Cytocompatibility of 3D printed dental materials for temporary restorations on fibroblasts

Abstract Background Three-dimensional (3D) printing is widely used in the fabrication of dental prostheses; however, the influence of dental materials used for 3D printing on temporary restoration of fibroblasts in tissues is unclear. Thus, the influence of different dental materials on fibroblasts were investigated. Methods Digital light processing (DLP) type 3D printing was used. Specimens in the control group were fabricated by mixing liquid and powder self-curing resin restoration materials. The temporary resin materials used were Model, Castable, Clear-SG, Tray, and Temporary, and the self-curing resin materials used were Lang dental, Alike, Milky blue, TOKVSO CUREFAST, and UniFast III. Fibroblast cells were cultured on each specimen and subsequently post-treated for analysis. Morphology of the adhered cells were observed using a confocal laser scanning microscope (CLSM) and a scanning electron microscope (SEM). Results CLSM and SEM cell imaging revealed that the 3D printed material group presented better cell adhesion with well-distributed filopodia compared to that in the conventional resin material group. Cell proliferation was significantly higher in the 3D printing materials. Conclusion Superior cytocompatibility of the specimens fabricated through 3D printing and polishing process was demonstrated with the proof of better cell adhesion and higher cell proliferation.

Download Full-text

Cytocompatibility of 3D printed dental materials for temporary restorations on fibroblasts

10.21203/rs.2.21028/v3 ◽

2020 ◽

Author(s):

Jung-Hyun Park ◽

Hyun Lee ◽

Jong-Woo Kim ◽

Ji-Hwan Kim

Keyword(s):

Cell Proliferation ◽

Cell Adhesion ◽

3D Printing ◽

Laser Scanning ◽

Dental Materials ◽

Confocal Laser ◽

Control Group ◽

Digital Light Processing ◽

3D Printed ◽

Materials Used

Download Full-text

Cytocompatibility of 3D printed dental materials for temporary restorations on fibroblasts

10.21203/rs.2.21028/v1 ◽

2020 ◽

Author(s):

Jung-Hyun Park ◽

Hyun Lee ◽

Jong-Woo Kim ◽

Ji-Hwan Kim

Keyword(s):

3D Printing ◽

Laser Scanning ◽

Dental Materials ◽

Three Dimensional ◽

Confocal Laser Scanning Microscope ◽

Confocal Laser ◽

Control Group ◽

Digital Light Processing ◽

3D Printed ◽

Materials Used

Abstract Background Three-dimensional (3D) printing is widely used in the fabrication of dental prostheses; however, the influence of dental materials used for 3D printing on temporary restoration of fibroblasts in tissues is unclear. Thus, the influence of different dental materials on fibroblasts were investigated. Methods Digital light processing (DLP) type 3D printing was used. Specimens in the control group were fabricated by mixing liquid and powder self-curing resin restoration materials. The temporary resin materials used were Model, Castable, Clear-SG, Tray, and Temporary, and the self-curing resin materials used were Lang dental, Alike, Milky blue, TOKVSO CUREFAST, and UniFast III. Fibroblast cells were cultured on each specimen and subsequently post-treated for analysis. Morphology of the adhered cells were observed using a confocal laser scanning microscope (CLSM) and a scanning electron microscope (SEM). Results CLSM and SEM cell imaging revealed that the 3D printed material group presented better cell adhesion with well-distributed filopodia compared to that in the conventional resin material group. Cell proliferation was significantly higher in the 3D printing materials. Conclusion This indicates that using resins fabricated by 3D printing technology rather than the ones fabricated by self-curing technology is recommended for the fabrication of dental temporary restorations.

Download Full-text

Fabrication and In Vitro Evaluation of 3D Printed Porous Polyetherimide Scaffolds for Bone Tissue Engineering

BioMed Research International ◽

10.1155/2019/2076138 ◽

2019 ◽

Vol 2019 ◽

pp. 1-8 ◽

Cited By ~ 1

Author(s):

Xiongfeng Tang ◽

Yanguo Qin ◽

Xinyu Xu ◽

Deming Guo ◽

Wenli Ye ◽

...

Keyword(s):

Mechanical Properties ◽

Tissue Engineering ◽

Cell Proliferation ◽

Cell Adhesion ◽

3D Printing ◽

Bone Tissue Engineering ◽

Bone Tissue ◽

Porous Scaffold ◽

3D Printed

For bone tissue engineering, the porous scaffold should provide a biocompatible environment for cell adhesion, proliferation, and differentiation and match the mechanical properties of native bone tissue. In this work, we fabricated porous polyetherimide (PEI) scaffolds using a three-dimensional (3D) printing system, and the pore size was set as 800 μm. The morphology of 3D PEI scaffolds was characterized by the scanning electron microscope. To investigate the mechanical properties of the 3D PEI scaffold, the compressive mechanical test was performed via an electronic universal testing system. For the in vitro cell experiment, bone marrow stromal cells (BMSCs) were cultured on the surface of the 3D PEI scaffold and PEI slice, and cytotoxicity, cell adhesion, and cell proliferation were detected to verify their biocompatibility. Besides, the alkaline phosphatase staining and Alizarin Red staining were performed on the BMSCs of different samples to evaluate the osteogenic differentiation. Through these studies, we found that the 3D PEI scaffold showed an interconnected porous structure, which was consistent with the design. The elastic modulus of the 3D PEI scaffold (941.33 ± 65.26 MPa) falls in the range of modulus for the native cancellous bone. Moreover, the cell proliferation and morphology on the 3D PEI scaffold were better than those on the PEI slice, which revealed that the porous scaffold has good biocompatibility and that no toxic substances were produced during the progress of high-temperature 3D printing. The osteogenic differentiation level of the 3D PEI scaffold and PEI slice was equal and ordinary. All of these results suggest the 3D printed PEI scaffold would be a potential strategy for bone tissue engineering.

Download Full-text

3D printing of metasurface-based dual-linear polarization converter

Flexible and Printed Electronics ◽

10.1088/2058-8585/ac3dff ◽

2021 ◽

Author(s):

Gyeongyeong Lee ◽

Yeong-Hoon Noh ◽

In-Gon Lee ◽

Ic-Pyo Hong ◽

Jong-Gwan Yook ◽

...

Keyword(s):

3D Printing ◽

Linear Polarization ◽

Orthogonal Polarization ◽

Polarization Conversion ◽

Polarization Converter ◽

Digital Light Processing ◽

Conductive Materials ◽

Complex Shapes ◽

3D Printed ◽

Materials Used

Abstract 3D printing using digital light processing (DLP) technology has been studied in various fields because of its ability to create complex shapes through a simple process. In this study, DLP 3D printing was employed in the implementation of the metasurface-based dual-linear polarization converter (DLPC). The unit cell of the metasurface-based DLPC for linear polarization conversion was designed consisting of the upper and lower dipole-pair antennas connected through vias and a shielding layer that electrically shields the antennas from each other, and its fabrication was based on the characterization results of the dielectric properties of the photocurable substrate materials and electrical properties of the conductive materials used for synthesizing the metasurface. The printability evaluation of dipole pairs, vias, and a shielding layer was carried out to implement the detailed structures of the DLPC in 3D printing. The electromagnetic wave transmission characteristics of the 3D-printed 8×8 array DLPC demonstrated an orthogonal polarization conversion, as predicted by the simulation results. This study confirmed that the DLP-based 3D printing technology can go beyond the existing functions of manufacturing objects and can be applied to the implementation of various electronics based on different meta-structures.

Download Full-text

Bone Regeneration Capability of 3D Printed Ceramic Scaffolds

International Journal of Molecular Sciences ◽

10.3390/ijms21144837 ◽

2020 ◽

Vol 21 (14) ◽

pp. 4837 ◽

Cited By ~ 4

Author(s):

Ju-Won Kim ◽

Byoung-Eun Yang ◽

Seok-Jin Hong ◽

Hyo-Geun Choi ◽

Sun-Ju Byeon ◽

...

Keyword(s):

3D Printing ◽

Bone Regeneration ◽

Negative Control Group ◽

Negative Control ◽

Control Group ◽

Digital Light Processing ◽

Defect Sites ◽

Significant Difference ◽

Printing System ◽

3D Printed

In this study, we evaluated the bone regenerative capability of a customizable hydroxyapatite (HA) and tricalcium phosphate (TCP) scaffold using a digital light processing (DLP)-type 3D printing system. Twelve healthy adult male beagle dogs were the study subjects. A total of 48 defects were created, with two defects on each side of the mandible in all the dogs. The defect sites in the negative control group (sixteen defects) were left untreated (the NS group), whereas those in the positive control group (sixteen defects) were filled with a particle-type substitute (the PS group). The defect sites in the experimental groups (sixteen defects) were filled with a 3D printed substitute (the 3DS group). Six dogs each were exterminated after healing periods of 4 and 8 weeks. Radiological and histomorphometrical evaluations were then performed. None of the groups showed any specific problems. In radiological evaluation, there was a significant difference in the amount of new bone formation after 4 weeks (p < 0.05) between the PS and 3DS groups. For both of the evaluations, the difference in the total amount of bone after 8 weeks was statistically significant (p < 0.05). There was no statistically significant difference in new bone between the PS and 3DS groups in both evaluations after 8 weeks (p > 0.05). The proposed HA/TCP scaffold without polymers, obtained using the DLP-type 3D printing system, can be applied for bone regeneration. The 3D printing of a HA/TCP scaffold without polymers can be used for fabricating customized bone grafting substitutes.

Download Full-text

Cell adhesion and proliferation on common 3D printing materials used in stereolithography of microfluidic devices

Lab on a Chip ◽

10.1039/d0lc00114g ◽

2020 ◽

Vol 20 (13) ◽

pp. 2372-2382 ◽

Cited By ~ 2

Author(s):

Kati Piironen ◽

Markus Haapala ◽

Virpi Talman ◽

Päivi Järvinen ◽

Tiina Sikanen

Keyword(s):

Cell Adhesion ◽

3D Printing ◽

Cell Survival ◽

Microfluidic Devices ◽

3D Printed ◽

Materials Used ◽

Cell Adhesion And Proliferation

This work reveals the material impacts on long-term cell survival and adhesion on 3D printed surfaces manufactured by stereolithography.

Download Full-text

Mechanical Properties and Biocompatibility of Urethane Acrylate-Based 3D-Printed Denture Base Resin

Polymers ◽

10.3390/polym13050822 ◽

2021 ◽

Vol 13 (5) ◽

pp. 822

Author(s):

Jy-Jiunn Tzeng ◽

Tzu-Sen Yang ◽

Wei-Fang Lee ◽

Hsuan Chen ◽

Hung-Ming Chang

Keyword(s):

Mechanical Properties ◽

3D Printing ◽

Flexural Modulus ◽

Measurement Data ◽

Uv Exposure ◽

Control Group ◽

Urethane Acrylate ◽

Shore Hardness ◽

Digital Light Processing ◽

Denture Base

In this study, five urethane acrylates (UAs), namely aliphatic urethane hexa-acrylate (87A), aromatic urethane hexa-acrylate (88A), aliphatic UA (588), aliphatic urethane triacrylate diluted in 15% HDD (594), and high-functional aliphatic UA (5812), were selected to formulate five UA-based photopolymer resins for digital light processing (DLP)-based 3D printing. Each UA (40 wt%) was added and blended homogenously with ethoxylated pentaerythritol tetraacrylate (40 wt%), isobornyl acrylate (12 wt%), diphenyl (2,4,6-trimethylbenzoyl) phosphine oxide (3 wt%), and a pink acrylic (5 wt%). Each UA-based resin specimen was designed using CAD software and fabricated using a DLP 3D printer to specific dimensions. Characteristics, mechanical properties, and cytotoxicity levels of these designed UA-based resins were investigated and compared with a commercial 3D printing denture base acrylic resin (BB base) control group at different UV exposure times. Shore hardness-measurement data and MTT assays were analyzed using a one-way analysis of variance with Bonferroni’s post hoc test, whereas viscosity, maximum strength, and modulus were analyzed using the Kruskal–Wallis test (α = 0.05). UA-based photopolymer resins with tunable mechanical properties were successfully prepared by replacing the UA materials and the UV exposure times. After 15 min of UV exposure, the 5812 and 594 groups exhibited higher viscosities, whereas the 88A and 87A groups exhibited lower viscosities compared with the BB base group. Maximum flexural strength, flexural modulus, and Shore hardness values also revealed significant differences among materials (p < 0.001). Based on MTT assay results, the UA-based photopolymer resins were nontoxic. In the present study, mechanical properties of the designed photopolymer resins could be adjusted by changing the UA or UV exposure time, suggesting that aliphatic urethane acrylate has good potential for use in the design of printable resins for DLP-type 3D printing in dental applications.

Download Full-text

DESIGN OF A 3D-PRINTED THREE-CLAW ROBOTIC GRIPPER END-EFFECTOR

ASEAN Engineering Journal ◽

10.11113/aej.v11.17865 ◽

2021 ◽

Vol 11 (4) ◽

pp. 70-79

Author(s):

Dino Dominic Forte Ligutan ◽

Argel Alejandro Bandala ◽

Jason Limon Española ◽

Richard Josiah Calayag Tan Ai ◽

Ryan Rhay Ponce Vicerra ◽

...

Keyword(s):

3D Printing ◽

Polylactic Acid ◽

Grip Force ◽

Thermoplastic Polyurethane ◽

Robotic Arm ◽

End Effector ◽

Design Considerations ◽

3D Printed ◽

Materials Used ◽

Metal Work

The development of a novel 3D-printed three-claw robotic gripper shall be described in this paper with the goal of incorporating various design considerations. Such considerations include the grip reliability and stability, grip force maximization, wide object grasping capability. Modularization of its components is another consideration that allows its parts to be easily machined and reusable. The design was realized by 3D printing using a combination of tough polylactic acid (PLA) material and thermoplastic polyurethane (TPU) material. In practice, additional tolerances were also considered for 3D printing of materials to compensate for possible expansion or shrinkage of the materials used to achieve the required functionality. The aim of the study is to explore the design and eventually deploy the three-claw robotic gripper to an actual robotic arm once its metal work fabrication is finished.

Download Full-text

Cost-Effectively 3D-Printed Rigid and Versatile Interpenetrating Polymer Networks

Materials ◽

10.3390/ma14164544 ◽

2021 ◽

Vol 14 (16) ◽

pp. 4544

Author(s):

Osman Konuray ◽

Arnau Sola ◽

Jordi Bonada ◽

Agnieszka Tercjak ◽

Albert Fabregat-Sanjuan ◽

...

Keyword(s):

3D Printing ◽

Polymer Networks ◽

Complex Form ◽

Interpenetrating Polymer Networks ◽

Dual Processing ◽

Digital Light Processing ◽

Superior Mechanical Properties ◽

3D Printed ◽

Acrylate Resin ◽

Printed Materials

Versatile acrylate–epoxy hybrid formulations are becoming widespread in photo/thermal dual-processing scenarios, especially in 3D printing applications. Usually, parts are printed in a stereolithography or digital light processing (DLP) 3D printer, after which a thermal treatment would bestow the final material with superior mechanical properties. We report the successful formulation of such a hybrid system, consisting of a commercial 3D printing acrylate resin modified by an epoxy–anhydride mixture. In the final polymeric network, we observed segregation of an epoxy-rich phase as nano-domains, similar to what was observed in a previous work. However, in the current work, we show the effectiveness of a coupling agent added to the formulation to mitigate this segregation for when such phase separation is undesired. The hybrid materials showed significant improvement of Young’s modulus over the neat acrylate. Once the flexible, partially-cured material was printed with a minimal number of layers, it could be molded into a complex form and thermally cured. Temporary shapes were readily programmable on this final material, with easy shape recovery under mild temperatures. Inspired by repairable 3D printed materials described recently, we manufactured a large object by printing its two halves, and then joined them covalently at the thermal cure stage with an apparently seamless union.

Download Full-text

3D Printing of Thermo-Sensitive Drugs

Pharmaceutics ◽

10.3390/pharmaceutics13091524 ◽

2021 ◽

Vol 13 (9) ◽

pp. 1524

Author(s):

Sadikalmahdi Abdella ◽

Souha H. Youssef ◽

Franklin Afinjuomo ◽

Yunmei Song ◽

Paris Fouladian ◽

...

Keyword(s):

3D Printing ◽

Three Dimensional ◽

Fused Deposition Modelling ◽

Future Directions ◽

Digital Light Processing ◽

Fused Deposition ◽

Printing Technique ◽

3D Printed ◽

Semi Solid ◽

Selection Of

Three-dimensional (3D) printing is among the rapidly evolving technologies with applications in many sectors. The pharmaceutical industry is no exception, and the approval of the first 3D-printed tablet (Spiratam®) marked a revolution in the field. Several studies reported the fabrication of different dosage forms using a range of 3D printing techniques. Thermosensitive drugs compose a considerable segment of available medications in the market requiring strict temperature control during processing to ensure their efficacy and safety. Heating involved in some of the 3D printing technologies raises concerns regarding the feasibility of the techniques for printing thermolabile drugs. Studies reported that semi-solid extrusion (SSE) is the commonly used printing technique to fabricate thermosensitive drugs. Digital light processing (DLP), binder jetting (BJ), and stereolithography (SLA) can also be used for the fabrication of thermosensitive drugs as they do not involve heating elements. Nonetheless, degradation of some drugs by light source used in the techniques was reported. Interestingly, fused deposition modelling (FDM) coupled with filling techniques offered protection against thermal degradation. Concepts such as selection of low melting point polymers, adjustment of printing parameters, and coupling of more than one printing technique were exploited in printing thermosensitive drugs. This systematic review presents challenges, 3DP procedures, and future directions of 3D printing of thermo-sensitive formulations.

Download Full-text