Heat transfer in HF induction plasmatron VGU-4 with the use of slit nozzles

2020 ◽  
Author(s):  
A.N. Gordeev ◽  
A.V. Chaplyguin
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Fluxes ◽  
Nozzle Geometry ◽  
Outlet Section ◽  
Plate Surface ◽  
Catalytic Surface ◽  
Induction Plasmatron ◽  
Axis Of Symmetry ◽  
Heat Shielding

Heat transfer of subsonic jets of dissociated gas flowing from slit nozzles with outlet sections of 40 × 8, 80 × 15 and 120 × 9 mm with the plate surface at an angle of attack was experimentally studied in the HF-plasmatron VGU-4. Heat flux distributions along the axis of symmetry of the copper plates were obtained depending on the power of the anode supply of the HF-generator and the slit nozzle geometry. Heat fluxes on the low-catalytic surface of the heat-shielding tile of the «Buran» orbiter were determined depending on the pressure in the plasmatron chamber when using a slit nozzle with an outlet section of 120 × 9 mm.

scholarly journals Assessing IDDES-Based Wall-Modeled Large-Eddy Simulation (WMLES) for Separated Flows with Heat Transfer

Fluids ◽  
2021 ◽  
Vol 6 (7) ◽  
pp. 246
Author(s):  
Rozie Zangeneh
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Large Eddy Simulation ◽  
Skin Friction ◽  
Heat Fluxes ◽  
Separated Flows ◽  
Detached Eddy Simulation ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Isothermal Wall

The Wall-modeled Large-eddy Simulation (WMLES) methods are commonly accompanied with an underprediction of the skin friction and a deviation of the velocity profile. The widely-used Improved Delayed Detached Eddy Simulation (IDDES) method is suggested to improve the prediction of the mean skin friction when it acts as WMLES, as claimed by the original authors. However, the model tested only on flow configurations with no heat transfer. This study takes a systematic approach to assess the performance of the IDDES model for separated flows with heat transfer. Separated flows on an isothermal wall and walls with mild and intense heat fluxes are considered. For the case of the wall with heat flux, the skin friction and Stanton number are underpredicted by the IDDES model however, the underprediction is less significant for the isothermal wall case. The simulations of the cases with intense wall heat transfer reveal an interesting dependence on the heat flux level supplied; as the heat flux increases, the IDDES model declines to predict the accurate skin friction.

Heat Transfer to Supercritical Water in Vertical Annular Channel and 3-Rod Bundle

2009 ◽  
Author(s):  
V. G. Razumovskiy ◽  
Eu. N. Pis’mennyy ◽  
A. Eu. Koloskov ◽  
I. L. Pioro
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Supercritical Water ◽  
Annular Channel ◽  
Heat Fluxes ◽  
Inlet Temperature ◽  
Outlet Temperature ◽  
Rod Bundle ◽  
Temperature Regimes ◽  
Outside Diameter

The results of heat transfer to supercritical water flowing upward in a vertical annular channel (1-rod channel) and tight 3-rod bundle consisting of the tubes of 5.2-mm outside diameter and 485-mm heated length are presented. The heat-transfer data were obtained at pressures of 22.5, 24.5, and 27.5 MPa, mass flux within the range from 800 to 3000 kg/m2·s, inlet temperature from 125 to 352°C, outlet temperature up to 372°C and heat flux up to 4.6 MW/m2 (heat flux rate up to 2.5 kJ/kg). Temperature regimes of the annular channel and 3-rod bundle were stable and easily reproducible within the whole range of the mass and heat fluxes, even when a deteriorated heat transfer took place. The data resulted from the study could be applicable for a reference estimation of heat transfer in future designs of fuel bundles.

Heat Transfer Enhancement in Compact Phase Change Microchannel Heat Exchangers for High Flux Laser Diodes

2018 ◽  
Author(s):  
Jensen Hoke ◽  
Todd Bandhauer ◽  
Jack Kotovsky ◽  
Julie Hamilton ◽  
Paul Fontejon
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Phase Change ◽  
Flow Boiling ◽  
Laser Diodes ◽  
High Heat ◽  
Heat Fluxes ◽  
High Heat Flux ◽  
Maximum Heat ◽  
Average Maximum

Liquid-vapor phase change heat transfer in microchannels offers a number of significant advantages for thermal management of high heat flux laser diodes, including reduced flow rates and near constant temperature heat rejection. Modern laser diode bars can produce waste heat loads >1 kW cm−2, and prior studies show that microchannel flow boiling heat transfer at these heat fluxes is possible in very compact heat exchanger geometries. This paper describes further performance improvements through area enhancement of microchannels using a pyramid etching scheme that increases heat transfer area by ∼40% over straight walled channels, which works to promote heat spreading and suppress dry-out phenomenon when exposed to high heat fluxes. The device is constructed from a reactive ion etched silicon wafer bonded to borosilicate to allow flow visualization. The silicon layer is etched to contain an inlet and outlet manifold and a plurality of 40μm wide, 200μm deep, 2mm long channels separated by 40μm wide fins. 15μm wide 150μm long restrictions are placed at the inlet of each channel to promote uniform flow rate in each channel as well as flow stability in each channel. In the area enhanced parts either a 3μm or 6μm sawtooth pattern was etched vertically into the walls, which were also scalloped along the flow path with the a 3μm periodicity. The experimental results showed that the 6μm area-enhanced device increased the average maximum heat flux at the heater to 1.26 kW cm2 using R134a, which compares favorably to a maximum of 0.95 kw cm2 dissipated by the plain walled test section. The 3μm area enhanced test sections, which dissipated a maximum of 1.02 kW cm2 showed only a modest increase in performance over the plain walled test sections. Both area enhancement schemes delayed the onset of critical heat flux to higher heat inputs.

Radiation and Convection Heat Transfer in a Porous Bed

1968 ◽  
Vol 90 (1) ◽  
pp. 51-54 ◽  
Author(s):  
W. A. Beckman
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Collection Efficiency ◽  
Convection Heat Transfer ◽  
Heat Fluxes ◽  
Fluid Temperature ◽  
Radiation Heat ◽  
Radiation Heat Flux ◽  
Flowing Fluid ◽  
Porous Bed

The one-dimensional steady-state temperature distribution within an isotropic porous bed subjected to a collimated and/or diffuse radiation heat flux and a transparent flowing fluid has been determined by numerical methods. The porous bed was assumed to be nonscattering and to have a constant absorption coefficient. Part of the radiation absorbed by the porous bed is reradiated and the remainder is transferred to the fluid by convection. Due to the assumed finite volumetric heat transfer coefficient, the bed and fluid have different temperatures. A bed with an optical depth of six and with a normal incident collimated radiation heat flux was investigated in detail. The radiation incident on the bed at the fluid exit was assumed to originate from a black surface at the fluid exit temperature. The investigation covered the range of incident diffuse and collimated radiation heat fluxes expected in a nonconcentrating solar energy collector. The results are presented in terms of a bed collection efficiency from which the fluid temperature rise can be calculated.

Experimental Study of Heat Transfer to Supercritical Pressure Water Flowing in a 2×2 Rod Bundle

2014 ◽  
Author(s):  
Han Wang ◽  
Qincheng Bi ◽  
Linchuan Wang ◽  
Haicai Lv ◽  
Laurence K. H. Leung
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Heat Flux ◽  
Pressure Drop ◽  
Wall Temperature ◽  
Mass Flux ◽  
Heat Fluxes ◽  
Outer Diameter ◽  
Square Channel ◽  
Rod Bundle

An experiment has recently been performed at Xi’an Jiaotong University to study the wall temperature and pressure drop at supercritical pressures with upward flow of water inside a 2×2 rod bundle. A fuel-assembly simulator with four heated rods was installed inside a square channel with rounded corner. The outer diameter of each heated rod is 8 mm with an effective heated length of 600 mm. Experimental parameters covered the pressure of 23–28 MPa, mass flux of 350–1000 kg/m2s and heat flux on the rod surface of 200–1000 kW/m2. According to the experimental data, it was found that the circumferential wall temperature distribution of a heated rod is not uniform. The temperature difference between the maximum and the minimum varies with heat flux and/or mass flux. Heat transfer characteristics of supercritical water in bundle were discussed with respect to various heat fluxes. The effect of heat flux on heat transfer in rod bundles is similar with that in tubes or annuli. In addition, flow resistance reflected in the form of pressure loss has also been studied. Experimental results showed that the total pressure drop increases with bulk enthalpy and mass flux. Four heat transfer correlations developed for supercritical pressures water were compared with the present test data. Predictions of Jackson correlation agrees closely with the experimental data.

Mixed Convection in a Vertical Parallel Plate Microchannel With Asymmetric Wall Heat Fluxes

2006 ◽  
Vol 129 (8) ◽  
pp. 1091-1095 ◽  
Author(s):  
Mete Avcı ◽  
Orhan Aydın
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Mixed Convection ◽  
Convective Heat Transfer ◽  
Parallel Plate ◽  
Temperature Jump ◽  
Velocity Slip ◽  
Heat Fluxes ◽  
Limiting Case ◽  
Convection Parameter

In this study, exact analytical results are presented for fully developed mixed convective heat transfer of a Newtonian fluid in an open-ended vertical parallel plate microchannel with asymmetric wall heating at uniform heat fluxes. The velocity slip and the temperature jump at the wall are included in the formulation. The effects of the modified mixed convection parameter, Grq∕Re, the Knudsen number, Kn, and the ratio of wall heat flux, rq=q1∕q2, on the microchannel hydrodynamic and thermal behaviors are determined. Finally, a Nu=f(Grq∕Re,Kn,rq) expression is developed. For, the limiting case of Kn=0, the results are found to be in an excellent agreement with those in the existing literature.

Stability and Enhancement of Boiling in Microchannels

2011 ◽  
Author(s):  
A. E. Bergles
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Critical Heat Flux ◽  
High Heat ◽  
Heat Fluxes ◽  
Transfer Enhancement ◽  
The Past ◽  
The Stability ◽  
Saturated Boiling ◽  
Microelectronic Components

During the past 20 years, there has been intense worldwide interest in microchannel heat exchangers, particularly for cooling of microelectronic components. Saturated boiling of the coolant is usually indicated in order to accommodate high heat fluxes and to have uniformity of temperature. However, boiling is accompanied by several instabilities, the most severe of which can sharply limit the maximum, or critical, heat flux. These stability phenomena are reviewed, and recent studies will be discussed. Elevation of the critical heat flux will be discussed within the context of heat transfer enhancement. Means to improve the stability of boiling and the enhancement of boiling heat transfer, in general, are discussed.

scholarly journals Deterioration in Heat Transfer to Fluids at Supercritical Pressure and High Heat Fluxes

1969 ◽  
Vol 91 (1) ◽  
pp. 27-36 ◽  
Author(s):  
B. S. Shiralkar ◽  
Peter Griffith
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
High Heat ◽  
Supercritical Pressure ◽  
Heat Fluxes ◽  
Bulk Temperature ◽  
Operating Pressure ◽  
The Heat Transfer Coefficient

At slightly supercritical pressure and in the neighborhood of the pseudocritical temperature (which corresponds to the peak in the specific heat at the operating pressure), the heat transfer coefficient between fluid and tube wall is strongly dependent on the heat flux. For large heat fluxes, a marked deterioration takes place in the heat transfer coefficient in the region where the bulk temperature is below the pseudocritical temperature and the wall temperature above the pseudocritical temperature. Equations have been developed to predict the deterioration in heat transfer at high heat fluxes and the results compared with previously available results for steam. Experiments have been performed with carbon dioxide for additional comparison. Limits of safe operation for a supercritical pressure heat exchanger in terms of the allowable heat flux for a particular flow rate have been determined theoretically and experimentally.

Experimental Study of a Single Microchannel Flow Under Non-Uniform Heat Flux

2017 ◽  
Author(s):  
Ahmed Eltaweel ◽  
Abdulla Baobeid ◽  
Ibrahim Hassan
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Dissipation ◽  
Hot Spot ◽  
Heat Fluxes ◽  
Heat Sinks ◽  
Uniform Heat Flux ◽  
Maximum Heat ◽  
Uniform Heat ◽  
Microchannel Heat Sinks

Non-uniform heat fluxes are commonly observed in thermo-electronic devices that require distinct thermal management strategies for effective heat dissipation and robust performance. The limited research available on non-uniform heat fluxes focus mostly on microchannel heat sinks while the fundamental component, i.e. a single microchannel, has received restricted attention. In this work, an experimental setup for the analysis of variable axial heat flux is used to study the heat transfer in a single microchannel with fully developed flow under the effect of different heat flux profiles. Initially a hot spot at different locations, with a uniform background heat flux, is studied at different Reynolds numbers while varying the maximum heat fluxes in order to compute the heat transfer in relation to its dependent variables. Measurements of temperature, pressure, and flow rates at a different locations and magnitudes of hot spot heat fluxes are presented, followed by a detailed analysis of heat transfer characteristics of a single microchannel under non-uniform heating. Results showed that upstream hotspots have lower tube temperatures compared to downstream ones with equal amounts of heat fluxes. This finding can be of importance in enhancing microchannel heat sinks effectiveness in reducing maximum wall temperatures for the same amount of heat released, by redistributing spatially fluxes in a descending profile.

Experimental and numerical simulation studies on heat transfer to calorimeters engulfed in diesel pool fires

2017 ◽  
Vol 35 (2) ◽  
pp. 156-176 ◽  
Author(s):  
Sudheer Siddapureddy ◽  
SV Prabhu
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Surface Temperature ◽  
Heat Fluxes ◽  
Numerical Code ◽  
Pool Fires ◽  
Steel Pipes ◽  
Adiabatic Surface ◽  
In Fire ◽  
Good Agreement

Characterization of heat transfer to calorimeters engulfed in pool fires is extremely important. To estimate the heat flux to the calorimeters, experiments are performed with horizontal stainless steel 304L pipes engulfed in diesel pool fires. The concept of adiabatic surface temperature is applied to predict the incident heat flux to horizontally oriented calorimeters engulfed in diesel pool fires. Plate thermometers are used to measure the adiabatic surface temperature for diesel pool fires. The estimated subsurface temperatures inside the steel pipes using the adiabatic surface temperature concept and the measured temperatures are in good agreement. Adiabatic surface temperature is also computed from fire simulations. The incident heat fluxes to the steel pipes engulfed in fire predicted from the simulations are found to be in good agreement with the experiments. The fire numerical code is validated against the 1 m pool fire experimental results of centerline temperature distribution and irradiances away from fire. A correlation is provided for the estimation of adiabatic surface temperature for large diesel pool fires. These results would provide an effective way for thermal test simulations.

Sign in / Sign up

Export Citation Format

Share Document