Estimation of Firing Temperature and Compositional Variability of Archaeological Pottery by Differential Scanning Calorimetry

2004 ◽  
Vol 852 ◽  
Author(s):  
A. Giordana ◽  
E. Peacock ◽  
M. McCarthy ◽  
K. Guilbeau ◽  
P. Jacobs ◽  
...  
Keyword(s):  
Firing Temperature ◽  
Thermal Characterization ◽  
Small Sample ◽  
Scanning Calorimetry ◽  
Blind Test ◽  
Vitrification Temperature ◽  
Archaeological Pottery ◽  
Digital Scanning ◽  
Different Temperatures ◽  
Upper Estimate

ABSTRACTDigital Scanning Calorimetry (DSC), a thermal characterization technique, can be used to rapidly obtain a rough upper estimate of the firing temperature of archaeological pottery as well as an indication of its composition. The technique involves heating a small sample (10–20 mg) of ground ceramic above the vitrification temperature, cooling and reheating. The curves of the two heating cycles are then compared. The validity of the technique was evaluated by a blind test in which 35 tiles fired at different temperatures were analyzed without knowing their firing point, and by analysis of archaeological pottery samples assumed to be local or imported based upon stylistic criteria.

Mechanical and thermal characterization of grafted PP-NCC nanocomposites

2019 ◽  
pp. 089270571987822
Author(s):  
Saud Aldajah ◽  
Mohammad Y Al-Haik ◽  
Waseem Siddique ◽  
Mohammad M Kabir ◽  
Yousef Haik
Keyword(s):  
Thermal Properties ◽  
Interfacial Adhesion ◽  
Thermal Characterization ◽  
Mechanical And Thermal Properties ◽  
Screw Extruder ◽  
Scanning Calorimetry ◽  
Three Point Bending ◽  
Twin Screw ◽  
Thermal Stability Of

This study reveals the enhancement of mechanical and thermal properties of maleic anhydride-grafted polypropylene (PP- g-MA) with the addition of nanocrystalline cellulose (NCC). A nanocomposite was manufactured by blending various percentages of PP, MA, and NCC nanoparticles by means of a twin-screw extruder. The influence of varying the percentages of NCC on the mechanical and thermal behavior of the nanocomposite was studied by performing three-point bending, nanoindentation, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and Fourier-transform infrared (FTIR) spectroscopy tests. The novelty of this study stems on the NCC nanoparticles and their ability to enhance the mechanical and thermal properties of PP. Three-point bending and nanoindentation tests revealed improvement in the mechanical properties in terms of strength, modulus, and hardness of the PP- g-MA nanocomposites as the addition of NCC increased. SEM showed homogeneity between the mixtures which proved the presence of interfacial adhesion between the PP- g-MA incorporated with NCC nanoparticles that was confirmed by the FTIR results. DSC and TGA measurements showed that the thermal stability of the nanocomposites was not compromised due to the addition of the coupling agent and reinforced nanoparticles.

scholarly journals The effect of polyhedral oligomeric silsesquioxanes (POSSs) incorporation in ethylene-propylene-diene-terpolymer (EPDM): a thermal study

2021 ◽  
Author(s):  
Ignazio Blanco ◽  
Traian Zaharescu
Keyword(s):  
Room Temperature ◽  
Thermal Characterization ◽  
Polyhedral Oligomeric Silsesquioxanes ◽  
Dsc Analysis ◽  
Γ Irradiation ◽  
Scanning Calorimetry ◽  
Ethylene Propylene ◽  
Oligomeric Silsesquioxane ◽  
Ethylene Propylene Diene Terpolymer ◽  
Dynamic Heating

AbstractA series of ethylene-propylene-diene-terpolymer (EPDM)/polyhedral oligomeric silsesquioxane (POSS) composites at different percentage of POSS were prepared and subjected to γ-irradiation. Both irradiated and non-irradiated EPDM and composites were investigated by the means of thermal analysis to verify if the presence of POSS molecules is able to reduce the oxidation level of free radicals generated during the degradation and to evaluate the effects of the irradiation. EPDM composites at 1, 3 and 5 mass% of POSS were thus degraded in a thermogravimetric (TG) balance in dynamic heating conditions (25–700 °C), in both inert and oxidative atmosphere by flowing nitrogen and air respectively. Thermal characterization was then completed by carrying out Differential Scanning Calorimetry (DSC) analysis from sub-ambient to better highlight the melting of the polymer and polymer composites occurring just above the room temperature. FTIR spectroscopy was also performed for the prepared samples to check the presence of the molecular filler in the composites and for the TG’s residue at 700 °C, in order to evaluate its nature. DSC and TGA parameters were detected and discussed to have information about the effect of the degradation’s environment, the effect of irradiation on polymer stabilization and the effect of POSS content in the polymer matrix.

scholarly journals Structural, thermal and electrical properties of composites electrolytes (1−x) CsH2PO4/x ZrO2 (0 ≤ x ≤ 0.4) for fuel cell with advanced electrode

2021 ◽  
Vol 3 (1) ◽  
Author(s):  
Deshraj Singh ◽  
Pawan Kumar ◽  
Jitendra Singh ◽  
Dharm Veer ◽  
Aravind Kumar ◽  
...  
Keyword(s):  
Fuel Cell ◽  
Solid Acid ◽  
Thermal Characterization ◽  
Dihydrogen Phosphate ◽  
Conducting Material ◽  
Scanning Calorimetry ◽  
Milling Method ◽  
Thermal And Electrical Properties ◽  
Properties Of Composites

AbstractComposites proton conducting material based on cesium dihydrogen phosphate (CDP) doped with zirconium oxide (1−x) CsH2PO4/x ZrO2 were synthesized with different concentration having in the range such as x = 0.1, 0.2, 0.3 and 0.4 by ball milling method. The prepared solid acid composites were dried at 150 °C for 6 h. Structural and thermal characterization of solid acid composite proton electrolytes were carried out by X-ray diffractometer, Fourier transform infrared spectroscopy, and Raman spectroscopy respectively. Phase transition of the prepared materials was carried out by using differential scanning calorimetry and conductivity was measured by LC Impedance meter in the range 1 Hz to 400 kHz. The ionic conductivity of ZrO2 doped CsH2PO4 (CDP) was increased up to 1.3 × 10–2 S cm−1 at the 280 °C under environment atmospheric humidification which showed high stability as compared to pure CsH2PO4 (CDP). This obtaining result would be useful for establishing and design the next generation fuel cell.

Effects of additives on the cure kinetics of vinyl ester pultrusion resins

2021 ◽  
pp. 002199832110015
Author(s):  
Alexander Vedernikov ◽  
Yaroslav Nasonov ◽  
Roman Korotkov ◽  
Sergey Gusev ◽  
Iskander Akhatov ◽  
...  
Keyword(s):  
Vinyl Ester ◽  
Mean Squared Error ◽  
Cure Kinetics ◽  
Zinc Stearate ◽  
Heating Rates ◽  
Scanning Calorimetry ◽  
Different Temperatures ◽  
Predicted Values ◽  
Kinetics Of ◽  
Final Degree

Pultrusion is a highly efficient composite manufacturing process. To accurately describe pultrusion, an appropriate model of resin cure kinetics is required. In this study, we investigated cure kinetics modeling of a vinyl ester pultrusion resin (Atlac 430) in the presence of aluminum hydroxide (Al(OH)3) and zinc stearate (Zn(C18H35O2)2) as processing additives. Herein, four different resin compositions were studied: neat resin composition, composition with Al(OH)3, composition comprising Zn(C18H35O2)2, and composition containing both Al(OH)3 and Zn(C18H35O2)2. To analyze each composition, we performed differential scanning calorimetry at the heating rates of 5, 7.5, and 10 K/min. To characterize the cure kinetics of Atlac 430, 16 kinetic models were tested, and their performances were compared. The model based on the [Formula: see text]th-order autocatalytic reaction demonstrated the best results, with a 4.5% mean squared error (MSE) between the experimental and predicted data. This study proposes a method to reduce the MSE resulting from the simultaneous melting of Zn(C18H35O2)2. We were able to reduce the MSE by approximately 34%. Numerical simulations conducted at different temperatures and pulling speeds demonstrated a significant influence of resin composition on the pultrusion of a flat laminate profile. Simulation results obtained for the 600 mm long die block at different die temperatures (115, 120, 125, and 130 °C) showed that for a resin with a final degree of cure exceeding 95% at the die exit, the maximum difference between the predicted values of pulling speed for a specified set of compositions may exceed 1.7 times.

scholarly journals Synthesis and Characterization of a Multifunctional Conjugated Polymer

2018 ◽  
Vol 2018 ◽  
pp. 1-9 ◽  
Author(s):  
Emerson C. G. Campos ◽  
Cristiano Zanlorenzi ◽  
Bruno F. Nowacki ◽  
Gabriela M. Miranda ◽  
Denis A. Turchetti ◽  
...  
Keyword(s):  
Conjugated Polymer ◽  
Molar Mass ◽  
Photophysical Properties ◽  
Gel Permeation Chromatography ◽  
Thermal Characterization ◽  
Polymer Structure ◽  
Synthesis And Characterization ◽  
Metallic Ions ◽  
Scanning Calorimetry

This work reports the synthesis and characterization of a conjugated polymer based on fluorene and terpyridine, namely, poly[(9,9-bis(3-((S)-2-methylbutylpropanoate))fluorene-alt-6,6′-(2,2′:6′,2′′-terpyridin-6-yl)] (LaPPS71). The structure was characterized by 1H and 13C nuclear magnetic resonance (NMR) and Fourier-transform infrared (FTIR) spectroscopy. The molar mass was measured by gel permeation chromatography (GPC). As thermal characterization, the glass transition temperature (Tg) was measured by differential scanning calorimetry (DSC). The polymer structure contains two sites capable of complexation with metallic ions, affording the possibility of obtainment of independent or electronically coupled properties, depending on the complexation site. The photophysical properties were fully explored in solution and solid state, presenting ideal results for the preparation of various metallopolymers, in addition to potential application as a metamaterial, due to the presence of the chiral center in the side chains of the polymer.

scholarly journals THERMAL CHARACTERIZATION OF THE FAVELONE DERIVATIVES (CNIDOSCOLUS QUERCIFOLIUS) BY THERMOGRAVIMETRY AND DIFFERENTIAL SCANNING CALORIMETRY

2006 ◽  
Vol 05 (3) ◽  
pp. 8-20
Author(s):  
José Carlos Oliveira SANTOS ◽  
Lionete Dantas NUNES ◽  
Sylvia Berenice NÓBREGA ◽  
Dantas José Pires PUZINSKI ◽  
Antonio Gouveia SOUZA
Keyword(s):  
Differential Scanning Calorimetry ◽  
Arid Region ◽  
Agricultural Practices ◽  
Thermal Characterization ◽  
Northeastern Brazil ◽  
Scanning Calorimetry ◽  
Semi Arid Region ◽  
Derivatives Of ◽  
Semi Arid

A thermal analysis has been applied to characterization of food and food products. Taking into account the problems of desertification and agricultural practices able to provide income to the population at the semi-arid region of Northeastern Brazil, this work presents the results of the chemical, thermal and kinetic characterization by thermogravimetry and differential scanning calorimetry of the seed derivatives of favelone (cnidoscolus quercifolius), aiming at the application of these materials as an alternative of food source for animals and for the human population at this brazilian region.

scholarly journals Swelling properties of chitosan hydrogels

2004 ◽  
Vol 22 (1) ◽  
pp. 32 ◽  
Author(s):  
David R Rohindra ◽  
Ashveen V Nand ◽  
Jagjit R Khurma
Keyword(s):  
Differential Scanning Calorimetry ◽  
Fourier Transform ◽  
Glass Transition ◽  
Free Water ◽  
Scanning Calorimetry ◽  
Swelling Behaviour ◽  
Swelling Properties ◽  
Different Temperatures ◽  
Ft Ir ◽  
Chitosan Hydrogels

Chitosan hydrogels were prepared by crosslinking chitosan with glutaraldehyde. The swelling behaviour of the crosslinked and uncross-linked hydrogels was measured by swelling the gels in media of different pH and at different temperatures. The swelling behavior was observed to be dependent on pH, temperature and the degree of crosslinking. The gel films were characterized by Fourier transform Infrared spectroscopy (FT-IR) and Differential Scanning Calorimetry (DSC). The glass transition temperature (Tg) and the amount of free water in the hydrogels decreased with increasing crosslinking in the hydrogels.

scholarly journals Preparation and Characterization of Polymer Composite Materials Based on PLA/TiO2 for Antibacterial Packaging

Polymers ◽  
2018 ◽  
Vol 10 (12) ◽  
pp. 1365 ◽  
Author(s):  
Edwin A. Segura González ◽  
Dania Olmos ◽  
Miguel Ángel Lorente ◽  
Itziar Vélaz ◽  
Javier González-Benito
Keyword(s):  
Composite Materials ◽  
Tio2 Nanoparticles ◽  
Polymer Composite ◽  
Bacterial Growth ◽  
Thermal Characterization ◽  
Polymer Composite Materials ◽  
Thermal Transitions ◽  
Scanning Calorimetry ◽  
Particle Content ◽  
Fourier Transformed Infrared Spectroscopy

Polymer composite materials based on polylactic acid (PLA) filled with titanium dioxide (TiO2) nanoparticles were prepared. The aim of this work was to investigate the antibacterial action of TiO2 against a strain of E. Coli (DH5α) to obtain information on their potential uses in food and agro-alimentary industry. PLA/TiO2 systems were prepared by a two-step process: Solvent casting followed by a hot-pressing step. Characterization was done as a function of particle size (21 nm and < 100 nm) and particle content (0%, 1%, 5%, 10%, and 20%, wt %). Structural characterization carried out by X-ray diffraction (XRD) and Fourier Transformed Infrared spectroscopy (FTIR) did not reveal significant changes in polymer structure due to the presence of TiO2 nanoparticles. Thermal characterization indicated that thermal transitions, measured by differential scanning calorimetry (DSC), did not vary, irrespective of size or content, whereas thermogravimetric analysis (TGA) revealed a slight increase in the temperature of degradation with particle content. Bacterial growth and biofilm formation on the surface of the composites against DH5α Escherichia Coli was studied. Results suggested that the presence of TiO2 nanoparticles decreases the amount of extracellular polymeric substance (EPS) and limits bacterial growth. The inhibition distances estimated with the Kirby-Bauer were doubled when 1% TiO2 nanoparticles were introduced in PLA, though no significant differences were obtained for higher contents in TiO2 NPs.

scholarly journals Not Reacted Core Model Applied in Palm Nut Shell Pyrolysis

2019 ◽  
Vol 2019 ◽  
pp. 1-8
Author(s):  
Ernesto de la Torre ◽  
Sebastián Gámez
Keyword(s):  
Kinetic Parameters ◽  
Elaeis Guineensis ◽  
Effective Diffusion ◽  
Reaction Rate Constant ◽  
Core Model ◽  
Scanning Calorimetry ◽  
Differential Scanning Calorimetry Study ◽  
Different Temperatures ◽  
Char Conversion ◽  
Pyrolysis Of Biomass

One of the main sources of activated carbon is biomass which can be transformed into char by pyrolysis. Apart from the obtaining coal, the pyrolysis of biomass can be used for the preparation of fuels, and this is why it is very important to determine its kinetic parameters for modelling. In the present research, the pyrolysis enthalpy of palm nut shells (Elaeis guineensis) was determined with the use of a differential scanning calorimetry study (DSC). To determine the kinetic parameters, the Not Reacted Core model was employed. This model considers that there is a heat and mass gradient between the furnace atmosphere and the interface formed during pyrolysis. To obtain the required data for the model, palm nut shells were submitted to pyrolysis in a Nichols furnace under reducing atmosphere. Samples were taken every 10 minutes to calculate char conversion. The experimental pyrolysis enthalpy resulted to be 301.81 J/g and then the monomeric units of cellulose, hemicellulose, and lignin were employed in order to determine the pyrolysis enthalpy per mole. The three biopolymers react with different mechanisms at different temperatures. The molecular weight resulted to be 172.38 g/mole, and the enthalpy for pyrolysis was 52.03 kJ/mol. For the application of the Not Reacted Core model, the amorphous char heat transfer coefficient was selected, and the value is 1.6 J/s·m·K. The reaction rate constant was 6.64 × 10−9 1/s assuming a first-order reaction, whereas the effective diffusion across the char layer was 4.83 × 10−7 m2/s.

Sign in / Sign up

Export Citation Format

Share Document