Hydrogel Based Composite Materials for Chemical, Biological and Medical Sensing Applications

2007 ◽  
Vol 1010 ◽  
Author(s):  
Timothy L. Porter ◽  
Tim Vail ◽  
Jim Reed ◽  
Ray Stewart
Keyword(s):  
Gold Nanoparticles ◽  
Composite Materials ◽  
Hydrogen Fluoride ◽  
Low Cost ◽  
Medical Application ◽  
Sensing Applications ◽  
Biological Analytes

AbstractEmbedded piezoresistive microcantilever (EPM) sensors provide a tiny, low-cost, and robust platform for the detection of chemical or biological analytes. New sensing applications become potentially available as the design or synthesis of new sensing materials for EPM instruments are studies. In this study, we report on the detection of hydrogen fluoride gas (HF) in air, and in a medical application, the measurement of human hydration levels. Two sensing materials characterize these applications, thiolated gold nanoparticles in a keratin matrix (HF), and a crosslinked PVA-based hydrogel in the hydration application.

Computer simulation study about the dependence of amorphous silicon photonic waveguides efficiency on the material quality

2020 ◽  
Vol 90 (3) ◽  
pp. 30502
Author(s):  
Alessandro Fantoni ◽  
João Costa ◽  
Paulo Lourenço ◽  
Manuela Vieira
Keyword(s):  
Amorphous Silicon ◽  
High Throughput Screening ◽  
Simulation Analysis ◽  
Low Cost ◽  
Deposition Process ◽  
Large Area ◽  
Sidewall Roughness ◽  
Sensing Applications ◽  
Fabrication Defects ◽  
The Impact

Amorphous silicon PECVD photonic integrated devices are promising candidates for low cost sensing applications. This manuscript reports a simulation analysis about the impact on the overall efficiency caused by the lithography imperfections in the deposition process. The tolerance to the fabrication defects of a photonic sensor based on surface plasmonic resonance is analysed. The simulations are performed with FDTD and BPM algorithms. The device is a plasmonic interferometer composed by an a-Si:H waveguide covered by a thin gold layer. The sensing analysis is performed by equally splitting the input light into two arms, allowing the sensor to be calibrated by its reference arm. Two different 1 × 2 power splitter configurations are presented: a directional coupler and a multimode interference splitter. The waveguide sidewall roughness is considered as the major negative effect caused by deposition imperfections. The simulation results show that plasmonic effects can be excited in the interferometric waveguide structure, allowing a sensing device with enough sensitivity to support the functioning of a bio sensor for high throughput screening. In addition, the good tolerance to the waveguide wall roughness, points out the PECVD deposition technique as reliable method for the overall sensor system to be produced in a low-cost system. The large area deposition of photonics structures, allowed by the PECVD method, can be explored to design a multiplexed system for analysis of multiple biomarkers to further increase the tolerance to fabrication defects.

Bamboo Waste-based Bio-composite Substance: An application for Low-cost Construction Materials

2020 ◽  
Vol 4 (1) ◽  
pp. 41-48
Author(s):  
Teodoro Astorga Amatosa ◽  
Michael E. Loretero
Keyword(s):  
Composite Materials ◽  
Sea Water ◽  
Raw Materials ◽  
Low Cost ◽  
Construction Materials ◽  
Single Layer ◽  
High Strength ◽  
Green Technology ◽  
Experimental Medium ◽  
Natural Treatment

Bamboo is a lightweight and high-strength raw materials that encouraged researchers to investigate and explore, especially in the field of biocomposite and declared as one of the green-technology on the environment as fully accountable as eco-products. This research was to assess the technical feasibility of making single-layer experimental Medium-Density Particleboard panels from the bamboo waste of a three-year-old (Dendrocalamus asper). Waste materials were performed to produce composite materials using epoxy resin (C21H25C105) from a natural treatment by soaking with an average of pH 7.6 level of sea-water. Three different types of MDP produced, i.e., bamboo waste strip MDP (SMDP), bamboo waste chips MDP (CMDP) and bamboo waste mixed strip-chips MDP (MMDP) by following the same process. The experimental panels tested for their physical-mechanical properties according to the procedures defined by ASTM D1037-12. Conclusively, even the present study shows properties of MDP with higher and comparable to other composite materials; further research must be given better attention as potential substitute to be used as hardwood materials, especially in the production, design, and construction usage.

scholarly journals Physical and Mechanical Properties of Natural Leaf Fiber-Reinforced Epoxy Polyester Composites

Polymers ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1369
Author(s):  
Sanjeev Kumar ◽  
Lalta Prasad ◽  
Vinay Kumar Patel ◽  
Virendra Kumar ◽  
Anil Kumar ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Composite Materials ◽  
Synthetic Fibre ◽  
Low Cost ◽  
Fibre Length ◽  
Physical And Mechanical Properties ◽  
Natural Fibres ◽  
Risk Environment ◽  
Insulation Property ◽  
Natural Leaf

In recent times, demand for light weight and high strength materials fabricated from natural fibres has increased tremendously. The use of natural fibres has rapidly increased due to their high availability, low density, and renewable capability over synthetic fibre. Natural leaf fibres are easy to extract from the plant (retting process is easy), which offers high stiffness, less energy consumption, less health risk, environment friendly, and better insulation property than the synthetic fibre-based composite. Natural leaf fibre composites have low machining wear with low cost and excellent performance in engineering applications, and hence established as superior reinforcing materials compared to other plant fibres. In this review, the physical and mechanical properties of different natural leaf fibre-based composites are addressed. The influences of fibre loading and fibre length on mechanical properties are discussed for different matrices-based composite materials. The surface modifications of natural fibre also play a crucial role in improving physical and mechanical properties regarding composite materials due to improved fibre/matrix adhesion. Additionally, the present review also deals with the effect of silane-treated leaf fibre-reinforced thermoset composite, which play an important role in enhancing the mechanical and physical properties of the composites.

scholarly journals Current Trends in Polymer Based Sensors

Chemosensors ◽  
2021 ◽  
Vol 9 (5) ◽  
pp. 108
Author(s):  
Giancarla Alberti ◽  
Camilla Zanoni ◽  
Vittorio Losi ◽  
Lisa Rita Magnaghi ◽  
Raffaela Biesuz
Keyword(s):  
Chemical Structure ◽  
Low Cost ◽  
Sensing Applications ◽  
Current Trends ◽  
Manufacturing Methods ◽  
New Devices

This review illustrates various types of polymer and nanocomposite polymeric based sensors used in a wide variety of devices. Moreover, it provides an overview of the trends and challenges in sensor research. As fundamental components of new devices, polymers play an important role in sensing applications. Indeed, polymers offer many advantages for sensor technologies: their manufacturing methods are pretty simple, they are relatively low-cost materials, and they can be functionalized and placed on different substrates. Polymers can participate in sensing mechanisms or act as supports for the sensing units. Another good quality of polymer-based materials is that their chemical structure can be modified to enhance their reactivity, biocompatibility, resistance to degradation, and flexibility.

Application of nanomaterials in microbial-cell biosensor constructions

2015 ◽  
Vol 69 (1) ◽  
Author(s):  
Jana Šefčovičová ◽  
Jan Tkac
Keyword(s):  
Carbon Nanotubes ◽  
Gold Nanoparticles ◽  
Rapid Detection ◽  
Food Industry ◽  
Low Cost ◽  
Microbial Cell ◽  
Direct Connection ◽  
Qualitative Detection ◽  
Analytical Tools ◽  
Cell Biosensor

AbstractMicrobial cell biosensors, where cells are in direct connection with a transducer enabling quantitative and qualitative detection of an analyte, are very promising analytical tools applied mainly for assays in the environmental field, food industry or biomedicine. Microbial cell biosensors are an excellent alternative to conventional analytical methods due to their specificity, rapid detection and low cost of analysis. Nowadays, nanomaterials are often used in the construction of biosensors to improve their sensitivity and stability. In this review, the combination of microbial and other individual cells with different nanomaterials (carbon nanotubes, graphene, gold nanoparticles, etc.) for the construction of biosensors is described and their applications are provided as well.

Forming of Zeolite/Carbon Composite Substrate Coated with Titania for Photocatalyst Decomposition of Organic Compound

2015 ◽  
Vol 659 ◽  
pp. 304-309
Author(s):  
Khemmakorn Gomonsirisuk ◽  
Thanakorn Wasanapiarnpong
Keyword(s):  
Activated Carbon ◽  
Composite Materials ◽  
Low Cost ◽  
Carbon Composite ◽  
Phenolic Resins ◽  
Soaking Time ◽  
Naa Zeolite ◽  
Composite Substrate ◽  
Zeolite Composite ◽  
High Absorption

Organic contaminated wastes water from petrochemical industries can be removed by adsorbent and photocatalyst. In this work, the degradation rate of phenol have been studied at different ratios of activated carbon/NaA zeolite composite materials coated with TiO2 photocatalyst which are easily to be fabricated into tubular shape by extrusion method. In addition, the foam-inserted composite can be floated on the surface of waste water for the higher phocatalyst activity. While the composite is the low cost adsorbent with high absorption and high ion exchange properties. In order to optimize the efficiency of material, the various ratios of activated carbon/NaA zeolite (3:1, 1:1 and 1:3) and amount of coated TiO2 on the specimen’s surface was studied by UV/Vis spectrophotometer which related to phenol concentration. Moreover the various amount of phenolic resins (10, 20, 30, 40 and 50 wt%) at different reduction firing temperatures (600 and 650 °C) with soaking time of 1, 2 and 3 hours affected to the compressive strength of samples. For the characterization, XRD is used to characterize the phase and SEM is used to provide the morphology of the prepared composite materials.

scholarly journals Green Synthesis of Silver and Gold Nanoparticles via Sargassum serratifolium Extract for Catalytic Reduction of Organic Dyes

Catalysts ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 347
Author(s):  
Beomjin Kim ◽  
Woo Chang Song ◽  
Sun Young Park ◽  
Geuntae Park
Keyword(s):  
Gold Nanoparticles ◽  
Green Synthesis ◽  
Catalytic Reduction ◽  
Organic Dyes ◽  
Low Cost ◽  
Inorganic Nanoparticles ◽  
X Ray ◽  
Selected Area Electron Diffraction ◽  
Transmission Electron ◽  
Sargassum Serratifolium

The green synthesis of inorganic nanoparticles (NPs) using bio-materials has attained enormous attention in recent years due to its simple, eco-friendly, low-cost and non-toxic nature. In this work, silver nanoparticles (AgNPs) and gold nanoparticles (AuNPs) were synthesized by the marine algae extract, Sargassum serratifolium (SS). The characteristic studies of bio-synthesized SS-AgNPs and SS-AuNPs were carried out by using ultraviolet–visible (UV–Vis) absorption spectroscopy, dynamic light scattering (DLS), high-resolution transmission electron microscope (HR-TEM), selected area electron diffraction (SAED), energy-dispersive X-ray spectroscopy (EDX), X-ray powder diffraction (XRD) and Fourier transform infrared spectroscopy (FT-IR). Phytochemicals in the algae extract, such as meroterpenoids, acted as a capping agent for the NPs’ growth. The synthesized Ag and Au NPs were found to have important catalytic activity for the degradation of organic dyes, including methylene blue, rhodamine B and methyl orange. The reduction of dyes by SS-AgNPs and -AuNPs followed the pseudo-first order kinetics.

Performance of Low-Cost 3D Printer in Medical Application

2021 ◽  
Author(s):  
Nor Aiman Sukindar ◽  
Azib Azhari Awang Dahan ◽  
Sharifah Imihezri Syed Shaharuddin ◽  
Nor Farah Huda Abd Halim
Keyword(s):  
Low Cost ◽  
Medical Application ◽  
Fused Deposition Modelling ◽  
3D Printer ◽  
Layer By Layer ◽  
Total Deformation ◽  
Element Analysis ◽  
Porosity Level ◽  
Fused Deposition ◽  
Printing Parameters

Abstract Fused Deposition Modelling (FDM) is an additive manufacturing (AM) process that produces a physical object directly from a CAD design using layer-by-layer deposition of the filament material that is extruded via a nozzle. In industry, FDM has become one of the most used AM processes for the production of low batch quantity and functional prototypes, due to its safety, efficiency, reliability, low cost, and ability to process manufacturing-grade engineering thermoplastic. Recently, the market is flooded with the availability of low-cost printers produced by numerous companies. This research aims to investigate the effect of different porosity levels on a scaffold structure produced using a low-cost 3D printer. Comparisons of these porous structures were made in terms of Von-Mises strain, total deformation, as well as compressive stress. Various porosity levels were created by varying printing parameters, including layer height, infill density, and shell thickness by slicing the initial solid CAD file using Repetier Host 3D printing software. Finite Element Analysis (FEA) simulation was then performed on the created scaffold structures by using Ansys Workbench 19.2. The simulation result indicates that the greater porosity level will result in higher total deformation of the structure. Meanwhile, the compression test shows that the minimum strength value obtained was favourable at 22 MPa and had exceeded that of the trabecular femur (15 MPa). However, its porosity level (maximum at 52%) was still below that of the minimum threshold of porosity level of 70 percent. However, the printing parameters currently used can be adjusted in the future. Therefore, it was deduced that the low-cost 3D printer offers promising potential to fabricate different porosity structures with multiple outcomes.

Design and Analysis of Hybrid Fused Filament Fabrication Apparatus for Fabrication of Composites

2021 ◽  
Vol 14 ◽  
Author(s):  
Aniket Yadav ◽  
Piyush Chohan ◽  
Ranvijay Kumar ◽  
Jasgurpreet Singh Chohan ◽  
Raman Kumar
Keyword(s):  
Additive Manufacturing ◽  
Composite Materials ◽  
Design Process ◽  
Low Cost ◽  
Matrix Material ◽  
Fabrication Process ◽  
Layer By Layer ◽  
Fused Filament Fabrication ◽  
Composite Manufacturing ◽  
Tool Paths

Background: Additive manufacturing is the most famous technology which requires materials or composites to be fabricated with layer by layer deposition strategy. Due to its lower cost, higher accuracy and less material wastage; this technology is used in almost every sector. But in many applications there is a need to alter the properties of a product in a certain direction with the help of some reinforcements. With the use of reinforcements, composite layers can be fabricated using additive manufacturing technique which will enhance the directional properties. A novel apparatus is designed to spray the reinforcement material into the printed structures in a very neat and precise manner. This spray nozzle is fully automated, which works according to tool-paths generated by slicing software. The alternate deposition of layers of reinforcement and build materials helped to fabricate customized composite products. Objective: The objective of present study is to design and analyze the working principle of novel technique which has been developed to fabricate composite materials using additive manufacturing. The apparatus is numerically controlled by computer according to CAD data which facilitates the deposition of alternate layers of reinforcement and matrix material. The major challenges during the design process and function of each component has been explored. Methods: The design process is initiated after comprehensive literature review performed to study previous composite manufacturing processes. The recent patents published by different patent offices of the world are studied in detail and analysis has been used to design a low cost composite fabrication apparatus. A liquid dispensing device comprises a storage tank attached with a pump and microprocessor. The microprocessor receives the signal from the computer as per tool paths generated by slicing software which decides the spray of reinforcements on polymer layers. The spraying apparatus moves in coordination with the primary nozzle of the Fused Filament Fabrication process. Results: The hybridization of Fused Filament Fabrication [process with metal spray process has been successfully performed. The apparatus facilitates the fabrication of low cost composite materials along with flexibility of complete customization of composite manufacturing process. The anisotropic behaviour of products can be easily controlled and managed during fabrication which can be used for different applications.

Sign in / Sign up

Export Citation Format

Share Document