Ion Beam Deposited Gmr Materials

2001 ◽  
Vol 690 ◽  
Author(s):  
J. M. Lannon ◽  
C.C. Pace ◽  
D. Temple ◽  
G.E McGuire ◽  
A.F. Hebard ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Beam Energy ◽  
Giant Magnetoresistance ◽  
Ion Beam ◽  
Energy Distributions ◽  
Force Microscopy ◽  
Atomic Force ◽  
Transmission Electron ◽  
The Monte Carlo Method ◽  
Secondary Ion

ABSTRACTIon beam sputter deposition (IBSD) techniques for deposition of giant magnetoresistance (GMR) films have been studied using an automated IBSD system designed and built in-house. We have studied the properties of Fe/Cr multilayers deposited using either Ar or Xe ions with the primary ion beam energy varying from 500 eV to 1100 eV. The films were characterized using transmission electron microscopy (TEM), atomic force microscopy (AFM), Auger electron spectroscopy (AES), X-ray photoelectron spectroscopy (XPS), secondary ion mass spectroscopy (SIMS), magnetization measurements, and magnetoresistance measurements. The maximum value of GMR obtained was 49% (measured at 10K). For the Cr spacer thickness layer chosen, this GMR ratio is larger than the values reported for polycrystalline Fe/Cr multilayers deposited by magnetron sputtering. In general, we have found that GMR ratios for the Fe/Cr multilayers increase with decreasing primary ion beam energy, and are greater for films deposited using Xe ions than for films deposited using Ar ions. We explain the observed effects on the basis of energy distributions of sputtered atoms and backscattered working gas atoms (neutrals). The energy distributions were calculated using TRIM (Transport of Ions in Matter) software based on the Monte Carlo method.

Comparative Analysis of the Nucleation and Growth of Copper on Different Low-k Polymers

2001 ◽  
Vol 714 ◽  
Author(s):  
V. Zaporojtchenko ◽  
J. Erichsen ◽  
T. Strunskus ◽  
K. Behnke ◽  
F. Faupel ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Ion Beam ◽  
Depth Profiling ◽  
Nucleation And Growth ◽  
Force Microscopy ◽  
Teflon Af ◽  
Atomic Force ◽  
Transmission Electron ◽  
Beam Depth ◽  
Low K

ABSTRACTIn this work we present investigations of the nucleation and growth of evaporated copper on several low-k polymers. The evolving interfaces were characterized using transmission electron microscopy (TEM), x-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). The results were compared between the PMDA/ODA polyimide, Teflon AF 1601 and Silk®. A diffusion coefficient for copper atoms in Silk® determined by low energy ion-beam depth profiling in conjunction with XPS is reported.

scholarly journals Studying Corrosion Using Miniaturized Particle Attached Working Electrodes and the Nafion Membrane

Micromachines ◽  
2021 ◽  
Vol 12 (11) ◽  
pp. 1414
Author(s):  
Jiyoung Son ◽  
Edgar C. Buck ◽  
Shawn L. Riechers ◽  
Shalini Tripathi ◽  
Lyndi E. Strange ◽  
...  
Keyword(s):  
Electrochemical Performance ◽  
Photoelectron Spectroscopy ◽  
Focused Ion Beam ◽  
Secondary Ion Mass Spectrometry ◽  
Ion Beam ◽  
Nafion Membrane ◽  
New Approach ◽  
Force Microscopy ◽  
Atomic Force ◽  
Secondary Ion

We developed a new approach to attach particles onto a conductive layer as a working electrode (WE) in a microfluidic electrochemical cell with three electrodes. Nafion, an efficient proton transfer molecule, is used to form a thin protection layer to secure particle electrodes. Spin coating is used to develop a thin and even layer of Nafion membrane. The effects of Nafion (5 wt% 20 wt%) and spinning rates were evaluated using multiple sets of replicates. The electrochemical performance of various devices was demonstrated. Additionally, the electrochemical performance of the devices is used to select and optimize fabrication conditions. The results show that a higher spinning rate and a lower Nafion concentration (5 wt%) induce a better performance, using cerium oxide (CeO2) particles as a testing model. The WE surfaces were characterized using atomic force microscopy (AFM), scanning electron microscopy-focused ion beam (SEM-FIB), time-of-flight secondary ion mass spectrometry (ToF-SIMS), and X-ray photoelectron spectroscopy (XPS). The comparison between the pristine and corroded WE surfaces shows that Nafion is redistributed after potential is applied. Our results verify that Nafion membrane offers a reliable means to secure particles onto electrodes. Furthermore, the electrochemical performance is reliable and reproducible. Thus, this approach provides a new way to study more complex and challenging particles, such as uranium oxide, in the future.

Curcumin delivery by modified biosourced carbon-based nanoparticles

Nanomedicine ◽  
2022 ◽  
Author(s):  
Hossein Danafar ◽  
Marziyeh Salehiabar ◽  
Murat Barsbay ◽  
Hossein Rahimi ◽  
Mohammadreza Ghaffarlou ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Free System ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force ◽  
Transmission Electron ◽  
Good Biocompatibility ◽  
Drug Free ◽  
Mcf 7 ◽  
Carbon Based

Aim: To prepare a novel hybrid system for the controlled release and delivery of curcumin (CUR). Methods: A method for the ultrasound-assisted fabrication of protein-modified nanosized graphene oxide-like carbon-based nanoparticles (CBNPs) was developed. After being modified with bovine serum albumin (BSA), CUR was loaded onto the synthesized hybrid (labeled CBNPs@BSA–CUR). The structure and properties of the synthesized nanoparticles were elucidated using transmission electron microscopy (TEM), atomic force microscopy (AFM), ultraviolet-visible spectroscopy (UV-Vis), Fourier-transform infrared spectroscopy (FTIR) and x-ray photoelectron spectroscopy (XPS) methods. Results: CBNPs@BSA–CUR showed pH sensitivity and were calculated as controlled CUR release behavior. The drug-free system exhibited good biocompatibility and was nontoxic. However, CBNPs@BSA–CUR showed acceptable antiproliferative ability against MCF-7 breast cancer cells. Conclusion: CBNPs@BSA–CUR could be considered a highly promising nontoxic nanocarrier for the delivery of CUR with good biosafety.

Surface and Interface Characterization of Ion Beam Re-crystallized Si

2002 ◽  
Vol 750 ◽  
Author(s):  
P. K. Sahoo ◽  
B. Satpati ◽  
S. Dey ◽  
P. V. Satyam ◽  
T. Som ◽  
...  
Keyword(s):  
Ion Beam ◽  
Amorphous Layer ◽  
Amorphous Structure ◽  
Average Height ◽  
Force Microscopy ◽  
Surface And Interface ◽  
Atomic Force ◽  
Nano Crystalline ◽  
Transmission Electron

ABSTRACTIn the present work we have studied efficacy of ion beam induced epitaxial crystallization (IBIEC) to recover amorphous layers (300 – 350 nm) produced by MeV Kr ions in Si(100) and studied the associated changes occurring on surface and interface of the recrystallized region. IBIEC experiments were carried out at sample temperatures in the range of 200 − 400°C using 1 MeV N+ ion beam. Rutherford backscattering-Channeling technique showed planar and gradual recovery of the amorphous layer as a function of temperature. Transmission electron microscopy measurements show good crystalline structure of the recovered region at 400°C while at lower temperatures nano-crystalline Si formation embedded in the amorphous structure is evident. The surface topography studied by atomic force microscopy shows development of islands after IBIEC. The rms roughness is around 0.5 nm and average height of the islands is found to be 1.8 nm. The observed epitaxial growth and the surface topographical features have been correlated.

Ta2O5-Incorporated WO3 Nanocomposite Film for Improved Electrochromic Performance in an Acidic Condition

2006 ◽  
Vol 6 (11) ◽  
pp. 3572-3576 ◽  
Author(s):  
Hee-Sang Shim ◽  
Hyo-Jin Ahn ◽  
Youn-Su Kim ◽  
Yung-Eun Sung ◽  
Won Bae Kim
Keyword(s):  
Surface Roughness ◽  
Photoelectron Spectroscopy ◽  
Potential Cycling ◽  
Force Microscopy ◽  
Atomic Force ◽  
Transmission Electron ◽  
Continuous Potential ◽  
Chemical States ◽  
The Stability

We report electrochromic and electrochemical properties of a WO3-Ta2O5 nanocomposite electrode that was fabricated from co-sputtering. Transmission electron microscopy (TEM)images of the WO3-Ta2O5 nanocomposite electrode revealed that morphology of the WO3 film was changed by incorporation of Ta2O5 nanoparticles, and their chemical states were confirmed to be W6+ and Ta5+ oxides from X-ray photoelectron spectroscopy (XPS). The introduction of Ta2O5 to the WO3 film played a role in alleviating surface roughness increase during continuous potential cycling; whereas the surface roughness of the WO3 film was increased from ca. 3.0 nm to ca. 13.4 nm after 400 cycles, the roughness increase on the WO3-Ta2O5 was significantly reduced to 4.2 nm after 400 cycles, as investigated by atomic force microscopy (AFM). This improvement of the stability by adding Ta2O5 may be responsible for the enhanced electrochemical and optical properties over long-term cycling with the WO3-Ta2O5 nanocomposite electrode.

Thermal Stability and Analysis of Laser Deposited Platinum Films

2000 ◽  
Vol 624 ◽  
Author(s):  
G.J. Berry ◽  
J.A. Cairns ◽  
M.R. Davidson ◽  
Y.C. Fan ◽  
A.G. Fitzgerald ◽  
...  
Keyword(s):  
Thermal Stability ◽  
Photoelectron Spectroscopy ◽  
Elevated Temperatures ◽  
Surface Composition ◽  
Direct Write ◽  
Force Microscopy ◽  
Annealing Conditions ◽  
Atomic Force ◽  
Transmission Electron ◽  
Induced Decomposition

ABSTRACTAs the trend towards device miniaturisation continues, surface effects and the thermal stability of metal deposits becomes increasingly important. We present here a study of the morphology and composition of platinum films, produced by the UV-induced decomposition of organometallic materials, under various annealing conditions. The surface composition of the metal deposits was studied by X-ray photoelectron spectroscopy, both as-deposited and following thermal treatment. In addition, the morphology of the surface was studied by atomic force microscopy which enabled the investigation of film restructuring. These studies were performed over a range of temperatures up to 1000°C in air and up to 600°C in reducing environments. Complementary information regarding the film morphology has been obtained from transmission electron microscopy. The data has been used to provide an insight into the effects of elevated temperatures on metal films deposited by a direct write method

Guided Control of Cu2O Nanodot Self-Assembly on SrTiO3 (100)

2004 ◽  
Vol 811 ◽  
Author(s):  
Yingge Du ◽  
Surajit Atha ◽  
Robert Hull ◽  
James F. Groves ◽  
Igor Lyubinetsky ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Self Assembly ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Photocatalytic Decomposition ◽  
Process Conditions ◽  
Photochemical Process ◽  
Force Microscopy ◽  
Atomic Force

ABSTRACTA method has been developed for specifying the growth location of Cu2O nanodotson SrTiO3 (100) substrates. Growth location has been specified by using a focused ion beam (FIB) to modify microscopic and nanoscopic regions of the SrTiO3substrate prior to Cu2O deposition. Deposition onto the modified regions under carefully selected process conditions has generated nanodot growth at the edge of microscopic FIB-induced features and on top of nanoscopic FIB-induced features. For this work, an array of evenly spaced FIB implants was first patterned into several regions of each substrate. Within each sub-division of the array, the FIB implants were identical in Ga+ energy and dosage and implant diameter and spacing. After FIB surface modification and subsequent in-situ substrate cleaning, Cu2O nanodots were synthesized on the patterned SrTiO3 substrates using oxygen plasma assisted molecular beam epitaxy. The substrates and nanodots were characterized using atomic force microscopy at various stages of the process; in-situ X-ray photoelectron spectroscopy and Auger electron spectroscopy analysis demonstrated that the final stoichiometry of the nanodots was Cu2O. The photocatalytic decomposition of water on Cu2O under visible light irradiation has been reported. If the Cu2O can be located in the form ofislands on a carefully selected substrate, then it could be possible to greatly enhance the efficiency of the photochemical process.

Electroless Synthesis of 1.4 nm Pd and Pt Nanoparticles on Self-Assembled Rosette Nanotubes

2011 ◽  
Vol 1301 ◽  
Author(s):  
Rahul Chhabra ◽  
Hicham Fenniri
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Pt Nanoparticles ◽  
Hierarchical Organization ◽  
X Ray ◽  
Force Microscopy ◽  
Rosette Nanotubes ◽  
Atomic Force ◽  
Transmission Electron ◽  
Self Assembled

ABSTRACTElectroless synthesis and hierarchical organization of 1.4 nm Pd and Pt nanoparticles (NPs) on self-assembled Rosette Nanotubes (RNTs) is described. The nucleated NPs are nearly monodisperse and reveal supramolecular organizations guided by RNT templates. Interestingly, the narrow size distribution is attributable to unique templating behavior of RNTs. The resulting metal NP-RNT composites were characterized by Atomic Force Microscopy (AFM), Scanning Electron Microscopy (SEM) and Transmission Electron Microscopy (TEM). X-ray Photoelectron Spectroscopy (XPS) was also performed to confirm the nature and composition of RNT-templated NPs.

Sign in / Sign up

Export Citation Format

Share Document