scholarly journals Enhanced cadmium removal from water by hydroxyapatite subjected to different thermal treatments

2020 ◽  
Vol 69 (7) ◽  
pp. 678-693
Author(s):  
R. Aouay ◽  
S. Jebri ◽  
A. Rebelo ◽  
J. M. F. Ferreira ◽  
I. Khattech
Keyword(s):  
Electron Microscopy ◽  
Sorption Process ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Cadmium Removal ◽  
Sorption Behaviour ◽  
Adsorption Mechanisms ◽  
Transmission Electron ◽  
Order Kinetic Model ◽  
Pseudo Second Order

Abstract Hydroxyapatite powders were synthesized according to a wet precipitation route and then subjected to heat treatments within the temperature range of 200–800 °C. The prepared samples were tested as sorbents for cadmium in an aqueous medium. The best performances were obtained with the material treated at 200 °C (HAp200), as the relevant sorbent textural features (SBET – specific surface area and Vp – total volume of pores) were least affected at this low calcination temperature. The maximum adsorption capacity at standard ambient temperature and pressure was 216.6 mg g−1, which increased to 240.7 mg g−1 by increasing the temperature from 25 to 40 °C, suggesting an endothermic nature of the adsorption process. Moreover, these data indicated that a thermal treatment at 200 °C enhanced the ability of the material in Cd2+ uptake by more than 100% compared to other similar studies. The adsorption kinetic process was better described by the pseudo-second-order kinetic model. Langmuir, Freundlich, and Dubinin–Kaganer–Radushkevich isotherms were applied to describe the sorption behaviour of Cd2+ ions onto the best adsorbent. Furthermore, a thermodynamic study was also performed to determine ΔH°, ΔS°, and ΔG° of the sorption process of this adsorbent. The adsorption mechanisms were investigated by Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy-transmission electron microscopy (SEM-TEM) observations.

Alkaline deoxygenated graphene oxide as adsorbent for cadmium ions removal from aqueous solutions

2015 ◽  
Vol 71 (11) ◽  
pp. 1611-1619 ◽  
Author(s):  
Jun Liu ◽  
Hongyan Du ◽  
Shaowei Yuan ◽  
Wanxia He ◽  
Pengju Yan ◽  
...  
Keyword(s):  
Graphene Oxide ◽  
Aqueous Solutions ◽  
Batch Adsorption ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Transmission Electron ◽  
Equilibrium Data ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Ft Ir

Alkaline deoxygenated graphene oxide (aGO) was prepared through alkaline hydrothermal treatment and used as adsorbent to remove Cd(II) ions from aqueous solutions for the first time. The characterization results of transmission electron microscopy, X-ray diffraction, Raman spectroscopy, and Fourier transform infrared (FT-IR) spectra indicate that aGO was successfully synthesized. The batch adsorption experiments showed that the adsorption kinetics could be described by the pseudo-second-order kinetic model, and the isotherms equilibrium data were well fitted with the Langmuir model. The maximum adsorption capacity of Cd(II) on aGO was 156 mg/g at pH 5 and T = 293 K. The adsorption thermodynamic parameters indicated that the adsorption process was a spontaneous and endothermic reaction. The mainly adsorption mechanism speculated from FT-IR results may be attributed to the electrostatic attraction between Cd2+ and negatively charged groups (–CO−) of aGO and cation-π interaction between Cd2+ and the graphene planes. The findings of this study demonstrate the potential utility of the nanomaterial aGO as an effective adsorbent for Cd(II) removal from aqueous solutions.

scholarly journals Gum Arabic-Magnetite Nanocomposite as an Eco-Friendly Adsorbent for Removal of Lead(II) Ions from Aqueous Solutions: Equilibrium, Kinetic and Thermodynamic Studies

Separations ◽  
2021 ◽  
Vol 8 (11) ◽  
pp. 224
Author(s):  
Ismat H. Ali ◽  
Mutasem Z. Bani-Fwaz ◽  
Adel A. El-Zahhar ◽  
Riadh Marzouki ◽  
Mosbah Jemmali ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Aqueous Solutions ◽  
Contact Time ◽  
Gum Arabic ◽  
Ion Concentration ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Transmission Electron ◽  
Order Kinetic Model ◽  
Langmuir Isotherm Model

In this study, a gum Arabic-magnetite nanocomposite (GA/MNPs) was synthesized using the solution method. The prepared nanocomposite was characterized by Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), vibrating sample magnetometer (VSM), and thermogravimetric analysis (TGA). The prepared composite was evaluated for the adsorption of lead(II) ions from aqueous solutions. The controlling factors such as pH, contact time, adsorbent dose, initial ion concentration, and temperature were investigated. The optimum adsorption conditions were found to be 0.3 g/50 mL, pH = 6.00, and contact time of 30 min. The experimental data well fitted the pseudo-second-order kinetic model and the Langmuir isotherm model. The maximum adsorption capacity was determined as 50.5 mg/g. Thermodynamic parameters were calculated postulating an endothermic and spontaneous process and a physio-sorption pathway.

scholarly journals Tetracycline adsorption on magnetic sludge biochar: size effect of the Fe 3 O 4 nanoparticles

2022 ◽  
Vol 9 (1) ◽  
Author(s):  
Suxing Luo ◽  
Jun Qin ◽  
Yuanhui Wu ◽  
Feng Feng
Keyword(s):  
Zeta Potential ◽  
Activated Sludge ◽  
Photoelectron Spectroscopy ◽  
Wastewater Treatment Plants ◽  
Sorption Process ◽  
Order Kinetic ◽  
X Ray ◽  
Transmission Electron ◽  
Order Kinetic Model ◽  
Pseudo Second Order

Activated sludge, which is difficult and expensive to treat and dispose of, is a key concern in wastewater treatment plants. In this study, magnetic sludge biochar containing activated sludge and different sizes (14.3, 40.2 and 90.5 nm) of Fe 3 O 4 nanoparticles was investigated as an effective adsorbent for tetracycline (TC) adsorption. Magnetic sludge-based biochar was prepared by a facile cross-linking method and characterized by transmission electron microscopy, Fourier transform infrared spectroscopy (FTIR), X-ray diffraction, X-ray photoelectron spectroscopy (XPS) and zeta potential analysis. The adsorption performances of TC on three kinds of adsorbents were investigated. Although 14.3 nm Fe 3 O 4 nanoparticles could be inclined to aggregate and partially filled with pores of biochar, it turned out that magnetic sludge biochar with 14.3 nm Fe 3 O 4 nanoparticles exhibited optimum performance for TC removal with adsorption capacity up to 184.5 mg g −1 , due to the larger amounts of functional groups and the change of zeta potential. Furthermore, the adsorption kinetics of TC on three kinds of adsorbents were studied, which implied that the pseudo-second-order kinetic model exhibited the better fit for the entire sorption process.

scholarly journals In Situ Synthesis of MIL-100(Fe) at the Surface of Fe3O4@AC as Highly Efficient Dye Adsorbing Nanocomposite

2019 ◽  
Vol 20 (22) ◽  
pp. 5612 ◽  
Author(s):  
Asma Hamedi ◽  
Francesco Trotta ◽  
Mahmood Borhani Zarandi ◽  
Marco Zanetti ◽  
Fabrizio Caldera ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Surface Area ◽  
Activated Charcoal ◽  
Order Kinetic ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
Order Kinetic Model ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Kinetics And Isotherms

A new magnetic nanocomposite called MIL-100(Fe) @Fe3O4@AC was synthesized by the hydrothermal method as a stable adsorbent for the removal of Rhodamine B (RhB) dye from aqueous medium. In this work, in order to increase the carbon uptake capacity, magnetic carbon was first synthesized and then the Fe3O4 was used as the iron (III) supplier to synthesize MIL-100(Fe). The size of these nanocomposite is about 30–50 nm. Compared with activated charcoal (AC) and magnetic activated charcoal (Fe3O4@AC) nanoparticles, the surface area of MIL-100(Fe) @Fe3O4@AC were eminently increased while the magnetic property of this adsorbent was decreased. The surface area of AC, Fe3O4@AC, and MIL-100(Fe) @Fe3O4@AC was 121, 351, and 620 m2/g, respectively. The magnetic and thermal property, chemical structure, and morphology of the MIL-100(Fe) @Fe3O4@AC were considered by vibrating sample magnetometer (VSM), thermogravimetric analysis (TGA), zeta potential, X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), Brunner-Emmet-Teller (BET), and transmission electron microscopy (TEM) analyses. The relatively high adsorption capacity was obtained at about 769.23 mg/g compared to other adsorbents to eliminate RhB dye from the aqueous solution within 40 min. Studies of adsorption kinetics and isotherms showed that RhB adsorption conformed the Langmuir isotherm model and the pseudo second-order kinetic model. Thermodynamic amounts depicted that the RhB adsorption was spontaneous and exothermic process. In addition, the obtained nanocomposite exhibited good reusability after several cycles. All experimental results showed that MIL-100(Fe) @Fe3O4@AC could be a prospective sorbent for the treatment of dye wastewater.

scholarly journals Fabrication of the magnetic mesoporous silica Fe-MCM-41-A as efficient adsorbent: performance, kinetics and mechanism

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Yige Guo ◽  
Bin Chen ◽  
Ying Zhao ◽  
Tianxue Yang
Keyword(s):  
Mesoporous Silica ◽  
Zero Valent Iron ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Environment And Health ◽  
Transmission Electron ◽  
Order Kinetic Model ◽  
Neutral Conditions ◽  
Magnetic Mesoporous Silica ◽  
Mcm 41

AbstractAntibiotics are emerging pollutants and increasingly present in aquaculture and industrial wastewater. Due to their impact on the environment and health, their removal has recently become a significant concern. In this investigation, we synthesized nano zero-valent iron-loaded magnetic mesoporous silica (Fe-MCM-41-A) via precipitation and applied the adsorption of oxytetracycline (OTC) from an aqueous solution. The effects of competing ions such as Na+, Ca2+ and Cu2+ on the adsorption process under different pH conditions were studied in depth to providing a theoretical basis for the application of nanomaterials. The characterization of the obtained material through transmission electron microscopy demonstrates that the adsorbent possesses hexagonal channels, which facilitate mass transfer during adsorption. The loaded zero-valent iron made the magnetic, and was thus separated under an applied magnetic field. The adsorption of OTC onto Fe-MCM-41-A is rapid and obeys the pseudo-second-order kinetic model, and the maximum adsorption capacity of OTC is 625.90 mg g−1. The reaction between OTC and Fe-MCM-41-A was inner complexation and was less affected by the Na+. The effect of Ca2+ on the adsorption was small under acidic and neutral conditions. However, the promotion effect of Ca2+ increased by the increase of pH. Cu2+ decreased the removal efficiencies continuously and the inhibitory effects decrease varied with the increase of pH. We propose that surface complexing, ion-exchange, cationic π-bonding, hydrogen bonding, and hydrophobicity are responsible for the adsorption of OTC onto Fe-MCM-41-A.

scholarly journals Insights into Starch Coated Nanozero Valent Iron-Graphene Composite for Cr(VI) Removal from Aqueous Medium

2016 ◽  
Vol 2016 ◽  
pp. 1-10 ◽  
Author(s):  
Prasanna Kumarathilaka ◽  
Vimukthi Jayaweera ◽  
Hasintha Wijesekara ◽  
I. R. M. Kottegoda ◽  
S. R. D. Rosa ◽  
...  
Keyword(s):  
Point Of Zero Charge ◽  
Inert Material ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
X Ray Diffraction ◽  
Graphene Composite ◽  
Removal Capacity ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
First Time

Embedding nanoparticles into an inert material like graphene is a viable option since hybrid materials are more capable than those based on pure nanoparticulates for the removal of toxic pollutants. This study reports for the first time on Cr(VI) removal capacity of novel starch stabilized nanozero valent iron-graphene composite (NZVI-Gn) under different pHs, contact time, and initial concentrations. Starch coated NZVI-Gn composite was developed through borohydrate reduction method. The structure and surface of the composite were characterized by scanning electron microscopy (SEM), X-ray diffraction spectroscopy (XRD), Fourier transform infrared spectroscopy (FTIR), Brunauer-Emmett-Teller (BET), and point of zero charge (pHpzc). The surface area and pHpzc of NZVI-Gn composite were reported as 525 m2 g−1 and 8.5, respectively. Highest Cr(VI) removal was achieved at pH 3, whereas 67.3% was removed within first few minutes and reached its equilibrium within 20 min obeying pseudo-second-order kinetic model, suggesting chemisorption as the rate limiting process. The partitioning of Cr(VI) at equilibrium is perfectly matched with Langmuir isotherm and maximum adsorption capacity of the NZVI-Gn composite is 143.28 mg g−1. Overall, these findings indicated that NZVI-Gn composite could be utilized as an efficient and magnetically separable adsorbent for removal of Cr(VI).

scholarly journals Adsorption of Reactive Black M-2R on Different Deacetylation Degree Chitosan

2011 ◽  
Vol 6 (3) ◽  
pp. 155892501100600 ◽  
Author(s):  
Fang Li ◽  
Chunmei Ding
Keyword(s):  
Sorption Process ◽  
Order Kinetic ◽  
Sorption Data ◽  
Kinetic Experiment ◽  
Isotherm Equation ◽  
Degree Of Deacetylation ◽  
Deacetylation Degree ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Effects Of Temperature

Different degree of deacetylation (DD) chitosan was prepared and used for the removal of a Reactive black M-2R (RBM) from aqueous solution. The effects of temperature (298 K~323 K), chitosan dosage, degree of deacetylation on RBM removal were investigated. The adsorption equilibrium was reached within one hour. In order to determine the adsorption capacity, the sorption data were analyzed by using linear form of Langmuir, Freundlich and Tempkin isotherm equation. Langmuir equation shows higher conformity than the other two equations. From the kinetic experiment data, it was found that the sorption process follows the pseudo-second-order kinetic model. Activation energy value for sorption process was found to be 58.28 kJ mol-1. Chitosan with 66% deacetylation degree (DD) exhibited good adsorption performance for RBM. In order to determine the interactions between RBM and chitosan, FTIR analysis was also conducted.

scholarly journals Karekterisasi, Kinetika, dan Isoterm Adsorpsi Limbah Ampas Kelapa sebagai Adsorben Ion Cu(II)

SAINTIFIK ◽  
2020 ◽  
Vol 6 (2) ◽  
pp. 104-115
Author(s):  
Agusriyadin Agusriyadin
Keyword(s):  
Adsorption Capacity ◽  
Ph Effect ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Optimum Conditions ◽  
Langmuir Adsorption ◽  
Adsorbent Surface ◽  
Adsorption Data ◽  
Order Kinetic Model ◽  
Pseudo Second Order

Penelitian ini bertujuan untuk menguji kemampuan AK dan AKPM dalam mengadsorpsi ion Cu (II), pengaruh parameter adsorpsi dan mekanisme adsorpsi. AK dan AKP Madsorben dibuat dari residu ampas kelapa. Adsorben dikarakterisasi dengan FTIR, SEM dan EDS. Pengaruh parameter adsorpsi seperti pH awal, dosis adsorben, waktu kontak dan konsentrasi ion Cu (II) awal diperiksa untuk menentukan kondisi optimum serapan tembaga (II). Ion Cu (II) yang teradsorpsi diukur berdasarkan pada konsentrasi Ion Cu (II) sebelum dan sesudah adsorpsi menggunakan metode AAS. Hasil karakterisasi menunjukkan bahwa struktur pori dan gugus fungsi tersedia pada permukaan adsorben. Menurut percobaan efek pH, kapasitas adsorpsi maksimum dicapai pada pH 7. Waktu kontak optimal dan konsentrasi tembaga awal (II) ditemukan masing-masing pada 120 menit dan 100 mg L-1. Data eksperimental sesuai dengan model kinetik orde dua orde dua, dan Langmuir isoterm adsorpsi yang diperoleh paling sesuai dengan data adsorpsi. Kapasitas adsorpsi maksimum adsorben ditemukan menjadi 4,73 dan 6,46 mg g-1 pada kondisi optimal. The results of characterization showed that the pore structure and the functional groups were available on adsorbent surface. According to the pH effect experiments, the maximum adsorption capacity was achieved at pH 7. Optimum contact time and initial copper(II) concentration were found at 120 min and 100 mg L-1, respectively. The experimental data were comply with the pseudo-second-order kinetic model, and Langmuir adsorption isotherm obtained best fitted the adsorption data. The maximum adsorption capacity of the adsorbents was found to be 4.73 and 6.46 mg g-1 at optimum conditions.

scholarly journals Preparation of chitosan/amine modified diatomite composites and adsorption properties of Hg(II) ions

2018 ◽  
Vol 77 (5) ◽  
pp. 1363-1371 ◽  
Author(s):  
Yong Fu ◽  
Yue Huang ◽  
Jianshe Hu ◽  
Zhengjie Zhang
Keyword(s):  
Schiff Base ◽  
Contact Time ◽  
Ph Value ◽  
Adsorption Properties ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Adsorption Effect ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Modified Diatomite

Abstract A green functional adsorbent (CAD) was prepared by Schiff base reaction of chitosan and amino-modified diatomite. The morphology, structure and adsorption properties of the CAD were characterized by Fourier transform infrared spectroscopy, thermogravimetric analysis, scanning electron microscopy and Brunauer Emmett Teller measurements. The effect of pH value, contact time and temperature on the adsorption of Hg(II) ions for the CAD is discussed in detail. The experimental results showed that the CAD had a large specific surface area and multifunctional groups such as amino, hydroxyl and Schiff base. The optimum adsorption effect was obtained when the pH value, temperature and contact time were 4, 25 °C and 120 min, respectively, and the corresponding maximum adsorption capacity of Hg(II) ions reached 102 mg/g. Moreover, the adsorption behavior of Hg(II) ions for the CAD followed the pseudo-second-order kinetic model and Langmuir model. The negative ΔG0 and ΔH0 suggested that the adsorption was a spontaneous exothermic process.

scholarly journals Preparation of Activated Biochar-Supported Magnetite Composite for Adsorption of Polychlorinated Phenols from Aqueous Solutions

Water ◽  
2019 ◽  
Vol 11 (9) ◽  
pp. 1899 ◽  
Author(s):  
Jun ◽  
Kim ◽  
Han ◽  
Yoon ◽  
Kim ◽  
...  
Keyword(s):  
Organic Pollutants ◽  
Hydrophobic Interactions ◽  
Order Kinetic ◽  
Adsorption Selectivity ◽  
Adsorption Mechanisms ◽  
Activated Biochar ◽  
Experimental Parameters ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Cetrimonium Bromide

For this study, we applied activated biochar (AB) and its composition with magnetite (AB-Fe3O4) as adsorbents for the removal of polychlorophenols in model wastewater. We comprehensively characterized these adsorbents and performed adsorption tests under several experimental parameters. Using FTIR, we confirmed successful synthesis of AB-Fe3O4 composite through cetrimonium bromide surfactant. We conducted adsorption tests using AB and AB-Fe3O4 to treat model wastewater containing polychlorophenols, such as 2,3,4,6-Tetrachlorophenol (TeCP), 2,4,6-Trichlorophenol (TCP), and 2,4-Dichlorophenol (DCP). Results of the isotherm and the kinetic experiments were well adapted to Freundlich’s isotherm model and the pseudo-second-order kinetic model, respectively. Main adsorption mechanisms in this study were attributed to non-covalent, π-electron acceptor–donor interactions and hydrophobic interactions judging from the number of chloride elements in each chlorophenol and its hydrophobic characteristics. We also considered the electrostatic repulsion effect between TeCP and AB, because adsorption performance of TeCP at basic condition was slightly worse than at weak acidic condition. Lastly, AB-Fe3O4 showed high adsorption selectivity of TeCP compared to other persistent organic pollutants (i.e., bisphenol A and sulfamethoxazole) due to hydrophobic interactions. We concluded that AB-Fe3O4 may be used as novel adsorbent for wastewater treatment including toxic and hydrophobic organic pollutants (e.g., TeCP).

Sign in / Sign up

Export Citation Format

Share Document