scholarly journals Optimization study of biosorption of toxic metals from mining wastewater using Azadirachta indica bark adsorbents

2020 ◽  
Vol 82 (5) ◽  
pp. 887-904
Author(s):  
Ezekiel A. Adetoro ◽  
Samson O. Ojoawo
Keyword(s):  
Grain Size ◽  
Experimental Design ◽  
Azadirachta Indica ◽  
Toxic Metals ◽  
Contact Time ◽  
Activated Carbons ◽  
Batch Adsorption ◽  
Agitation Rate ◽  
Adsorbent Dosage ◽  
Mining Wastewater

Abstract The effectiveness of two Azadirachta indica bark activated carbons (ABAC) for the removal of selected toxic metals from mining wastewater and the attendant challenge of multivariate factors in the process were enhanced through optimization studies. Experimental design was carried out using adsorbent dosage, agitation rate, contact time, grain size, pH and temperature as independent variables. Batch adsorption experiments were conducted using the experimental design result, then the experimental data obtained were optimized using Design-Expert software and the results validated. Optimum values for ABAC-NaOH adsorbent were 1.999 g of adsorbent dosage, 149.73 rpm agitation rate, 119.55 min contact time, 2 mm grain size, pH of 7 and 30 °C temperature; while for ABAC-HCl adsorbent the optimum values were 3.993 g of adsorbent dosage, 150 rpm agitation rate, 120 min contact time, 2 mm grain size, pH of 7.001 and 30 °C temperature. These resulted in 100% removal efficiencies for all the selected toxic metals with standard errors of between 0.02 and 2.72%. So the optimization process is a very useful tool in adsorption studies. It has the merits of being economical, energy and time saving, and is therefore strongly recommended for the biosorption of toxic metals from mining wastewater using Azadirachta indica adsorbent.

scholarly journals Comparative Adsorptive Removal of Selected Heavy Metals from Battery Wastewater by Purified and Polyethylene Glycol Modified Carbon Nanotubes

2021 ◽  
Author(s):  
Abdulkareem AS ◽  
Hamzat WA ◽  
Tijani JO ◽  
Bankole MT ◽  
Titus Egbosiuba ◽  
...  
Keyword(s):  
Heavy Metals ◽  
Carbon Nanotubes ◽  
Polyethylene Glycol ◽  
Toxic Metals ◽  
Contact Time ◽  
Batch Adsorption ◽  
Adsorption Effect ◽  
Adsorbent Dosage ◽  
Modified Carbon Nanotubes ◽  
Nano Adsorbent

Abstract Comparative adsorption study of some toxic metals (Ni, Fe, Cu, Cd, and Pb) from battery industrial effluent by purified and polyethylene glycol-modified carbon nanotubes (CNTs) is reported. The as-prepared CNTs via chemical vapour deposition method (A-CNTs), its acid purified form (P-CNTs), and polyethylene glycol functionalized form (PEG-CNTs) were characterized by HRTEM, BET, HRSEM, FTIR and XRD. The HRSEM and HRTEM micrograph revealed the formation of multi-walled tubular network structures of different inner and outer diameter. The BET study of PEG-CNTs and purified CNTs showed surface areas of 970.81 m2/g and 781.88 m2/g, respectively. The nanomaterials batch adsorption effect of various parameters such as contact time, nano-adsorbent dosage and temperature was conducted. The optimum equilibrium to achieve maximum removal of Cd (83.41 %), Ni (92.79 %), Fe (95.93%), Pb (97.16 %) Cu (99.9 9%) using PEG-CNTs was 90 min of contact time, 0.3 g of nano-adsorbent dosage and 60 oC temperature. While the maximum percentage removal efficiencies accomplished using P-CNTs under the same applied conditions were Cd (78.64 %), Ni (76.12 %), Fe (92.87 %), Pb (90.7 2%) Cu (99.09 %). PEG-CNTs was seen as more effective than P-CNTs. Adsorption data of Ni on P-CNTs followed Langmuir isotherm while the adsorption equilibrium model (Freundlich isotherm) of Ni, Fe, Cu and Pb on PEG-CNTs were fitted well. However, in both cases, the sorption kinetic study followed the pseudo-second-order model. The thermodynamics showed that the removal of toxic metals from battery wastewater was spontaneous and endothermic irrespective of the nano-adsorbents. The study found that surface modification of CNTs by polyethylene glycol adequately improved the nanotubes, thus leading to relatively adsorption capacities of heavy metals from industrial battery effluent.

scholarly journals The Design and Implementation of Adsorptive Removal of Cu(II) from Leachate Using ANFIS

2013 ◽  
Vol 2013 ◽  
pp. 1-9 ◽  
Author(s):  
Nurdan Gamze Turan ◽  
Okan Ozgonenel
Keyword(s):  
Experimental Design ◽  
Contact Time ◽  
Fixed Bed ◽  
Experimental System ◽  
Factorial Experimental Design ◽  
Adsorbent Dosage ◽  
Initial Ph ◽  
Full Factorial Experimental Design ◽  
Full Factorial ◽  
Aqueous Leachate

Clinoptilolite was investigated for the removal of Cu(II) ions from industrial leachate. Adaptive neural fuzzy interface system (ANFIS) was used for modeling the batch experimental system and predicting the optimal input values, that is, initial pH, adsorbent dosage, and contact time. Experiments were studied under laboratory batch and fixed bed conditions. The outcomes of suggested ANFIS modeling were then compared to a full factorial experimental design (23), which was utilized to assess the effect of three factors on the adsorption of Cu(II) ions in aqueous leachate of industrial waste. It was observed that the optimized parameters are almost close to each other. The highest removal efficiency was found as about 93.65% at pH 6, adsorbent dosage 11.4 g/L, and contact time 33 min for batch conditions of 23experimental design and about 90.43% at pH 5, adsorbent dosage 15 g/L and contact time 35 min for batch conditions of ANFIS. The results show that clinoptilolite is an efficient sorbent and ANFIS, which is easy to implement and is able to model the batch experimental system.

Biosorption of Textile Dye Red Bemacid ETL Using Activated Charcoal of Grape Marc (Oenological By-Product)

2019 ◽  
Vol 800 ◽  
pp. 151-156
Author(s):  
Yamina Chergui ◽  
Abdelkader Iddou ◽  
Hafida Hentit ◽  
Abdallah Aziz ◽  
Jean Claude Jumas
Keyword(s):  
Aqueous Solution ◽  
Zinc Chloride ◽  
Contact Time ◽  
Adsorption Mechanism ◽  
Activated Carbons ◽  
Batch Adsorption ◽  
Textile Dye ◽  
Isothermal Adsorption ◽  
Physical Methods ◽  
Grape Marc

The objective of this study was the synthesis of various activated carbons from grape marc issued from oenological by-product as a biosorbent. The biosolid was then applied to remove an industrial dye (red bemacid ETL) in aqueous solution. Activation of the synthesized charcoal was carried out using a solution of zinc chloride induced by two physical methods (microwaves and heating at 300°C). The obtained materials are characterized by FTIR and SEM methods. Results from batch adsorption tests have shown that pH solution, initial dye concentration and contact time affect the adsorption mechanism. Removal of the industrial dye revealed second order kinetics, exothermic adsorption and isothermal adsorption of BET type.

scholarly journals Paraquat dichloride adsorption from aqueous solution using Carbonized Bambara Groundnut (Vigna subterranean) Shells

2020 ◽  
Vol 12 (1) ◽  
pp. 167-177
Author(s):  
Ayuba Abdullahi Muhammad ◽  
Nyijime Thomas Aondofa
Keyword(s):  
Aqueous Solution ◽  
Water Treatment ◽  
Contact Time ◽  
Adsorption Process ◽  
Bambara Groundnut ◽  
Experimental Result ◽  
Isotherm Model ◽  
Batch Adsorption ◽  
Solution Ph ◽  
Adsorbent Dosage

Carbonized Bambara GroundNut Shell (CBGNS) was used as adsorbent for the adsorption of paraquat dichloride (PQ) from aqueous solution. The prepared adsorbent was characterized using scanning electron microscopy (SEM) and Fourier transform infrared (FTIR) spectroscopy methods. Several parameters that might affect the adsorption process including pH, contact time, adsorbent dosage, temperature and initial concentration were investigated and optimized using batch adsorption technique. Results of the study revealed that maximum removal efficiency (98%) was achieved using 0.05g adsorbent dosage, solution pH of 5 and 60 min of contact time. The equilibrium experimental result revealed that Langmuir model best described the adsorption process with R2 value of 0.956.The heat of adsorption process was estimated from Temkin Isotherm model to be 19.99J/mol and the mean free energy was estimated from Duninin-Radushkevich (DRK) isotherm model to be 0.289KJ/mol indicating chemisorptions process. The kinetic and thermodynamic studies revealed that the adsorption processes followed pseudo-second-order kinetics with R2 value of 0.999 and the value of ∆G (- 27.74 kJ mol-1), ∆H (13.145 kJ mol-1) indicate the spontaneous and endothermic nature of PQ adsorption on CBGNS. The results suggested that CBGNS had the potential to become a promising material for PQ contaminated water treatment. Keywords: Adsorption, Paraquat dichloride, Carbonized Bambara Ground nut shell, Water treatment.

scholarly journals Methylene Blue Adsorption from aqueous solution by low cost vine-wood biomass

2021 ◽  
Author(s):  
Rachida Souidi ◽  
yasmina khane ◽  
Lahcen Belarbi ◽  
Smain Bousalem
Keyword(s):  
Methylene Blue ◽  
Sulfuric Acid ◽  
Contact Time ◽  
Adsorption Process ◽  
Low Cost ◽  
Sulfuric Acid Concentration ◽  
Analytical Techniques ◽  
Batch Adsorption ◽  
Adsorbent Dosage ◽  
Adsorption Desorption

Abstract In this work, the sawdust of vine wood (VW) was treated with sulfuric acid and used to adsorb methylene blue (MB) from aqueous solutions via a batch adsorption process. The characteristics of the adsorbent were determined by various analytical techniques such as Fourier-transform infrared (FT-IR) spectroscopy, X-ray diffraction (XRD) and scanning electron microscopy (SEM) and Brunauer−Emmett−Teller (BET) N2 adsorption−desorption isotherms. The effects of various experimental parameters including sulfuric acid concentration, particle size of the adsorbent, pH of the solution, contact time, initial concentration, adsorbent dosage and temperature on adsorption of MB by activating sawdust were systematically investigated. The experimental results showed that the adsorption efficiency was increased with contact time and adsorbent dosage. The maximum removal efficiency was found after 180 min of solid/liquid contact with adsorbent doses of 1 g/l for sawdust. The isotherm and kinetic experimental data for MB adsorption on VW sawdust were best-fitted by Langmuir models and Pseudo-second-order, respectively. The calculated values of the entropy (ΔS°), enthalpy (ΔH°) and Gibbs energy (ΔG°) indicated that the adsorption process was exothermic in nature. These results suggest that the activated sawdust can be employed as a low-cost and environmentally friendly adsorbent for the treatment of wastewaters containing dyes.

Desorption of Mercury Complex from Fe-Modified Montmorillonite Adsorbent Membrane

2019 ◽  
Vol 814 ◽  
pp. 451-456 ◽  
Author(s):  
Marjorie Jane Lodo ◽  
Leslie Joy L. Diaz
Keyword(s):  
Contact Time ◽  
Environmental Remediation ◽  
Adsorption Process ◽  
Batch Adsorption ◽  
Adsorption Efficiency ◽  
Sem Images ◽  
Modified Montmorillonite ◽  
Subsequent Elution ◽  
Mining Wastewater ◽  
Cyanide Solutions

With the use of nanotechnology, clay minerals, specifically montmorillonites, have been reengineered to be used in environmental remediation, especially in the treatment of mining wastewater containing hazardous heavy metal ions. The objective of this study is to assess the practicality of using iron-modified montmorillonite (Fe-MMT) nanomembranes in the removal of mercury using the adsorption process. The nanomembranes, which were synthesized via electrospinning, were subjected to mercury cyanide solutions during the batch adsorption set ups to determine the adsorption efficiency. During the subsequent elution tests, three factors– eluent type (CH3COOH and C6H807), eluent concentration (0.01 M and 0.05 M) and contact time (3 and 5 hours) – were tested. SEM images of the mats were acquired to study the structure of the adsorbent. HD XRF analysis was done to identify the ions present in the membrane, as well as the initial Hg concentrations, amount of remaining Hg in the wastewater after batch adsorption and amount of desorbed metal. Results showed that using the Fe-MMT nanomembrane as adsorbent material resulted to 61.74% removal of Hg in the mercury cyanide solutions with initial concentrations of 13.87 to 38.9 mg L-1. Acetic acid exhibited better desorption results, with the highest efficiency of 31.36% (0.01 M, 5 h) compared to citric acid’s 7.40% (0.05M, 3 h).

scholarly journals Adsorption Studies of Lead on α- Alumina

1970 ◽  
Vol 44 (4) ◽  
pp. 403-406 ◽  
Author(s):  
Sumra Naeem ◽  
Naseem Zahra ◽  
Uzma Zafar ◽  
Sadia Munawar
Keyword(s):  
Atomic Absorption ◽  
Toxic Metals ◽  
Contact Time ◽  
Batch Adsorption ◽  
Lead Removal ◽  
Solution System ◽  
Freundlich Equation ◽  
Adsorption Data ◽  
C 30 ◽  
Alpha Alumina

The presence of toxic metals like lead, mercury, chromium, arsenic, etc. in water is major problem these days. This investigation involves the removal of lead from water by batch adsorption technique using α- alumina (A12O3) as adsorbent. Percentage adsorption was determined for alumina-lead solution system as a function of pH, temperature, contact time and adsorbate dose. The known quantities of lead in solutions have been adsorbed on α-alumina and the concentration of lead in the solution after adsorption was determined by atomic absorption spectrophotometer. Maximum adsorption of lead was observed at pH 10, temp.15°C, 30 minutes and low adsorbate dose. Adsorption data has been interpreted in terms of Freundlich equation. The results suggest that α-alumina is effective adsorbent for lead removal. Key words: Toxic metals; Adsorbent; α-Alumina DOI: 10.3329/bjsir.v44i4.4589 Bangladesh J. Sci. Ind. Res. 44(4), 403-406, 2009

scholarly journals Benzene Removal by Iron Oxide Nanoparticles Decorated Carbon Nanotubes

2016 ◽  
Vol 2016 ◽  
pp. 1-10 ◽  
Author(s):  
Aamir Abbas ◽  
Basim Ahmed Abussaud ◽  
Ihsanullah ◽  
Nadhir A. H. Al-Baghli ◽  
Marwan Khraisheh ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Iron Oxide ◽  
Iron Oxide Nanoparticles ◽  
Contact Time ◽  
Batch Adsorption ◽  
Oxide Nanoparticles ◽  
Order Kinetic ◽  
Initial Concentration ◽  
Adsorbent Dosage ◽  
Benzene Removal

In this paper, carbon nanotubes (CNTs) impregnated with iron oxide nanoparticles were employed for the removal of benzene from water. The adsorbents were characterized using scanning electron microscope, X-ray diffraction, BET surface area, and thermogravimetric analysis. Batch adsorption experiments were carried out to study the adsorptive removal of benzene and the effect of parameters such as pH, contact time, and adsorbent dosage. The maximum removal of benzene was 61% with iron oxide impregnated CNTs at an adsorbent dosage 100 mg, shaking speed 200 rpm, contact time 2 hours, initial concentration 1 ppm, and pH 6. However, raw CNTs showed only 53% removal under same experimental conditions. Pseudo-first-order kinetic model was found well to describe the obtained data on benzene removal from water. Initial concentration was varied from 1 to 200 mg/L for isotherms study. Langmuir isotherm model was observed to best describe the adsorption data. The maximum adsorption capacities were 987.58 mg/g and 517.27 mg/g for iron oxide impregnated CNTs and raw CNTs, respectively. Experimental results revealed that impregnation with iron oxide nanoparticles significantly increased the removal efficiency of CNTs.

scholarly journals Orange Peel As Low-Cost Adsorbent In The Elimination Of Cd(Ii) Ions: Kinetics, Isotherm, Thermodynamic And Optimization Evaluations

2020 ◽  
Author(s):  
Fola Temilade Akinhanmi ◽  
Edwin Andrew Ofudje ◽  
Idowu Abideen Adeogun ◽  
Aina Peter ◽  
Joseph Mayowa Ilo
Keyword(s):  
Contact Time ◽  
Adsorption Process ◽  
Low Cost ◽  
Orange Peel ◽  
Polluted Water ◽  
Batch Adsorption ◽  
Order Kinetic ◽  
Human Beings ◽  
Solution Ph ◽  
Adsorbent Dosage

Abstract The presence of heavy metals in polluted water is known not only to cause stern harm to marine organisms but also to terrestrial plants and animals including human beings. This research applied low-cost and environmental benign adsorbent primed from waste orange peel (OP) for the removal of Cd(II) ions from aqueous solution via batch adsorption process. The surface properties of the orange peel powder were studied using Scanning Electron Microscopy (SEM), X-ray spectroscopy (XRD) and Fourier Transform Infrared Spectroscopy (FT-IR). Operational conditions like temperature, contact time, sorbent dosage, solution pH and initial adsorbate concentration were investigated. The utmost uptake of Cd(II) ion was obtained at a contact time of 120 mins, initial metal concentration of 240 mg/L, adsorbent dosage of 0.04 g/L, temperature of 45 °C and solution pH of 5.5. Equilibrium results showed that the orange peel adsorbent has an adsorption capacity of 128.23 mg/g as obtained from the Langmuir isotherm. The adsorption kinetics data followed a pseudo-first-order kinetic model with correlation coefficient (R2) >0.9 and low standard % error values. The adsorption process was found to be endothermic in nature with enthalpy of 0.0046 kJ mol−1 and entropy of-636.865 Jmol-1K-1 respectively. Results from the optimization study indicated that higher adsorbent dosage and lower Cd(II) ion concentration increased the percentage of Cd (II) ion removal. Thus, orange peel could be used in the removal of Cd(II) ion from aqueous solutions.

Zinc removal from aqueous solution using novel adsorbent MISCBA

2016 ◽  
Vol 6 (3) ◽  
pp. 377-388 ◽  
Author(s):  
Ibrahim Umar Salihi ◽  
Shamsul Rahman Muhamed Kutty ◽  
Muhamed Hasnain Isa ◽  
Nasir Aminu
Keyword(s):  
Heavy Metals ◽  
Aqueous Solution ◽  
Metal Ions ◽  
Contact Time ◽  
Adsorption Process ◽  
Negative Impact ◽  
Batch Adsorption ◽  
Maximum Adsorption Capacity ◽  
Adsorbent Dosage ◽  
Zinc Removal

Pollution caused by heavy metals has become a serious problem to the environment nowadays. The treatment of wastewater containing heavy metals continues to receive attention because of their toxicity and negative impact on the environment. Recently, various types of adsorbents have been prepared for the uptake of heavy metals from wastewater through the batch adsorption technique. This study focused on the removal of zinc from aqueous solution using microwave incinerated sugarcane bagasse ash (MISCBA). MISCBA was produced using microwave technology. The influence of some parameters such as pH, contact time, initial metal concentration and adsorbent dosage on the removal of zinc was investigated. The competition between H+ and metal ions has affected zinc removal at a low pH value. Optimum conditions for zinc removal were achieved at pH 6.0, contact time 180 min and adsorbent dosage of 10 g/L, respectively. The maximum adsorption capacity for the removal of zinc was found to be 28.6 mg/g. The adsorption process occurred in a multilayered surface of the MISCBA. Chemical reaction was the potential mechanism that regulates the adsorption process. MISCBA can be used as an effective and cheap adsorbent for treatment of wastewater containing zinc metal ions.

Sign in / Sign up

Export Citation Format

Share Document