A Nano Method for a Big Challenge: Nanosilica-Based Sealing System for Water Shutoff

2021 ◽  
Author(s):  
Ayman Almohsin ◽  
Jin Hung ◽  
Mohammed Alabdrabalnabi ◽  
Mohammed Sherief
Keyword(s):  
Chemical Treatment ◽  
Fractured Reservoirs ◽  
Gelation Time ◽  
Cost Effective ◽  
Economic Life ◽  
Narrow Particle Size Distribution ◽  
Water Production ◽  
Water Shutoff ◽  
Sandstone Rock ◽  
Wide Range

Abstract Minimizing unwanted water production from oil wells is highly required in the petroleum industry. This would lead to improved economic life of mature wells that involve new and innovative technologies. Nanosilica-based sealing fluid has been developed to address problems associated with unwanted water production. The objective of this work is to evaluate a newly developed novel water shutoff system based on nanosilica over a wide range of parameters. This modified nanosilica has a smooth, spherical shape, and are present in a narrow particle size distribution. Therefore, it can be used for water management in different water production mechanisms including high permeability streak, wormhole, and fractured reservoirs. A systematic evaluation of novel nanosilica/activator for water shutoff purposes requires the examination of the chemical properties before, during, and after gelation at given reservoir conditions. These properties are solution initial viscosity, gelation time, injectivity, and strength of the formed gel against applied external forces in different flooding systems. This paper details a promising method to control undesired water production using eco-friendly, cost-effective nanosilica. Experimental results revealed that nanosilica initially exhibited a low viscosity and hence providing a significant advantage in terms of mixing and pumping requirements. Nanosilica gelation time, which is a critical factor in placement of injected-chemical treatment, can be tailored by adjusting the activator concentration to match field requirements at the desired temperature. In addition, core flood tests were conducted in carbonate core plugs, Berea sandstone rock, and artificially fractured (metal tube) to investigate the performance of the chemical treatment. Flow tests clearly indicated that the water production significantly dropped in all tested types of rocks. The environmental scanning electron microscope (SEM) results showed the presence of SiO-rich compounds suggesting that the tested nanosilica product filled the porous media; therefore, it blocked the whole core plug. A novel cost-effective sealant that uses nanotechnology to block the near wellbore region has been developed. The performance and methods controlling its propagation rate into a porous medium will be presented. Based on the outcomes, it must be emphasized that these trivial particles have a promising application in the oil reservoir for water shutoff purposes.

Evaluation of Foam-Gels for Conformance Control in High Temperature High Salinity Carbonates

2021 ◽  
Author(s):  
Lyla Almaskeen ◽  
Abdulkareem AlSofi ◽  
Jinxun Wang ◽  
Ziyad Kaidar
Keyword(s):  
High Temperature ◽  
Oil Recovery ◽  
Concentration Ratio ◽  
High Salinity ◽  
Fractured Reservoirs ◽  
Gelation Time ◽  
Resistance Factor ◽  
Naturally Fractured Reservoirs ◽  
Conformance Control ◽  
Wide Range

Abstract In naturally fractured reservoirs, conformance control prior to enhanced oil recovery (EOR) application might be essential to ensure optimal contact and sufficient sweep. Recently, few studies investigated combining foams and gels into what is commonly coined as foamed-gels. Foamed-gels have been tested and shown to be potential for some field conditions. Yet, very limited studies were performed for high temperature and high salinity carbonates. Therefore, in this work, we study the potential of foamed-gels for high temperature and high salinity carbonates. The objective is to evaluate the potential of such synergy and to compare its value to the individual processes. For that purpose, in this work, we rely on bulk and core-scale tests. Bulk tests were used for initial screening. Wide range of foam-gel solutions were prepared with different polymer types and polymer concentrations. Test tubes were hand shacked thoroughly to generate foams. Foam heights were then measured from the test tubes. Heights were used to screen foaming agents and to study gelant effects on foamers in terms of foam strength (heights). The effect of foamers on gelation was evaluated through bottle tests. Based on the results, an optimal concentration ratio of gelant to foamer was determined and used in core-scale displacements, to further study the potential of this hybrid foam-gel process. Bulk results suggested that addition of the gelant up to a 4:1 foam to gel concentration ratio resulted in sufficient foam generation in some of the polymer samples. Yet, only two of the foam-gel samples generated a strong gel. Increasing the foamer concentration delayed the gelation time and in some samples, the solution did not gel. Through the coreflooding experiment, resistance factor (RF) and residual resistance factor (RRF) were obtained for different conformance control processes including foam, foam-gel, and gel. Foam-gel injection exhibited higher RF and RRF values than conventional foams. However, conventional gels showed even higher RF and RRF values than foam-gels. Combining two of the most widely used conformance control methods (foams and gels) can strike a balance. Foam-gel may offer a treatment that is deeper and more sustainable than foams and on the other a treatment that is more practical, and lower-cost than gels. Our laboratory results also demonstrate that such synergetic conformance control can be achieved in high salinity and high temperature carbonates with pronounced impact.

Experimental Investigation of a Novel Nanosilica for Blocking Unwanted Water Production

2021 ◽  
Author(s):  
Mohammed Alabdrabalnabi ◽  
Ayman Almohsin ◽  
Jin Huang ◽  
Mohammed Sherief
Keyword(s):  
Oil And Gas ◽  
Fractured Reservoirs ◽  
Gelation Time ◽  
Chemical Properties ◽  
Oil And Gas Industry ◽  
Engineered Nanoparticles ◽  
Systematic Evaluation ◽  
Water Production ◽  
Exponential Relationship ◽  
Initial Viscosity

Abstract Nanotechnology is the design and application of engineered nanoparticles with one minimum dimension in the range of 1 to 100 nanometers. To achieve a specific target, innovative methods are highly required to overcome the challenges in the oil and gas industry, such as undesired water production. Herein, we present an advanced nanosilica, a new eco-friendly, cost-effective, and promising approach to control undesirable water production. The objective of this work is to evaluate our nanofluid system that can be used for water management in different water production mechanisms, including: high permeability streak, wormhole, and fractured reservoirs. A systematic evaluation of novel nanosilica/activator for water shut-off application requires an examination of the chemical properties before, during, and after gelation at given reservoir conditions. The placement of this water shut-off system is highly dependent on gelation time and viscosity. Therefore, we emphasized in this study on investigating these gelation kinetics by conducting extensive rheology experiments at varied temperatures and activator concentrations. We have looked into evaluating the optimum breaker for the gel as a contingency plan for improper placement. Measurements of the nanosilica fluid’s initial viscosity exhibited a low viscosity, less than 10 cP at normal temperature and pressure (NTP) conditions; this provides significant benefit for mixing at surface and pumping requirements for pilot testing. The nanosilica gelation time can be tailored by adjusting activator concentration to match field job design at a given temperature, which is more than 200°F. The gelation time revealed an exponential relationship with temperature and reversible proportionality. The nanosilica gel proved to be a thermally stable fluid system along with different activation ratios. For breaker tests, the gellant fluid showed complete breakdown at altered temperatures to mimic downhole conditions. Our lab observations conclude that nanosilica fluid is verified to be acceptable as a water shut-off system for field applications. This novel nanofluid system is a promising technology to control water production from oil wells. The system has low initial viscosity that can be injected in porous media without hindering the injectivity and getting at risk of fracking the sand. In case of inappropriate placement, the fluid can break down entirely using a non-damaging chemical breaker instead of using mechanical approaches that might damage the completion.

Polymer Systems for Water Shutoff and Profile Modification: A Review Over the Last Decade

SPE Journal ◽  
2013 ◽  
Vol 19 (01) ◽  
pp. 135-149 ◽  
Author(s):  
Khalid Saad El-Karsani ◽  
Ghaithan A. Al-Muntasheri ◽  
Ibnelwaleed A. Hussein
Keyword(s):  
Oil And Gas ◽  
Water Injection ◽  
Gelation Time ◽  
Field Application ◽  
Injection Wells ◽  
Polyelectrolyte Complexes ◽  
Polymer Systems ◽  
Water Shutoff ◽  
Wide Range ◽  
Hydrolyzed Polyacrylamide

Summary Unwanted water production is a serious issue in oil- and gas-producing wells. It causes corrosion, scale, and loss of productivity. One method of treating this problem is to chemically reduce unwanted water. This paper discusses the use of polymer systems for this purpose and presents a thorough review of available literature over the last decade. In this paper, field-application data for various polymer systems are summarized over the range of 40 to 150°C (104 to 302°F). These applications cover a wide range of permeabilities from 20 to 2,720 md in sandstone and carbonate reservoirs around the globe. Moreover, the review revealed that the last decade of developments can be categorized into two major types. The first type is polymer gels for total water shutoff in the near-wellbore region, in which a polymer is crosslinked with either an organic or an inorganic crosslinker. The second type is concerned with deep treatment of water-injection wells diverting fluids away from high-permeability zones (thief zones). These thief zones take most of the injected water, which results in a large amount of unrecovered oil. For the total-blocking gels, various systems were identified, such as polyurethane resins, chromium (Cr3+) crosslinking terpolymers, Cr3+ crosslinking foamed partially hydrolyzed polyacrylamide (PHPA), and nanoparticle polyelectrolyte complexes (PECs) sequestering Cr3+ for elongation of its gelation time with PHPA. In addition, polyethylenimine (PEI) was identified to crosslink various polyacrylamide- (PAM-) based polymers. The Petróleos de Venezuela S.A. (PDVSA) Research and Development Center developed a PAM-based thermally stable polymer and an organic crosslinker. The system is applicable for a wide temperature range from 50 to 160°C (130 to 320°F). For the deep modification of water-injection profiles in water-injection wells, two systems were identified: microspheres prepared from PAM monomers crosslinked with N,N′-methylenebisacrylamide and microspheres produced by crosslinking 2-acrylamido-2-methylpropane sulfonic acid (AMPS) with diacrylamides and methacrylamides of diamines (thermally activated microparticles known as Bright Water). This paper highlights all major developments in these areas.

2D Color-Intensity Representation of Ultrasonic Thickness Gauge Measurements

2020 ◽  
pp. 1192-1198
Author(s):  
M.S. Mohammad ◽  
Tibebe Tesfaye ◽  
Kim Ki-Seong
Keyword(s):  
Cost Effective ◽  
The Other ◽  
Thickness Gauge ◽  
Color Intensity ◽  
Digital Readout ◽  
Flat Surfaces ◽  
Video Cameras ◽  
Wide Range ◽  
Cost Effective Alternative ◽  
Ultrasonic Thickness

Ultrasonic thickness gauges are easy to operate and reliable, and can be used to measure a wide range of thicknesses and inspect all engineering materials. Supplementing the simple ultrasonic thickness gauges that present results in either a digital readout or as an A-scan with systems that enable correlating the measured values to their positions on the inspected surface to produce a two-dimensional (2D) thickness representation can extend their benefits and provide a cost-effective alternative to expensive advanced C-scan machines. In previous work, the authors introduced a system for the positioning and mapping of the values measured by the ultrasonic thickness gauges and flaw detectors (Tesfaye et al. 2019). The system is an alternative to the systems that use mechanical scanners, encoders, and sophisticated UT machines. It used a camera to record the probe’s movement and a projected laser grid obtained by a laser pattern generator to locate the probe on the inspected surface. In this paper, a novel system is proposed to be applied to flat surfaces, in addition to overcoming the other limitations posed due to the use of the laser projection. The proposed system uses two video cameras, one to monitor the probe’s movement on the inspected surface and the other to capture the corresponding digital readout of the thickness gauge. The acquired images of the probe’s position and thickness gauge readout are processed to plot the measured data in a 2D color-coded map. The system is meant to be simpler and more effective than the previous development.

Use of ultrasonic surface hardening in modifi cation of surface layer

2020 ◽  
pp. 200-204
Author(s):  
Yu.S. Semenova ◽  
A.G. Samul’ ◽  
S.V. Mazhuga
Keyword(s):  
Surface Layer ◽  
Chemical Treatment ◽  
Surface Hardening ◽  
Manufacturing Cost ◽  
Ultrasonic Vibrations ◽  
Surface Microrelief ◽  
Scientific Schools ◽  
Structure Changes ◽  
Wide Range ◽  
Finishing Machining

Overview of the research results got by various scientific schools in the field of application of ultrasonic surface hardening is provided. Wide range of opportunities of ultrasonic surface hardening is shown for the application in the preliminary machining of surfaces before thermal and chemical treatment, coating, and also as finishing machining. The effect of the energy of ultrasonic vibrations on structure changes in the material of the surface layer and on surface microrelief on parts performance is considered. The prospects of using of the ultrasonic surface hardening method in combination with other methods of the material modification are presented. In addition the possibilities of reducing the manufacturing cost of product by introducing ultrasonic surface hardening into the technological process are shown.

Coagulation/flocculation/ultrafiltration for natural organic matter removal in drinking water production

2004 ◽  
Vol 4 (5-6) ◽  
pp. 215-222 ◽  
Author(s):  
A.R. Costa ◽  
M.N. de Pinho
Keyword(s):  
Drinking Water ◽  
Organic Matter ◽  
Natural Organic Matter ◽  
Membrane Fouling ◽  
Membrane Filtration ◽  
Membrane Surface ◽  
Water Production ◽  
Cellulose Acetate Membranes ◽  
Wide Range ◽  
Drinking Water Production

Membrane fouling by natural organic matter (NOM), namely by humic substances (HS), is a major problem in water treatment for drinking water production using membrane processes. Membrane fouling is dependent on membrane morphology like pore size and on water characteristics namely NOM nature. This work addresses the evaluation of the efficiency of ultrafiltration (UF) and Coagulation/Flocculation/UF performance in terms of permeation fluxes and HS removal, of the water from Tagus River (Valada). The operation of coagulation with chitosan was evaluated as a pretreatment for minimization of membrane fouling. UF experiments were carried out in flat cells of 13.2×10−4 m2 of membrane surface area and at transmembrane pressures from 1 to 4 bar. Five cellulose acetate membranes were laboratory made to cover a wide range of molecular weight cut-off (MWCO): 2,300, 11,000, 28,000, 60,000 and 75,000 Da. Severe fouling is observed for the membranes with the highest cut-off. In the permeation experiments of raw water, coagulation prior to membrane filtration led to a significant improvement of the permeation performance of the membranes with the highest MWCO due to the particles and colloidal matter removal.

The Future of Plasma-Based Surface Engineering Techniques in Tribology (Keynote)

2005 ◽  
Author(s):  
Allan Matthews ◽  
Adrian Leyland
Keyword(s):  
Surface Engineering ◽  
Performance Enhancement ◽  
Bulk Material ◽  
Cost Savings ◽  
Cost Effective ◽  
Ceramic Coatings ◽  
Performance Improvements ◽  
Treatment Techniques ◽  
Wide Range ◽  
Macro Scale

Over the past twenty years or so, there have been major steps forward both in the understanding of tribological mechanisms and in the development of new coating and treatment techniques to better “engineer” surfaces to achieve reductions in wear and friction. Particularly in the coatings tribology field, improved techniques and theories which enable us to study and understand the mechanisms occurring at the “nano”, “micro” and “macro” scale have allowed considerable progress to be made in (for example) understanding contact mechanisms and the influence of “third bodies” [1–5]. Over the same period, we have seen the emergence of the discipline which we now call “Surface Engineering”, by which, ideally, a bulk material (the ‘substrate’) and a coating are combined in a way that provides a cost-effective performance enhancement of which neither would be capable without the presence of the other. It is probably fair to say that the emergence and recognition of Surface Engineering as a field in its own right has been driven largely by the availability of “plasma”-based coating and treatment processes, which can provide surface properties which were previously unachievable. In particular, plasma-assisted (PA) physical vapour deposition (PVD) techniques, allowing wear-resistant ceramic thin films such as titanium nitride (TiN) to be deposited on a wide range of industrial tooling, gave a step-change in industrial productivity and manufactured product quality, and caught the attention of engineers due to the remarkable cost savings and performance improvements obtained. Subsequently, so-called 2nd- and 3rd-generation ceramic coatings (with multilayered or nanocomposite structures) have recently been developed [6–9], to further extend tool performance — the objective typically being to increase coating hardness further, or extend hardness capabilities to higher temperatures.

scholarly journals Gamma models for estimating the odds ratio for a skewed biomarker measured in pools and subject to errors

Biostatistics ◽  
2019 ◽  
Author(s):  
Dane R Van Domelen ◽  
Emily M Mitchell ◽  
Neil J Perkins ◽  
Enrique F Schisterman ◽  
Amita K Manatunga ◽  
...  
Keyword(s):  
Odds Ratio ◽  
Adjusted Odds Ratio ◽  
Lower Cost ◽  
Cost Effective ◽  
Ratio Estimation ◽  
Statistical Efficiency ◽  
Function Model ◽  
Processing Error ◽  
Wide Range ◽  
Pooled Samples

SUMMARYMeasuring a biomarker in pooled samples from multiple cases or controls can lead to cost-effective estimation of a covariate-adjusted odds ratio, particularly for expensive assays. But pooled measurements may be affected by assay-related measurement error (ME) and/or pooling-related processing error (PE), which can induce bias if ignored. Building on recently developed methods for a normal biomarker subject to additive errors, we present two related estimators for a right-skewed biomarker subject to multiplicative errors: one based on logistic regression and the other based on a Gamma discriminant function model. Applied to a reproductive health dataset with a right-skewed cytokine measured in pools of size 1 and 2, both methods suggest no association with spontaneous abortion. The fitted models indicate little ME but fairly severe PE, the latter of which is much too large to ignore. Simulations mimicking these data with a non-unity odds ratio confirm validity of the estimators and illustrate how PE can detract from pooling-related gains in statistical efficiency. These methods address a key issue associated with the homogeneous pools study design and should facilitate valid odds ratio estimation at a lower cost in a wide range of scenarios.

scholarly journals Sporulation in solventogenic and acetogenic clostridia

2021 ◽  
Author(s):  
Mamou Diallo ◽  
Servé W. M. Kengen ◽  
Ana M. López-Contreras
Keyword(s):  
Current Knowledge ◽  
Carbon Sources ◽  
Cost Effective ◽  
Biotechnological Production ◽  
Key Points ◽  
Wide Range ◽  
Potential Applications ◽  
A Cell ◽  
Sporulation Initiation ◽  
Solventogenic Clostridia

AbstractThe Clostridium genus harbors compelling organisms for biotechnological production processes; while acetogenic clostridia can fix C1-compounds to produce acetate and ethanol, solventogenic clostridia can utilize a wide range of carbon sources to produce commercially valuable carboxylic acids, alcohols, and ketones by fermentation. Despite their potential, the conversion by these bacteria of carbohydrates or C1 compounds to alcohols is not cost-effective enough to result in economically viable processes. Engineering solventogenic clostridia by impairing sporulation is one of the investigated approaches to improve solvent productivity. Sporulation is a cell differentiation process triggered in bacteria in response to exposure to environmental stressors. The generated spores are metabolically inactive but resistant to harsh conditions (UV, chemicals, heat, oxygen). In Firmicutes, sporulation has been mainly studied in bacilli and pathogenic clostridia, and our knowledge of sporulation in solvent-producing or acetogenic clostridia is limited. Still, sporulation is an integral part of the cellular physiology of clostridia; thus, understanding the regulation of sporulation and its connection to solvent production may give clues to improve the performance of solventogenic clostridia. This review aims to provide an overview of the triggers, characteristics, and regulatory mechanism of sporulation in solventogenic clostridia. Those are further compared to the current knowledge on sporulation in the industrially relevant acetogenic clostridia. Finally, the potential applications of spores for process improvement are discussed.Key Points• The regulatory network governing sporulation initiation varies in solventogenic clostridia.• Media composition and cell density are the main triggers of sporulation.• Spores can be used to improve the fermentation process.

scholarly journals Achieving Viral Suppression in 90% of People Living With Human Immunodeficiency Virus on Antiretroviral Therapy in Low- and Middle-Income Countries: Progress, Challenges, and Opportunities

2018 ◽  
Vol 66 (10) ◽  
pp. 1487-1491 ◽  
Author(s):  
Jean B Nachega ◽  
Nadia A Sam-Agudu ◽  
Lynne M Mofenson ◽  
Mauro Schechter ◽  
John W Mellors
Keyword(s):  
Human Immunodeficiency Virus ◽  
Viral Suppression ◽  
Cost Effective ◽  
Term Treatment ◽  
Middle Income ◽  
Middle Income Countries ◽  
Long Term Treatment ◽  
Wide Range ◽  
Immunodeficiency Virus ◽  
Low And Middle Income

Abstract Although significant progress has been made, the latest data from low- and middle-income countries show substantial gaps in reaching the third “90%” (viral suppression) of the UNAIDS 90-90-90 goals, especially among vulnerable and key populations. This article discusses critical gaps and promising, evidence-based solutions. There is no simple and/or single approach to achieve the last 90%. This will require multifaceted, scalable strategies that engage people living with human immunodeficiency virus, motivate long-term treatment adherence, and are community-entrenched and ‑supported, cost-effective, and tailored to a wide range of global communities.

Sign in / Sign up

Export Citation Format

Share Document