(s):  
J. A. Torres ◽  
M. De Icaza ◽  
R. R. Boullosa
Keyword(s):  
Mechanical Properties ◽  
Relative Humidity ◽  
Shear Modulus ◽  
Natural Frequencies ◽  
Element Model ◽  
Quantitative Information ◽  
Musical Instruments ◽  
Similar Frequency ◽  
Natural Variations ◽  
Set Up

ABSTRACTOften, mechanical properties of wood plates are accurately approximated through orthotropic characterization. However, the numerical values may show considerable variations in the case of real wood plates immersed in fluctuant environmental conditions, especially if the relative humidity of air (RH) is changing. Problems arising from the natural variations in RH have been reported on making musical instruments. In this work, the influence of changing RH on the mechanical properties of a guitar’s top plate (clamped on its contour) has been measured. Vibratory responses of the plate were experimentally obtained, through forced vibration, while data were recorded for several RH values, without any alteration in the experimental set-up devices. The six lowest natural frequencies of the structure were extracted from peaks detected in the responses. Natural frequencies depend on mass distribution and mechanical properties of the structure. For the highest sensed RH (67 %), each natural frequency of the plate decreased at least in 11 Hz compared with reference values measured at the lowest sensed RH (53 %). To determine the connection between the shift in natural frequencies and the changes in the wood elastic and shear modulus, a finite element model of the plate was performed. It was useful calculating natural frequencies through simulated modal analyses. Elastic and shear modulus were handled to match simulated results with experimental natural frequencies recorded for a RH=53% level. These elastic moduli must be decreased around 10 % to obtain a similar frequency decrease in the experimental natural frequencies obtained under a RH=67% level. The experimental results show quantitative information on an interaction scarcely researched, that is, the modification on mechanical properties of wood plates induced by RH variations. Sensed changes due this wood-air interaction are responsible of a modification in the behavior of musical instruments, as guitars and violins.

The Study on Dynamic Characteristics for Heald Frame Designed by New Type Composite of Carbon-Fibre

2013 ◽  
Vol 804 ◽  
pp. 353-357
Author(s):  
Hai Fei Qiu ◽  
Yi Xuan Wang ◽  
Song Lin Wu
Keyword(s):  
Carbon Fibre ◽  
Dynamic Characteristics ◽  
Natural Frequencies ◽  
Lightweight Design ◽  
Element Model ◽  
Vibration Modes ◽  
Vibration Resistance ◽  
New Type ◽  
Set Up ◽  
Type Composite

For reducing heald frames vibration and noise in the process of weaving, composite of Carbon-Fibre was applied to it, and three methods of lay up for laminate was designed in the paper. Finite element model of the heald frame was set up, and element shell 181 was used to simulate different layers of the composite material, then some important natural frequencies and vibration modes were calculated, and the results of that was compared with another heald frame made of aluminium alloy. The analysis result indicated that, the second method for laying had an optimum dynamic characteristics, based on that, fundamental frequency of the heald frame was increased by 19.48Hz, and self-weight of it was lightened about 26.82%. In results, lightweight design of the heald frame was come true, at the same time, vibration resistance of it was also strengthened effectively.

scholarly journals Elucidation of Regional Mechanical Properties of Brain Tissues Based on Cell Density

2021 ◽  
Vol 18 (3) ◽  
pp. 611-622
Author(s):  
Chi Zhang ◽  
Long Qian ◽  
Hongwei Zhao
Keyword(s):  
Mechanical Properties ◽  
Cerebral Cortex ◽  
Shear Modulus ◽  
Brain Tissue ◽  
Unit Area ◽  
Neuronal Cell ◽  
Occipital Lobe ◽  
Element Model ◽  
Cellular Density ◽  
Neuronal Cell Bodies

AbstractResearch on the mechanical properties of brain tissue has received extensive attention. However, most of the current studies have been conducted at the phenomenological level. In this study, the indentation method was used to explore the difference in local mechanical properties among different regions of the porcine cerebral cortex. Further, hematoxylin-eosin and immunofluorescence staining methods were used to determine the correlation between the cellular density at different test points and mechanical properties of the porcine cerebral cortex. The frontal lobe exhibited the strongest viscosity. The temporal lobe displayed the lowest sensitivity to changes in the indentation speed, and the occipital lobe exhibited the highest shear modulus. Additionally, the shear modulus of different areas of the cerebral cortex was negatively correlated with the total number of local cells per unit area and positively correlated with the number of neuronal cell bodies per unit area. Exploration of the mechanical properties of the local brain tissue can provide basic data for the establishment of a finite element model of the brain and mechanical referential information for the implantation position of brain chips.

Mechanical properties of FeAlSi powders prepared by mechanical alloying from different initial feedstock materials

2019 ◽  
Vol 107 (2) ◽  
pp. 207 ◽  
Author(s):  
Jaroslav Čech ◽  
Petr Haušild ◽  
Miroslav Karlík ◽  
Veronika Kadlecová ◽  
Jiří Čapek ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Mechanical Alloying ◽  
Young’S Modulus ◽  
Milling Time ◽  
Young's Modulus ◽  
Element Model ◽  
X Ray Diffraction ◽  
X Ray ◽  
Powder Particles ◽  
Complete Homogenization

FeAl20Si20 (wt.%) powders prepared by mechanical alloying from different initial feedstock materials (Fe, Al, Si, FeAl27) were investigated in this study. Scanning electron microscopy, X-ray diffraction and nanoindentation techniques were used to analyze microstructure, phase composition and mechanical properties (hardness and Young’s modulus). Finite element model was developed to account for the decrease in measured values of mechanical properties of powder particles with increasing penetration depth caused by surrounding soft resin used for embedding powder particles. Progressive homogenization of the powders’ microstructure and an increase of hardness and Young’s modulus with milling time were observed and the time for complete homogenization was estimated.

Effect of Dynamic Crosslinking on Mechanical Properties of PP/EPDM Blends

1993 ◽  
Vol 58 (11) ◽  
pp. 2642-2650 ◽  
Author(s):  
Zdeněk Kruliš ◽  
Ivan Fortelný ◽  
Josef Kovář
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Shear Modulus ◽  
High Impact ◽  
Necessary Condition ◽  
Step Method ◽  
Melt Mixing ◽  
One Step ◽  
High Impact Strength ◽  
Dynamic Curing

The effect of dynamic curing of PP/EPDM blends with sulfur and thiuram disulfide systems on their mechanical properties was studied. The results were interpreted using the knowledge of the formation of phase structure in the blends during their melt mixing. It was shown, that a sufficiently slow curing reaction is necessary if a high impact strength is to be obtained. Only in such case, a fine and homogeneous dispersion of elastomer can be formed, which is the necessary condition for high impact strength of the blend. Using an inhibitor of curing in the system and a one-step method of dynamic curing leads to an increase in impact strength of blends. From the comparison of shear modulus and impact strength values, it follows that, at the stiffness, the dynamically cured blends have higher impact strength than the uncured ones.

scholarly journals Modelling of speleothems failure in the Hotton cave (Belgium). Is the failure earthquake induced?

2001 ◽  
Vol 80 (3-4) ◽  
pp. 315-321 ◽  
Author(s):  
J.F. Cadorin ◽  
D. Jongmans ◽  
A. Plumier ◽  
T. Camelbeeck ◽  
S. Delaby ◽  
...  
Keyword(s):  
Natural Frequencies ◽  
Quantitative Information ◽  
Rigid Bodies ◽  
Tensile Failure ◽  
Future Research ◽  
Geometrical Parameters ◽  
Laboratory Measurements ◽  
Ground Acceleration ◽  
Strong Ground

AbstractTo provide quantitative information on the ground acceleration necessary to break speleothems, laboratory measurements on samples of stalagmite have been performed to study their failure in bending. Due to their high natural frequencies, speleothems can be considered as rigid bodies to seismic strong ground motion. Using this simple hypothesis and the determined mechanical properties (a minimum value of 0.4 MPa for the tensile failure stress has been considered), modelling indicates that horizontal acceleration ranging from 0.3 m/s2 to 100 m/s2 (0.03 to 10g) are necessary to break 35 broken speleothems of the Hotton cave for which the geometrical parameters have been determined. Thus, at the present time, a strong discrepancy exists between the peak accelerations observed during earthquakes and most of the calculated values necessary to break speleothems. One of the future research efforts will be to understand the reasons of the defined behaviour. It appears fundamental to perform measurements on in situ speleothems.

Measurement of Young’s Modulus and Shear Modulus of Some Structures Welded Using Flux Cored Wire by Vibration Tests

2014 ◽  
Vol 216 ◽  
pp. 151-156 ◽  
Author(s):  
Liviu Bereteu ◽  
Mircea Vodǎ ◽  
Gheorghe Drăgănescu
Keyword(s):  
Shear Modulus ◽  
Arc Welding ◽  
Natural Frequencies ◽  
Free Vibrations ◽  
Vibration Modes ◽  
Cored Wire ◽  
Flux Cored Arc Welding ◽  
Longitudinal Elastic Modulus ◽  
Vibration Tests ◽  
Non Destructive

The aim of this work was to determine by vibration tests the longitudinal elastic modulus and shear modulus of welded joints by flux cored arc welding. These two material properties are characteristic elastic constants of tensile stress respectively torsion stress and can be determined by several non-destructive methods. One of the latest non-destructive experimental techniques in this field is based on the analysis of the vibratory signal response from the welded sample. An algorithm based on Pronys series method is used for processing the acquired signal due to sample response of free vibrations. By the means of Finite Element Method (FEM), the natural frequencies and modes shapes of the same specimen of carbon steel were determined. These results help to interpret experimental measurements and the vibration modes identification, and Youngs modulus and shear modulus determination.

scholarly journals Vibration characteristics of triple-gear-rotor system in compressed air energy storage under variable torque load

2021 ◽  
Vol 104 (1) ◽  
pp. 003685042098705
Author(s):  
Xinran Wang ◽  
Yangli Zhu ◽  
Wen Li ◽  
Dongxu Hu ◽  
Xuehui Zhang ◽  
...  
Keyword(s):  
Large Scale ◽  
Three Dimensional ◽  
Element Model ◽  
Rotor System ◽  
Dynamic Responses ◽  
System Response ◽  
Rotating Speed ◽  
Torque Load ◽  
Set Up ◽  
Two Stages

This paper focuses on the effects of the off-design operation of CAES on the dynamic characteristics of the triple-gear-rotor system. A finite element model of the system is set up with unbalanced excitations, torque load excitations, and backlash which lead to variations of tooth contact status. An experiment is carried out to verify the accuracy of the mathematical model. The results show that when the system is subjected to large-scale torque load lifting at a high rotating speed, it has two stages of relatively strong periodicity when the torque load is light, and of chaotic when the torque load is heavy, with the transition between the two states being relatively quick and violent. The analysis of the three-dimensional acceleration spectrum and the meshing force shows that the variation in the meshing state and the fluctuation of the meshing force is the basic reasons for the variation in the system response with the torque load. In addition, the three rotors in the triple-gear-rotor system studied show a strong similarity in the meshing states and meshing force fluctuations, which result in the similarity in the dynamic responses of the three rotors.

scholarly journals Evolution of the viscoelastic properties of painting stratigraphies: a moisture weathering and nanoindentation approach

2021 ◽  
Vol 9 (1) ◽  
Author(s):  
Mathilde Tiennot ◽  
Davide Iannuzzi ◽  
Erma Hermens
Keyword(s):  
Mechanical Properties ◽  
Relative Humidity ◽  
Cultural Heritage ◽  
Mechanical Behaviour ◽  
Viscoelastic Properties ◽  
Viscoelastic Behaviour ◽  
Storage And Loss Moduli ◽  
Heritage Studies ◽  
Paint Films ◽  
The Impact

AbstractIn this investigation on the mechanical behaviour of paint films, we use a new ferrule-top nanoindentation protocol developed for cultural heritage studies to examine the impact of repeated relative humidity variations on the viscoelastic behaviour of paint films and their mechanical properties in different paint stratigraphies through the changes in their storage and loss moduli. We show that the moisture weathering impact on the micromechanics varies for each of these pigment-oil systems. Data from the nanoindentation protocol provide new insights into the evolution of the viscoelastic properties dsue to the impact of moisture weathering on paint films.

scholarly journals Prediction of Pest Insect Appearance Using Sensors and Machine Learning

Sensors ◽  
2021 ◽  
Vol 21 (14) ◽  
pp. 4846
Author(s):  
Dušan Marković ◽  
Dejan Vujičić ◽  
Snežana Tanasković ◽  
Borislav Đorđević ◽  
Siniša Ranđić ◽  
...  
Keyword(s):  
Machine Learning ◽  
Relative Humidity ◽  
Weather Conditions ◽  
Daily Basis ◽  
Machine Learning Algorithms ◽  
Lower Percentage ◽  
Timely Manner ◽  
Proposed Model ◽  
Set Up ◽  
Accuracy Of Prediction

The appearance of pest insects can lead to a loss in yield if farmers do not respond in a timely manner to suppress their spread. Occurrences and numbers of insects can be monitored through insect traps, which include their permanent touring and checking of their condition. Another more efficient way is to set up sensor devices with a camera at the traps that will photograph the traps and forward the images to the Internet, where the pest insect’s appearance will be predicted by image analysis. Weather conditions, temperature and relative humidity are the parameters that affect the appearance of some pests, such as Helicoverpa armigera. This paper presents a model of machine learning that can predict the appearance of insects during a season on a daily basis, taking into account the air temperature and relative humidity. Several machine learning algorithms for classification were applied and their accuracy for the prediction of insect occurrence was presented (up to 76.5%). Since the data used for testing were given in chronological order according to the days when the measurement was performed, the existing model was expanded to take into account the periods of three and five days. The extended method showed better accuracy of prediction and a lower percentage of false detections. In the case of a period of five days, the accuracy of the affected detections was 86.3%, while the percentage of false detections was 11%. The proposed model of machine learning can help farmers to detect the occurrence of pests and save the time and resources needed to check the fields.

scholarly journals Corrosion of Steel Rebars in Anoxic Environments. Part II: Pit Growth Rate and Mechanical Strength

Materials ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2547
Author(s):  
Elena Garcia ◽  
Julio Torres ◽  
Nuria Rebolledo ◽  
Raul Arrabal ◽  
Javier Sanchez
Keyword(s):  
Mechanical Strength ◽  
Chloride Content ◽  
Element Model ◽  
Offshore Structures ◽  
Anoxic Environments ◽  
Electrochemical Parameters ◽  
Cathode Area ◽  
Optical Profilometer ◽  
Set Up ◽  
Corrosion Of Steel

Reinforced concrete may corrode in anoxic environments such as offshore structures. Under such conditions the reinforcement fails to passivate completely, irrespective of chloride content, and the corrosion taking place locally induces the growth of discrete pits. This study characterised such pits and simulated their growth from experimentally determined electrochemical parameters. Pit morphology was assessed with an optical profilometer. A finite element model was developed to simulate pit growth based on electrochemical parameters for different cathode areas. The model was able to predict long-term pit growth by deformed geometry set up. Simulations showed that pit growth-related corrosion tends to maximise as cathode area declines, which lower the pitting factor. The mechanical strength developed by the passive and prestressed rebar throughout its service life was also estimated. Passive rebar strength may drop by nearly 20% over 100 years, whilst in the presence of cracking from the base of the pit steel strength may decline by over 40%.

Sign in / Sign up

Export Citation Format

Share Document