Mechanical Properties of L12 Type Zn3Ti-Base Alloy

1998 ◽  
Vol 552 ◽  
Author(s):  
Hideki Hosoda ◽  
Shuji Hanada
Keyword(s):  
Mechanical Properties ◽  
Thermal Analysis ◽  
Ball Mill ◽  
Room Temperature ◽  
Base Alloy ◽  
Positive Temperature ◽  
Compression Tests ◽  
X Ray Diffraction ◽  
X Ray ◽  
Hardness Tests

ABSTRACTAn alloy composed of L12-type Zn3Ti was investigated in terms of phase stability and mechanical properties. Zn and Ti powders were mixed at a composition of Zn-25mol%Ti using a ball mill in Ar, and an ingot was made by melting the powders. Optical microscopy, X-ray diffraction analysis and thermogravimetry - differential thermal analysis were carried out. Mechanical properties were investigated by Vickers hardness tests at room temperature (RT) and compression tests from RT to 703K in Ar. It is found that (1) the alloy is mainly composed of L12 Zn3Ti, (2) the alloy has weak positive temperature dependence of strength, and (3) normalized strength by melting point is comparable to that of L12 Al3Ti-Cr alloys. L12 Zn3Ti has HV178 and is brittle at RT. Reaction temperatures of Zn-rich portion of the Zn-Ti phase diagram were also reinvestigated and a peritectic-reaction temperature between Zn3Ti and liquid + Zn2Ti is determined to be at 880K.

Microstructural and Mechanical Properties of Ti3Al-Based Intermetallics Produced by Powder Metallurgy

2005 ◽  
Vol 494 ◽  
pp. 211-216 ◽  
Author(s):  
B. Dimčić ◽  
M. Vilotijević ◽  
D. Božić ◽  
D. Rajnović ◽  
M.T. Jovanović
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Powder Metallurgy ◽  
Room Temperature ◽  
Solution Treatment ◽  
Microstructural Characterization ◽  
Compression Tests ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

The structural and compression mechanical properties of Ti3Al-based intermetallics produced by powder metallurgy techniques have been studied. The as-milled powders were compacted by hot pressing to non-porous homogenous compacts. Prior to compression tests, all compacts were homogenized by a solution treatment at 1050°C (a+β region) for 1h, followed by water quenching. The compression tests were performed from room temperature to 500°C in vacuum at a strain rate of 1 3 10 4 . 2 − − × s . Detailed microstructural characterization was evaluated by scanning electron microscopy (SEM), followed by energy dispersive spectroscopy (EDS) and X-ray diffraction analysis.

scholarly journals The Potential for Natural Stones from Northeastern Brazil to Be Used in Civil Construction

Minerals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 440
Author(s):  
Fabiana Pereira da Costa ◽  
Jucielle Veras Fernandes ◽  
Luiz Ronaldo Lisboa de Melo ◽  
Alisson Mendes Rodrigues ◽  
Romualdo Rodrigues Menezes ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Thermal Analysis ◽  
Differential Thermal Analysis ◽  
Chemical Resistance ◽  
Mechanical Analysis ◽  
Northeastern Brazil ◽  
X Ray Diffraction ◽  
X Ray ◽  
Chemical Agents ◽  
Natural Stones

Natural stones (limestones, granites, and marble) from mines located in northeastern Brazil were investigated to discover their potential for use in civil construction. The natural stones were characterized by chemical analysis, X-ray diffraction, differential thermal analysis, and optical microscopy. The physical-mechanical properties (apparent density, porosity, water absorption, compressive and flexural strength, impact, and abrasion) and chemical resistance properties were also evaluated. The results of the physical-mechanical analysis indicated that the natural stones investigated have the potential to be used in different environments (interior, exterior), taking into account factors such as people’s circulation and exposure to chemical agents.

Physical and Mechanical Properties of Cement Paste Were Used Partially with Fly Ash and Kaolin Waste

2017 ◽  
Vol 866 ◽  
pp. 199-203
Author(s):  
Chidchanok Chainej ◽  
Suparut Narksitipan ◽  
Nittaya Jaitanong
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Room Temperature ◽  
Physical And Mechanical Properties ◽  
Partial Replacement ◽  
X Ray Diffraction ◽  
X Ray ◽  
Lime Water ◽  
Diffraction Patterns ◽  
Iron Mold

The aims of this research were study the microstructures and mechanical properties for partial replacement of cement with Fly ash (FA) and kaolin waste (KW). Ordinary Portland cement were partially replaced with FA and KW in the range of 25-35% and 10-25% by weight of cement powder. The kaolin waste was ground for 180 minutes before using. The specimen was packing into an iron mold which sample size of 5×5×5 cm3. Then, the specimens were kept at room temperature for 24 hours and were moist cured in the incubation lime water bath at age of 3 days. After that the specimens were dry cured with plastic wrap at age of 3, 7, 14 and 28 days. After that the compounds were examined by x-ray diffraction patterns (XRD) and the microstructures were examined by scanning electron microscopy (SEM). The compressive strength was then investigated.

STRUCTURE AND MAGNETIC PROPERTIES OF MECHANICAL ALLOYED Mn-15at.%Al

2013 ◽  
Vol 12 (01) ◽  
pp. 1350006
Author(s):  
AHMED E. HANNORA ◽  
FARIED F. HANNA ◽  
LOTFY K. MAREI
Keyword(s):  
Thermal Analysis ◽  
Room Temperature ◽  
Average Crystallite Size ◽  
Al Alloy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Milled Sample ◽  
Powder Samples ◽  
Xrd Patterns ◽  
Method Analysis

Mechanical alloying (MA) method has been used to produce nanocrystallite Mn -15at.% Al alloy. X-ray diffraction (XRD) patterns for the as-milled elemental α- Mn and aluminum powder samples show a mixture of α + β- MnAl phases after 20 h of milling and changes to a dominant β- MnAl phase structure after 50 h. An average crystallite size of 40 nm was determined from Hall–Williamson method analysis after 5 h of milling. Moreover, the thermal analysis results using differential thermal analysis (DTA), suggested a possible phase transformation after 20 h of milling. Isothermal treatments are carried in the temperature range of 450°C to 1000°C. Room-temperature vibrating sample magnetometer (VSM) measurements of the hysteretic response revealed that the saturation magnetization Bs and coercivity Hc for 10 h ball milled sample are ~ 2.1 emu/g and ~ 92 Oe, respectively.

Effect of Hot Forging and Different Cooling Rates on the Microstructure, Mechanical Properties of Carbon Steel Containing 0.8 and 1.2Al

2014 ◽  
Vol 622-623 ◽  
pp. 174-178
Author(s):  
Ahmed Ismail Zaky Farahat ◽  
Mohamed Kamal Elfawkhry
Keyword(s):  
Mechanical Properties ◽  
Carbon Steel ◽  
Mechanical Testing ◽  
Room Temperature ◽  
Induction Furnace ◽  
Hot Forging ◽  
X Ray Diffraction ◽  
Cooling Rates ◽  
X Ray ◽  
Sem Microstructure

Two alloys of steel containing nominally 0.45C-1.0Si-2.0Mn-0.8Al and 1.2Al were cast in open air induction furnace. Dilatation testing was carried out to recognize the effect on Aluminum on the different critically transformation temperatures. The alloys were hot forged at 1200°C and then subjected to different cooling rates. Mechanical testing was carried out at room temperature. Optical and SEM microstructure were observed. X-ray diffraction was conducted to observe the microstructure constituents.

Effect of Nitrogen Addition on Mechanical Property of Ti-Cr-Sn Alloy

2010 ◽  
Vol 654-656 ◽  
pp. 2126-2129 ◽  
Author(s):  
Yuichi Nakahira ◽  
Tomonari Inamura ◽  
Hiroyasu Kanetaka ◽  
Shuichi Miyazaki ◽  
Hideki Hosoda
Keyword(s):  
Mechanical Properties ◽  
Room Temperature ◽  
Tensile Tests ◽  
Nitrogen Addition ◽  
N Addition ◽  
X Ray Diffraction ◽  
Solution Hardening ◽  
X Ray ◽  
Bcc Phase ◽  
Cold Workability

Effect of nitrogen (N) addition on mechanical properties of Ti-Cr-Sn alloy was investigated in this study. Ti-7mol%Cr-3mol%Sn was selected and less than 0.5wt% of N were systematically added. The alloys were characterized by optical microscopy, X-ray diffraction analysis and tensile tests at room temperature. The apparent phase was β (bcc) phase, whereas the presence of precipitates was confirmed in 0.5wt%N-added alloy only which did not exhibit sufficient cold workability. The grain size was not largely affected by N addition being less than 0.5wt%. Tensile tests revealed that less than 0.5wt%N addition improves the strength which is due to the solution hardening by interstitial N atoms.

Mechanical Behavior of the Cr3C2 Compound at High Pressure and High Temperature

2015 ◽  
Vol 1120-1121 ◽  
pp. 1187-1193 ◽  
Author(s):  
Bin Li Jiang ◽  
Zi Li Kou ◽  
De Jiang Ma ◽  
Yong Kun Wang ◽  
Chun Xia Li ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
High Pressure ◽  
Relative Density ◽  
X Ray Diffraction ◽  
Density Measurements ◽  
X Ray ◽  
Hardness Tests ◽  
Novel Method ◽  
Heat Preservation

In the present study, we present a novel method to sinter Cr3C2 powders under high pressure without any addittives. The sintering Cr3C2 samples were charaterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), relative density measurements, Vicker’s hardness tests and Fracture toughness tests. The reasults show that Cr3C2 powders could be sintered to be bulk under the conditions of 3-5 GPa, 800-1200 °C and the heat preservation for 15 min. Moreover, the sintering body of Cr3C2 compound with the relative density of 99.84% by simultaneously tuning the pressure-temperature conditions exhibited excellent mechanical properties: a Vickers hardness of 20.3 GPa and a fracture toughness of ~8.9 MPam1/2. These properties were much higher than that by using the previous methods. The temperature condition obtained good mechanical properties in the experiment was about 1/3 lower than that using any other methods owing to the high pressure.

Effects of Extrusion on the Mechanical Properties and Damping Capacity of Mg-1.8Cu-0.5Mn Alloy

2007 ◽  
Vol 546-549 ◽  
pp. 257-260 ◽  
Author(s):  
Zhen Yan Zhang ◽  
Li Ming Peng ◽  
Xiao Qin Zeng ◽  
Lin Du ◽  
Lan Ma ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Properties ◽  
Room Temperature ◽  
Tensile Tests ◽  
Optical Microscope ◽  
Damping Capacity ◽  
X Ray Diffraction ◽  
Dynamic Mechanical Analyzer ◽  
X Ray ◽  
Solute Atoms

Effects of extrusion on mechanical properties and damping capacity of Mg-1.8wt.%Cu -0.5wt.%Mn (MCM1805) alloy have been investigated. Tensile tests and dynamic mechanical analyzer were respectively used to measure tensile properties and damping capacity at room temperature of as-cast and as-extruded MCM1805 alloy. The microstructure was studied using optical microscope, X-ray diffraction and scanning electron microscope with an energy dispersive X-ray spectrometer. Granato-Lücke model was used to explain the influences of extrusion on damping capacity of MCM1805 alloy. The results showed that extrusion dramatically decreases the grain size but has little influence on phase composition and solute atoms concentration of MCM1805 alloy, and the grain refinement was the dominant reason for the obvious increase of tensile properties and decrease of internal friction of MCM1805 alloy.

Effect of Deposition Temperature on the Structure and Mechanical Properties of Ti-6Al-4V Film

2013 ◽  
Vol 749 ◽  
pp. 643-647 ◽  
Author(s):  
Lei Li ◽  
Ya Feng Lu ◽  
Wen Xue Li ◽  
Li Ying Zeng ◽  
Yi Yang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Room Temperature ◽  
Elastic Moduli ◽  
Preferred Orientation ◽  
Nanoindentation Test ◽  
X Ray Diffraction ◽  
X Ray ◽  
Phase Direction ◽  
Higher Temperature ◽  
Substrate Temperatures

Ti-6Al-4V films were deposited by direct-current magnetron sputtering at different substrate temperatures. The structure and the surface morphology of the films were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The hardness and elastic moduli of Ti-6Al-4V films were measured by nanoindentation test. The results showed that the phase direction of the films deposited at room temperature was (102) orientation, and turned to almost complete (002) preferred orientation at 300°C. For a higher temperature of 500°C, the preferred orientation of the film disappeared and presented a random grain orientation. The hardness and elastic moduli of Ti-6Al-4V films obviously showed the dependence on the temperature. The relationships among temperature, microstructure and mechanical properties of Ti-6Al-4V films were discussed in this paper.

Effect of Iron Substitution on the High-temperature Properties of Sm(Co,Cu,Ti)z Permanent Magnets

2001 ◽  
Vol 674 ◽  
Author(s):  
Jian Zhou ◽  
Ralph Skomski ◽  
David J. Sellmyer ◽  
Wei Tang ◽  
George C. Hadjipanayis
Keyword(s):  
High Temperature ◽  
Room Temperature ◽  
Permanent Magnets ◽  
Site Occupancy ◽  
Positive Temperature Coefficient ◽  
Positive Temperature ◽  
X Ray Diffraction ◽  
Two Phase ◽  
X Ray ◽  
Iron Substitution

ABSTRACTRecently, Ti-substituted Sm-Co permanent magnets have attracted renewed attention due to their interesting high-temperature coercivity. Our presentation deals with the effect of iron substitutions on the magnetic properties of the materials. X-ray diffraction shows that the investigated Sm(Co,Fe,Cu,Ti)z materials (z = 7.0 - 7.6) are two-phase magnets, consisting of 1:5 and 2:17 regions. The iron content affects both the coercivity and the magnetization. Depending on composition and heat treatment, some samples show a positive temperature coefficient of the coercivity in the temperature range from 22 °C to 550 °C. Moderate amounts of iron enhance the room-temperature coercivity. For example, the room-temperature coercivity of Sm(Co6.0Fe0.4Cu0.6Ti0.3) is 9.6 kOe, as compared to 7.6 kOe for Sm(Co6.4Cu0.6Ti0.3). At high temperatures, the addition of Fe has a deteriorating effect on the coercivity, which is as high as 10.0 kOe at 500 °C for Sm(Co6.4Cu0.6Ti0.3). The room-temperature magnetization increases on iron substitution, from 73 emu/g for Sm(Co6.4Cu0.6Ti0.3) to 78 emu/g for Sm(Co6.0Fe0.4Cu0.6Ti0.3). The observed temperature dependence is ascribed to the preferential dumbbell-site occupancy of the Fe atoms.

Sign in / Sign up

Export Citation Format

Share Document