Recent Advances in Low K Polymeric Materials

1997 ◽  
Vol 476 ◽  
Author(s):  
K. R. Carter
Keyword(s):  
Integrated Circuit ◽  
Polymeric Materials ◽  
Turn Of The Century ◽  
Dielectric Constants ◽  
Limiting Factor ◽  
Microelectronic Device ◽  
Low Dielectric ◽  
Fluorinated Polyimides ◽  
Low Dielectric Constant Materials ◽  
Low K

AbstractAs microelectronic device dimensions decrease and functionality density increases, a change in interconnect materials, both conductors and insulators must change from currently used materials. To this end, we are actively in search of low dielectric constant materials that can be integrated into integrated circuit production. The greatest limiting factor in materials qualification are the stringent IC processing conditions (thermal stability, resistance to chemical/mechanical treatments). Current specifications for back-end-of-the-line (BEOL) thin film insulators call for materials with dielectric constants of 3.0–3.5 and turn of the century CMOS devices may require materials with dielectric constants approaching 2.0. While there are a number of possible candidates for current uses, the list of usable materials with dielectric constants <3.0 is very limited. Future low K candidates being examined include fluorinated polyimides and porous materials.

Organic and Inorganic Spin-On Polymers for Low-Dielectric-Constant Applications

MRS Bulletin ◽  
1997 ◽  
Vol 22 (10) ◽  
pp. 33-38 ◽  
Author(s):  
Nigel P. Hacker
Keyword(s):  
Dielectric Constant ◽  
Integrated Circuit ◽  
Chemical Properties ◽  
Chemical Vapor ◽  
Polymeric Materials ◽  
Dielectric Constants ◽  
Low Dielectric Constant ◽  
Low Dielectric ◽  
Chip Size ◽  
Low Dielectric Constant Materials

Low-dielectric-constant materials (k < 3.0) have the advantage of facilitating manufacture of higher performance integrated-circuit (IC) devices with minimal increases in chip size. The reduced capacitance given by these materials permits shrinkage of spacing between metal lines to below 0.25 μm and the ability to decrease the number of levels of metal in a device. The technologies being considered for low-k applications are chemical vapor deposition (CVD) or spin-on of polymeric materials. For both types of processes, there are methods and materials capable of giving k < 3.0 dielectric stacks. This article will focus on the spin-on approach and discuss the properties of both organic and inorganic spin-on polymers.While CVD SiO2 has been the mainstay of the industry, spin-on materials are appropriate for many dielectric applications. Polyimides have applications as electrical insulators, and traditional spin-on silicates or siloxanes (k > 3.0) have served as planarizing dielectrics during the last 15 years. The newer spin-on polymers have greatly enhanced mechanical, thermal, and chemical properties, exhibiting lower dielectric constants than the traditional materials.

Properties of New Low Dielectric Constant Spin-on Silicon Oxide based Polymers

1997 ◽  
Vol 476 ◽  
Author(s):  
Nigel P. Hacker ◽  
Gary Davis ◽  
Lisa Figge ◽  
Todd Krajewski ◽  
Scott Lefferts ◽  
...  
Keyword(s):  
Dielectric Constant ◽  
Silicon Oxide ◽  
Polymeric Materials ◽  
Low Dielectric Constant ◽  
Low Dielectric ◽  
Chip Size ◽  
Low Dielectric Constant Materials ◽  
Low K

Low dielectric constant materials (k < 3.0) have the advantage that higher performance IC devices may be manufactured with minimal increases in chip size. The reduced capacitance given by these materials permits shrinking spacing between metal lines to below 0.25 μm and the ability to decrease the number of levels of metal in a device. The technologies being considered for low k applications are CVD or spin-on of inorganic or organic polymeric materials. Traditional spin-on silicates or siloxanes have been used as planarizing dielectrics during the last 15 years and usually have k > 3.0.

Determination of the Modulus and Hardness of Spin-on Zeolite Low-K Thin Films

2005 ◽  
Vol 880 ◽  
Author(s):  
Mark Johnson ◽  
Zijian Li ◽  
Yushan Yan ◽  
Junlan Wang
Keyword(s):  
Thin Films ◽  
Integrated Circuit ◽  
Material Selection ◽  
Dielectric Materials ◽  
Dielectric Constants ◽  
Depth Sensing ◽  
New Class ◽  
Low Dielectric ◽  
Pure Silica ◽  
Low K

AbstractWith the semiconductor technologies continuously pushing the miniaturization limits, there is a growing interest in developing novel low dielectric constant (low-k) materials to replace traditional dense SiO2 based insulators. In order to survive the multi-step integration process and provide reliable material and structure for the desired integrated circuit (IC) functions, the new low-k materials have to be mechanically strong and stable. Thus the material selection and mechanical characterization are vital in the successful development of next generation low-k dielectrics. A new class of low-k dielectric materials, nanoporous pure-silica zeolite, is prepared in thin films using IC compatible spin coating process and characterized using depth sensing nanoindentation technique. The elastic modulus measurements of the zeolite thin films are found to be significantly higher than that of other porous silicates with similar porosity and dielectric constants. Correlations of the mechanical, microstructural and electrical properties are discussed in detail.

Thermal conductivity study of porous low K dielectric materials

1999 ◽  
Vol 565 ◽  
Author(s):  
Chuan Hu ◽  
Michael Morgen ◽  
Paul S. Ho ◽  
Anurag Jain ◽  
William. N. Gill ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Dielectric Materials ◽  
Porous Films ◽  
Low Dielectric ◽  
Omega Method ◽  
3 Omega ◽  
Low Dielectric Constant Materials ◽  
Low K ◽  
Method Analysis

AbstractA quantitative characterization of the thermal properties is required to assess the thermal performance of low dielectric constant materials. Recently we have developed a technique based on the 3-omega method for measuring the thermal conductivity of porous dielectric thin films. In this paper we present the results on the measurements of thermal conductivity of thin porous films using this method. A finite element method analysis is used to evaluate the approximations used in the measurement. Two porosity-weighted thermal resistor models are proposed to interpret the results. By studying the dependence of the thermal conductivity on porosity, we are able to discuss the scaling rule of thermal conductivity. Additionally, a steady state layered heater model is used for evaluating the significance of introducing porous ILDs into an interconnect structure.

New Carbon-bridged Hybrid Polymers for Low-k Materials

2005 ◽  
Vol 863 ◽  
Author(s):  
Bum-Gyu Choi ◽  
Byung Ro Kim ◽  
Myung-Sun Moon ◽  
Jung-Won Kang ◽  
Min-Jin Ko
Keyword(s):  
Mechanical Properties ◽  
Hybrid Materials ◽  
Chemical Mechanical Planarization ◽  
Sol Gel ◽  
Dielectric Constants ◽  
Metal Line ◽  
Inorganic Hybrid ◽  
Low Dielectric ◽  
Continuous Stiffness Measurement ◽  
Low K

AbstractReducing interline capacitance and line resistance is required to minimize RC delays, reduce power consumption and crosstalk below 100nm node technology. For this purpose, various inorganic- and organic polymers have been tested to reduce dielectric constants in parallel with the use of copper as metal line. Lowering the dielectric constants, in particular, causes the detrimental effect on mechanical properties, and then leads to film damage and/or delamination during chemical-mechanical planarization CMP) or repeated thermal cure cycles. To overcome this issue, new carbon-bridged hybrid materials synthesized by organometallic silane precursors and sol-gel reaction are proposed.In this work, we have developed new organic-inorganic hybrid low-k dielectrics with linear or cyclic carbon bridged structures. The differently bridged carbon structures were formed by a controlled reaction. 1H NMR, 29Si NMR analysis and GC/MSD analysis were conducted for the structural characterization of new hybrid low-k dielectric. The mechanical and dielectric properties of these hybrid materials were characterized by using nanoindentation with continuous stiffness measurement and Al dot MIS techniques. The results indicated that these organic-inorganic hybrid materials were very promising polymers for low-k dielectrics that had low dielectric constants with high thermal and mechanical properties. It has been also demonstrated that electrical and mechanical properties of the hybrid films could be tailored by copolymerization with PMSSQ and through the introduction of porogen.

Electrical, Mechanical, and Structural Properties of Fluoro-Containing Poly(silsesquioxanes) Based Porous Low k Thin Films

2003 ◽  
Vol 766 ◽  
Author(s):  
Jingyu Hyeon-Lee ◽  
Jihoon Rhee ◽  
Jungbae Kim ◽  
Jin-Heong Yim ◽  
Seok Chang
Keyword(s):  
Thin Films ◽  
Pore Size ◽  
Dielectric Constants ◽  
Commercial Application ◽  
Porous Films ◽  
Low Dielectric ◽  
Nanoporous Films ◽  
Positronium Annihilation ◽  
Positronium Annihilation Lifetime Spectroscopy ◽  
Low K

AbstractLow dielectric fluoro-containing poly(silsesquioxanes) (PSSQs) have been synthesized using trifluoropropyl trimethoxysilane (TFPTMS), methyl trimethoxysilane (MTMS), and 2, 4, 6, 8-tetramethyl-2, 4, 6, 8-tetra(trimethoxysilylethyl) cyclotetrasiloxane. The properties of fluorocontaining PSSQs based thin films were studied by electrical, mechanical, and structural characterization. Film was spun on a silicon substrate, baked at 150°C and 250°C for 1 minute, respectively, and cured in the furnace at 420°C for 1 hour under vacuum condition. Thermally decomposable trifluoropropyl groups of the fluoro-containing PSSQ were served as a pore generator and partially contributed to lower a dielectric constant. â-cyclodextrin (CD) was also employed as a pore generator. The concentration of the pore generator in the film was varied from 0 to 30 %. The dielectric constants of the porous PSSQ films were found to be in the range of 2.7 – 1.9 (at 100 kHz). Hardness and Young's modulus of the films were measured by nano-indentation. The elastic modulus and hardness of the porous films were well correlated with the concentration of the pore generators. Positronium Annihilation Lifetime Spectroscopy (PALS) was employed to characterize a pore size of the porous fluoro-containing PSSQ film. The pore size of the film was less than 2.2 nm. The nanoporous films showed quite promising properties for commercial application.

Ultra-low dielectric constant materials with hydrophobic property derived from polyhedral oligomeric silsequioxane (POSS) and perfluoro-aromatics

RSC Advances ◽  
2016 ◽  
Vol 6 (90) ◽  
pp. 87433-87439 ◽  
Author(s):  
Jinmeng Hao ◽  
Yanfeng Wei ◽  
Jianxin Mu
Keyword(s):  
Dielectric Constant ◽  
Dielectric Constants ◽  
Low Dielectric Constant ◽  
Hydrophobic Property ◽  
Hydrophobic Properties ◽  
Low Dielectric ◽  
Arylene Ether ◽  
Low Dielectric Constant Materials ◽  
Soluble Poly

Soluble poly(arylene ether)s with perfluoro-aromatics and POSS in the main chains exhibited ultra low dielectric constants and hydrophobic properties.

Process Integration issues for Interlevel Dielectric Materials for Sub-quarter Micron Silicon Integrated Circuits

1998 ◽  
Vol 511 ◽  
Author(s):  
Vijay Parihar ◽  
R. Singh
Keyword(s):  
Integrated Circuits ◽  
Integrated Circuit ◽  
Process Integration ◽  
Dielectric Materials ◽  
New Approach ◽  
Interlayer Dielectric ◽  
Low Dielectric ◽  
Silicon Integrated Circuits ◽  
Processing Techniques ◽  
Low K

ABSTRACTThe continued miniaturization towards sub-quarter micron feature size mandates the search for low dielectric constant interlayer dielectric materials. A large number of materials and processing techniques has been suggested, but so far none of the proposed dielectric materials as well as processing techniques have been integrated into standard integrated circuit processing. In this paper, a new approach has been formulated for integration of low-k dielectric materials for future integrated circuits.

Preparation and Properties of Polyisoimides as a Highly Dimensionally Stable Polyimide Precursor with Low Dielectric Constant

1997 ◽  
Vol 9 (3) ◽  
pp. 333-344 ◽  
Author(s):  
Hiroshi Seino ◽  
Osamu Haba ◽  
Amane Mochizuki ◽  
Masahiro Yoshioka ◽  
Mitsuru Ueda
Keyword(s):  
Dielectric Constant ◽  
Dielectric Constants ◽  
Isomerization Reaction ◽  
Low Dielectric Constant ◽  
Low Dielectric ◽  
Fluorinated Polyimides ◽  
Wide Range ◽  
Biphenyltetracarboxylic Dianhydride ◽  
Polyimide Precursor ◽  
Dipolar Aprotic Solvents

Fluorinated polyimides (PIs) with low dielectric constant and high dimensional stability have been developed using polyisoimides (PIIs) as a polyimide precursor. The PIIs were prepared by the ring-opening polyaddition of the dianhydrides pyromellitic dianhydride, biphenyltetracarboxylic dianhydride and 4, 4′-hexafluoropropylidenedi(phthalic anhydride) with the diamines 2, 2′-dimethylbenzidine and 2, 2′-bis(trifluoromethyl)benzidine, followed by treatment with trifluoroacetic anhydride/triethylamine or dicyclohexylcarbodiimide in N;N-dimethylacetamide. The PIIs were soluble in a wide range of solvents including dipolar aprotic solvents, cyclohexanone and tetrahydrofuran at room temperature, and easy to convert to corresponding PIs by high thermal treatment. The resulting PIs showed low dielectric constants of less than 3 at 1 MHz as well as low CTEs. Furthermore, during the isomerization reaction, migration of copper in the PI film was hardly observed.

Sign in / Sign up

Export Citation Format

Share Document