Adsorption characteristics of bio-adsorbent on chromium(III) in industrial wastewater

2015 ◽  
Vol 72 (7) ◽  
pp. 1051-1061 ◽  
Author(s):  
Zhufeng Lu ◽  
Hongmei Wang ◽  
Jiayou Li ◽  
Lixia Yuan ◽  
Lianwen Zhu
Keyword(s):  
Industrial Wastewater ◽  
Adsorption Mechanism ◽  
Physical Adsorption ◽  
Low Cost ◽  
Hydroxyl Groups ◽  
Order Model ◽  
Surface Hydroxyl ◽  
Freundlich Equation ◽  
Simple Chemical ◽  
Pseudo Second Order

The removal of chromium(III) (Cr(III)) from industrial wastewater by various low-cost methods has been widely investigated. In this paper, a type of bio-adsorbent was prepared using rice straw modified by fermentation and simple chemical treatment. The aim is to detect the adsorption mechanism and characteristics on Cr(III) ions. The analysis shows that the bio-adsorbent possesses four modified characteristics for Cr(III) adsorption. The first one is the acquired physical adsorption involving concave and convex structures. The second one is the effects of the hydrogen bonding surface hydroxyl groups and the metal chromium ion with complexation. The third one is mainly caused by hydrophilic active groups that possess carboxyl and hydroxyl groups during microbial degradation to combine with ions. The final one is the bio-adsorbent had high adsorption for low concentration of Cr(III) ions. The highest removal of around 97.45% was obtained at pH 5.0, bio-adsorption dosage of 0.5 g L−1, and initial Cr(III) concentration of 20 mg L−1. The adsorption process followed the pseudo second-order model (R2 > 0.99), while the isotherms were fitted to the Freundlich equation (68.1926 mg g−1), mainly by chemical adsorption. This study demonstrates the potential of using this biosorbent to remove Cr(III) from both synthetic and industrial wastewater.

Isotherm, Kinetics, and Adsorption Mechanism Studies of DTPA-Modified Banana/Pomegranate Peels as Efficient Adsorbents for Removing Cd(II) and Ni(II) from Aqueous Solution

2021 ◽  
Author(s):  
Fanghui Wang ◽  
Peng Wu ◽  
Lin Shu ◽  
Qingbin Guo ◽  
Di Huang ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Adsorption Mechanism ◽  
Physical Adsorption ◽  
Order Model ◽  
X Ray ◽  
Synthetic Materials ◽  
Pseudo Second Order ◽  
Cost Efficient ◽  
First Time ◽  
Sewage Systems

Abstract Two novel absorbents were synthesized for the first time by banana and pomegranate peels using diethylenetriaminepentaacetic acid (DTPA) modification to eliminate Cd(II) and Ni(II) of sewage. The DTPA-modified peels performed significantly higher adsorption capacity than unmodified materials. Adsorption isotherm and kinetics models were simulated to determine their removal efficiency and potential for recovery of these two heavy metals. As the results, the adsorption reached equilibrium within 5 minutes and was well described by the pseudo-second order model and Langmuir isotherm. The surface morphology analysis of the synthetic materials by Scanning Electron Microscopy-Energy Dispersive X-ray spectroscopy, Fourier Transform Infrared spectroscopy and X-ray Photoelectron Spectroscopy, implied that ion exchange, complexation and physical adsorption may together contribute to Cd(II) and Ni(II) loading on DTPA-modified peels. This study demonstrates the feasibility of waste peels as cost-efficient bio-absorbents to remove Cd(II) and Ni(II) in sewage systems, and discovers potential adsorption mechanism of efficiency improvements after DTPA modification.

scholarly journals Equilibrium and Kinetic Study of Anionic and Cationic Pollutants Remediation by Limestone–Chitosan–Alginate Nanocomposite from Aqueous Solution

Molecules ◽  
2021 ◽  
Vol 26 (9) ◽  
pp. 2586
Author(s):  
Inas A. Ahmed ◽  
Ahmed H. Ragab ◽  
Mohamed A. Habila ◽  
Taghrid S. Alomar ◽  
Enas H. Aljuhani
Keyword(s):  
Physical Adsorption ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
Entropy Change ◽  
Sem Images ◽  
Bet Analysis ◽  
Adsorption Processes ◽  
Equilibrium Data ◽  
Pseudo Second Order ◽  
Multilayer Formation

In this work, low-cost and readily available limestone was converted into nanolimestone chitosan and mixed with alginate powder and precipitate to form a triple nanocomposite, namely limestone—chitosan–alginate (NLS/Cs/Alg.), which was used as an adsorbent for the removal of brilliant green (BG) and Congo red (CR) dyes in aqueous solutions. The adsorption studies were conducted under varying parameters, including contact time, temperature, concentration, and pH. The NLS/Cs/Alg. was characterized by SEM, FTIR, BET, and TEM techniques. The SEM images revealed that the NLS/Cs/Alg. surface structure had interconnected pores, which could easily trap the pollutants. The BET analysis established the surface area to be 20.45 m2/g. The recorded maximum experimental adsorption capacities were 2250 and 2020 mg/g for CR and BG, respectively. The adsorption processes had a good fit to the kinetic pseudo second order, which suggests that the removal mechanism was controlled by physical adsorption. The CR and BG equilibrium data had a good fit for the Freundlich isotherm, suggesting that adsorption processes occurred on the heterogeneous surface with a multilayer formation on the NLS/Cs/Alg. at equilibrium. The enthalpy change (ΔH0) was 37.7 KJ mol−1 for CR and 8.71 KJ mol−1 for BG, while the entropy change (ΔS0) was 89.1 J K−1 mol−1 for CR and 79.1 J K−1 mol−1 BG, indicating that the adsorption process was endothermic and spontaneous in nature.

scholarly journals High catalytic activity for formaldehyde oxidation of an interconnected network structure composed of δ-MnO2 nanosheets and γ-MnOOH nanowires

2020 ◽  
Vol 8 (4) ◽  
pp. 429-439
Author(s):  
Ying Tao ◽  
Rong Li ◽  
Ai-Bin Huang ◽  
Yi-Ning Ma ◽  
Shi-Dong Ji ◽  
...  
Keyword(s):  
Catalytic Activity ◽  
Network Structure ◽  
Manganese Oxides ◽  
Active Oxygen Species ◽  
Low Cost ◽  
High Dispersion ◽  
Hydroxyl Groups ◽  
High Catalytic Activity ◽  
Interconnected Network ◽  
Surface Hydroxyl

AbstractAmong the transition metal oxide catalysts, manganese oxides have great potential for formaldehyde (HCHO) oxidation at ambient temperature because of their high activity, nontoxicity, low cost, and polybasic morphologies. In this work, a MnO2-based catalyst (M-MnO2) with an interconnected network structure was successfully synthesized by a one-step hydrothermal method. The M-MnO2 catalyst was composed of the main catalytic agent, δ-MnO2 nanosheets, dispersed in a nonactive framework material of γ-MnOOH nanowires. The catalytic activity of M-MnO2 for HCHO oxidation at room temperature was much higher than that of the pure δ-MnO2 nanosheets. This is attributed to the special interconnected network structure. The special interconnected network structure has high dispersion and specific surface area, which can provide more surface active oxygen species and higher surface hydroxyl groups to realize rapid decomposition of HCHO.

Kinetic Study of Methyl Orange Adsorption from Solution by IOCZ

2013 ◽  
Vol 684 ◽  
pp. 194-197
Author(s):  
Yi Ke Li ◽  
Bing Lu Zhao ◽  
Wei Xiao ◽  
Run Ping Han ◽  
Yan Qiang Li
Keyword(s):  
Methyl Orange ◽  
Contact Time ◽  
Adsorption Mechanism ◽  
Order Model ◽  
Initial Concentration ◽  
Pseudo Second Order ◽  
Adsorption From Solution ◽  
Adsorption Quantity ◽  
Regressive Analysis

The effect of contact time and the determination of the kinetic parameters of adsorption of methyl orange (MO) from aqueous solution onto Iron-Oxide-Coated-Zeolite (IOCZ) powder are important in understanding the adsorption mechanism. The effect of contact time on adsorption quantity was studied at different initial concentration and temperature, respectively. The pseudo-second-order model was adopted to fit the experimental data using non-linear regressive analysis and it was used to predict the adsorption behavior. The results showed that the process of adsorption MO was endothermic and chemisorption. The pore diffusion was not significant.

Removal of Methylene Blue Dye by Using Eggshell Powder

2013 ◽  
Vol 65 (1) ◽  
Author(s):  
Norzita Ngadi ◽  
Chin Chiek Ee ◽  
Nor Aida Yusoff
Keyword(s):  
Methylene Blue ◽  
Textile Industry ◽  
Low Cost ◽  
Kinetic Studies ◽  
Operating Conditions ◽  
Blue Dye ◽  
Dye Wastewater ◽  
Order Model ◽  
Aquatic Life ◽  
Pseudo Second Order

Dyes contain carcinogenic materials which can cause serious hazards to aquatic life and the users of water. Textile industry is the main source of dye wastewater which results in environmental pollution. Many studies have been conducted to investigate the use of low cost adsorbent as an alternative technique for the adsorption of dye. The objective of this study is to determine the potential of eggshell powder as an adsorbent for methylene blue removal and find out the best operating conditions for the color adsorption at laboratory scale. The adsorption of cationic methylene blue from aqueous solution onto the eggshell powder was carried out by varying the operating parameters which were contact time, pH, dosage of eggshell powder and temperature in order to study their effect in adsorption capacity of eggshell powder. The results obtained showed that the best operating condition for removal of methylene blue was at pH 10 (78.98 %) and temperature 50°C (47.37 %) by using 2 g of eggshell powder (57.03 %) with 30 minutes equilibrium time (41.36 %). The kinetic studies indicated that pseudo-second-order model best described the adsorption process.

Polyaniline/ZnO nanocomposites for the removal of methyl orange dye from waste water

2018 ◽  
Vol 32 (19) ◽  
pp. 1840085 ◽  
Author(s):  
Neha V. Nerkar ◽  
Subhash B. Kondawar ◽  
Snehal Kargirwar Brahme ◽  
Yun Hae Kim
Keyword(s):  
Waste Water ◽  
Methyl Orange ◽  
Adsorption Mechanism ◽  
Second Order ◽  
Pure Pani ◽  
Time Interval ◽  
Order Model ◽  
Vis Spectroscopy ◽  
Pseudo Second Order ◽  
Second Order Model

In this paper, we report the safe removal of methyl orange (MO) dye from aqueous solution using chemical interaction of dye molecule with polyaniline/zinc oxide (PANI/ZnO) nanocomposite. PANI/ZnO nanocomposite has been prepared by in situ polymerization. PANI/ZnO nanocomposite was found to be the best promising candidate for adsorption of dyes due to more porosities compared to that of pure PANI. In the present investigation, PANI/ZnO nanocomposite was mixed in a solution of MO dye and used for adsorption process. Color removal was studied using UV-Vis spectroscopy and the spectra were recorded for specific time interval and validation of kinetic model has been applied. Absorbance of PANI/ZnO nanocomposite was found to be increased as compared to that of pure ZnO nanoparticles and pure PANI due to synergistic effect. Comparatively, the removal of dye was also found to be more by using PANI/ZnO nanocomposites. In order to evaluate kinetic mechanism the pseudo-first-order model, pseudo-second-order model and intraparticle diffusion models were verified by the linear equation analysis. Adsorption mechanism of pseudo-second-order model was systematically explained for removal of dye using PANI/ZnO nanocomposite. The results clearly demonstrated that the adsorption mechanism gives very novel and green method of removal of hazardous dyes from waste water.

scholarly journals Synthesis Fe3O4/Talc nanocomposite by coprecipition-ultrasonication method and advances in hexavalent chromium removal from aqueous solution

2020 ◽  
Vol 38 (9-10) ◽  
pp. 483-501
Author(s):  
Nguyen Thi Huong ◽  
Nguyen Ngoc Son ◽  
Vo Hoang Phuong ◽  
Cong Tien Dung ◽  
Pham Thi Mai Huong ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Adsorption Process ◽  
Low Cost ◽  
Batch Experiments ◽  
X Ray Diffraction ◽  
Order Model ◽  
X Ray ◽  
Pseudo Second Order ◽  
Ft Ir ◽  
Langmuir And Freundlich Equations

The Fe3O4/Talc nanocomposite was synthesized by the coprecipitation-ultrasonication method. The reaction was carried out under a inert gas environment. The nanoparticles were characterized by X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM), fourier-transform infrared spectroscopy (FT-IR) and vibrating sample magnetometry techniques (VSM), the surface area of the nanoparticles was determined to be 77.92 m2/g by Brunauer-Emmett-Teller method (BET). The kinetic data showed that the adsorption process fitted with the pseudo-second order model. Batch experiments were carried out to determine the adsorption kinetics and mechanisms of Cr(VI) by Fe3O4/Talc nanocomposite. The adsorption process was found to be highly pH-dependent, which made the material selectively adsorb these metals from aqueous solution. The isotherms of adsorption were also studied using Langmuir and Freundlich equations in linear forms. It is found that the Langmuir equation showed better linear correlation with the experimental data than the Freundlich. The thermodynamics of Cr(VI) adsorption onto the Fe3O4/Talc nanocomposite indicated that the adsorption was exothermic. The reusability study has proven that Fe3O4/Talc nanocomposite can be employed as a low-cost and easy to separate.

Preparation of bio-based magnetic adsorbent and application for efficient removal of Cd(II) from water

2018 ◽  
Vol 77 (5) ◽  
pp. 1313-1323 ◽  
Author(s):  
Jianjun Zhou ◽  
Xionghui Ji ◽  
Xiaohui Zhou ◽  
Jialin Ren ◽  
Yaochi Liu
Keyword(s):  
Aqueous Solution ◽  
Adsorption Process ◽  
Low Cost ◽  
Maximum Adsorption Capacity ◽  
Magnetic Adsorbent ◽  
Order Model ◽  
Efficient Removal ◽  
Adsorption Ability ◽  
Adsorption Sites ◽  
Pseudo Second Order

Abstract A novel magnetic bio-adsorbent (MCIA) was developed, characterized and tested for its Cd(II) removal from aqueous solution. MCIA could be easily separated from the solution after equilibrium adsorption due to its super-paramagnetic property. The functional and magnetic bio-material was an attractive adsorbent for the removal of Cd(II) from aqueous solution owing to the abundant adsorption sites, amino-group and oxygen-containing groups on the surface of Cyclosorus interruptus. The experimental results indicated that the MCIA exhibited excellent adsorption ability and the adsorption process was spontaneous and endothermic. The adsorption isotherm was consistent with the Langmuir model. The adsorption kinetic fitted the pseudo-second-order model very well. The maximum adsorption capacity of Cd(II) onto MCIA was 40.8, 49.4, 54.6 and 56.6 mg/g at 293, 303, 313 and 323 K, respectively. And the MCIA exhibited an excellent reusability and impressive regeneration. Therefore, MCIA could serve as a sustainable, efficient and low-cost magnetic adsorbent for Cd(II) removal from aqueous solution.

Highly effective removal of Cu(II) in aqueous solution by using mesoporous TiO2

2019 ◽  
Vol 80 (5) ◽  
pp. 884-891
Author(s):  
Daying Chen ◽  
Nasi Tu ◽  
Changkun Si ◽  
Meilin Yin ◽  
Xiaohui Wang
Keyword(s):  
Aqueous Solution ◽  
Low Cost ◽  
Sol Gel ◽  
Mesoporous Tio2 ◽  
Adsorption Efficiency ◽  
Batch Experiments ◽  
Order Model ◽  
Effective Removal ◽  
Pseudo Second Order ◽  
Gel Processing

Abstract Mesoporous TiO2 has been prepared by a brief and simple sol–gel processing and applied for the removal of Cu(II) from aqueous solution. The adsorption behavior of mesoporous TiO2 for Cu(II) was investigated using batch experiments. Results showed that the pseudo-second-order model and Langmuir isotherm were more accurate to describe the kinetics process and adsorption isotherm. Mesoporous TiO2 adsorbent displayed excellent Cu(II) adsorption efficiency (195.52mg g−1). The thermodynamic parameters showed that the adsorption was spontaneous and endothermic. It was also found that mesoporous TiO2 could be used at least seven times without obvious loss of its original adsorption efficiency. Therefore, the obtained mesoporous TiO2 could be employed as an effective and low-cost adsorbent for removal of Cu(II) from contaminated effluents.

scholarly journals Simultaneous Adsorption of Cr(VI) and Phenol from Binary Mixture Using Iron Incorporated Rice Husk: Insight to Multicomponent Equilibrium Isotherm

2016 ◽  
Vol 2016 ◽  
pp. 1-11 ◽  
Author(s):  
Ankur Gupta ◽  
Chandrajit Balomajumder
Keyword(s):  
Experimental Data ◽  
Rice Husk ◽  
Low Cost ◽  
Binary Solution ◽  
Multicomponent System ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
Order Model ◽  
Adsorption Isotherm Models ◽  
Pseudo Second Order

Fe modified rice husk was prepared as a low cost biosorbent for the removal of Cr(VI) and phenol both singly and in combination from single and binary simulated synthetic waste water. Rice husk was modified by treating with FeSO4·7H2O. The results showed that impregnation of iron onto the surface of rice husk improved the adsorption capability of both Cr(VI) and phenol. The effects of process parameters for multicomponent system such as pH, adsorbent dose, and contact time onto the percentage removal of both Cr(VI) and phenol were investigated. The experimental data for the adsorption of both Cr(VI) and phenol onto the surface of Fe modified rice husk applied to various kinetic and adsorption isotherm models. Multicomponent isotherm models such as Nonmodified Langmuir, Modified Langmuir, Extended Langmuir, Extended Freundlich, Competitive Nonmodified Redlich Peterson, Competitive Modified Redlich Peterson were applied. The results show that Extended Freundlich model best described the experimental data for both Cr(VI) and phenol from binary solution. Pseudo second-order model agreed well with Cr(VI) while pseudo first-order model agreed well with phenol. Maximum adsorption capacity in synthetic binary solution of Cr(VI) and phenol was found to be 36.3817 mg g−1for Cr(VI) and 6.569 mg g−1for phenol, respectively.

Sign in / Sign up

Export Citation Format

Share Document