scholarly journals Enhancing Carbon Utilization and Adsorption Performance of Sludge Derived Activated Carbon through Molten Salt Synthesis Method

2021 ◽  
Author(s):  
En Shi ◽  
Xinyu Wang ◽  
Miao Zhang ◽  
Xin Wang ◽  
Jianchun Gao ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Molten Salt ◽  
Carbon Emissions ◽  
Chemical Activation ◽  
Total Carbon ◽  
Molten Salt Synthesis ◽  
Activation Process ◽  
Mass Ratio ◽  
Carbon Utilization ◽  
Carbon Mass

Abstract Sewage sludge is carbonaceous organic material and an inevitable by-product of biological wastewater treatment process. The traditional sludge disposal routes may cause serious pollution risks, e. g. large amounts of carbon emissions. Molten salt synthesis (MSS) method could complete the carbonization and activation two processes within a single-step, and the complexity of chemical activation process could be significantly reduced. In this work, sludge derived activated carbon (SDAC) was prepared by MSS method with ZnCl2 . The mass ratio of ZnCl2 to sludge had a significant effect on both the physicochemical properties and surface chemistry of SDAC. As the mass ratio of ZnCl2 to sludge was 1, the maximum specific surface area of SDAC was 549.72 m2/g. The maximum adsorbing capacity of methylene blue (MB) and CO2 were 0.0786 and 0.0575 mg/mg(SDAC), respectively. The highest yield and carbon utilization potential of SDAC were 517.87 mg(SDAC)/g(sludge) and 178.56 mg(carbon)/g(sludge), respectively. According to carbon mass balance, the total carbon mass in SDAC adsorbed MB and CO2 can be achieved to 203.00 and 186.68 mg(carbon)/g(sludge), respectively. It was suggested that MSS method can be used to reduce carbon emissions and improve carbon adsorption during SDAC preparation.

scholarly journals Computer Analysis of the Effect of Activation Temperature on the Microporous Structure Development of Activated Carbon Derived from Common Polypody

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 2951
Author(s):  
Mirosław Kwiatkowski ◽  
Jarosław Serafin ◽  
Andy M. Booth ◽  
Beata Michalkiewicz
Keyword(s):  
Activated Carbon ◽  
Porous Structure ◽  
Computer Analysis ◽  
Density Functional ◽  
Activated Carbons ◽  
Chemical Activation ◽  
Geometrical Parameters ◽  
Activation Process ◽  
Microporous Structure ◽  
Activation Temperature

This paper presents the results of a computer analysis of the effect of activation process temperature on the development of the microporous structure of activated carbon derived from the leaves of common polypody (Polypodium vulgare) via chemical activation with phosphoric acid (H3PO4) at activation temperatures of 700, 800, and 900 °C. An unconventional approach to porous structure analysis, using the new numerical clustering-based adsorption analysis (LBET) method together with the implemented unique gas state equation, was used in this study. The LBET method is based on unique mathematical models that take into account, in addition to surface heterogeneity, the possibility of molecule clusters branching and the geometric and energy limitations of adsorbate cluster formation. It enabled us to determine a set of parameters comprehensively and reliably describing the porous structure of carbon material on the basis of the determined adsorption isotherm. Porous structure analyses using the LBET method were based on nitrogen (N2), carbon dioxide (CO2), and methane (CH4) adsorption isotherms determined for individual activated carbon. The analyses carried out showed the highest CO2 adsorption capacity for activated carbon obtained was at an activation temperature of 900 °C, a value only slightly higher than that obtained for activated carbon prepared at 700 °C, but the values of geometrical parameters determined for these activated carbons showed significant differences. The results of the analyses obtained with the LBET method were also compared with the results of iodine number analysis and the results obtained with the Brunauer–Emmett–Teller (BET), Dubinin–Radushkevich (DR), and quenched solid density functional theory (QSDFT) methods, demonstrating their complementarity.

scholarly journals Synthesis and Characterisation of Pyridinium-Based Ionic Liquid as Activating Agent in Rubber Seed Shell Activated Carbon Production for CO2 Capture

2021 ◽  
Vol 82 (1) ◽  
pp. 85-95
Author(s):  
Nawwarah Mokti ◽  
Azry Borhan ◽  
Siti Nur Azella Zaine ◽  
Hayyiratul Fatimah Mohd Zaid
Keyword(s):  
Ionic Liquid ◽  
Activated Carbon ◽  
Adsorption Capacity ◽  
Co2 Capture ◽  
Low Cost ◽  
Chemical Activation ◽  
Green Technology ◽  
Activation Process ◽  
Rubber Seed ◽  
Activating Agent

The use of an activating agent in chemical activation of activated carbon (AC) production is very important as it will help to open the pore structure of AC as adsorbents and could enhance its performance for adsorption capacity. In this study, a pyridinium-based ionic liquid (IL), 1-butylpyridinium bis(trifluoromethylsulfonyl) imide, [C4Py][Tf2N] has been synthesized by using anion exchange reaction and was characterized using few analyses such as 1H-NMR, 13C-NMR and FTIR. Low-cost AC was synthesized by chemical activation process in which rubber seed shell (RSS) and ionic liquid [C4Py][Tf2N] were employed as the precursor and activating agent, respectively. AC has been prepared with different IL concentration (1% and 10%) at 500°C and 800°C for 2 hours. Sample AC2 shows the highest SBET and VT which are 392.8927 m2/g and 0.2059 cm3/g respectively. The surface morphology of synthesized AC can be clearly seen through FESEM analysis. A high concentration of IL in sample AC10 contributed to blockage of pores by the IL. On the other hand, the performance of synthesized AC for CO2 adsorption capacity also studied by using static volumetric technique at 1 bar and 25°C. Sample AC2 contributed the highest CO2 uptakes which is 50.783 cm3/g. This current work shows that the use of low concentration IL as an activating agent has the potential to produce porous AC, which offers low-cost, green technology as well as promising application towards CO2 capture.

scholarly journals Adsorption Property, Kinetic and Equilibrium Studies of Activated Carbon Fiber Prepared from Liquefied Wood by Zncl2 Activation

Materials ◽  
2019 ◽  
Vol 12 (9) ◽  
pp. 1377 ◽  
Author(s):  
Ruoke Ma ◽  
Xianxian Qin ◽  
Zhigao Liu ◽  
Yunlin Fu
Keyword(s):  
Activated Carbon ◽  
Carbon Fiber ◽  
Adsorption Property ◽  
Chemical Activation ◽  
Activated Carbon Fiber ◽  
Activation Process ◽  
Order Kinetic ◽  
Liquefied Wood ◽  
Zncl2 Activation ◽  
Mb Adsorption

Activated carbon fiber was prepared from liquefied wood by chemical activation with ZnCl2 (Z-LWACF) at different impregnation ratios, with a particular focus on its adsorption property, kinetic and isotherm. The characterization and properties of Z-LWACFs were investigated by nitrogen adsorption/desorption, X-ray photoelectron spectroscopy (XPS), methylene blue (MB) and iodine adsorption. Two activation process methods were employed to prepare Z-LWACF and contrasted with others fibers. The results showed that the Z-LWACF obtained by one-step ZnCl2 activation present higher yields and specific surface area than others fibers. Besides, the change of MB adsorption value at different impregnation ratios was consistent with pore structure distribution above 1.5 nm pore size, indicating that larger micropores (1.5 to 2 nm) and mesopores played a major role in the MB adsorption by Z-LWACF. The kinetics of MB adsorption process was found to follow the pseudo-second-order kinetic model and the adsorption rate was controlled by chemisorption. It was also found that MB adsroption by Z-LWACF belonged to monolayer adsorption and Z-LWACF was easy to adsorb MB.

Adsorptive Removal of Pb(II) Ion from Aqueous Solution Using Rice Husk-Based Activated Carbon

2014 ◽  
Vol 875-877 ◽  
pp. 196-201 ◽  
Author(s):  
Mohd Faisal Taha ◽  
Ahmad S. Rosman ◽  
Maizatul S. Shaharun
Keyword(s):  
Aqueous Solution ◽  
Activated Carbon ◽  
Rice Husk ◽  
Low Cost ◽  
Chemical Activation ◽  
Textural Properties ◽  
Activation Process ◽  
Adsorption Studies ◽  
Three Samples ◽  
Equilibrium Data

The potential of rice husk-based activated carbon as an alternative low-cost adsorbent for the removal of Pb (II) ion from aqueous solution was investigated. Rice husk-based activated carbon was preparedviachemical activation process using NaOH followed by the carbonization process at 500°C. Morphological analysis was conducted using field-emission scanning electron microscope /energy dispersive X-ray (FESEM/EDX) on three samples, i.e. raw rice husk, rice husk treated with NaOH and rice husk-based activated carbon. These three samples were also analyzed for their C, H, N, O and Si contents using CHN elemental analyzer and FESEM/EDX. The textural properties of rice husk-based activated carbon, i.e. surface area (253 m2/g) and pore volume (0.17 cm2/g), were determined by N2adsorption. The adsorption studies using rice husk-based activated carbon as an adsorbent to remove Pb (II) ion from aqueous solution were carried out at a fixed initial concentration of Pb (II) ion (150 ppm) with varying adsorbent dose as a function of contact time at room temperature. The concentration of Pb (II) ion was determined by atomic absorption spectrophotometer (AAS). The removal of Pb (II) ion from aqueous solution increased from 35 % to 82 % when the amount of rice husk-based activated carbon was increased from 0.05 g to 0.30 g. The equilibrium data obtained from adsorption studies was found to fit both Langmuir and Freundlich adsorption isotherms.

scholarly journals Preparation and Characterization of Activated Carbon from Waste Rubber Tires: A Comparison between Physical and Chemical Activation

2015 ◽  
Vol 1107 ◽  
pp. 347-352 ◽  
Author(s):  
Collin Glen Joseph ◽  
Duduku Krishniah ◽  
Yun Hin Taufiq-Yap ◽  
Masnah Massuanna ◽  
Jessica William
Keyword(s):  
Activated Carbon ◽  
Automobile Industry ◽  
Chemical Activation ◽  
Waste Product ◽  
Physical Activation ◽  
Activation Process ◽  
Waste Rubber ◽  
Percentage Yield ◽  
Static Conditions ◽  
Physical And Chemical

Abstract. Waste tires, which are an abundant waste product of the automobile industry, were used to prepare activated carbon by means of physical and chemical activation. A two-stage process was used, with a semi-carbonization stage as the first stage, followed by an activation stage as the second stage.All experiments were conducted in a laboratory-scale muffle furnace under static conditions in a self-generated atmosphere. During this process, the effects of the parametric variables of semi-carbonization time (for the physical activation process), activation time and temperature and impregnation ratios (for the chemical activation process) on the percentage yield were studied and compared. Varying these parametric variables yielded interesting results, which in turn affected the adsorption process of 2,4-DCP, which was the simulated pollutant in aqueous form. The optimized percentage yields of activated carbon that were obtained were 41.55% and 44.88% ofthe physical and chemical activation treatment processes respectively.Keywords: Physical activation, chemical activation, waste rubber tires, 2,4-dichlorophenol, activated carbon.

Preparation of Activated Carbon Monolith Electrodes from Sugarcane Bagasse by Physical and Physical-Chemical Activation Process for Supercapacitor Application

2014 ◽  
Vol 896 ◽  
pp. 179-182 ◽  
Author(s):  
Erman Taer ◽  
Iwantono ◽  
Saidul Tua Manik ◽  
R. Taslim ◽  
D. Dahlan ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Sugarcane Bagasse ◽  
Chemical Activation ◽  
Physical Activation ◽  
Activation Process ◽  
X Ray Diffraction ◽  
Supercapacitor Application ◽  
Carbon Monolith ◽  
Physical Chemical ◽  
Activated Carbon Monoliths

Binderless activated carbon monoliths (ACMs) for supercapacitor electrodes were prepared from sugarcane bagasse by two different methods of physical and combination of physical-chemical activation process. The CO2 gas was used as physical activation agent and 0.3 M KOH was chosen as chemical activation agent. The ACMs were tested as electrodes in two-electrode systems of the coin tape cell supercapacitor that consists of stainless steel as current collectors and 1 M H2SO4 as an electrolyte. The improving of resistive, capacitive and energy properties of combination of physical-chemical ACMs electrodes were shown by an impedance spectroscopy, a cyclic voltammetry and a galvanostatic charge-discharge method. The improving of resistive, capacitive and energy properties as high as 1 to 0.6 Ω, 146 to 178 F g-1, 3.83 to 4.72 W h kg-1, respectively. The X-ray diffraction analysis and field emission scanning electron microscope were performed to characterize the crystallite and morphology characteristics. The results showed that the combination of physical-chemical activation process have given a good improving in performance of the bagasse based ACMs electrodes in supercapacitor application.

scholarly journals Comparison of Surface and Structural Properties of Carbonaceous Materials Prepared by Chemical Activation of Tomato Paste Waste: The Effects of Activator Type and Impregnation Ratio

2016 ◽  
Vol 2016 ◽  
pp. 1-10 ◽  
Author(s):  
Nurgul Ozbay ◽  
Adife Seyda Yargic
Keyword(s):  
Activated Carbon ◽  
Activated Carbons ◽  
Low Cost ◽  
Chemical Activation ◽  
Nitrogen Adsorption ◽  
Xrd Analysis ◽  
Point Of Zero Charge ◽  
Activation Process ◽  
X Ray ◽  
Tomato Paste

Activated carbons were prepared by carbonization of tomato paste processing industry waste at 500°C followed by chemical activation with KOH, K2CO3, and HCl in N2 atmosphere at low temperature (500°C). The effects of different activating agents and impregnation ratios (25, 50, and 100 wt.%) on the materials’ characteristics were examined. Precursor, carbonized tomato waste (CTW), and activated carbons were characterized by using ultimate and proximate analysis, thermogravimetric analysis (TG/DTG), Fourier transform-infrared (FT-IR) spectroscopy, X-ray fluorescence (XRF) spectroscopy, point of zero charge measurements (pHPZC), particle size analyzer, scanning electron microscopy (SEM), energy dispersive X-ray (EDX) spectroscopy, nitrogen adsorption/desorption isotherms, and X-ray diffraction (XRD) analysis. Activation process improved pore formation and changed activated carbons’ surface characteristics. Activated carbon with the highest surface area (283 m3/g) was prepared by using 50 wt.% KOH as an activator. According to the experimental results, tomato paste waste could be used as an alternative precursor to produce low-cost activated carbon.

scholarly journals Karakteristik luas permukaan karbon aktif dari ampas tebu dengan aktivasi kimia

2018 ◽  
Vol 10 (3) ◽  
pp. 149
Author(s):  
Mahmud Sudibandriyo ◽  
L Lydia
Keyword(s):  
Activated Carbon ◽  
Surface Area ◽  
Sugarcane Bagasse ◽  
Chemical Activation ◽  
High Surface ◽  
High Surface Area ◽  
Physical Activation ◽  
Mass Ratio ◽  
Characterization Of Activated Carbon

Surface area characterization of activated carbon from sugarcane baggase by chemical activationAdsorption is one the process with many applications in the industries such as in a separation or in gas storage. In this adsorption, adsorbent selection is the most important thing. One of the adsorbent most suitable for this process is activated carbon. Previous studies show that high surface area of activated carbon can be produced from sugarcane bagasse using activator ZnCl2. The research’s goal is to produce activated carbon from sugarcane bagasse and determine the effects of activator on the surface area of activated carbon produced. Activators used in this research are KOH and ZnCl2 with the mass ratio of activator/carbon are 1/1, 2/1 and 3/1. The results show that The highest surface area, 938,2 m2/g, is obtained by activation using KOH with mass ratio of activator/carbon 3/1, whereas the highest surface area by activation using ZnCl2 is 632 m2/g with mass ratio of activator/carbon 2/1. For comparison, preparation of activated carbon by physical activation is also done and the surface area is 293 m2/g.Keywords: Activated carbon, chemical activation, sugarcane bagasse, KOH, ZnCl2 Abstrak Adsorpsi merupakan salah satu proses yang banyak digunakan dalam industri baik dalam pemisahan maupun untuk penyimpanan gas. Pada proses adsorpsi ini, pemilihan adsorben merupakan hal yang sangat penting. Salah satu jenis adsorben yang sangat cocok untuk proses ini adalah karbon aktif. Penelusuran studi sebelumnya menunjukkan bahwa karbon aktif dengan luas permukaan yang cukup tinggi dapat dibuat dari ampas tebu dengan menggunakan aktivator ZnCl2. Penelitian ini bertujuan untuk menghasilkan karbon aktif dari ampas tebu dengan aktivasi kimia serta mengetahui pengaruh aktivator terhadap luas permukaan karbon aktif yang dihasilkan. Aktivator yang digunakan dalam penelitian ini adalah KOH dan ZnCl2 dengan rasio massa aktivator/massa karbon 1/1, 2/1, dan 3/1. Aktivasi dilakukan pada temperatur 700 oC selama 1 jam. Hasil penelitian menunjukkan bahwa luas permukaan tertinggi sebesar 938,2 m2/g diperoleh dengan aktivasi menggunakan KOH dengan rasio massa aktivator/massa arang 3/1, sedangkan aktivasi dengan menggunakan ZnCl2 diperoleh luas permukaan tertinggi sebesar 632 m2/g dengan rasio massa aktivator/massa arang 2/1. Sebagai pembanding, pada penelitian ini juga dilakukan pembuatan karbon aktif dengan metode aktivasi fisika dan diperoleh luas permukaan karbon aktif sebesar 293 m2/g.Kata kunci: Aktivasi kimia, ampas tebu, karbon aktif, KOH, ZnCl2

scholarly journals Adsorption characteristics of activated carbon hollow fibers

2009 ◽  
Vol 15 (1) ◽  
pp. 29-31 ◽  
Author(s):  
Branka Kaludjerovic ◽  
Ljiljana Kljajevic ◽  
Danijela Sekulic ◽  
Jelena Stasic ◽  
Zarko Bogdanov
Keyword(s):  
Activated Carbon ◽  
Active Carbon ◽  
Carbon Material ◽  
Sodium Phosphate ◽  
Chemical Activation ◽  
Adsorption Properties ◽  
Hollow Fibers ◽  
Regenerated Cellulose ◽  
Activation Process ◽  
Sodium Phosphate Dibasic

Carbon hollow fibers were prepared with regenerated cellulose or polysulfone hollow fibers by chemical activation using sodium phosphate dibasic followed by the carbonization process. The activation process increases the adsorption properties of fibers which is more prominent for active carbone fibers obtained from the cellulose precursor. Chemical activation with sodium phosphate dibasic produces an active carbon material with both mesopores and micropores.

Sign in / Sign up

Export Citation Format

Share Document