scholarly journals Modeling And Simulation of The Advanced Structured Surfaces Machined By Specially Patterned Grinding Wheels Via The Structuring Grinding Process

2021 ◽  
Author(s):  
Amr Monier ◽  
Bing Guo ◽  
Qingliang Zhao ◽  
T.S. Mahmoud
Keyword(s):  
Working Conditions ◽  
Simulation Method ◽  
Grinding Wheel ◽  
Operating Parameters ◽  
Grinding Process ◽  
Grinding Wheels ◽  
Wheel Surface ◽  
Structured Surfaces ◽  
Structured Surface ◽  
Irregular Geometries

Abstract In this work, the ability to reshape the grinding wheels with special patterns to produce advanced structured surfaces with several geometries is studied. Firstly, a mathematical model is built for the process relating geometries of the grinding wheel, geometries of wheel patterns, the produced structured surface with the grinding operating parameters. Then, different regular and irregular geometries are designed to be patterned over the wheel surface. Afterward, a simulation method to express the patterned wheels and the structured surface at different working conditions is developed. The effects of the pattern geometries on the obtained structured surfaces are investigated.

The method of assessment of the grinding wheel cutting ability in the plunge grinding

2012 ◽  
Vol 2 (3) ◽  
Author(s):  
Krzysztof Nadolny
Keyword(s):  
Working Conditions ◽  
Comparative Assessment ◽  
Grinding Wheel ◽  
Grinding Process ◽  
Grinding Wheels ◽  
Plunge Grinding ◽  
Abrasive Grains ◽  
Ceramic Bond ◽  
Method Of Assessment ◽  
Grinding Kinematics

AbstractThis article presents the method of comparative assessment of the grinding wheel cutting ability in the plunge grinding kinematics. A new method has been developed to facilitate multicriterial assessment of the working conditions of the abrasive grains and the bond bridges, as well as the wear mechanisms of the GWAS, which occur during the grinding process, with simultaneous limitation of the workshop tests range. The work hereby describes the methodology of assessment of the grinding wheel cutting ability in a short grinding test that lasts for 3 seconds, for example, with a specially shaped grinding wheel, in plunge grinding. The grinding wheel macrogeometry modification applied in the developed method consists in forming a cone or a few zones of various diameters on its surface in the dressing cut. It presents an exemplary application of two variants of the method in the internal cylindrical plunge grinding, in 100Cr6 steel. Grinding wheels with microcrystalline corundum grains and ceramic bond underwent assessment. Analysis of the registered machining results showed greater efficacy of the method of cutting using a grinding wheel with zones of various diameters. The method allows for comparative tests upon different grinding wheels, with various grinding parameters and different machined materials.

scholarly journals Internal Cylindrical Grinding Process of INCONEL® Alloy 600 Using Grinding Wheels with Sol–Gel Alumina and a Synthetic Organosilicon Polymer-Based Impregnate

Micromachines ◽  
2020 ◽  
Vol 11 (2) ◽  
pp. 115 ◽  
Author(s):  
Wojciech Kapłonek ◽  
Krzysztof Nadolny ◽  
Krzysztof Rokosz ◽  
Jocelyne Marciano ◽  
Mozammel Mia ◽  
...  
Keyword(s):  
Sol Gel ◽  
Grinding Wheel ◽  
Grinding Process ◽  
Alloy 600 ◽  
Abrasive Tool ◽  
Grinding Wheels ◽  
Impregnation Process ◽  
Organosilicon Polymer ◽  
Internal Cylindrical Grinding ◽  
Abrasive Tools

The development of modern jet engines would not be possible without dynamically developed nickel–chromium-based superalloys, such as INCONEL® The effective abrasive machining of above materials brings with it many problems and challenges, such as intensive clogging of the grinding wheel active surface (GWAS). This extremely unfavorable effect causes a reduction in the cutting ability of the abrasive tool as well as increase to grinding forces and friction in the whole process. The authors of this work demonstrate that introduction of a synthetic organosilicon polymer-based impregnating substance to the GWAS can significantly improve the effects of carrying out the abrasive process of hard-to-cut materials. Experimental studies were carried out on a set of a silicon-treated small-sized sol–gel alumina 1-35×10×10-SG/F46G10VTO grinding wheels. The set contained abrasive tools after the internal cylindrical grinding process of INCONEL® alloy 600 rings and reference abrasive tools. The condition of the GWAS after the impregnation process was studied, including imaging and measurements of its microgeometry using confocal laser scanning microscopy (CLSM), microanalysis of its elemental distribution using energy dispersive X-ray fluorescence (EDXRF), and the influence of impregnation process on the grinding temperature using infrared thermography (IRT). The obtained results confirmed the correctness of introduction of the impregnating substance into the grinding wheel structure, and it was possible to obtain an abrasive tool with a recommended characteristic. The main favorable features of treated grinding wheel concerning the reduction of adhesion between the GWAS and grinding process products (limitation of the clogging phenomenon) as well as reduction of friction in the grinding process, which has a positive effect on the thermal conditions in the grinding zone.

Potential for improving efficiency of the internal cylindrical grinding process by modification of the grinding wheel structure—Part II: Grinding wheels made of superabrasive grains

2016 ◽  
Vol 231 (4) ◽  
pp. 813-823 ◽  
Author(s):  
Krzysztof Nadolny ◽  
Witold Habrat
Keyword(s):  
Cubic Boron Nitride ◽  
Positive Influence ◽  
Grinding Wheel ◽  
Grinding Process ◽  
Grinding Wheels ◽  
Structural Modifications ◽  
Synthetic Diamonds ◽  
Wide Range ◽  
Internal Cylindrical Grinding ◽  
Different Diameters

This article offers an overview of 11 grinding wheel construction modifications used in the peripheral grinding of flat, shaped, internal, and external cylindrical surfaces, when grinding wheels made of superabrasive grains are used (natural and synthetic diamonds, as well as mono- and microcrystalline cubic boron nitride). The text contains characteristics of grinding wheels with: bubble corundum grains, glass-crystalline bond, conic chamfer, zones of different diameters, a centrifugal provision of the coolant into the grinding zone, aggregate grains, zone-diversified structure, as well as impregnated (self-lubricating), multiporous, segment and “intelligent” grinding wheels. Each of the presented structural modifications were described by giving construction scheme, used abrasive grains, range of applications, advantages as well as disadvantages. Modifications of the grinding wheel construction allow for effective improvement of both the conditions and the results of the grinding process. A wide range of the known modifications allow for their proper selection depending on the required criteria of effective evaluation and taking into account the specific characteristics of superabrasive grains. As a result, it is possible to obtain positive influence on a number of technological factors of the grinding process. The described modifications of the grinding wheel structure can be also an inspiration and the basis for creating new solutions in this field.

Modeling of the Grinding Wheel Topography Depending on the Recipe-Dependent Volumetric Composition

2017 ◽  
Vol 140 (2) ◽  
Author(s):  
Sebastian Barth ◽  
Michael Rom ◽  
Christian Wrobel ◽  
Fritz Klocke
Keyword(s):  
Research Work ◽  
Distribution Functions ◽  
Grinding Wheel ◽  
Grinding Process ◽  
Grinding Wheels ◽  
Edge Zone ◽  
Application Behavior ◽  
Wheel Topography ◽  
Grinding Wheel Topography ◽  
Grinding Tool

The prediction of the grinding process result, such as the workpiece surface quality or the state of the edge zone depending on the used grinding wheel is still a great challenge for today's manufacturers and users of grinding tools. This is mainly caused by an inadequate predictability of force and temperature affecting the process. The force and the temperature strongly depend on the topography of the grinding wheel, which comes into contact with the workpiece during the grinding process. The topography of a grinding wheel mainly depends on the structure of the grinding wheel, which is determined by the recipe-dependent volumetric composition of the tool. So, the structure of a grinding tool determines its application behavior strongly. As result, the knowledge-based prediction of the grinding wheel topography and its influence on the machining behavior will only be possible if the recipe-dependent grinding wheel structure is known. This paper presents an innovative approach for modeling the grinding wheel structure and the resultant grinding wheel topography. The overall objective of the underlying research work was to create a mathematical-generic grinding tool model in which the spatial arrangement of the components, grains, bond, and pores, is simulated in a realistic manner starting from the recipe-dependent volumetric composition of a grinding wheel. This model enables the user to determine the resulting grinding wheel structure and the grinding wheel topography of vitrified and synthetic resin-bonded cubic boron nitride (CBN) grinding wheels depending on their specification and thus to predict their application behavior. The originality of the present research results is a generic approach for the modeling of grinding tools, which takes into account the entire grinding wheel structure to build up the topography. Therefore, original mathematical methods are used. The components of grinding wheels are analyzed, and distribution functions of the component's positions in the tools are determined. Thus, the statistical character of the grinding wheel structure is taken into account in the developed model. In future, the presented model opens new perspectives in order to optimize and to increase the productivity of grinding processes.

Optimization and Application of Laser-Dressed cBN Grinding Wheels

2016 ◽  
Vol 1136 ◽  
pp. 90-96 ◽  
Author(s):  
Ali Zahedi ◽  
Bahman Azarhoushang ◽  
Javad Akbari
Keyword(s):  
Environmental Concerns ◽  
Grinding Wheel ◽  
Grinding Process ◽  
Grinding Wheels ◽  
Average Roughness ◽  
Cylindrical Grinding ◽  
Laser Dressing ◽  
Dressing Tool ◽  
Cbn Grinding Wheel ◽  
Spindle Power

Laser-dressing has been shown to be a promising method for overcoming some shortcomings of the conventional methods such as high wear of the dressing tool and its environmental concerns, high induced damage to the grinding wheel, low form flexibility and low speed. In this study, a resin bonded cBN grinding wheel has been dressed with a picosecond Yb:YAG laser. The efficiency of the laser-dressed grinding wheels has been compared with the conventionally dressed and sharpened grinding wheels through execution of cylindrical grinding tests on a steel workpiece (100Cr6). The conventional dressing and sharpening processes have been performed by using a vitrified SiC wheel and vitrified alumina blocks, respectively. By recording the spindle power values along with the surface topography measurements of the ground workpieces and the extraction of two roughness parameters (the average roughness Ra and the average roughness depth Rz), it is possible to provide an assessment of the cylindrical grinding process with different dressing conditions i.e. laser-dressing and conventional dressing. Accordingly, a strategy will be proposed to optimize the cylindrical grinding process with laser-dressed wheels regarding the forces and roughness values.

Development on Micro Precision Truing Method of ELID-Grinding Wheel (2nd Report: Application to Edge Sharpening of Large Wheel)

2005 ◽  
Vol 291-292 ◽  
pp. 213-220 ◽  
Author(s):  
Shao Hui Yin ◽  
Wei Min Lin ◽  
Yoshihiro Uehara ◽  
Shinya MORITA ◽  
Hitoshi Ohmori ◽  
...  
Keyword(s):  
Surface Quality ◽  
Grinding Wheel ◽  
Grinding Process ◽  
Grinding Wheels ◽  
Elid Grinding ◽  
Diamond Grinding ◽  
Grinding Performance ◽  
Profile Accuracy ◽  
Large Wheel ◽  
Edge Sharpening

In V-groove ELID grinding process, to achieve optimal grinding performance and satisfactory surface quality and profile accuracy, metal bonded diamond grinding wheels need to be carefully sharpened. In this paper, we applied the proposed new micro-truing method consisting of electro-discharge truing and electrolysis-assisted mechanical truing to sharpen the edge of large grinding wheels. The minimum wheel tip radiuses of 6.3 and 8.5µm were achieved for the #4000 and #20000 grinding wheels. The truing mechanisms and sharpening performance are also discussed.

Detailed Analysis and Description of Grinding Wheel Topographies

2017 ◽  
Vol 139 (5) ◽  
Author(s):  
Markus Weiß ◽  
Fritz Klocke ◽  
Sebastian Barth ◽  
Matthias Rasim ◽  
Patrick Mattfeld
Keyword(s):  
Detailed Analysis ◽  
Functional Properties ◽  
Quantitative Description ◽  
Cutting Edge ◽  
Grinding Wheel ◽  
Grinding Process ◽  
Grinding Wheels ◽  
New Approach ◽  
Wheel Topography ◽  
The Impact

In this paper, an innovative approach for the description of the functional properties of a grinding wheel surface is discussed. First, the state of the art in the description of grinding wheel topographies is summarized. Furthermore, the fundamentals for a new approach for the quantitative description of grinding wheel topographies are provided. In order to analyze the functional properties of a grinding wheel's topography depending on its specification, grinding experiments were carried out. For the experimental investigations vitrified, synthetic resin bonded and electroplated grinding wheels with varied compositions were analyzed. During the experiments, the topographies of the investigated grinding wheels have been analyzed by means of the topotool in detail. The developed software tool allows a detailed description of the kinematic cutting edges depending on the grinding process parameters and the grinding wheel specification. In addition to the calculation of the number of kinematic cutting edges and the area per cutting edge, a differentiation of the cutting edge areas in normal and tangential areas of the grinding wheel's circumferential direction is implemented. Furthermore, the topotool enables to analyze the kinematic cutting edges shape by calculating the angles of the grain in different directions. This enables a detailed analysis and a quantitative comparison of grinding wheel topographies related to different grinding wheel specifications. In addition, the influence of the dressing process and wear conditions to the grinding wheel topography can be evaluated. The new approach allows a better characterization of the contact conditions between grinding wheel and workpiece. Hence, the impact of a specific topography on the grinding process behavior, the generated grinding energy distribution, and the grinding result can be revealed.

scholarly journals Evaluation of the Relationship Among Dressing Conditions Using Prismatic Dresser, Dressing Resistance, and Grinding Characteristics

2022 ◽  
Vol 16 (1) ◽  
pp. 12-20
Author(s):  
Gen Uchida ◽  
Takazo Yamada ◽  
Kouichi Ichihara ◽  
Makoto Harada ◽  
Tatsuya Kohara ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Surface Condition ◽  
Ground Surface ◽  
Grinding Wheel ◽  
Grinding Process ◽  
Practical Application ◽  
Wheel Surface ◽  
The Difference ◽  
Ground Surface Roughness ◽  
The Relationship

In the grinding process, the grinding wheel surface condition changes depending on the dressing conditions, which affects the ground surface roughness and grinding resistance. Several studies have been reported on the practical application of dressing using prismatic dressers in recent years. However, only a few studies that quantitatively evaluate the effects of differences in dressing conditions using prismatic dresser on the ground surface roughness and grinding resistance have been reported. Thus, this study aims to evaluate quantitatively the effect of the difference in dressing conditions using the prismatic dresser on the ground surface roughness and grinding resistance by focusing on the dressing resistance. In the experiment, dressing is performed by changing the dressing lead and the depth of dressing cut with a prismatic dresser, and the ground surface roughness and grinding resistance are measured. Consequently, by increasing the dressing lead and the depth of dressing cut, the ground surface roughness increased, and the grinding resistance decreased. This phenomenon was caused by the increase in dressing resistance when the dressing lead and the depth of dressing cut were increased, which caused a change in the grinding wheel surface condition. Furthermore, the influence of the difference in dressing conditions using the prismatic dresser on the ground surface roughness and grinding resistance can be quantitatively evaluated by using the dressing resistance.

Development on Micro Precision Truing Method of ELID-Grinding Wheel (1st Report: Principle & Fundamental Experiments)

2005 ◽  
Vol 291-292 ◽  
pp. 207-212 ◽  
Author(s):  
Hitoshi Ohmori ◽  
Shao Hui Yin ◽  
Wei Min Lin ◽  
Yoshihiro Uehara ◽  
Shinya MORITA ◽  
...  
Keyword(s):  
High Precision ◽  
High Efficiency ◽  
High Hardness ◽  
Experimental Results ◽  
Grinding Wheel ◽  
Grinding Process ◽  
Grinding Wheels ◽  
Elid Grinding ◽  
High Toughness ◽  
Diamond Grinding

Metal bonded diamond grinding wheels are widely used in the grinding process, especial in ELID grinding. However, truing is difficult owing to the high toughness of metal bond materials and high hardness of diamond abrasives. To realize high precision and high-efficiency truing, we propose a new micro-truing method consisting of electro-discharge truing and electrolysis-assisted mechanical truing in this paper. The process principle and fundamental experimental results are introduced, and the truing performance is discussed. Research results show that the proposed new method is effective for truing metal bonded diamond grinding wheels.

Reducing Wear of Abrasive Wheels Grinding Aerospace Alloys by Laser Assisted Cleaning

2005 ◽  
Author(s):  
Mark J. Jackson ◽  
Xun Chen
Keyword(s):  
Laser Power ◽  
Laser Cleaning ◽  
Grinding Wheel ◽  
Cleaning Process ◽  
Grinding Wheels ◽  
Wheel Surface ◽  
Power Flux ◽  
Aerospace Alloys ◽  
High Laser ◽  
Selection Of

A new method for cleaning loaded grinding wheels is introduced by applying a CO2 laser pulse to the wheel surface. It is shown that effective cleaning can be achieved by the selection of adequate laser power flux and irradiation duration. Fusion and evaporation of clogged chips play an important role in the laser cleaning process and subsequent wear of the grinding wheel. It is suggested that high laser power irradiance of short duration is essential for effective wheel cleaning and reduced wear of the grinding wheel with specially developed bonds.

Sign in / Sign up

Export Citation Format

Share Document