scholarly journals Mapping the summer 2017 surface water circulation of Picton Bay, ON

2018 ◽  
Vol 54 (2) ◽  
pp. 115-126
Author(s):  
J. A. Shore ◽  
P. Snell

Abstract On March 24, 2017, a fuel spill from a partially submerged barge in Picton Bay contaminated the source water for the drinking water supply of the local township. Immediately after the spill, management decisions regarding the water intake plant operations were made based on contaminant observations and projected wind conditions. From a management perspective, it is essential to understand all the dynamical forcing for a system to direct the best decision-making but, unfortunately, there are no historical observations of currents in Picton Bay or any in-depth numerical modelling studies that have established the circulation patterns or hydrodynamics of the bay. This paper presents observations of surface speeds and drifter pathways collected using Lagrangian drifters and compares the observations to the velocity field estimates from a wind forced three-dimensional hydrodynamic model. Surface drifters were deployed from July to September and moved southwest into the bay during each deployment with almost no tendency to turn and drift out of the bay. Model simulations indicated that currents in the bay are sensitive to small-scale local winds and that a boundary current exists that connects the spill site to the area of the water intake pipes in wind conditions that are to the southwest or southeast.

2014 ◽  
Vol 1079-1080 ◽  
pp. 584-588 ◽  
Author(s):  
Po Jen Lien ◽  
Hsiao Jung Ho ◽  
Tzu Hsin Lee ◽  
Wen Liang Lai ◽  
Chih Ming Kao

In subsurface environment, small-scale heterogeneities usually cause the reduction of the applicability of in situ remedial techniques. Biogeochemical heterogeneities and preferential groundwater flow paths create complex hydrogeologic conditions at most contaminated sites. A thorough understanding of the resulting three-dimensional distribution of contaminants is a necessity prior to determining a need for remediation. In this study, a gasoline spill site was selected to examine the effects of aquifer heterogeneities and geochemical variations on petroleum hydrocarbon biodegradation via different oxidation-reduction process. At this site, two multilevel sampling wells were installed to delineate the lateral (5 m) and vertical (0.5 m) distribution of contaminant concentrations and different biogeochemical parameters. Two 5-cm (I.D.) continuous soil cores [from 4 to 8 m below land surface (bls)] were collected within the gasoline plume to evaluate the distribution of the microbial population in soils. Results show that high microbial activities were observed in soil samples based on the following evidences: (1) high petroleum hydrocarbon degradation rate, and (2) high microbial biomass. Each soil section was used for chemical extraction, microbial enumeration, and grain size distribution. Results show that the soil sections with more permeable sediment materials corresponded with higher biomass (total anaerobes > 2 x 106cells/g) and significant contaminant degradation. However, those sections with less permeable sediments contained lower microbial population. Results indicate that the subsurface microorganisms were distributed unevenly in the aquifer, and some regions were devoid of microorganisms and biodegradation activities. Spatial distribution of microorganisms, soil materials, and biogeochemical characteristics in the subsurface soils control the extent and kinetics of contaminant biodegradation. Thus, using blended aquifer materials for measurement of in situ biodegradation rates may not achieve representative results.


2019 ◽  
Vol 24 (42) ◽  
pp. 4991-5008 ◽  
Author(s):  
Mohammed S. Algahtani ◽  
Abdul Aleem Mohammed ◽  
Javed Ahmad

Three-dimensional printing (3DP) has a significant impact on organ transplant, cosmetic surgery, surgical planning, prosthetics and other medical fields. Recently, 3 DP attracted the attention as a promising method for the production of small-scale drug production. The knowledge expansion about the population differences in metabolism and genetics grows the need for personalised medicine substantially. In personalised medicine, the patient receives a tailored dose and the release profile is based on his pharmacokinetics data. 3 DP is expected to be one of the leading solutions for the personalisation of the drug dispensing. This technology can fabricate a drug-device with complicated geometries and fillings to obtain the needed drug release profile. The extrusionbased 3 DP is the most explored method for investigating the feasibility of the technology to produce a novel dosage form with properties that are difficult to achieve using the conventional industrial methods. Extrusionbased 3 DP is divided into two techniques, the semi-solid extrusion (SSE) and the fused deposition modeling (FDM). This review aims to explain the extrusion principles behind the two techniques and discuss their capabilities to fabricate novel dosage forms. The advantages and limitations observed through the application of SSE and FDM for fabrication of drug dosage forms were discussed in this review. Further exploration and development are required to implement this technology in the healthcare frontline for more effective and personalised treatment.


2021 ◽  
Vol 9 (6) ◽  
pp. 585
Author(s):  
Minghao Wu ◽  
Leen De Vos ◽  
Carlos Emilio Arboleda Chavez ◽  
Vasiliki Stratigaki ◽  
Maximilian Streicher ◽  
...  

The present work introduces an analysis of the measurement and model effects that exist in monopile scour protection experiments with repeated small scale tests. The damage erosion is calculated using the three dimensional global damage number S3D and subarea damage number S3D,i. Results show that the standard deviation of the global damage number σ(S3D)=0.257 and is approximately 20% of the mean S3D, and the standard deviation of the subarea damage number σ(S3D,i)=0.42 which can be up to 33% of the mean S3D. The irreproducible maximum wave height, chaotic flow field and non-repeatable armour layer construction are regarded as the main reasons for the occurrence of strong model effects. The measurement effects are limited to σ(S3D)=0.039 and σ(S3D,i)=0.083, which are minor compared to the model effects.


2018 ◽  
Vol 64 (247) ◽  
pp. 745-758 ◽  
Author(s):  
E. DE ANDRÉS ◽  
J. OTERO ◽  
F. NAVARRO ◽  
A. PROMIŃSKA ◽  
J. LAPAZARAN ◽  
...  

ABSTRACTWe have developed a two-dimensional coupled glacier–fjord model, which runs automatically using Elmer/Ice and MITgcm software packages, to investigate the magnitude of submarine melting along a vertical glacier front and its potential influence on glacier calving and front position changes. We apply this model to simulate the Hansbreen glacier–Hansbukta proglacial–fjord system, Southwestern Svalbard, during the summer of 2010. The limited size of this system allows us to resolve some of the small-scale processes occurring at the ice–ocean interface in the fjord model, using a 0.5 s time step and a 1 m grid resolution near the glacier front. We use a rich set of field data spanning the period April–August 2010 to constrain, calibrate and validate the model. We adjust circulation patterns in the fjord by tuning subglacial discharge inputs that best match observed temperature while maintaining a compromise with observed salinity, suggesting a convectively driven circulation in Hansbukta. The results of our model simulations suggest that both submarine melting and crevasse hydrofracturing exert important controls on seasonal frontal ablation, with submarine melting alone not being sufficient for reproducing the observed patterns of seasonal retreat. Both submarine melt and calving rates accumulated along the entire simulation period are of the same order of magnitude, ~100 m. The model results also indicate that changes in submarine melting lag meltwater production by 4–5 weeks, which suggests that it may take up to a month for meltwater to traverse the englacial and subglacial drainage network.


2020 ◽  
Vol 2020 ◽  
pp. 1-13
Author(s):  
Carlo Alberto Niccolini Marmont Du Haut Champ ◽  
Fabrizio Stefani ◽  
Paolo Silvestri

The aim of the present research is to characterize both experimentally and numerically journal bearings with low radial clearances for rotors in small-scale applications (e.g., microgas turbines); their diameter is in the order of ten millimetres, leading to very small dimensional clearances when the typical relative ones (order of 1/1000) are employed; investigating this particular class of journal bearings under static and dynamic loading conditions represents something unexplored. To this goal, a suitable test rig was designed and the performance of its bearings was investigated under steady load. For the sake of comparison, numerical simulations of the lubrication were also performed by means of a simplified model. The original test rig adopted is a commercial rotor kit (RK), but substantial modifications were carried out in order to allow significant measurements. Indeed, the relative radial clearance of RK4 RK bearings is about 2/100, while it is around 1/1000 in industrial bearings. Therefore, the same original RK bearings are employed in this new test rig, but a new shaft was designed to reduce their original clearance. The new custom shaft allows to study bearing behaviour for different clearances, since it is equipped with interchangeable journals. Experimental data obtained by this test rig are then compared with further results of more sophisticated simulations. They were carried out by means of an in-house developed finite element (FEM) code, suitable for thermoelasto-hydrodynamic (TEHD) analysis of journal bearings both in static and dynamic conditions. In this paper, bearing static performances are studied to assess the reliability of the experimental journal location predictions by comparing them with the ones coming from already validated numerical codes. Such comparisons are presented both for large and small clearance bearings of original and modified RKs, respectively. Good agreement is found only for the modified RK equipped with small clearance bearings (relative radial clearance 8/1000), as expected. In comparison with two-dimensional lubrication analysis, three-dimensional simulation improves prediction of journal location and correlation with experimental results.


2015 ◽  
Vol 19 (11) ◽  
pp. 4531-4545 ◽  
Author(s):  
J. Zhu ◽  
C. L. Winter ◽  
Z. Wang

Abstract. Computational experiments are performed to evaluate the effects of locally heterogeneous conductivity fields on regional exchanges of water between stream and aquifer systems in the Middle Heihe River basin (MHRB) of northwestern China. The effects are found to be nonlinear in the sense that simulated discharges from aquifers to streams are systematically lower than discharges produced by a base model parameterized with relatively coarse effective conductivity. A similar, but weaker, effect is observed for stream leakage. The study is organized around three hypotheses: (H1) small-scale spatial variations of conductivity significantly affect regional exchanges of water between streams and aquifers in river basins, (H2) aggregating small-scale heterogeneities into regional effective parameters systematically biases estimates of stream–aquifer exchanges, and (H3) the biases result from slow paths in groundwater flow that emerge due to small-scale heterogeneities. The hypotheses are evaluated by comparing stream–aquifer fluxes produced by the base model to fluxes simulated using realizations of the MHRB characterized by local (grid-scale) heterogeneity. Levels of local heterogeneity are manipulated as control variables by adjusting coefficients of variation. All models are implemented using the MODFLOW (Modular Three-dimensional Finite-difference Groundwater Flow Model) simulation environment, and the PEST (parameter estimation) tool is used to calibrate effective conductivities defined over 16 zones within the MHRB. The effective parameters are also used as expected values to develop lognormally distributed conductivity (K) fields on local grid scales. Stream–aquifer exchanges are simulated with K fields at both scales and then compared. Results show that the effects of small-scale heterogeneities significantly influence exchanges with simulations based on local-scale heterogeneities always producing discharges that are less than those produced by the base model. Although aquifer heterogeneities are uncorrelated at local scales, they appear to induce coherent slow paths in groundwater fluxes that in turn reduce aquifer–stream exchanges. Since surface water–groundwater exchanges are critical hydrologic processes in basin-scale water budgets, these results also have implications for water resources management.


Author(s):  
Pal Kostka ◽  
Zsolt Techy ◽  
James J. Sienicki

Hydrogen combustion may represent a threat to containment integrity in a VVER-440/213 plant owing to the combination of high pressure and high temperature. A study has been carried out using the GASFLOW 2.1 three-dimensional CFD code to evaluate the hydrogen distribution in the containment during a beyond design basis accident. The VVER-440/213 containment input model consists of two 3D blocks connected via one-dimensional (1D) ducts. One 3D block contains the reactor building and the accident localization tower with the suppression pools. Another 3D block models the air traps. 1D ducts represent the check valves connecting the accident localization tower with the air traps. The VVER pressure suppression system, called “bubbler condenser,” was modeled as a distributed heat sink with water thermodynamic properties. This model accounts for the energy balance. However, it is not currently possible to model dynamic phenomena associated with the water pools (e.g., vent clearing, level change). The GASFLOW 2.1 calculation gave detailed results for the spatial distribution of thermal-hydraulic parameters and gas concentrations. The range and trend of the parameters are reasonable and valuable. There are particularly interesting circulation patterns around the steam generators, in the bubbler tower and other primary system compartments. In case of the bubbler tower, concentration and temperature contour plots show an inhomogeneous distribution along the height and width, changing during the accident. Hydrogen concentrations also vary within primary system compartments displaying lower as well as higher (up to 13–20% and higher) values in some nodes. Prediction of such concentration distributions was not previously possible with lumped parameter codes. GASFLOW 2.1 calculations were compared with CONTAIN 1.2 (lumped parameter code) results. Apart from the qualitatively similar trends, there are, for the time being, quantitative differences between the results concerning, for example, pressure histories, or the total amount of steam available in the containment. The results confirm the importance of detailed modeling of the containment, as well as of the bubbler condenser and sump water pools. The study showed that modeling of hydrogen distribution in the VVER-440/213 containment was possible using the GASFLOW 2.1 code with reasonable results and remarkable physical insights.


1996 ◽  
Vol 328 ◽  
pp. 345-407 ◽  
Author(s):  
C. H. K. Williamson

It is now well-known that the wake transition regime for a circular cylinder involves two modes of small-scale three-dimensional instability (modes A and B), depending on the regime of Reynolds number (Re), although almost no understanding of the physical origins of these instabilities, or indeed their effects on near-wake formation, have hitherto been made clear. We address these questions in this paper. In particular, it is found that the two different modes A and B scale on different physical features of the flow. Mode A has a larger spanwise wavelength of around 3–4 diameters, and scales on the larger physical structure in the flow, namely the primary vortex core. The wavelength for mode A is shown to be the result of an ‘elliptic instability’ in the nearwake vortex cores. The subsequent nonlinear growth of vortex loops is due to a feedback from one vortex to the next, involving spanwise-periodic deformation of core vorticity, which is then subject to streamwise stretching in the braid regios. This mode gives an out-of-phase streamwise vortex pattern.In contrast, mode-B instability has a distinctly smaller wavelength (1 diameter) which scales on the smaller physical structure in the flow, the braid shear layer. It is a manifestation of an instability in a region of hyperbolic flow. It is quite distinct from other shear flows, in that it depends on the reverse flow of the bluff-body wake; the presence of a fully formed streamwise vortex system, brought upstream from a previous half-cycle, in proximity to the newly evolving braid shear layer, leads to an in-phase stream-wise vortex array, in strong analogy with the ‘Mode 1’ of Meiburg & Lasheras (1988) for a forced unseparated wake. In mode B, we also observe amalgamation of streamwise vortices from a previous braid with like-sign vortices in the subsequent braid.It is deduced that the large scatter in previous measurements concerning mode A is due to the presence of vortex dislocations. Dislocations are triggered at the sites of some vortex loops of mode A, and represent a natural breakdown of the periodicity of mode A instability. By minimizing or avoiding the dislocations which occur from end contamination or which occur during wake transition, we find an excellent agreement of both critical Re and spanwise wavelength of mode A with the recent secondary stability analysis of Barkley & Henderson (1996).Wake transition is further characterized by velocity and pressure measurements. It is consistent that, when mode-A instability and large-scale dislocations appear, one finds a reduction of base suction, a reduction of (two-dimensional) Reynolds stress level, a growth in size of the formation region, and a corresponding drop in Strouhal frequency. Finally, the present work leads us to a new clarification of the possible flow states through transition. Right through this regime of Re, there exist two distinct and continuous Strouhal frequency curves: the upper one corresponds with purley small- scale instabilities (e.g. denoted as mode A), while the lower curve corresponds with a combination of small-scale plus dislocation structures (e.g. mode A*). However, some of the flow states are transient or ‘unstable’, and the natural transitioning wake appears to follow the scenario: (2D→A*→B).


Sign in / Sign up

Export Citation Format

Share Document