scholarly journals Тонкие пленки селенида меди(I): состав, морфология, структура, оптические свойства

2018 ◽  
Vol 52 (10) ◽  
pp. 1213
Author(s):  
Л.Н. Маскаева ◽  
Е.А. Федорова ◽  
В.Ф. Марков ◽  
М.В. Кузнецов ◽  
О.А. Липина ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Diffuse Reflection ◽  
Optical Band Gap ◽  
Optical Transitions ◽  
Energy Dispersive Analysis ◽  
Hole Conductivity ◽  
X Ray Diffraction ◽  
X Ray ◽  
Optical Absorbance ◽  
Scanning Electron

AbstractThe systematized results of studies of the composition, morphology, structure, optical properties, and conductivity of hydrochemically deposited copper(I) selenide thin films (Cu_1.8Se) with the thickness of 390–400 nm are reported. The studies are carried out using scanning electron microscopy, energy-dispersive analysis, X-ray diffraction analysis, and X-ray photoelectron spectroscopy. The hole conductivity of the layers is established by the thermopower technique. The optical band gap determined from the results of studies of optical absorbance and diffuse reflection spectra of the films at 298 K is 2.5 and 1.84 eV for direct and indirect optical transitions, respectively.

Preparation of Visible-Light-Responsive TiO2-xNx Photocatalyst by a Very Simple Method

2011 ◽  
Vol 383-390 ◽  
pp. 3188-3191
Author(s):  
Han Jie Huang ◽  
Wen Long She ◽  
Ling Wen Yang ◽  
Hai Peng Huang
Keyword(s):  
Photocatalytic Activity ◽  
Visible Light ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflection ◽  
Ammonia Solution ◽  
Reflection Spectra ◽  
X Ray Diffraction ◽  
Simple Method ◽  
X Ray ◽  
Light Excitation

A visible-light-responsive TiO2-xNx photocatalyst was prepared by a very simple method. Ammonia solution was used as nitrogen resource in this paper. The TiO2-xNx photocatalyst was characterized by X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET), UV-Vis diffuse reflection spectra (DRS), and X-ray photoelectron spectroscopy (XPS). The ethylene was selected as a target pollutant under visible light excitation to evaluate the activity of this photocatalyst. The new prepared TiO2-xNx photocatalyst with strong photocatalytic activity under visible light irradiation was demonstrated in the experiment.

ROOM TEMPERATURE PHOTOLUMINESCENCE OF POLYCRYSTALLINE SIC PREPARED FROM CARBON-SATURATED SI MELT

2002 ◽  
Vol 16 (06n07) ◽  
pp. 1047-1051
Author(s):  
JIANPING MA ◽  
ZHIMING CHEN ◽  
GANG LU ◽  
MINGBIN YU ◽  
LIANMAO HANG ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Room Temperature ◽  
Uv Light ◽  
X Ray Diffraction ◽  
X Ray ◽  
Room Temperature Photoluminescence ◽  
Composition And Structure ◽  
Light Excitation ◽  
Scanning Electron

Intense photoluminescence (PL) has been observed at room temperature from the polycrystalline SiC samples prepared from carbon-saturated Si melt at a temperature ranging from 1500 to 1650°C. Composition and structure of the samples have been confirmed by means of X-ray photoelectron spectroscopy, X-ray diffraction and scanning electron microscopy. PL measurements with 325 nm UV light excitation revealed that the room temperature PL spectrum of the samples consists of 3 luminescent bands, the peak energies of which are 2.38 eV, 2.77 eV and 3.06 eV, respectively. The 2.38 eV band is much stronger than the others. It is suggested that some extrinsic PL mechanisms associated with defect or interface states would be responsible to the intensive PL observed at room temperature.

scholarly journals FTIR and Optical Properties of NiO Doped Cr2O3 Nanopar-ticles Synthesis by Hydrothermal Method

2018 ◽  
Vol 29 (1) ◽  
pp. 168
Author(s):  
Tunis Balassim Hassan
Keyword(s):  
Optical Band Gap ◽  
Average Crystallite Size ◽  
Structural Behavior ◽  
X Ray Diffraction ◽  
Nanopar Ticles ◽  
Hydrothermal Technique ◽  
X Ray ◽  
Cr2o3 Nanoparticles ◽  
Xrd Patterns ◽  
Scanning Electron

Pure and Nickel oxide doped chromium (III) oxide (Cr2O3) nanoparticals are synthesized by hydrothermal technique. The effect of dopant Ni concentration on the structural behavior of Cr2O3 nanoparticles was examined by X-ray diffraction. The average crystallite size of the synthesized nanoparticles was measured from XRD patterns using Scherrer equation and was decreased from 22nm to 12.9 nm with the increasing Nio concentration in Cr2O3 from (0, 0.01, 0.06, and 0.10). Morphologies and compositional elements of the synthesized nanoparticles were observed by the field emission scanning electron microscopy (FESEM) and energy dispersive X-ray (EDX) spectroscopy, respectively. The optical property of the samples was measured by ultraviolet - visible (UV-Vis.) absorption spectroscopy. The observed optical band gap value ranges from 2.3eV to 2.5eV for Ni doped nanoparticles

Synthesis and characterization of homogeneous lead-substituted tin oxide with the (110) face of rutile structure

2000 ◽  
Vol 15 (10) ◽  
pp. 2076-2079
Author(s):  
Chika Nozaki ◽  
Takashi Yamada ◽  
Kenji Tabata ◽  
Eiji Suzuki
Keyword(s):  
Electron Microscopy ◽  
Tin Oxide ◽  
Photoelectron Spectroscopy ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
Rutile Structure ◽  
X Ray ◽  
Transmission Electron ◽  
Scanning Electron

Synthesis of a rutile-type lead-substituted tin oxide with (110) face was investigated. The characterization was performed by x-ray diffraction, scanning electron microscopy, transmission electron microscopy, energy dispersive x-ray spectroscopy, infrared spectroscopy, x-ray photoelectron spectroscopy, and Brunauer–Emmett–Teller surface area measurements. The homogeneous rutile-type lead-substituted tin oxide was obtained until 4.1 mol% of tin was substituted with lead. The surface of obtained oxide had a homogeneously lead-substituted (110) face.

scholarly journals Reduced Graphene Oxide–Epoxy Grafted Poly(Styrene-Co-Acrylate) Composites for Corrosion Protection of Mild Steel

Coatings ◽  
2019 ◽  
Vol 9 (10) ◽  
pp. 666
Author(s):  
Xinchuan Fan ◽  
Yue Hu ◽  
Yijun Zhang ◽  
Jiachen Lu ◽  
Xiaofeng Chen ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Graphene Oxide ◽  
Reduced Graphene Oxide ◽  
Photoelectron Spectroscopy ◽  
X Ray Diffraction ◽  
Corrosion Properties ◽  
X Ray ◽  
Transmission Electron ◽  
Reduced Graphene ◽  
Scanning Electron

Reduced graphene oxide–epoxy grafted poly(styrene-co-acrylate) composites (GESA) were prepared by anchoring different amount of epoxy modified poly(styrene-co-acrylate) (EPSA) onto reduced graphene oxide (rGO) sheets through π–π electrostatic attraction. The GESA composites were characterized by Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS). The anti-corrosion properties of rGO/EPSA composites were evaluated by electro-chemical impedance spectroscopy (EIS) in hydroxyl-polyacrylate coating, and the results revealed that the corrosion rate was decreased from 3.509 × 10−1 to 1.394 × 10−6 mm/a.

Effect of Cu Content on the Tribological Performance of Cr-N Coatings at High Temperatures (840°C)

2009 ◽  
Author(s):  
Kyriaki Polychronopoulou ◽  
Claus Rebholz ◽  
Nicholaos G. Demas ◽  
Andreas A. Polycarpou ◽  
P. N. Gibson
Keyword(s):  
Vapor Deposition ◽  
Photoelectron Spectroscopy ◽  
Physical Vapor Deposition ◽  
Tribological Performance ◽  
X Ray Diffraction ◽  
X Ray ◽  
Cu Content ◽  
Glancing Angle ◽  
Scanning Electron ◽  
Ball On Disc

Cr-N and Cu-Cr-N coatings with Cu content between 3–65 at.%, Cu/Cr ratios in the 0.04–4.5 range and 21–27 at.% N, synthesized by twin e-beam Physical Vapor Deposition (EBPVD) at 450°C, were investigated. Using X-ray photoelectron spectroscopy (XPS), glancing angle X-ray diffraction (GAXRD) and scanning electron microscopy (SEM), in combination with nanoindentation mechanical property measurements and laboratory controlled ball-on-disc sliding experiments, it is shown that Cu-Cr-N coatings with low Cu content (3 at.%) possess sufficient wear resistance for high temperature demanding tribological applications.

Synthesis, Structural Analysis of Cadmium Sulphide Nanocrystallites

2019 ◽  
Vol 969 ◽  
pp. 169-174
Author(s):  
R. Sivanand ◽  
S. Chellammal ◽  
S. Manivannan
Keyword(s):  
Size Variation ◽  
Cadmium Sulphide ◽  
Xrd Analysis ◽  
Sem Analysis ◽  
Precipitation Method ◽  
Capping Agent ◽  
Energy Dispersive Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

In this paper, the effect of size variation of cadmium sulphide nanocrystallites which have been prepared by precipitation method is analyzed. These prepared samples were studied using X-ray diffraction (XRD), Scanning electron microscopy (SEM), and Energy dispersive analysis of spectroscopy (EDAX) techniques. SEM analysis represents the morphological nature of prepared samples and EDAX indicates the confirmation of elements present in the sample. XRD analysis determines the size of the samples and identifies the structure using miller indices (h k l values) of the nanocrystallies matches with JCPDS. From the XRD analysis, the size variation which depends on dopant, capping agent are discussed and corresponding results are reported in this paper.

scholarly journals Preparation of Cerium Dioxide Layers on Titanium by Electrodeposition with Organic Solution

2017 ◽  
Vol 2017 ◽  
pp. 1-9
Author(s):  
Vaijayanti Namdeo Nande ◽  
Diana Kostyukova ◽  
Jeonghee Choi ◽  
Yong Hee Chung
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Cerium Dioxide ◽  
Average Crystallite Size ◽  
X Ray Diffraction ◽  
Organic Solution ◽  
X Ray ◽  
Titanium Foils ◽  
Scanning Electron

Layers of cerium dioxide nanoparticles were prepared on titanium by electrodeposition with organic solution. Three concentrations of cerium ions were used at 31.6 V. The organic solution was isobutanol and titanium foils were used as anodes and cathodes. Currents were monitored during the electrodeposition. Deposition times ranged from 0.5 to 8 h. Deposited Deposited layers were calcined at 700 K for 30 min. The morphology and composition of the deposited layers were examined by scanning electron microscopy (SEM), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). As-prepared and calcined deposition layers were assayed to be cerium dioxide. The average crystallite size increased from 4 to 7 nm through calcination at 700 K. Sizes of calcined cerium oxide agglomerates were ranging from 73 to 146 nm for 30 min deposition and 209 to 262 nm for 8 h deposition. The electrodeposition efficiencies of 0.5 h deposition at three concentrations were measured to be highest.

Photoelectrocatalytic Degradation of HCB by N-Doped TiO2 Nanotube Arrays

2013 ◽  
Vol 652-654 ◽  
pp. 1580-1584
Author(s):  
Yu Jiang Guan ◽  
Zi Bo Wang ◽  
Shu Li Bai ◽  
Qin Xue
Keyword(s):  
Photoelectron Spectroscopy ◽  
Ph Value ◽  
Nanotube Arrays ◽  
Simulated Sunlight ◽  
X Ray Diffraction ◽  
X Ray ◽  
Photoelectrocatalytic Degradation ◽  
Doping Behavior ◽  
Doped Titanium Dioxide ◽  
Scanning Electron

N-doped Titanium dioxide (TiO2) nanotube arrays were characterized by scanning electron microscope (SEM)，X-ray Diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) to analyse its surface morphology, crystal types and the doping behavior of nitrogen. The material was used as electrode for photoelectrocatalytic degradation of hexachlorobenzen under irradiation of simulated sunlight. The effects of photocatalysis, electrocatalysis, photoelectrocatalysis, the concentration of Na2SO4 and pH value on degradation of HCB were investigated.

Preparation and Characterization of N Doped TiO2/ Sepiolite Composite Materials

2011 ◽  
Vol 284-286 ◽  
pp. 597-600
Author(s):  
Dai Mei Chen ◽  
Hai Peng Ji ◽  
Jian Xin Wang ◽  
Jian Chen ◽  
Xin Long Luan ◽  
...  
Keyword(s):  
Composite Materials ◽  
Photoelectron Spectroscopy ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
X Ray ◽  
Nitrogen Doped ◽  
Nitrogen Contents ◽  
Scanning Electron ◽  
Oxygen Atoms

Nitrogen doped TiO2/sepiolite composite materials (N-TiO2/sep) with different nitrogen contents were prepared by a sol-gel method and characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), respectively. XRD and SEM results showed that anatase-TiO2nanoparticles were distributed homogenously on the surface of sepiolite. XPS revealed that N atoms could incorporate into the lattice of anatase TiO2substituting the oxygen atoms sites of oxygen atoms.

Sign in / Sign up

Export Citation Format

Share Document