scholarly journals Studies on desorption and regeneration of natural pumice for iron removal from aqueous solution

2018 ◽  
Vol 2017 (2) ◽  
pp. 509-515 ◽  
Author(s):  
S. Indah ◽  
D. Helard ◽  
A. Binuwara
Keyword(s):  
Aqueous Solution ◽  
Removal Efficiency ◽  
Contact Time ◽  
Adsorption Process ◽  
Iron Removal ◽  
Iron Ions ◽  
The Third ◽  
Environmental Friendly ◽  
West Sumatra ◽  
Adsorption Desorption

Abstract To make the adsorption process more economic and environmental friendly, it is necessary to study desorption and reutilization of the adsorbents. In the present study, the effectiveness of natural pumice in removal of iron from aqueous solution was investigated in several sorption-desorption cycles. The desorption characteristics of previously adsorbed iron ions on natural pumice were tested by various desorbing agents such as HCl, NaOH and aquadest. Among them, HCl showed the highest desorption efficiency (37.89%) with 0.1 M of concentration and 60 min of contact time. The removal efficiency of iron ions in reused natural pumice could be maintained up to 90% in the third cycle of adsorption. The results indicate that although complete desorption was not achieved, natural pumice from Sungai Pasak, West Sumatra, Indonesia, can be sufficiently reused up to three cycles of adsorption-desorption.

scholarly journals Microcrystalline cellulose (MCC) as an adsorbent in copper removal from aqueous solution

2021 ◽  
Vol 1195 (1) ◽  
pp. 012022
Author(s):  
N A Khalil ◽  
N S Abdullah ◽  
A S A Rahman ◽  
H A Hamid ◽  
A N S Fizal ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Adsorption Capacity ◽  
Removal Efficiency ◽  
Microcrystalline Cellulose ◽  
Contact Time ◽  
Adsorption Process ◽  
Adsorption Parameters ◽  
Temperature Ranges ◽  
Higher Temperature ◽  
Lower Temperature

Abstract Many studies have been done on the natural adsorbent, natural/raw cellulose, modified cellulose and modified MCC as media for removing copper. However, the usage of unmodified microcrystalline cellulose (MCC) as an adsorbent to remove heavy metals contaminants such as copper from an aqueous solution is scarcely being explored. Thus, the current study was done to assess the performance of the MCC, without any modification, based on the adsorption capacity and the Cu removal efficiency under varied process parameters. The MCC was successfully used for Cu2+ or Cu (II) removal at pH < pH6. The adsorption parameters such as pH (1 to 6), contact time (0.5 to 24 hours), temperature (25 to 70 °C), initial Cu concentrations (1 to 5 mg/L) and MCC dosage (0.05 to 0.5 g) were significantly influenced the adsorption performance of the MCC. This study indicated the adsorption process occurred at pH ranging from pH 2.8 to 6 with 3 to 24 hours of duration were required to achieve the equilibrium condition. Lower temperature ranges (25 to 30 °C) were more favourable for adsorption than higher temperature ranges (40 to 70 °C). The increase in initial Cu concentration enhanced the adsorption capacity of MCC but decreased Cu removal. On the other hand, the increase in the MCC dosage resulted in the decreased adsorption capacity, however, increased Cu removal. MCC dosage of 0.225 g managed to remove Cu (II) with 95% efficiency at the initial Cu concentration of 1 mg/L, pH 5 and temperature 25 °C within 24 hours of contact time with 0.18 mg/g of adsorption capacity. Overall, high Cu removal efficiency (up to 95%) was achieved by the MCC which render its usage as adsorbent.

Utilisation of Biomass and Hybrid Biochar from Elephant Grass and Low Density Polyethylene for the Competitive Adsorption of Pb(II), Cu(II), Fe(II) and Zn(II) from Aqueous Media

2020 ◽  
Vol 13 ◽  
Author(s):  
Joshua O. Ighalo ◽  
Lois T. Arowoyele ◽  
Samuel Ogunniyi ◽  
Comfort A. Adeyanju ◽  
Folasade M. Oladipo-Emmanuel ◽  
...  
Keyword(s):  
Heavy Metals ◽  
Removal Efficiency ◽  
Contact Time ◽  
Competitive Adsorption ◽  
Adsorption Process ◽  
Aqueous Media ◽  
Polluted Water ◽  
Batch Adsorption ◽  
Order Kinetic ◽  
Elephant Grass

Background: The presence of pollutants in polluted water is not singularized hence pollutant species are constantly in competition for active sites during the adsorption process. A key advantage of competitive adsorption studies is that it informs on the adsorbent performance in real water treatment applications. Objective: This study aims to investigate the competitive adsorption of Pb(II), Cu(II), Fe(II) and Zn(II) using elephant grass (Pennisetum purpureum) biochar and hybrid biochar from LDPE. Method: The produced biochar was characterised by Scanning Electron Microscopy (SEM) and Fourier Transform Infrared Spectroscopy (FTIR). The effect of adsorption parameters, equilibrium isotherm modelling and parametric studies were conducted based on data from the batch adsorption experiments. Results: For both adsorbents, the removal efficiency was >99% over the domain of the entire investigation for dosage and contact time suggesting that they are very efficient for removing multiple heavy metals from aqueous media. It was observed that removal efficiency was optimal at 2 g/l dosage and contact time of 20 minutes for both adsorbent types. The Elovich isotherm and the pseudo-second order kinetic models were best-fit for the competitive adsorption process. Conclusion: The study was able to successfully reveal that biomass biochar from elephant grass and hybrid biochar from LDPE can be used as effective adsorbent material for the removal of heavy metals from aqueous media. This study bears a positive implication for environmental protection and solid waste management.

scholarly journals Modified/Unmodified Nanoparticle Adsorbents of Cellulose Origin With High Adsorptive Potential for Removal of Pb(II) From Aqueous Solution

2017 ◽  
Vol 13 (27) ◽  
pp. 425
Author(s):  
Azeh Yakubu ◽  
Gabriel Ademola Olatunji ◽  
Folahan Amoo Adekola
Keyword(s):  
Aqueous Solution ◽  
Adsorption Capacity ◽  
Contact Time ◽  
Adsorption Process ◽  
Correlation Coefficients ◽  
Solution Temperature ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
Kinetics Of Adsorption ◽  
Kinetics Of

This investigation was conducted to evaluate the adsorption capacity of nanoparticles of cellulose origin. Nanoparticles were synthesized by acid hydrolysis of microcrystalline cellulose/cellulose acetate using 64% H3PO4 and characterized using FTIR, XRD, TGA-DTGA, BET and SEM analysis. Adsorption kinetics of Pb (II) ions in aqueous solution was investigated and the effect of initial concentration, pH, time, adsorbent dosage and solution temperature. The results showed that adsorption increased with increasing concentration with removal efficiencies of 60% and 92.99% for Azeh2 and Azeh10 respectively for initial lead concentration of 3 mg/g. The effects of contact time showed that adsorption maximum was attained within 24h of contact time. The maximum adsorption capacity and removal efficiency were achieved at pH6. Small dose of adsorbent had better performance. The kinetics of adsorption was best described by the pseudo-second-Order model while the adsorption mechanism was chemisorption and pore diffusion based on intra-particle diffusion model. The isotherm model was Freundlich. Though, all tested isotherm models relatively showed good correlation coefficients ranging from 0.969-1.000. The adsorption process was exothermic for Azeh-TDI, with a negative value of -12.812 X 103 KJ/mol. This indicates that the adsorption process for Pb by Azeh-TDI was spontaneous. Adsorption by Azeh2 was endothermic in nature.

scholarly journals Preparation, Characterization and Adsorption Potential of Grainy Halloysite-CNT Composites for Anthracene Removal from Aqueous Solution

Nanomaterials ◽  
2019 ◽  
Vol 9 (6) ◽  
pp. 890 ◽  
Author(s):  
Gabriela Kamińska ◽  
Mariusz Dudziak ◽  
Edyta Kudlek ◽  
Jolanta Bohdziewicz
Keyword(s):  
Carbon Nanotubes ◽  
Aqueous Solution ◽  
Adsorption Capacity ◽  
Contact Time ◽  
Adsorption Process ◽  
Heating Temperature ◽  
Langmuir Model ◽  
Adsorption Potential ◽  
Adsorption Sites ◽  
Enhanced Adsorption

Grainy Hal-CNT composites were prepared from powder halloysite nanoclay (Hal) and carbon nanotubes (CNTs). The effect of the amount and type of CNTs, as well as calcination temperature on morphology and properties of Hal-CNT composites and their adsorption capacity of anthracene (ANT), were studied. The surface topography of granules was heterogenous, with cracks and channels created during granulation of powder clay and CNTs. In FTIR, spectra were exhibited only in the bands arising from halloysite, due to its dominance in the granules. The increase in the heating temperature to 550 °C resulted in mesoporosity/macroporosity of the granules, the lowest specific surface area (SSA) and poorest adsorption potential. Overall, SSA of all Hal-CNT composites were higher than raw Hal, and by itself, heated halloysite. The larger amount of CNTs enhanced adsorption kinetics due to the more external adsorption sites. The equilibrium was established with the contact time of approximately 30 min for the sample Hal-SWCNT 85:15, while the samples with loading 96:4, it was 60–90 min. Adsorption isotherms for ANT showed L1 type, which is representative for the sorbents with limited adsorption capacity. The Langmuir model described the adsorption process, suggesting a monolayer covering. The sample Hal-SWCNT 85:15 exhibited the highest adsorption capacity of ANT, due to its highest SSA and microporous character.

scholarly journals Batch studies of phosphonate adsorption on granular ferric hydroxides

2020 ◽  
Vol 81 (1) ◽  
pp. 10-20 ◽  
Author(s):  
T. Reinhardt ◽  
M. Gómez Elordi ◽  
R. Minke ◽  
H. Schönberger ◽  
E. Rott
Keyword(s):  
Contact Time ◽  
Room Temperature ◽  
Adsorption Process ◽  
Ferric Hydroxide ◽  
Batch Experiments ◽  
Batch Studies ◽  
Influence Of Temperature ◽  
Ph Values ◽  
Adsorption Desorption ◽  
Granular Ferric Hydroxide

Abstract Phosphonates are widely used in various industries. It is desirable to remove them before discharging phosphonate-containing wastewater. This study describes a large number of batch experiments with adsorbents that are likely suitable for the removal of phosphonates. For this, adsorption isotherms for four different granular ferric hydroxide (GFH) adsorbents were determined at different pH values in order to identify the best performing material. Additionally, the influence of temperature was studied for this GFH. A maximum loading for nitrilotrimethylphosphonic acid (NTMP) was found to be ∼12 mg P/g with an initial concentration of 1 mg/L NTMP-P and a contact time of 7 days at room temperature. Then, the adsorption of six different phosphonates was investigated as a function of pH. It was shown that GFH could be used to remove all investigated phosphonates from water and, with an increasing pH, the adsorption capacity decreased for all six phosphonates. Finally, five adsorption–desorption cycles were carried out to check the suitability of the material for multiple re-use. Even after five cycles, the adsorption process still performed well.

scholarly journals Adsorption of As(V) from Aqueous Solution on Chitosan-Modified Diatomite

2020 ◽  
Vol 17 (2) ◽  
pp. 429 ◽  
Author(s):  
Qintao Yang ◽  
Liang Gong ◽  
Lili Huang ◽  
Qinglin Xie ◽  
Yijian Zhong ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Removal Efficiency ◽  
Ph Effect ◽  
Freundlich Isotherm ◽  
Xrd Analysis ◽  
Optimal Value ◽  
Equilibrium Data ◽  
Pseudo Second Order ◽  
Adsorption Desorption ◽  
Modified Diatomite

A novel chitosan (CS)-modified diatomite (Dt) was prepared by a simple mixture in the mass ratio to remove As(V) from aqueous solution in this research. The CS-modified Dt adsorbent was characterized by scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR), and X-ray powder diffraction (XRD) analysis. The parameters to influence the adsorption of As(V) ion were studied under such conditions as kinetics, adsorption isotherm, and pH effect. The results revealed that adsorption of As(V) was initially rapid and the equilibrium time was reached after 40 min. The optimal value of the pH was 5.0 for better adsorption. The equilibrium data were well fitted to the Langmuir isotherm compared to the Freundlich isotherm, and exhibited the highest capacity and removal efficiency of 94.3% under an initial As(V) concentration of 5 mg/L. The kinetic data were well described by the pseudo-second-order model. In addition, 0.1 M NaOH has the best desorption efficiency of As(V) adsorbed on CS-modified Dt, and the removal efficiency of As(V) was still higher than 90% when after six adsorption-desorption cycles. These results showed that the CS-modified Dt could be considered as a potential adsorbent for the removal of As(V) in aqueous solution.

scholarly journals Phenol removal from aqueous solution using silica and activated carbon derived from rice husk

2019 ◽  
Vol 14 (4) ◽  
pp. 897-907 ◽  
Author(s):  
Hosseinali Asgharnia ◽  
Hamidreza Nasehinia ◽  
Roohollah Rostami ◽  
Marziah Rahmani ◽  
Seyed Mahmoud Mehdinia
Keyword(s):  
Aqueous Solution ◽  
Activated Carbon ◽  
Water Treatment ◽  
Organic Pollutants ◽  
Rice Husk ◽  
Contact Time ◽  
Adsorption Process ◽  
Phenol Removal ◽  
Initial Concentration ◽  
Maximum Removal

Abstract Phenol and its derivatives are organic pollutants with dangerous effects, such as poisoning, carcinogenicity, mutagenicity, and teratogenicity in humans and other organisms. In this study, the removal of phenol from aqueous solution by adsorption on silica and activated carbon of rice husk was investigated. In this regard, the effects of initial concentration of phenol, pH, dosage of the adsorbents, and contact time on the adsorption of phenol were investigated. The results showed that the maximum removal of phenol by rice husk silica (RHS) and rice husk activated carbon (RHAC) in the initial concentration of 1 mgL−1 phenol, 2 gL−1 adsorbent mass, 120 min contact time, and pH 5 (RHS) or pH 6 (RHAC) were obtained up to 91% and 97.88%, respectively. A significant correlation was also detected between increasing contact times and phenol removal for both adsorbents (p &lt; 0.01). The adsorption process for both of the adsorbents was also more compatible with the Langmuir isotherm. The results of this study showed that RHS and RHAC can be considered as natural and inexpensive adsorbents for water treatment.

Application of Oyster (Anadara Inflata) Shell Chitosan as Adsorbent for Heavy Metal Cu(II) Ion

2015 ◽  
Vol 798 ◽  
pp. 390-394
Author(s):  
Saptono Hadi ◽  
Budi Hastuti ◽  
Nurina Tulus Setiawati
Keyword(s):  
Aqueous Solution ◽  
Heavy Metal ◽  
Reaction Time ◽  
Contact Time ◽  
Adsorption Process ◽  
Interaction Mechanism ◽  
Chemical Mechanism ◽  
Optimum Conditions ◽  
Percentage Removal ◽  
Adsorption Capability

Research on the application of chitosan derived from oyster (Anadara inflata) shell as adsorbent for heavy metal Cu (II) has been conducted. Optimum conditions for adsorption, including pH, reaction time, and mass of adsorbent were investigated. Adsorption capability of Cu (II) by chitosan under those optimum conditions was subsequently evaluated by determining their adsorption isotherms and interaction mechanism. The results showed that the optimum condition for adsorption were pH 8, contact time 60 min, and mass of adsorbent 300 mg. Under those optimum conditions, chitosan has a high percentage removal of Cu (II) from aqueous solution, up to 70%. The adsorption process was well described as Langmuir isotherm and it is assumed that the interaction between Cu (II) and chitosan was based on chemical mechanism.

scholarly journals Paraquat dichloride adsorption from aqueous solution using Carbonized Bambara Groundnut (Vigna subterranean) Shells

2020 ◽  
Vol 12 (1) ◽  
pp. 167-177
Author(s):  
Ayuba Abdullahi Muhammad ◽  
Nyijime Thomas Aondofa
Keyword(s):  
Aqueous Solution ◽  
Water Treatment ◽  
Contact Time ◽  
Adsorption Process ◽  
Bambara Groundnut ◽  
Experimental Result ◽  
Isotherm Model ◽  
Batch Adsorption ◽  
Solution Ph ◽  
Adsorbent Dosage

Carbonized Bambara GroundNut Shell (CBGNS) was used as adsorbent for the adsorption of paraquat dichloride (PQ) from aqueous solution. The prepared adsorbent was characterized using scanning electron microscopy (SEM) and Fourier transform infrared (FTIR) spectroscopy methods. Several parameters that might affect the adsorption process including pH, contact time, adsorbent dosage, temperature and initial concentration were investigated and optimized using batch adsorption technique. Results of the study revealed that maximum removal efficiency (98%) was achieved using 0.05g adsorbent dosage, solution pH of 5 and 60 min of contact time. The equilibrium experimental result revealed that Langmuir model best described the adsorption process with R2 value of 0.956.The heat of adsorption process was estimated from Temkin Isotherm model to be 19.99J/mol and the mean free energy was estimated from Duninin-Radushkevich (DRK) isotherm model to be 0.289KJ/mol indicating chemisorptions process. The kinetic and thermodynamic studies revealed that the adsorption processes followed pseudo-second-order kinetics with R2 value of 0.999 and the value of ∆G (- 27.74 kJ mol-1), ∆H (13.145 kJ mol-1) indicate the spontaneous and endothermic nature of PQ adsorption on CBGNS. The results suggested that CBGNS had the potential to become a promising material for PQ contaminated water treatment. Keywords: Adsorption, Paraquat dichloride, Carbonized Bambara Ground nut shell, Water treatment.

scholarly journals Adsorptive Removal of Congo red dye from wastewater using Fenugreek Powder

2020 ◽  
Author(s):  
Neha bhadauria ◽  
Arjun Suresh
Keyword(s):  
Aqueous Solution ◽  
Congo Red ◽  
Contact Time ◽  
Adsorption Process ◽  
Dye Adsorption ◽  
Textile Dye ◽  
Adsorptive Removal ◽  
Congo Red Dye ◽  
Red Dye ◽  
Maximum Removal

The present study analyzed the efficiency of a naturally derived fenugreek powder for removal of Congo red dye from the aqueous solution. The flocculation Studies on Congo Red (CR) a hazardous, textile dye onto Fenugreek Powder and its adsorption was analyzed. Fenugreek Powder is Eco-friendly, biodegradable and locally available in the market. The dye adsorption process was performed in different batches at varying pH, dye concentration, adsorbent concentration and contact time to get the best results. The result showed that the maximum removal of dye was 42.4% with 10mg/l of Fenugreek powder at pH 4.

Sign in / Sign up

Export Citation Format

Share Document